Hi, I have a prophet two days ago. I'm looking if I find the MAC address of the device to add it to my WiFi Router filter. How could I know this? I can't find it.
Don't worry I already found it. For those newbies like me here it is:
Turn wifi on, then in Com Mgr go to Menu, Wifi Settings. The Mac address is on the Advanced tab
Hi, I have HTC Touch HD New. I have home wireless secured router DHCP with (WPA2 Mixed) with paraphrase While trying to connect I ran through wizard to connect to my wireless no luck. Then gave static IP , changed WPA2 to WPA/TKP, changed channel from 5 to 11 no response, stopped Firewall, anything what can be done with router did…..no connection. The HD sees the network, but refuse to connect. Although, I am able to connect to an unsecured networks. All other media that connected to my wireless network works fine. Also I have noticed that wile running wizard the: "Use IEE8021x network access control" is checked and gray so I am unable to uncheck it. Maybe here is the problem.. no clue. Appreciate any suggestion.
Hi,
I can confirm I have the same problem.
Not only with Touch HD but also with HTC Rapheal.
If I find a solution I will let you know.
I had this problem too. In the wizard you have to specify it as a 'worknetwork', not 'internet'. The 'internet' option is for public (secured) networks like on a café. Then again, maybe you did this already. I have a WEP encryption.
You might also want to check, if your HD connects at all by turning off encryption in your WLAN router.
If your HD connects fine, then check in Advanced Config under the "Network" section, if you have WPA authentication enabled. My ROM had this disabled. After I enabled this option and made a soft-reset, my HD could connect to my WPA2(AES) secured network.
If everything else fails, you might try this free supplicant: http://www.securew2.com/products/
Please, report back if and how you resolved the problem !
None of the sugestions here (post #3, #4 and #5) solved my problem.
It's still not possible to connect to a secured network.
Tried without MAC filtering and vissible network but no joy.
I use WPA-PSK with a network key.
Unsecured it connects fine.
spasovxda said:
If everything else fails, you might try this free supplicant: http://www.securew2.com/products/
Please, report back if and how you resolved the problem !
Click to expand...
Click to collapse
I had the same problem with my Linksys Wrt54g Router using WPA-PSK, no matter what I tried it just would not connect. Without encryption or WEP encryption it worked just fine. Did set Wifi to performance oriented on the HD since that seems to have helped others but still no success.....
Here's the rub: I had installed Schaps Advanced Config tool before and had enabled WPA authentication under network. In a last attempt I set WPA Auth. to disabled, did a soft reset.....activated Wifi, entered my (27 character) passphrase and...my HD connects to my router using WPA-PSK and MAC-filtering without a problem...so that might be worth checking as well...
i hav no problem conneting my blackstone to my linksys wrt610 router using wpa2-aes. maybe you hav ur mac adres filtering turned on
just my 2 cents
Ditto post #8..
I have just connected for the first time to my work network, WPA-PSK(AES) and it connected fine without any problems.
Switched on CM, waited for the phone to list the networks, selected the one I needed and then choose "work" for connection and entered our passphrase. Sync'd up without a hitch.
Just to put this out there - do not connect your phone to the pc when trying to go wifi. It is disabled when activsync is... active.
Hi,
Thanks for the help.
Yes MAC filter is enabled but I've added the adress of HD to the list so it should work.
Today I've changed the channel in my Zyxel router to channel 11 and ques what....
IT WORKS FINALLY !
Channel 11 I choose because that's what the Touch HD chooses in WLan settings.
Maybe this helps for other people as well.
Edit;
A small update to mention.
I have two devices here, Touch Pro and Touch HD.
They both connect fine now.
Also the Touch Pro seems to pick channel 11 as default channel !
I would love to see someone confirms this because it was a real bugger to me.
Edit 2;
With MAC filter enabled both devices won't connect.
Weird thing is, both devices have the same MAC adres !
playboy4u2nv said:
i hav no problem conneting my blackstone to my linksys wrt610 router using wpa2-aes. maybe you hav ur mac adres filtering turned on
just my 2 cents
Click to expand...
Click to collapse
Laurentius26 said:
...Weird thing is, both devices have the same MAC adres !
Click to expand...
Click to collapse
Are you sure you're seeing it correctly??? MAC addresses are unique, just as telephone numbers are unique to the phone system. Same concept. No two wifi devices are supposed to have the same mac address...
I was having the same issue: not being able to connect my HD to my wireless network. Very frustrating... Then I remembered I use a controlled Access List, on my wireless router, based on MAC addresses. Once I put my HD's MAC in the list, I was able to connect.
I made a mistake.
I connected both devices to the desktop with Active sync to find out MAC.
If I give the command 'IPCONFIG /ALL' both WM devices have the same physical adress,
but after I succesfull made a wifi connection (without MAC filter) with both devices,
I noticed that the MAC adresses are different on both devices in the router config window.
I've added both adresses to MAC filter and enable.
Now everything is up and running !
JesseW said:
Are you sure you're seeing it correctly??? MAC addresses are unique, just as telephone numbers are unique to the phone system. Same concept. No two wifi devices are supposed to have the same mac address...
I was having the same issue: not being able to connect my HD to my wireless network. Very frustrating... Then I remembered I use a controlled Access List, on my wireless router, based on MAC addresses. Once I put my HD's MAC in the list, I was able to connect.
Click to expand...
Click to collapse
Laurentius26 said:
Channel 11 I choose because that's what the Touch HD chooses in WLan settings.
Click to expand...
Click to collapse
Can this be changed on the Touch HD? I don't seem to be able to change it. And channel 11 is a bit oversubscribed where I am...
razorblader said:
I had the same problem with my Linksys Wrt54g Router using WPA-PSK, no matter what I tried it just would not connect. Without encryption or WEP encryption it worked just fine. Did set Wifi to performance oriented on the HD since that seems to have helped others but still no success.....
Here's the rub: I had installed Schaps Advanced Config tool before and had enabled WPA authentication under network. In a last attempt I set WPA Auth. to disabled, did a soft reset.....activated Wifi, entered my (27 character) passphrase and...my HD connects to my router using WPA-PSK and MAC-filtering without a problem...so that might be worth checking as well...
Click to expand...
Click to collapse
i had the same problem. my hd use to connect fine with my wireless ruter untill yesterday. everything i tryed failed until i red this solution. i've done what razorblader suggested and guess what. it works flawless.
thank you!
it seems that the problem occurs after instaling advanced config 3.3, wich i did yesterday. for some reason it seems it mess the wifi settings.
thanks again!
i still have another problem, wich i have it since i bought the hd
i connect my laptop to my wifi router and it works great. i connect my hd to my wifi router and it works (again) great
but if i connect my hd to my laptop via usb and activesync, my laptop lose wifi connection. i reconnect it, keeps connection for few seconds and it loose it again.
any advice?
thank you!
Confirmed...
Had the same problem, Advanced Config WPA disabled works like a charm, if you enable it it actually disables it...
I connect to a Linksys broadband router with Mac filtering and WEP with no problems. Too lazy to try WPA2 because I'll have to reconfigure 3 PC's and two wireless printers. If I do try WPA(2), I post here.
I have WPA2-PSK with mac filtering and ssid broadcasting disabled. And I never had any problems, my router is linksys wag200 if it matters. Maybe you just do something wrong?
Wi-Fi and Active Sync
noris08 said:
i still have another problem, wich i have it since i bought the hd
i connect my laptop to my wifi router and it works great. i connect my hd to my wifi router and it works (again) great
but if i connect my hd to my laptop via usb and activesync, my laptop lose wifi connection. i reconnect it, keeps connection for few seconds and it loose it again.
any advice?
thank you!
Click to expand...
Click to collapse
Note: This may be in a slightly different place in ActiveSync on XP.
I have Windows Mobile Device Center on Vista and I had the same trouble until I went to Mobile Device Settings > Connection Settings > check "Allow data connections on device when connected to PC"
(see attachment)
Just noticed you said laptop loses wi-fi.... I assumed HD loses wi-fi. My bad.
This may or may not help some of you, but I found out (the hard way) that the WLAN pre-shared key "passphrase" may only be 12 bytes long. Any more and it will not work.
-Valynor
Hi,
I have an HTC Elfin that has no problem connecting to a home network with WEP encryption. But at work, I cannot connect to the network with WPA-TKIP encryption. My phone just tries to connect for a few seconds and then the status of the access point goes back to "available". I've verified the network pass phrase, as it does work with my co-worker's netbook. What is the problem here?
BTW, I've been reading up on this problem and somebody mentioned the fix of turning on/off the wifi (turn on wifi, connect, turn off wifi and then on again), but it doesn't work for me:
http://forum.xda-developers.com/showthread.php?t=327928
dtran707 said:
Hi,
I have an HTC Elfin that has no problem connecting to a home network with WEP encryption. But at work, I cannot connect to the network with WPA-TKIP encryption. My phone just tries to connect for a few seconds and then the status of the access point goes back to "available". I've verified the network pass phrase, as it does work with my co-worker's netbook. What is the problem here?
BTW, I've been reading up on this problem and somebody mentioned the fix of turning on/off the wifi (turn on wifi, connect, turn off wifi and then on again), but it doesn't work for me:
http://forum.xda-developers.com/showthread.php?t=327928
Click to expand...
Click to collapse
Try to set wifi to best performance instead of best battery first.
Often the problem is also caused by a combination of the router (brand/type) and a Windows based device/computer.
Some things you can try to get a working connection with WPA-PSK enabled:
1. Modify the registry:
\HKLM\Comm\EAP\Extension\25\ValidateServerCert=dword:00000000
2. Modify the network settings:
Settings > Connections (tab) > Wi-Fi > Network Adapters (Tab)
and select "NE2000 Compatible Ethernet Driver" (maybe you have to config a static ip-address).
Thanks for the suggestions. I did all those, except for the static IP since our network admin doesn't provide one. It still doesn't work. One thing I'd like to understand is that in my case, why does the WPA-PSK connection work for the standard Windows environment (laptop/netbook, desktop) but not Windows Mobile? What could be the difference?
I don´t know what ROM are you using, but if it is some of 23XXX Builds, disconnect first the Bluetooth and then connect the Wireless... Should work now...
My ROM is MK_872_05 WWE, from chota_shivaji. It uses WM6.5 CE OS 5.2.21872. Thanks for your suggestion. I will try it out on Monday when I get back to work.
I disconnected the Bluetooth connection and tried again to the WPA-PSK encrypted access point at work and it still doesn't work. Just yesterday at a relative's place, I was able to connect to his router with WPA security. I think there's something different with the one at work which does not work with Winmo devices.
at work do u just have a password or a user/password? are u using certificates?
At work I have a guest username and password that I can use to log in for the WIFI access point. The password changes every week, but I confirmed that I used the latest one. But I don't think there's a certificate needed since my co-worker is able to use his home netbook to log in without anything else except the same username and password.
Hi guys ..
How can i set a static ip in WP7 on HD2 ??
currently not possible
holy crap thanks for the reminder! as i kept thinking something was missing.
iphones (no matter how simple) could do it, and here I was thinking Microsoft is the king of networking....
Actually if you really want static IP, you can "push" to it. If you find out your wlan MAC address, use your router to assign only the IP which you select.
To find out your MAC address is simple: connect your phone to wifi, connect to router and see n the logs (even the dumiest routers keeps logs of what wifi cards are connected to it)
Just a small idea....
Rgs, Seba
Yeah my router thinks there are 5 mac addresses logged onto its wifi, but each time wp7 has reset its created a new mac.
Hello, I have problem with mac randomization. My phone no change mac for networs wifi.
It has a different address assigned to different networks and cannot be changed for a given network. Does anyone know how to make it change?
@edit
Ok, solved, in programing option enable option wifi.