Hallo,
i've got in trouble. My op2 had lineage os 16.1 and twrp 3.2.1-0 . In case of some trouble with charging and no usb recognization i decided to flash it new (after a lot of other options). I wiped Dalvik/System/Data/internal storage. The result is now, that i've got just TWRP and no usb recognization. I blame.
I can go to fastboot - but this doesn't help with no usb-support ... also adb sideload.
Now my question is, can anyone help to hard reset it, or to help to get usb support?
Is there a possibility with the switches to hard reset the device?
THX a lot for answers
... is there no one could help me ??
Related
Hi All,
I try to install different ROMs and Ubuntu phone on my Nexus 4 to check it out..
Long story short,
I have a device and only boots into recovery mode... Everything else has been wiped !
USB doesn't work..
Recovery mode does not help because all files are wiped...
I'm hoping there is a way to get usb to work, so I can push recovery files/new img.. whatever is necessary..
any ideas ?
Thanks in advance !
Hi there,
So I did something really stupid and I wiped my phone while in recover mode trying to install a new ROM. And now I'm stuck with a useless phone that can only go into TWRP and Firmware Update Mode.
I've tried every method to unbrick my phone, and have a previous thread on this forum trying to get help (http://forum.xda-developers.com/showthread.php?p=48914581#post48914581), but nothing is working.
My question now is I'm running TWRP 6.3.2.2, If I buy a USB OTG cable and put my rom files on a USB thumbdrive, can I then install the rom from the usb? If so, where in the filesystem does this usb storage show up?
BraydenJW said:
Hi there,
So I did something really stupid and I wiped my phone while in recover mode trying to install a new ROM. And now I'm stuck with a useless phone that can only go into TWRP and Firmware Update Mode.
I've tried every method to unbrick my phone, and have a previous thread on this forum trying to get help (http://forum.xda-developers.com/showthread.php?p=48914581#post48914581), but nothing is working.
My question now is I'm running TWRP 6.3.2.2, If I buy a USB OTG cable and put my rom files on a USB thumbdrive, can I then install the rom from the usb? If so, where in the filesystem does this usb storage show up?
Click to expand...
Click to collapse
I believe only TWRP 2.6.3.4 can support OTG (I've been happy with it).
I think you may have to ADB push the files from PC over while in recovery (may need to look around).
My x722 has a boot loop, and I had not enabled usb debugging on it, now or the pc does not recognize, there is some way to solve
I had that Problem, too!
But I got it back going!
First, try to get into twrp again and re-flash your Rom+ Gapps.
If you have any other working ROM on your internal memory, you better flash that one!
If both is not available, conneect your leeco via USB to another phone and there, activate Media Transfer! On the other phone, you should See your Lex722 and can now send Files to it. Just replace your Pc with another Android. For me, that worked to get it going after hard brick. Was not recognized by PC and booted only into fastboot. Data were formatted...
Hi all,
I'm stucked in a bad situation, shortly, usb data transfer isn't working, but charging works. Tired new cable and also replaced it with new USB still no data transfer.
today for mistake i've erase everything inside data.
now i have op2 with TWRP 3.0.2-0, my last chance is to start wifi via terminal or any other way to copy any os image to op2
someone can please help me to do this ?
Thanks!
Hello,
I had LOS 17.1 on my tablet (Lenovo X704F). It worked fine apart from microsd reader). I tried to flash stock FW from XDA - https://forum.xda-developers.com/th...-verison-lenovo-tab4-10-t3921073/post79328701 but it keeps reboot all the the time. I cannot finish the basic configuration process. I found another version of stock FW, but to flash it I need to boot it in EDL mode:
https://www.magnetforensics.com/blog/qualcomm-phone-edl-mode/
So not having service cable, also cannot take it apart adb was my way last time. But now cannot enter usb debugging, so adb does not see my tablet connected to the PC.
Do you have any clues what else I could do?
It's a bit worrying how few responses to issues there are on here. Did you get anything resolved?