Hi everyone,
so in my immense stupidity, I actually managed to set my phone password wrongly, and now I can't get in. Spent a day trying passwords to find the typo but that was unsuccessful.
I have crDroid Android 11, bootloader unlocked, rooted with magisk, and TWRP 3.5.0.
How can get my phone back? I would love to save the internal storage since I have important stuff, but you know, if wiping it is the only way I have to go for it.
Thanks in advance.
Use this method. I have seen many people online suggesting it works.
Remove /Bypass Lockscreen With Recovery
Recently when i restored my data using TWRP i faced a problem at lock screen. I was not able to unlock my phone with the pin i set Earlier..So after so many attempts i was able to find a solution for that problem.(works with pattern,pin etc)...
forum.xda-developers.com
You are essentially removing lockscreen settings completely and should work as you still have TWRP access.
madman said:
Use this method. I have seen many people online suggesting it works.
Remove /Bypass Lockscreen With Recovery
Recently when i restored my data using TWRP i faced a problem at lock screen. I was not able to unlock my phone with the pin i set Earlier..So after so many attempts i was able to find a solution for that problem.(works with pattern,pin etc)...
forum.xda-developers.com
You are essentially removing lockscreen settings completely and should work as you still have TWRP access.
Click to expand...
Click to collapse
Thanks for the responce, but unfortunately that didn't work.
I deleted the files as explained in the thread you linked but now the lockscreen doesn't work at all, it's just a black screen. The power menu appears if I hold the power button, but nothing else. I tried swiping in some direction on the black screen but it doesn't unlock.
Also tried to sideload the rom again (dirty and clean flash), and magisk, still no luck.
Read the entire thread but nothing helpful.
DarkLudo77 said:
Thanks for the responce, but unfortunately that didn't work.
I deleted the files as explained in the thread you linked but now the lockscreen doesn't work at all, it's just a black screen. The power menu appears if I hold the power button, but nothing else. I tried swiping in some direction on the black screen but it doesn't unlock.
Also tried to sideload the rom again (dirty and clean flash), and magisk, still no luck.
Read the entire thread but nothing helpful.
Click to expand...
Click to collapse
Is TWRP able to decrypt the data? I'm guessing that's a no as the password is not accepted by the lockscreen. If TWRP was magically OK with the password, you could have adb pulled the files.
But apart from reseting the lockscreen using TWRP, I don't know a way to fetch the files.
madman said:
Is TWRP able to decrypt the data? I'm guessing that's a no as the password is not accepted by the lockscreen. If TWRP was magically OK with the password, you could have adb pulled the files.
But apart from reseting the lockscreen using TWRP, I don't know a way to fetch the files.
Click to expand...
Click to collapse
TWRP can decrypt if the correct passoword is provided. Tried pulling with adb the files anyway, even if they are encrypted, but the phone doesn't allow that either.
Thanks anyway
Related
I have a new Galaxy Note 3 (having bricked one trying to understand why it wouldn't encrypt) and now with a full stock rom I still find that the phone is impossible to encrypt.
I have an encrypted SD card in it. (only thing I can think of that might be causing problems)..
Settings > General > Security > Encrypt Device keeps stopping after a single shutdown,
How the heck do I encrypt this thing?? - Am I missing the blindingly obvious..
Thanks
tahnoonp said:
I have a new Galaxy Note 3 (having bricked one trying to understand why it wouldn't encrypt) and now with a full stock rom I still find that the phone is impossible to encrypt.
I have an encrypted SD card in it. (only thing I can think of that might be causing problems)..
Settings > General > Security > Encrypt Device keeps stopping after a single shutdown,
How the heck do I encrypt this thing?? - Am I missing the blindingly obvious..
Thanks
Click to expand...
Click to collapse
I'm having the exact same issue. Encryption is requited to get my work email and I can't get it to go.
Finally got mine to encrypt
Took me a bunch of tries.. and finally once i opened a chat with samsung support it finally worked.. i was at 100% charge, plugged into the wall and if finally worked. not sure if thats a bug in its detection if your over the stated 80% or not... good luck.. i finally got it working though.. only did a fast encryption as it didn't work on previous tries either way... so i just chose one and tried it again.
tahnoonp said:
I have a new Galaxy Note 3 (having bricked one trying to understand why it wouldn't encrypt) and now with a full stock rom I still find that the phone is impossible to encrypt.
I have an encrypted SD card in it. (only thing I can think of that might be causing problems)..
Settings > General > Security > Encrypt Device keeps stopping after a single shutdown,
How the heck do I encrypt this thing?? - Am I missing the blindingly obvious..
Thanks
Click to expand...
Click to collapse
I have the Google Policy Manager and Encryption is required for me too. I started at 81% and the first time I did it, it just rebooted. The second time I did it it worked like it was suppose to. Try it again right after it reboots and see if it works.
Make sure the phone is charged and keep trying over and over.
It will work eventually.
I gave up. I'm using touchdown now for work email which will allow me to skip full device encryption
Sent from my SM-N900V using Tapatalk
Same problem here, it will not encrypt
....help please
This is the answer I found doing a couple of root and unroot
1.If you encrypt the device and then root it you will net get past the passcode in the phone (black screen)
2. If you root the phone first and ten try to encrypt you will get the problems mentioned in this thread
..any tips how to get the phone rooted and then encrypted?
greffel said:
This is the answer I found doing a couple of root and unroot
1.If you encrypt the device and then root it you will net get past the passcode in the phone (black screen)
2. If you root the phone first and ten try to encrypt you will get the problems mentioned in this thread
..any tips how to get the phone rooted and then encrypted?
Click to expand...
Click to collapse
Bump. I'm looking for this answer too.
digittante said:
Bump. I'm looking for this answer too.
Click to expand...
Click to collapse
anyone at all? im stuck. Bump!
was having a similar problem on nexus 4 but safe mode helped there.
dind't help on my new n3. shouldn't have rooted before encrypting.
tried pressing encrypt about 10 times.
tried boot into recovery + wipe . also tried safe mode. also tried unroot + factory reset (pretty sure recovery + wipe /data is the same as reset user data from settings).
waiting for the firmware image to download - decided to try a firmware reflash
and then before flashing it I tried rebooting to recovery and powering off and encrypting and it worked. or maybe it was that random 12th time it worked because of an unrelated reason.
and after trying to root it again it just booted to a black screen after cf-root and enter encryption password screen.
*sigh*
My Work-Around
svyr said:
and then before flashing it I tried rebooting to recovery and powering off and encrypting and it worked. or maybe it was that random 12th time it worked because of an unrelated reason.
and after trying to root it again it just booted to a black screen after cf-root and enter encryption password screen.
*sigh*
Click to expand...
Click to collapse
I'm an AT&T customer, but I bought a T Mobile Note 3 off of Craigslist, unlocked it, rooted using Chainfire's ODIN thread, and then used the RegionFree Lock Away app. I was unable to encrypt just like you guys until I did the following. Flashed TWRP tar file from the TWRP site using ODIN. Rebooted into recovery and made an image, backup up everything, just in case. Rebooted and went in the SU Superuser application that Chainfire originally installed and uninstalled through the settings in the program. Once I rebooted I was able to encrypt the device (without fast method), I already had my SD Card encrypted. Once I encrypted the device I downloaded Kingo Root at the advice of DesignGears and used the one click root application from the Kingo Root site (google it.) After I did that, I now have full root access back, encryption, and never had to uninstall the region lock, so I didn't lose phone connectivity, applications, or anything else during the process. I recommend using TitaniumBackup and syncing via Google Drive or Dropbox before you start the process so you can restore your apps and data, once again, just in case.
encrypted ATT Note 3 not able to root
I was able to unroot my ATT Note 3 and then encrypted it. But Kingo Root failed to root the device. (I used it to root the phone once previously)
Now I stuck in a status with encrypted phone not able to root anymore.
Any suggestions please?
GHolbrook4 said:
I'm an AT&T customer, but I bought a T Mobile Note 3 off of Craigslist, unlocked it, rooted using Chainfire's ODIN thread, and then used the RegionFree Lock Away app. I was unable to encrypt just like you guys until I did the following. Flashed TWRP tar file from the TWRP site using ODIN. Rebooted into recovery and made an image, backup up everything, just in case. Rebooted and went in the SU Superuser application that Chainfire originally installed and uninstalled through the settings in the program. Once I rebooted I was able to encrypt the device (without fast method), I already had my SD Card encrypted. Once I encrypted the device I downloaded Kingo Root at the advice of DesignGears and used the one click root application from the Kingo Root site (google it.) After I did that, I now have full root access back, encryption, and never had to uninstall the region lock, so I didn't lose phone connectivity, applications, or anything else during the process. I recommend using TitaniumBackup and syncing via Google Drive or Dropbox before you start the process so you can restore your apps and data, once again, just in case.
Click to expand...
Click to collapse
I was able to get mine to encrypt after killing the bloat apps. All Google sync, amazon, and Verizon services. I can't say which one was killing it since it stopped pretty much every app or service that wasn't critical to the device.
Can anyone confirm that Encryption will never work once we root our phone ?
nlatifolia said:
Can anyone confirm that Encryption will never work once we root our phone ?
Click to expand...
Click to collapse
Same question here... Anyone was able to encrypt after being rooted???
Same question, rooted can't encrypt.
Just got a note 3 and this is an old thread. So wanted to update this question.
To encrypt device after root all that is needed to do is run the following command from terminal or adb shell as root. You must have the latest busybox installed.
pkill -KILL daemonsu
After running this command you should be back at the "$" prompt and out of root. Do not run su again.
Then encrypt your device. Encryption should work fine. Once rebooted you will have root again.
I had to repeat the above steps because I ran su again. Running su restarts daemonsu.
Good luck
Hi,
I was able to root and encrypt my sm-n900 note3 using the steps mentioned on this post:
http://forum.xda-developers.com/showthread.php?t=2791587
Just make sure that you have your backups ready case something goes wrong
I've installed the bloatwares after rooting and encrypt.
I have a nexus 6P running rooted stock rom and I wanted to try out a new rom. Before flashing the new rom, I made a nandroid backup via TWRP. Now, the rom that I was backing up had fingerprint security setup with backup passcode for unlocking the phone.
So I tried new rom and it didn't work (read-too many issues and too many crashes). Decided to revert back to my original setup. Went back into TWRP and restored the backup.
After booting the phone up, I can't log in to my phone anymore. As you know after every reboot, fingerprint sensor doesn't work unless you enter the backup passcode. So I am entering my passcode and its not accepted. I have tried entering passcode many times but to no avail. I know my passcode so possibility of me forgetting it is not valid.
Has anybody else seen or ran into this issue yet?
The step folks are missing is Prior to installing a backup you Must Change security to None before you even start a backup This clears password, pin and saved finger prints. I believe once security is changed it is safe to backup and then install backup. You will need to reenter Pin and Fingerprints.
Born<ICs said:
The step folks ...
... is changed it is safe to install backup.
Click to expand...
Click to collapse
You mean clear the security before making a backup ... right?
if not, how would I change security on a backup file of rom that had security enabled.
I have never used lock screen security before so never ran into this issue.
No, dig through this forum for tech details. But my understanding is anytime you make/install a backup or reflash rom or go back to stock you must reset you Security options in settings to None. You have security now, probably Fingerprints, and the required Lockscreen Pin.
If you try to install backup or Rom or whatever without doing so you get what you experienced. There is a path out of it if you read further.
Pin or Pattern on boot after restoring Nandroid
Born<ICs said:
No, dig through this forum for tech details. But my understanding is anytime you make/install a backup or reflash rom or go back to stock you must reset you Security options in settings to None. You have security now, probably Fingerprints, and the required Lockscreen Pin.
If you try to install backup or Rom or whatever without doing so you get what you experienced. There is a path out of it if you read further.
Click to expand...
Click to collapse
The interesting thing is, I intentionally chose to enter pattern/pin on rebooting. The strange (actually may not be strange .....but strange to me) thing is that even when I move on to different Roms, that initial choice is remembered and embedded since even after choosing not to require pin/pattern when rebooting, I get prompted. Also the pin/pattern works during recovery, it also works on the initial startup after restoring a backup but then fails after successful fingerprint use (it will actually say "wrong pin" or "wrong pattern") at the end of the booting process. The thing is, I have only used one pin and at other times one password ever with this device. Eventually I had to do a factory reset to solve this issue (thank goodness I was able to back up my internal storage to my computer in TWRP recovery mode).
Hello all,
So in an absent minded spell I changed my screen pattern to a complicated one just to be more 'safe'. It hit me when i tried to unlock the phone seconds later that I had already forgotten the patter. . I know it is very stupid to **** around like that.
But silver lining is when the phone is paired with my Bluetooth headset the phone unlocks itself and I am able to go inside. This is due to Smart Lock feature which assumes my phone is safe when paired with Bluetooth headset.
But the main thing is I am not able to change the pattern itself as it asks for older pattern. I have read a lot of posts on how the pattern can be disabled by deleting gesture.key. It turns out getting super user permission to do that is very complicated. I have failed to change or disable the pattern so far.
Guys help!
kajang said:
Hello all,
So in an absent minded spell I changed my screen pattern to a complicated one just to be more 'safe'. It hit me when i tried to unlock the phone seconds later that I had already forgotten the patter. . I know it is very stupid to **** around like that.
But silver lining is when the phone is paired with my Bluetooth headset the phone unlocks itself and I am able to go inside. This is due to Smart Lock feature which assumes my phone is safe when paired with Bluetooth headset.
But the main thing is I am not able to change the pattern itself as it asks for older pattern. I have read a lot of posts on how the pattern can be disabled by deleting gesture.key. It turns out getting super user permission to do that is very complicated. I have failed to change or disable the pattern so far.
Guys help!
Click to expand...
Click to collapse
Its the only way to do it, the other way is to do a backup and then factory reset
PS: What made it difficult for you?
if you have a custom recovery, it is easy to pick up any zip file that is, for example, a mod, decompresses and only removes the metainfo file and create a zip that file and flashing, ready will restart without lock pattern without losing anything
Deleting gesture.key
ExCuTioN said:
Its the only way to do it, the other way is to do a backup and then factory reset
PS: What made it difficult for you?
Click to expand...
Click to collapse
Hi
I am able to go to adb shell and execute some commands. But not commands like delete which require Super user permissions. I am having hard time getting that. I am not well versed with command line.
Customer recovery
browcantor said:
if you have a custom recovery, it is easy to pick up any zip file that is, for example, a mod, decompresses and only removes the metainfo file and create a zip that file and flashing, ready will restart without lock pattern without losing anything
Click to expand...
Click to collapse
I have tried installing Twrp recovery, but it gives an error while installing. I am forgetting the exact error. I could not follow rest of what you are saying. I am relatively inexperienced. What is metainfo? Are talking about flashing new ROM?
I strongly suggest that you factory reset your device. It'll be simpler for you that don't have all the knowledge to do other way. Beside, doing so demands a rooted device. Also beside, with the Google account sync it's very easy to setup the device again.
https://drive.google.com/file/d/0B7C0PrsBvY69NU9JM0hJeEdQd2c/view?usp=drivesdk
Flashing
I'm running Carbon rom on my 6P, after getting around to flashing the flashabling zip for supersu, my pattern I use to boot into android(not the lockscreen pattern) no longer works.
It still asks for my pattern to start android, but when I put it in, it says it's not right. I've tried my pattern several times and a couple random ones to see if it just messed it up.
Is there something I can do in twrp to fix this? Or will I have to lose everything off my phone?
There's a sticky in the general section:
Https://forum.xda-developers.com/nexus-6p/general/psa-twrp-backups-lockscreen-security-t3245070
drnizeguy said:
There's a sticky in the general section:
Https://forum.xda-developers.com/nexus-6p/general/psa-twrp-backups-lockscreen-security-t3245070
Click to expand...
Click to collapse
I just had another person point me to that thread a few minutes ago. Deletion of the locksettings does nothing. I still have it asking for a pattern to start android.
xBr4v3x said:
...Is there something I can do in twrp to fix this? Or will I have to lose everything off my phone?
Click to expand...
Click to collapse
Nothing to do. Yes, you have already lost everything. Factory reset and start over. Most of the time this happens to people who have been running unencrypted, screw up, and then end up encrypted. NOT saying this is you because you seem to have at one time been encrypted and HAD a working boot PIN. One of the features of a true encrypted system is that once you lose the keys, nobody can help you. I usually keep a TiBu of all my non-market apps on the PC. Between Google's restore of market apps and Ti-Bu, anyone can be up and running the way they were within one hour. Sucks but there it is.
Hello!
I tried to update my phone (SM-G975U) via Odin from Android 9 to Android 12, got the firmware from SamFw.com. Everything went fine until the phone rebooted, after unlocking the phone gets stuck on 'phone is starting'. I CAN access the Set Up Menu, Uninstall apps, move some settings here and there, connect to Wifi/Bluetooth, receive calls, install apps using ADB. Also, theres a notification all the time that reads 'Phone restarted Unlock your phone to get app notifications', I'm assuming that the phone thinks it is not unlocked and that's why it doesn't fully boot up.
Some things that I've already tried:
Intalling another Launcher (Pixel Launcher)
Reinstalling the firmware (ver G975USQU6IVC7) / Trying with different CSC with no results
Wiping Cache in Recovery Mode
Deleting/Adding Fingerprints
Changing from Lock Pattern to NIP to Password
I don't really want to do the full wipe, I would like to keep my data or be able to export the photos (Device not Recognized by Smart Switch also)
Is there anything else I can do?, has anyone been through the same issue?
Is your phone rooted?
Vatt`ghern said:
Is your phone rooted?
Click to expand...
Click to collapse
No, it's not rooted
Hi !
@DannOsnaya have you found a solution to the phone problem other than restoring to factory settings?
I have the same problem at the moment, almost identical to what you experienced.
If anyone has some advice on how to fix this problem, please share your advice.
My phone is not rooted.
Racer512 said:
Hi !
@DannOsnaya have you found a solution to the phone problem other than restoring to factory settings?
I have the same problem at the moment, almost identical to what you experienced.
If anyone has some advice on how to fix this problem, please share your advice.
My phone is not rooted.
Click to expand...
Click to collapse
Sadly, I have not
My phone is still like that, I tried updating to the newest security patch but didn't work either, haven't lost hope in avoiding factory reset tho
Hi. Did u find any solution to it. Am facing the same issue. Although I tried to factory reset but doesn't work.
DannOsnaya said:
Sadly, I have not
My phone is still like that, I tried updating to the newest security patch but didn't work either, haven't lost hope in avoiding factory reset tho
Click to expand...
Click to collapse
Any way to factory reset. I tried every possible way following YouTube but nothing works. It's just stuck. I've a backup of my data so not worried.
No, I still have the same issue.
Have you tried to install a launcher?
DannOsnaya said:
No, I still have the same issue.
Have you tried to install a launcher?
Click to expand...
Click to collapse
Nothing works. Now decided to show it to anyone. I guess the mobile shops have an option to erase everything. I don't understand how did it happen because it's usually with my toddler, he might have done something.
DannOsnaya said:
Hello!
I tried to update my phone (SM-G975U) via Odin from Android 9 to Android 12, got the firmware from SamFw.com. Everything went fine until the phone rebooted, after unlocking the phone gets stuck on 'phone is starting'. I CAN access the Set Up Menu, Uninstall apps, move some settings here and there, connect to Wifi/Bluetooth, receive calls, install apps using ADB. Also, theres a notification all the time that reads 'Phone restarted Unlock your phone to get app notifications', I'm assuming that the phone thinks it is not unlocked and that's why it doesn't fully boot up.
Some things that I've already tried:
Intalling another Launcher (Pixel Launcher)
Reinstalling the firmware (ver G975USQU6IVC7) / Trying with different CSC with no results
Wiping Cache in Recovery Mode
Deleting/Adding Fingerprints
Changing from Lock Pattern to NIP to Password
I don't really want to do the full wipe, I would like to keep my data or be able to export the photos (Device not Recognized by Smart Switch also)
Is there anything else I can do?, has anyone been through the same issue?
Click to expand...
Click to collapse
I followed a video and wiped out. Finally successful. I wasn't worried about data as Google has a backup.
I followed this method and finally it's factory reset.