Hello,
The other night I was messing with my HU sold\made by XY Auto and the model is the 8227L_Demo. I must have cleared something in the factory settings because now my on screen climate controls are not showing. I would try to perform a recovery on the unit but it seems there is not any way to get into the recovery. My physical climate controls on the chassis still work. Picture attached of the entire unit I purchased back in 2018. All in all I think I messed something up with the CAN BUS in the software? All the wiring is still connected properly and no damage.
Anyone have any experience with this and maybe know how I can fix it? Anyone know how to get the unit into recovery mode? For recovery mode I've already tried disconnecting the power from the HU, holding in the Reset button while plugging the power back into the HU (I did have the ACC turned on while doing this) still no recovery mode. I also checked for a chip? C7 or something like that on the MB but I could not find it do to a short out as some others have stated it works on their HU's/
When I go into the Car Settings Menu, I logged into Factory Settings and I Properly set the CAN Set to Honda. I then went back out of the Factory Settings and then went into Car Settings where it says to "set in car". I pressed that button and then I get a message of "No Original vehicle settings function"
Any help, guidance, etc. is greatly appreciated and thanks in advance.
(I emailed XY Auto 2 days ago and no response from them yet)
From reading the posts, what has been considered and tried.
What do you want out of xda
Are you sure you have selected the correct CanBus type (e.g Bagu, AnyYuan, etc)? I doubt you will get a response from XY Auto as these 8227L units are for the most part unbranded generic head units. Have you tried contacting who you bought the head unit from (the reseller)?
Related
Hi,
I've bought a new Head Unit, and I wired everything on the car.
It's working like a charm, but, there a big but.
The Head Unit which should go to sleep / deep sleep or whatever when I remove my car key after 30 seconds, stays on.
For the time being I've unpluger the ACC cable (the red wire) so that the Head Unit only receives power when the car key is plugged in.
Do you know why am I facing this Issue and how to resolve it ? I had hope to enjoy a fast boot and not a full boot everytime I use my car.. it would be nice
I have another question also, if you know about it, I'm trying to get the light buttons always on, because they're not very visible to me. Si I went to the special menu (with the 126 code) and tried changing the parameter "Power LED control" to "By Power" instead of "By head light" but they still won't turn on unless head light is on. Am I missing something ?
I'm not sure what head unit you have but a) what is your amp wire from the head unit connected to? B) there's is usually an illumination wire, what is that connected to?
Sent from my SM-G950U using Tapatalk
Also do not know what head unit you have but it sounds like it is not wired up correctly.
If you dont get much help on these forums maybe go visit an auto electrician as they should be able to advise further.
Hi I have an android head unit for my car that I have managed to mess up by putting Spotify into the auto start slot (was navi) as I thought it would be good to come on at the start. The problem I now have is that is has the volume of the sat nav which goes down to 3 and then off. I've tried pressing the reset button on the front of the unit (nothing changed) and also uninstalling Spotify/Navi/maps and it's still the same ???
Is there a way to factory reset these head units?
Thanx for any help I receive ?
Hello. Recently I have bought 8227l 8" Android 8.1 head unit from Aliexpress, installed it using provided adapters and everything works fine but the head unit won't turn off when I pull out the key. When I turn it off with phisical power button, something like Always On screen with time and date shows and button lights is still on. As I can understand powering of the head unit is controlled via canbus decoder. But when I plug out canbus decoder nothing defferent happens, only radio doesn't show car parameters like fuel consumption, rpm, milleage etc. Can someone help me? Is it something wrong with wiring?
What does the reseller suggest?
turn off head unit
So i give you my experience with my head unit, when i activate wifi and turn off the light key stuck on after when i dactivate wifi of the head unit and turn it off the lights turn off
scytalemk said:
Hello. Recently I have bought 8227l 8" Android 8.1 head unit from Aliexpress, installed it using provided adapters and everything works fine but the head unit won't turn off when I pull out the key. When I turn it off with phisical power button, something like Always On screen with time and date shows and button lights is still on. As I can understand powering of the head unit is controlled via canbus decoder. But when I plug out canbus decoder nothing defferent happens, only radio doesn't show car parameters like fuel consumption, rpm, milleage etc. Can someone help me? Is it something wrong with wiring?
Click to expand...
Click to collapse
There are two type of +12v, one is permanent and another one is from Acc key, you may have switch that, try to look into that.
scytalemk said:
Hello. Recently I have bought 8227l 8" Android 8.1 head unit from Aliexpress, installed it using provided adapters and everything works fine but the head unit won't turn off when I pull out the key. When I turn it off with phisical power button, something like Always On screen with time and date shows and button lights is still on. As I can understand powering of the head unit is controlled via canbus decoder. But when I plug out canbus decoder nothing defferent happens, only radio doesn't show car parameters like fuel consumption, rpm, milleage etc. Can someone help me? Is it something wrong with wiring?
Click to expand...
Click to collapse
There is a mini connector on the main cable. If you detach it, unit will shut down when key is removed.
Did anyone figure out a solution for this
Hi, I have this chinese Android unit :
Model: 8227l
Build version: alps-mp-o1.mp5
Mcu: TS907.190518(W)
Mtc: ????????
Even if is some kind of fake, everything was working good, android auto with https://forum.xda-developers.com/android-auto/mtcb-software-development/app-running-android-auto-unit-t3537547 , swc buttons, radio, audio, open doors alert, everything. But at a certain point, swc buttons stopped working. Now they work only in the stock swc configuration app, but then if you press buttons nothing happens, no volume up or down, no play/pause, nothing.
I tried to analyze the issue but everything is locked and I cannot even access adb....
Try to search a lot the forum and internet (russian forum ) but did no make any step forward.
I am a developer and would not be scared about writing some code for this unit (Mcu / Mtc) but need some hint regarding how to proceed with this issue.
Any help would be REALLY welcome, any suggestions?
hi, did yous solve this?
Pinabello said:
Hi, I have this chinese Android unit :
Model: 8227l
Build version: alps-mp-o1.mp5
Mcu: TS907.190518(W)
Mtc: ????????
Even if is some kind of fake, everything was working good, android auto with https://forum.xda-developers.com/android-auto/mtcb-software-development/app-running-android-auto-unit-t3537547 , swc buttons, radio, audio, open doors alert, everything. But at a certain point, swc buttons stopped working. Now they work only in the stock swc configuration app, but then if you press buttons nothing happens, no volume up or down, no play/pause, nothing.
I tried to analyze the issue but everything is locked and I cannot even access adb....
Try to search a lot the forum and internet (russian forum ) but did no make any step forward.
I am a developer and would not be scared about writing some code for this unit (Mcu / Mtc) but need some hint regarding how to proceed with this issue.
Any help would be REALLY welcome, any suggestions?
Click to expand...
Click to collapse
Do u knw how to change the screen resolution of a vertical Android screen in reverse screen ?
tonyj224 said:
Do u knw how to change the screen resolution of a vertical Android screen in reverse screen ?
Click to expand...
Click to collapse
Hi.
I have the same version as you. Unfortunatly I can't help you. I just know that the swc are related to the canBus box.
But I would like to know if, by any chance, you have this HU installed in a Peugeot.
Do you have any idea what is this?
Pinabello said:
Hi, I have this chinese Android unit :
Model: 8227l
Build version: alps-mp-o1.mp5
Mcu: TS907.190518(W)
Mtc: ????????
Even if is some kind of fake, everything was working good, android auto with https://forum.xda-developers.com/android-auto/mtcb-software-development/app-running-android-auto-unit-t3537547 , swc buttons, radio, audio, open doors alert, everything. But at a certain point, swc buttons stopped working. Now they work only in the stock swc configuration app, but then if you press buttons nothing happens, no volume up or down, no play/pause, nothing.
I tried to analyze the issue but everything is locked and I cannot even access adb....
Try to search a lot the forum and internet (russian forum ) but did no make any step forward.
I am a developer and would not be scared about writing some code for this unit (Mcu / Mtc) but need some hint regarding how to proceed with this issue.
Any help would be REALLY welcome, any suggestions?
Click to expand...
Click to collapse
Hi!!! I would like to be a develloper as well! My unit is made of 2 parts: The radio and the Screen. Is installed (and perfectly fitting) a Peugeot 307 Phase 2 (I guess phase 1 are the cars with a smal display for temperature and time. Phase 2 are the cars that had a GPS originaly, and a upper screen - not a display). For me, the problem is that the software dont allow you to choose wich car type you have. I can select Peugeot 307 but not the type. My CanBus is HiWorld. It says 307, but not specific model. I would like this changes: When I press the button for OnBoard Computer, It should go to the trip menu. Also, the car Settings (like AC and door lock) are not working and they blink (selected, notSelected).
There is a miscomunication there. I cant find help!!!!
Hi,
I have done a factory reset to my radio and now the left buttons stop working... Only the screen buttons ate working... Any ideas to solve this problem?
Thanks
Hi, ask your seller to give you files (for factory settings) needed to import physical buttons into device again.
Minute of work and then restart.
Oh... Really... It need some files? Hope the seller send it to me.
I completely noob on this time on rádios... Android
I have those files but model of your device must be close to mine - 8227L ALPS FF5000
I'll reply as soon as possible.
This files how do we use it? Thanks.
nnexuss said:
I'll reply as soon as possible.
This files how do we use it? Thanks.
Click to expand...
Click to collapse
Please take picture of your device externaly with all buttons visible.
Then I will see if it is a match for this device.
Photos added.
Any suggestions?
Thanks
Anton TNT said:
Please take picture of your device externaly with all buttons visible.
Then I will see if it is a match for this device.
Click to expand...
Click to collapse
Hi Anton
Can you hel me please?
nnexuss said:
Hi Anton
Can you hel me please?
Click to expand...
Click to collapse
By the photos you posted this device is similar that I'm using in my car, TS10 or TS18 topway branded, it must have option to update system and MCU online, so do an update online (car settings/factory settings/update).
If updating does not help try calibration of screen (activated by pressing all five fingers on screen I think). There is no physical buttons on this device and it must have canbus box right ?
Anton TNT said:
By the photos you posted this device is similar that I'm using in my car, TS10 or TS18 topway branded, it must have option to update system and MCU online, so do an update online (car settings/factory settings/update).
If updating does not help try calibration of screen (activated by pressing all five fingers on screen I think). There is no physical buttons on this device and it must have canbus box right ?
Click to expand...
Click to collapse
Everything it's working now... Except the remap of the steering wheel... I can't config which function will do each button
This is the main objective 4 me.
When I go to the config menu, press start the config and when press the button on steering wheel nothing happened.
Only volume works and the doors too... If I open a door a imagem pop up on the screen
nnexuss said:
Everything it's working now... Except the remap of the steering wheel... I can't config which function will do each button
This is the main objective 4 me.
When I go to the config menu, press start the config and when press the button on steering wheel nothing happened.
Only volume works and the doors too... If I open a door a imagem pop up on the screen
Click to expand...
Click to collapse
Wrong settings in canbus software - go to factory settings and download/load correct software for canbus device (your car model) and restart, it should work
Anton TNT said:
Wrong settings in canbus software - go to factory settings and download/load correct software for canbus device (your car model) and restart, it should work
Click to expand...
Click to collapse
Now ... other problem :/ some how the app as gone.
cant see the video
Anton TNT said:
cant see the video
Click to expand...
Click to collapse
Try it now please
which canbus settings was prior of changing ? SIMPLE or RAISE or HIWORLD ?
I think this wrong settings caused this. Rerturn old state but do not change first option , If canbus sticker on the box is simple then it is simple in first option - get it ? If it is something else choose this one and then choose software for device and model.
Anton TNT said:
I have those files but model of your device must be close to mine - 8227L ALPS FF5000
Click to expand...
Click to collapse
I have same problem but my unit is V1c 1G - after activating can bus it made APK installation and then the side buttons doesn't work. Here is a photo of unit which is for a Ford Focus MK2.5
Any help much appreciated
Chris
Choose right software for your device and canbus (read which canbus is from sticker on canbus box and then choose from list like if it is RAISE canbus in first section choose RAISE, then in second choose car model and then on next PUBLIC)
Anton TNT said:
Choose right software for your device and canbus (read which canbus is from sticker on canbus box and then choose from list like if it is RAISE canbus in first section choose RAISE, then in second choose car model and then on next PUBLIC)
Click to expand...
Click to collapse
This is my can bus box - doesn´t tell anything about type of can bus. But is it related to can bus? My steering wheel buttons work but not the buttons on the head. I would imagine that it is something else.
Regards Chris
Here is a photo of the set up. Steering wheel buttons work, center console info works. Side buttons on head unit doesn't work.
cl3884 said:
Here is a photo of the set up. Steering wheel buttons work, center console info works. Side buttons on head unit doesn't work.
Click to expand...
Click to collapse
Ths is ok, but must ask your seller for update of files for physical buttons, they only have it. You will not find this on net.