When I turn my steering wheel it changes the volume on my Android multimedia player (Model number attached) I was wondering if this was a setting I can turn off. It doesn't just happen when reversing. I recorded a video whilst stationary and as you can see when I turn the wheel it turns the volume up,
Any help would be appreciated.
Thanks
VID-20210914-WA0045_1.mp4
drive.google.com
Just a guess....
Your CanBus box may be set wrong and confusing the steering angle for the steering wheel volume control. Try going into factory settings and changing the can bus box settings.
Bob_Sanders said:
Just a guess....
Your CanBus box may be set wrong and confusing the steering angle for the steering wheel volume control. Try going into factory settings and changing the can bus box settings.
Click to expand...
Click to collapse
The canvas is currently set to no canbus, should I change that?
Related
I started this thread in order to help myself and others get their Steering Wheel Controls working. I'll start off with my setup:
2007 Chevy Silverado Extended Cab ON-STAR, No BOSE, No Amp
Axxess GMOS-LAN-012 GM LAN29 Data OnStar, Satellite, Chime Retention Interface
Axxess ASWC Steering Wheel Control Adapter
Connections made:
Pink from Axxess Interface > Pink Axxess ASWC (Pin7)
Pink from Joying (Key 2) > Pink from 3.5mm Jack (Cut Plug) Axxess ASWC
Brown from Joying (Key 1) > White from 3.5mm Jack (Cut Plug) Axxess ASWC
ASWC Red and Black goes to Interface Red and Black (ACC Power and Ground)
Programming:
Ign ON / Radio booted (Give it 15-20 sec after boot to load all apps)
Press the RESET on the ASWC for 2-5 seconds and release (hold for no more than 10 sec or you will be in manual programing mode)
LED on the ASWC should be flashing rapidly
Almost immediately after releasing the RESET button start pressing the VOL + on your steering wheel repeatedly until the LED turns off
The LED should remain off for 1-2 seconds then flash 7 times (Car detected on Pin 7 Pink) and pause.
The LED should now blink 1 time (Radio HU detected type 1 Eclispe)
The LED should now be ON (Not Flashing)
You may have to do this a couple of times to get the timing right.
Using the steps above NOT all but some of the buttons started working.
VOL+, VOL-, SOURCE, UP, DOWN
You can now map those keys to various Radio functions under Settings -> Car -> Steering Wheel
I tried to go into manual mode on the ASWC to assign all the buttons but at least according to their instructions never could get it to detect anything. Might be because of the way the Axxess interface retains ONSTAR etc... who knows...
Anyway hope this helps someone.
Fyi tried the PAC SWI JACK adapter could not get it to detect anything. I tried all radios.
Sent from my SM-N910P using Tapatalk
i got my Joying as a Jeep specific model, so the SWC worked right out of the box. However i recall reading about other people setting up various other head units on Jeep forums, and the name "Axxess ASWC" seems to ring a bell with people not getting them to work
Maybe they will come out with a Silverado or GM version... I'm good with what I have. Vol+ Vol- Source/ (Long Press HOME) Scan up Reassigned Scan Down to MUTE
I have a Honda Fit 2015
I got the ASWC-1 set up and it senses the bluetooth keys in manual program. Atoto will not see those keys when press them. The other keys work fine if you pick the right head unit configuration. I've tried them all and none of the 3 bluetooth (pickup, hangup, ptt) will work with the Atoto. I've also tried manually programming them for vol up/down or other keys like source but it doesn't matter it does nothing.
Any suggestions?
Hi all
I installed an Android (10) multimedia in my car. It was purchased from a seller called Autotop on Aliexpress, and everything seem to be working well including the steering wheel buttons.
Only problem is that I would like to set each button on the steering to do other functions then set by default and it simply doesn't work.
When I go to Settings > Steering wheel settings, it asked me to push the buttons and program them, but when I do that either nothing happenes or the buttons who are already set will do the action they supposed to, means the app doesn't communicate with the steering buttons.
Will appreciate any help to program these buttons.
*I noticed a similar thread here from 3 yrs ago, no solution there, hopefully now there is.
Trying to get my factory steering wheel controls to work with my atoto stereo. The Pac module is set to 7, and it blinks when I press a button, but when I go into the settings on the a6 it pick up that I'm pressing any buttons. I've tried wiring the blue w/yellow wire to both of the steering wheels wires of the a6 and have gotten no luck. I had the atoto swc in my last truck and it works fine with the swcir plugged in but I'd rather use my factory buttons then there little wheel.
I have Junsun V1 head unit with LTE and canbox.
CAN settings is selected as "VW RZC".
Steering wheel buttons working good.
I have not connected KEY 1 and KEY 2. It`s not working. SWC is not working and that is ok, because CAN is working.
The problem is:
When I press volume UP on the wheel, volume down, next, prev - works good
When I press phone button on the steering wheel, the head unit open by default Bluetooth app.
So, when someone is calling to me, I can`t pick up the phone from the steering wheel, because Bluetooth app is opening.
Everything is coded in by CAN (VW RZC).
How to edit can settings? or how to upload new setting? How to change bluetooth for “pick up”?
Once again, please forget about key 1, key 2 and SWC.
Pure CAN recoding.
I would like to know the answer to how to recode CANBUS settings. My volume up and down keys work as expected, but my phone key opens the Bluetooth app also and I want to turn it into a "next track" button and the hang up button into a "previous track" button.
For your problem, there is a submenu in 8878. I think it is in "Other" but possibly in CAN that reverse volume up and down. That should fix that problem. If you can't figure it out I will check next time I'm in my van.