Hi guys years ago i switch the rom from my coolpad to cuoco92 and it showed many bugs with apps, i tried to update the rom to a newer version but i didn't know that you must update twrp for that to. So i literally bricked my phone... and now there's no much help in internet like was back them.
I tried to unbrick with flash tool but it need scatter rom (i don't know where i can get those roms),
On coolpad pst but it shows an error "check thread the version of cpb don't support been downloaded.
I tried with qgdp and ygdp but i only got the same error over and over saying the following messages...
13:49:32 CELL2: V3.2.6.0
13:49:32 CELL2: Cell 2 USB address is: 6&5FCEF7&0&1
13:49:34 CELL2: Download Started...
13:49:34 CELL2: Downloading CPB:
13:49:34 CELL2: Init DownQueue...
13:49:34 CELL2: Device connected, start to download ...
13:49:34 CELL2: Get bootloader information ...
13:49:34 CELL2: Bootloader will not use CRC while system img!
13:49:34 CELL2: Bootloader does not support querying CID !
13:49:34 CELL2: Bootloader does not support querying Secure !
13:49:34 CELL2: Check device ...
13:49:34 CELL2: Check phone name fail, The phone name 'C106' not contained in 'C1'
13:49:34 CELL2: Check phone name fail, Please check the 'ProductName' in the PhoneInfo.yl
13:49:34 CELL2: Check phone name fail !, msg:C106_P4
13:49:34 CELL2: Download failed,please try again!!
13:49:34 CELL2: Total download time elapsed: 0 min : 0 sec
13:49:34 CELL2: Downloading all files: Failed!
I tried to rename the command line with the name of phone but it doens't work too... Now i don't know what else i can do...
Help me please! =ยด[
I think it'll better to try flash using QPST/QFIL tool or Miflash tool . Reboot phone to EDL mode , hold down all three buttons until led blinks.
Related
Ok i have te watch conected to mtk flash tool, i tried to readback but it give me a error it says: flash tool error : S_FILE _IO_FAIL (1039)
Any help?
Hi, I have downgraded my yu yureka from yu os 6.0 to cm 12.1 through fastboot method
but since then i am facing issues such as wifi only working for first half hour after first reboot then showing mac address unavailable and same issue with bluetooth and neither of them works.
tried flashing stock rom through fastboot method same issue persists and the issue is present in all roms i have tried.
tried to flash firmware using annabathina tool and lost imei but later recovered imei using qxdm tool, giving the links i have used.
https://forum.xda-developers.com/yureka/orig-development/tool-brick-yureka-device-using-t3442862
https://forum.xda-developers.com/yureka/help/recovering-lost-imei-yu-yureka-yunique-t3331485
wifi and bluetooth problem existed even after doing this and new problems surfaced. i was unable to flash recovery like twrp from then on wards only one twrp version i.e older version working.
then again i tried to flash using ygdp tool but receiving error mesages
10:35:48 CELL0: Software Version: Assembly - <V3.98_141222_02>
10:35:48 CELL0: Cell 0 USB address is: 4A2214B
10:35:50 CELL0: Waiting for device ready ...
10:35:52 CELL0: Init download info ...
10:35:52 CELL0: Init complete! Start ...
10:35:52 CELL0: Download Started...
10:35:52 CELL0: Downloading CPB:
10:35:52 CELL0: Init DownQueue...
10:35:52 CELL0: 4.4.035.00.P1.150420.8675_I01_ROM
10:35:52 CELL0: Device connected, start to download ...
10:35:52 CELL0: Get bootloader information ...
10:35:52 CELL0: Bootloader is old !
10:35:52 CELL0: Bootloader will not use CRC while system img!
10:35:52 CELL0: Bootloader supports querying CID!
10:35:52 CELL0: Bootloader supports querying Secure !
10:35:52 CELL0: Check device ...
10:35:52 CELL0: Check CID Pass.
10:35:52 CELL0: Unknown error:5 ,last error:997, msg:cp8675_S10_P1
10:35:52 CELL0: Download faile,please try again!!
10:35:52 CELL0: Total download time elapsed: 0 min : 0 sec
10:35:52 CELL0: Downloading all files: Failed!
any help regarding restoring my yureka back will be helpful
does qualcomm qloader method works?
or are there any other methods?
is it a hardware issue?
what kind of method do service center guys use to flash our phones?
Hello community,
Does anyone was able to flash prog_emmc_firehose_8936.mbn through QFIL to n910p?
I've tried several times since yesterday to unbrick the phone itself, but keep receiving next message:
PHP:
Start Download
Program Path:C:\Users\JHome\Desktop\samsung\8675_W00\prog_emmc_firehose_8936.mbn
COM Port number:3
Sahara Connecting ...
Sahara Version:2
Start Sending Programmer
Download Fail:System.Exception: Unable to download Flash Programmer using Sahara Protocol
at QC.QMSLPhone.Phone.QPHONEMS_SaharaArmPrgDownload(String sFileName)
at QC.SwDownloadDLL.SwDownload.QPHONEMSSaharaDownloadArmPrg(UInt64& version, String armPrgPath)
Download Fail:Sahara FailSahara Fail
Finish Download
Seems the problem is in prog_emmc_firehose_8936.mbn
Please someone share necessary .mbn file id any.
Thanx,
me too
help me
Tks all
Today i wanted to update my phone from cynaogenmod to a recent lineageos. It followed this guide jfltexx/install, but when i tried to "heimdall flash --RECOVERY ...", the blue progress bar on the phone got to ~99% - then heimdall crashed:
Code:
...
Downloading device's PIT file...
PIT file download successful.
Uploading RECOVERY
100%libusb: error [udev_hotplug_event] ignoring udev action bind
ERROR: Failed to confirm end of file transfer sequence!
ERROR: RECOVERY upload failed!
Ending session...
ERROR: Failed to send end session packet!
Releasing device interface...
Because at that point nothing would change anymore, i unplugged the phone and rebooted. Since then the phone won't boot android anymore and reports "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again." when booting to recovery mode. Download mode is still accessible, but worthless:
Flashing the original ROM fails with "Complete(Write) operation failed": imgur
Flashing it with a PIT i found on this forum doesn't work either: imgur
Is my phone completely lost? Is there something i can do?
aenderboy said:
Today i wanted to update my phone from cynaogenmod to a recent lineageos. It followed this guide jfltexx/install, but when i tried to "heimdall flash --RECOVERY ...", the blue progress bar on the phone got to ~99% - then heimdall crashed:
Code:
...
Downloading device's PIT file...
PIT file download successful.
Uploading RECOVERY
100%libusb: error [udev_hotplug_event] ignoring udev action bind
ERROR: Failed to confirm end of file transfer sequence!
ERROR: RECOVERY upload failed!
Ending session...
ERROR: Failed to send end session packet!
Releasing device interface...
Because at that point nothing would change anymore, i unplugged the phone and rebooted. Since then the phone won't boot android anymore and reports "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again." when booting to recovery mode. Download mode is still accessible, but worthless:
Flashing the original ROM fails with "Complete(Write) operation failed": imgur
Flashing it with a PIT i found on this forum doesn't work either: imgur
Is my phone completely lost? Is there something i can do?
Click to expand...
Click to collapse
Hello,
Please follow my Guides. I recommend you to follow the guide "clean install from scratch" and also use Odin. Everything you need it's on my thread and in my collection.
Issue Resolved
The solution was to use a shorter USB cable. Thank you so much for making me not loose my faith!
Days ago , i had an invalid boot image problem when i try to flash lineage os.Then i wiped internal storage and fix mount /data errors.But because of image file somehow my phone model and brand is changed.Then i discovered QFIL and use a solution from here for fix everything.It fixed everything but my phone was in Factory Mode.I tried an file i found on internet for fix and i flashed it with QFIL.But my device not open and i tried to flash qfil and qcn file again.It gives me error every time and i selected erase all before download.But 30 minutes after i press download my pc battery get low and turned off.
Now when i connect my device it says "USB device is not recognized.The last USB device you connected to this computer has malfunctioned and windows doesn't recognize it" . I tried change value of ErrorControl of USBSTOR in regedit but i cant find usbstor.inf in system32 after i did it.Now i have a phone with no vibration , no fastboot ,no recovery, no boot or edl.I tried edl points over and over again and i tried re-install drivers too.I cant see anything cause my phone cant boot.
My Device =Asus Zenfone Max (ZC500KL/ZO10D with Snapdragon 410)
ROM: Stock rom with Factory Mode
QFIL Port : No port (It didn't recognize )
Device Manager : unknown usb device (device descriptor request failed)
Error Code: A request for the USB device descriptor failed. CODE 43
Note:Sorry for my bad English.Please help
I press power button 10 sec and pc can't detect it but qfil can.So i tried again.But it gives me sahara error everytime
I am giving port traces and log files in below