At wi-fi 4 i have only 144 mbps with mimo 2x2 (2x72 mbps). How to unlock 40 mhz bandwith?
I install this module: github.com/Magisk-Modules-Repo/wifi-bonding
but it din't work. I change .ini file manually - nothing happends
I just want 300 mbps at 2.4 wi-fi
Related
Hi guys,
I've got a mobile with EDGE/HSCSD...
My question is (Sorry but I don't know nothing about speed and irda and EGDE/HSCSD.):
if I use mobile like HSCSD modem for my laptop and I use irda as connection from bobile to laptop... is it okay using HSCSD over irda or the irda speed is too slow?
irda is 115.2 kbps.
HSCSD is 43.2 kbps (sometimes a bit more, depends on network)
EDGE is theoretically 384 kbps but I don't think there is any network (or mobile) allowing such speeds. Usually it's around 100 kbps.
So it should be no problem using irda for your connections!
I've seen that the Atrix does indeed support it... Has anyone done speedtests with it?
I connected to my 5Ghz network at home, but it wouldn't connect to the net.
CrunchyToast said:
I connected to my 5Ghz network at home, but it wouldn't connect to the net.
Click to expand...
Click to collapse
My 5Ghz works but the reception is not very good. I may say, it's bad.
i am able to pull an average 40 Mbps of my 55 Mbps connection and upload 8 Mbps of an 8 Mbps connection on my new atrix
9.33 Mbps
1.47 Mbps
Server is ~920 miles
on my wifi, 5ghz pulls 20828 kbps down 8343 kbps up
using the 2.4ghz on my same network pulls 8024 kbps down and 1730 kbps up to the same server
Thanks for the replies Have you guys tried pushing a file to te phone with an FTP client with 5ghz?
hello guys,
i recently bought a new router tp link (td-w8960n) that supports 300 Mbps connection rate. as far as i know nexus 4 supports Wi-Fi 802.11 n dual-band, that supposed to be 300mbps.
when i connect to the network (with and without wifi optimizations) the connection rate is 72mbps reported by the device.i have full signal (about -50 to -60 dBm) and the router about 1 meter from the phone without anything in between. the network is broadcasting in 2.4 GHz and channel 13 without any interference from other networks on the same channel.
my question is why can't i connect to a higher rate? at least i should be connected at 150 Mbps. this is very strange to me.
Hi!
I have very slow file transfer from phone to PC - only 100 kB/s.
When I transfer file from router to PC speed is normal - about 2,5 MB/s or 5,5 MB/s (depend of Wi-Fi router 802.11 n or g).
In both cases file transfer is initiated on phone in ES File Explorer with sftp connection.
Can I speed up this 100 kB/s or this is normal (limitation in uplink speed or something similar)?
Regards,
Mlaky
I tried the Wifi Bonding (Qualcomm) mod created by simonsmh to enable 40mhz on 2.4ghz mode. However it did not work. The mod is installed but without any positive results.
On my phone, I am still connecting to my home wifi @ 72mbps only while my other clients are connecting at 270-300mbps link speeds!
Any clues guys?
shobhitk said:
I tried the Wifi Bonding (Qualcomm) mod created by simonsmh to enable 40mhz on 2.4ghz mode. However it did not work. The mod is installed but without any positive results.
On my phone, I am still connecting to my home wifi @ 72mbps only while my other clients are connecting at 270-300mbps link speeds!
Any clues guys?
Click to expand...
Click to collapse
Same problem on my Redmi Note 3 Pro (Kenzo). Work's on 5GHz but not on 2.4GHz.
Enable 40 MHz option in the width range of router 2.4 GHz or choose the maximum width of your router in 2.4GHz option , you are set to go and restart your device and router !!