I tried the Wifi Bonding (Qualcomm) mod created by simonsmh to enable 40mhz on 2.4ghz mode. However it did not work. The mod is installed but without any positive results.
On my phone, I am still connecting to my home wifi @ 72mbps only while my other clients are connecting at 270-300mbps link speeds!
Any clues guys?
shobhitk said:
I tried the Wifi Bonding (Qualcomm) mod created by simonsmh to enable 40mhz on 2.4ghz mode. However it did not work. The mod is installed but without any positive results.
On my phone, I am still connecting to my home wifi @ 72mbps only while my other clients are connecting at 270-300mbps link speeds!
Any clues guys?
Click to expand...
Click to collapse
Same problem on my Redmi Note 3 Pro (Kenzo). Work's on 5GHz but not on 2.4GHz.
Enable 40 MHz option in the width range of router 2.4 GHz or choose the maximum width of your router in 2.4GHz option , you are set to go and restart your device and router !!
Related
Hi ,
i dont know if this requires a new topic, but havent seen much on this. but has anyone been able to connect to wireless N Speed with Froyo?? i check my router stats and it still says my nexus is connected to G at 54mbps.. I have a Mac that connects fine to it in N Mode. anybody else been able to connect at those speeds?? or was this not included in the froyo update??
Cheers,
Dan
already in 2.1
Well I have connected as N and speed 65mbps...but then again I had that already in 2.1.
If I look in my d-link dir-655, it says that I'm using N-version in both android versions.
I tried with speed test I came up to downlink 16.44mbps uplink 4.24mbps with 2.2 and with 2.1 max speed was down 18.92mbps and up 2.21mbps.
hmmm... is there a specific channel ur using maybe? :S
im using a Dlink DIR -615.. its only a 2.4ghz, no the 5ghz N'
Here is a copy&paste from my router
Wireless Network Settings (Wireless manual settings)
Wireless Radio : Enabled (Always)
802.11 Mode : Mixed 802.11n, 802.11g and 802.11b
Enable Auto Channel Scan : On
Wireless Channel : 2.437 Ghz - Channel 6 (grayed out because its on automatic)
Transmission Rate : Best (automatic)
Channel Width : Auto 20/40 Mhz
Wireless LAN (Status information)
Wireless Radio : Enabled
802.11 Mode : Mixed 802.11n, 802.11g and 802.11b
Channel Width : 40MHz
Channel : 1
Secondary Channel : 5
WISH : Active
Wi-Fi Protected Setup : Enabled/Configured
mmm, yeah my settings are the same...
is there anything on the Nexus needed to be changed or enabled?
i cant understand why it wont connect..
i might try force N only connects on my router,
Hi,
I have a UK Desire Z. The spec says the phone is capable of connecting to b/g/n wifi standards. However I am having trouble seeing my N network on the wireless list. Has anyone sucessfully connected thier phone to an N network?
Are you trying to connect to a 2.4hgz network or a 5ghz one?
It should work on the 2,4 but not on the 5 ghz
I have dual-band router and Desire Z does see/connect to 2.4GHz N network. It does not see 5GHz network. But my 5GHz is running in two channel 40MHz mode, didn't have time to check if switching to single channel would allow Z to connect.
Mine connects fine to my home Wi-Fi network, which is 'N' standard. Not sure what speed it is connecting at, or whether it's dropping back to B/G though.
Do you have MAC address security blocking set on your router, and if so have you told it about the phone's MAC address?
Andre
buzmay said:
Are you trying to connect to a 2.4hgz network or a 5ghz one?
It should work on the 2,4 but not on the 5 ghz
Click to expand...
Click to collapse
This is the answer to the thread.
schriss said:
I have dual-band router and Desire Z does see/connect to 2.4GHz N network. It does not see 5GHz network. But my 5GHz is running in two channel 40MHz mode, didn't have time to check if switching to single channel would allow Z to connect.
Click to expand...
Click to collapse
This verifies that answer, changing to single channel on 5GHz will not make a difference.
The wifi radio on the DZ is a 2.4GHz radio.
So I just set my routers wifi mode to 300Mbps @ 2.4Ghz and immediately was not able to connect to my wifi. I dropped the mode down to 145Mbps, same frequency, and right away was able to connect. What gives?
onishchuk4 said:
So I just set my routers wifi mode to 300Mbps @ 2.4Ghz and immediately was not able to connect to my wifi. I dropped the mode down to 145Mbps, same frequency, and right away was able to connect. What gives?
Click to expand...
Click to collapse
I'm not networking expert but i believe it's the b/g/n radio that you are using. IIRC the faster setting requires the n radio. Does you phone & ROM support n?
If i am wrong someone please correct me.
My router is dual band and i want to say it connects to 5ghz and connects as a n connection. some roms do not have the n drivers. I too could be wrong.
tw39515 said:
My router is dual band and i want to say it connects to 5ghz and connects as a n connection. some roms do not have the n drivers. I too could be wrong.
Click to expand...
Click to collapse
You're probably right. I'm using CM7.1.
I have tried connecting my tablet to a wirless N connection but it doesnt pick it up. Anybody have this problem or know how to connect to a wireless N connection on the tablet?
sakobatoneko said:
I have tried connecting my tablet to a wirless N connection but it doesnt pick it up. Anybody have this problem or know how to connect to a wireless N connection on the tablet?
Click to expand...
Click to collapse
I haven't tried it, but I believe it'll only work if the Wireless N Network is the 2.4GHz mode. The specs for the TPT say it is compatible with b/g/n, since a isn't supported the 5GHz spectrum cannot be supported.
If your router is simultaneous dual-band, meaning, it can transmit a 2.4GHz and a 5GHz network at the same time then you shouldn't have any issues. If the router is only dual-band and not simultaneous then you'll have to fall back on the 2.4GHz spectrum.
Hope this helps.
Oh, ok. The router was transmitting in 5ghz; changing it to 2.4 worked.Thanks
Do you guys know how to solve this problem. Can't even see my 2.4Ghz wireless network. Can only see 5Ghz wireless network. Any suggestion ?
Reboot your router
Change the 2.4GHz Wireless channel on the router
Clear caches from recovery on the phone - can other devices see the 2.4GHz network? -
Disable the 5GHz network and see if it can connect to 2.4GHz then...
Can your router push out both 2.4GHz and 5GHz simultaneously?
Disable Smart Network Switch on the phone in WiFi Settings
thanks for your reply.
Yeah, Other devices can see 2.4Ghz and 5Ghz. Yes. I'm using RT-N66U so both 2.4 and 5GHz are available.
If my router was problem other devices cannot connect so, is not my router.
Following are done.
-Rebooted s 5 many times.
-Did hard reset/wipe cache
-smart network is disabled. ( Don't even put SIM card yet)
Phone is not ROOTED.
Suggestions?
Factory reset the phone?
Yes Factory reset and Hard reset is done but nothing change
Go to someone elses house who has 2.4GHz WiFi and see if your S5 can connect, then you'll know if it is a fault with the phone, or your router
My router have only 2.4 GHz but not problem with other devices.
My neighbor have both 2.4 and 5 GHz when we try to connect it's only show 5GHz band. Not 2.4. btw i'm running Lollipop 5.0