Hello,
I really need assistance to unbrick my hard bricked SM-G950U. I need either the service rom (fastboot rom) to flash with QFIL or the SDC repair image for SD card rescue (usually created by Atf box). My phone is hardbricked, it shows "qualcomm hs-usb qdloader 9008" when plugged into pc and it is in fact unresponsive. Please help me.
Thank you.
Hi I just wanted to give this thread a bump... see if there is an official/ unofficial unbrick process for this device... I've read upon the qualcomm unbrick process.. and still have no luck.. if anybody has successfully unbridled their s8.. please pm or as how me some light at the end of this dark and lonely tunnel... Thank you.
Same
dkns1 said:
Hi I just wanted to give this thread a bump... see if there is an official/ unofficial unbrick process for this device... I've read upon the qualcomm unbrick process.. and still have no luck.. if anybody has successfully unbridled their s8.. please pm or as how me some light at the end of this dark and lonely tunnel... Thank you.
Click to expand...
Click to collapse
I'm in the same boat, but it's my wife's S8. Blackscreened while on the charger about an hour after the 8.0 OTA was applied.
dkns1 said:
Hi I just wanted to give this thread a bump... see if there is an official/ unofficial unbrick process for this device... I've read upon the qualcomm unbrick process.. and still have no luck.. if anybody has successfully unbridled their s8.. please pm or as how me some light at the end of this dark and lonely tunnel... Thank you.
Click to expand...
Click to collapse
Westen81 said:
I'm in the same boat, but it's my wife's S8. Blackscreened while on the charger about an hour after the 8.0 OTA was applied.
Click to expand...
Click to collapse
I can confirm there is a edl brick fix. Its up to the man thought if he wants to or has it for release...
@ elliwigy
TheMadScientist said:
I can confirm there is a edl brick fix. Its up to the man thought if he wants to or has it for release...
@ elliwigy
Click to expand...
Click to collapse
The files he currently has are for the S8+, he lost a lot of the stuff he had for other devices in a HDD failure. Still looking for a current FireHose programmer, RawProgram, and Patch files for MSM8998 on the Galaxy S8. If *anybody* has any hints even on where I can get a valid, current set of QFIL files for the SM-G950U, that would be great! If I can get the files and it works, I'll share the version of QPST/QFIL I'm using, etc. on here!
Edit: also, I've been using a USB 3.0 port on the front header with my attempts. My next go at it, I'm going to try one of the 2.0 ports on the back.
I will look back and speak with him. I helped test some edl and first tests where for a 955 so I may still have them myself.
Westen81 said:
The files he currently has are for the S8+, he lost a lot of the stuff he had for other devices in a HDD failure. Still looking for a current FireHose programmer, RawProgram, and Patch files for MSM8998 on the Galaxy S8. If *anybody* has any hints even on where I can get a valid, current set of QFIL files for the SM-G950U, that would be great! If I can get the files and it works, I'll share the version of QPST/QFIL I'm using, etc. on here!
Edit: also, I've been using a USB 3.0 port on the front header with my attempts. My next go at it, I'm going to try one of the 2.0 ports on the back.
Click to expand...
Click to collapse
Are you s8? I have the edl fix for s8 but I have to clear it with him first as they where for testing I have used them. My self. I may have edl recovery for 8+ but I know I got the reg s8s. Keep em put up like gold. Lol
thehaXor said:
Hello,
I really need assistance to unbrick my hard bricked SM-G950U. I need either the service rom (fastboot rom) to flash with QFIL or the SDC repair image for SD card rescue (usually created by Atf box). My phone is hardbricked, it shows "qualcomm hs-usb qdloader 9008" when plugged into pc and it is in fact unresponsive. Please help me.
Thank you.
Click to expand...
Click to collapse
dkns1 said:
Hi I just wanted to give this thread a bump... see if there is an official/ unofficial unbrick process for this device... I've read upon the qualcomm unbrick process.. and still have no luck.. if anybody has successfully unbridled their s8.. please pm or as how me some light at the end of this dark and lonely tunnel... Thank you.
Click to expand...
Click to collapse
Westen81 said:
I'm in the same boat, but it's my wife's S8. Blackscreened while on the charger about an hour after the 8.0 OTA was applied.
Click to expand...
Click to collapse
Ok guys I got the go ahead I have the edl files I can help you guys possibly these are not my work but we can make a telegram chat and we can see if we can get some life back to you guys:good::good::good:
TheMadScientist said:
Are you s8? I have the edl fix for s8 but I have to clear it with him first as they where for testing I have used them. My self. I may have edl recovery for 8+ but I know I got the reg s8s. Keep em put up like gold. Lol
Click to expand...
Click to collapse
Yes, it is a T-Mobile US Galaxy S8 (SM-G950U). I was talking to him in Hangouts the other day when I was trying with the files I do have, he was trying to EDL flash a tablet he has later that day. Thanks for the reply, man!
So here is my log from the most recent attempt:
Validating Application Configuration
Load APP Configuration
COM:-1
SAHARA:True
SAHARA:C:\Users\sacre\Downloads\G950U2\prog_ufs_firehose_8998_ddr.elf
SEARCHPATH:C:\Users\sacre\Downloads\G950U2
RAWPROGRAM:
rawprogram3.xml
PATCH:
patch3.xml
ACKRAWDATAEVERYNUMPACKETS:False
ACKRAWDATAEVERYNUMPACKETS:100
MAXPAYLOADSIZETOTARGETINBYTES:False
MAXPAYLOADSIZETOTARGETINBYTES:49152
DEVICETYPE:UFS
PLATFORM:8x26
VALIDATIONMODE:0
RESETAFTERDOWNLOAD:True
MAXDIGESTTABLESIZE:8192
SWITCHTOFIREHOSETIMEOUT:30
RESETTIMEOUT:200
RESETDELAYTIME:2
FLATBUILDPATH:C:\
FLATBUILDFORCEOVERRIDE:True
QCNPATH:C:\Temp\00000000.qcn
QCNAUTOBACKUPRESTORE:False
SPCCODE:000000
ENABLEMULTISIM:False
PROVISIONPROGRAMMERPATH:C:\Users\sacre\Downloads\G950U2\prog_ufs_firehose_8998_ddr.elf
PROVISIONXMLPATH:C:\Users\sacre\Downloads\G950U2\provision_samsung.xml
Load ARG Configuration
Validating Download Configuration
Image Search Path: C:\Users\sacre\Downloads\G950U2
RAWPROGRAM file path: C:\Users\sacre\Downloads\G950U2\rawprogram3.xml
PATCH file path:C:\Users\sacre\Downloads\G950U2\patch3.xml
Programmer Path:C:\Users\sacre\Downloads\G950U2\prog_ufs_firehose_8998_ddr.elf
Process Index:0
Image Search Path: C:\Users\sacre\Downloads\G950U2
RAWPROGRAM file path: C:\Users\sacre\Downloads\G950U2\rawprogram0.xml
PATCH file path:C:\Users\sacre\Downloads\G950U2\patch0.xml
Start Download
Program Path:C:\Users\sacre\Downloads\G950U2\prog_ufs_firehose_8998_ddr.elf
Binary build date: May 13 2015 @ 14:41:37
QSAHARASERVER CALLED LIKE THIS: 'C:\Program Files (x86)\Qualcomm\QPST\bin\QSaharaServer.exe -p \\.\COM4 -s 13:C:\Users\sacre\Downloads\G950U2\prog_ufs_firehose_8998_ddr.elf 'Current working dir: C:\Users\sacre\AppData\Roaming\Qualcomm\QFIL
Sahara mappings:
2: amss.mbn
6: apps.mbn
8: dsp1.mbn
10: dbl.mbn
11: osbl.mbn
12: dsp2.mbn
16: efs1.mbn
17: efs2.mbn
20: efs3.mbn
21: sbl1.mbn
22: sbl2.mbn
23: rpm.mbn
25: tz.mbn
28: dsp3.mbn
29: acdb.mbn
30: wdt.mbn
31: mba.mbn
13: C:\Users\sacre\Downloads\G950U2\prog_ufs_firehose_8998_ddr.elf
02:47:47: Requested ID 13, file: "C:\Users\sacre\Downloads\G950U2\prog_ufs_firehose_8998_ddr.elf"
02:47:47: 600504 bytes transferred in 0.172000 seconds (3.3296MBps)
02:47:47: File transferred successfully
02:47:47: Sahara protocol completed
Sending Programmer Finished
Switch To FireHose
Wait for 3 seconds...
Max Payload Size to Target:49152 Bytes
Device Type:UFS
Platform:8x26
Disable Ack Raw Data Every N Packets
Skip Write:False
Always Validate:False
Use Verbose:False
Binary build date: Jun 3 2015 @ 17:12:06
Build version: 15.06. 3.17.12.06
02:47:51: INFO: FH_LOADER WAS CALLED EXACTLY LIKE THIS
************************************************
C:\Program Files (x86)\Qualcomm\QPST\bin\fh_loader.exe --port=\\.\COM4 --sendxml=rawprogram0.xml --search_path=C:\Users\sacre\Downloads\G950U2 --noprompt --showpercentagecomplete --zlpawarehost=1 --memoryname=UFS
************************************************
02:47:51: INFO: Current working dir (cwd): C:\Users\sacre\AppData\Roaming\Qualcomm\QFIL\
02:47:51: INFO: Showing network mappings to allow debugging
02:47:51: INFO:
02:47:51: INFO: Trying to store 'rawprogram0.xml' in string table
02:47:51: INFO: Looking for file 'rawprogram0.xml'
02:47:51: INFO: User wants to talk to port '\\.\COM4'
02:47:51: INFO: Took 0.00000000 seconds to open port
02:47:51: INFO: Sorting TAGS to ensure order is <configure>,<erase>, others, <patch>,<power>
02:47:51: INFO: If you don't want this, use --dontsorttags
02:47:51: INFO: Looking for file 'gpt_main0.bin'
02:47:51: INFO: Looking for file 'gpt_backup0.bin'
02:47:51: INFO:
Total to be tansferd with <program> or <read> is 44.00 KB
02:47:51: INFO: Sending <configure>
02:47:51: INFO: TARGET SAID: 'Binary build date: Jan 2 2018 @ 13:14:45'
02:47:51: INFO: TARGET SAID: 'Chip serial num: 4294967295 (0xffffffff)'
02:47:51: INFO: TARGET SAID: 'Supported Functions: program configure nop firmwarewrite patch setbootablestoragedrive ufs emmc power benchmark read getstorageinfo getsha256digest erase peek poke '
02:47:51: INFO: TARGET SAID: 'Calling usb_al_bulk_set_zlp_mode(TRUE) since ZlpAwareHost='1''
02:47:51: INFO: fh.attrs.MaxPayloadSizeToTargetInBytes = 1048576
02:47:51: INFO: fh.attrs.MaxPayloadSizeToTargetInBytesSupported = 1048576
02:47:51: INFO: In handleProgram('gpt_main0.bin')
02:47:51: INFO: Looking for file 'gpt_main0.bin'
02:47:51: INFO: =======================================================
02:47:51: INFO: {<program> FILE: 'C:\Users\sacre\Downloads\G950U2\gpt_main0.bin'}
02:47:51: INFO: {<program> (24.00 KB) 6 sectors needed at location 0 on LUN 0}
02:47:51: INFO: =======================================================
02:47:51: INFO: TARGET SAID: 'ERROR: Failed to initialize (open whole lun) UFS Device slot 0 partition 0'
02:47:51: INFO: TARGET SAID: 'ERROR: ufs_open_error_code 0 :: 0x114'
02:47:51: INFO: TARGET SAID: 'ERROR: last ufs_open_error_code 16 :: 0x114'
02:47:51: INFO: TARGET SAID: 'ERROR: Failed to open the device 3 slot 0 partition 0'
02:47:51: INFO: TARGET SAID: 'INFO: Device type 3, slot 0, partition 0, error 0'
02:47:51: INFO: TARGET SAID: 'WARN: Get Info failed to open 3 slot 0, partition 0, error 0'
02:47:51: INFO: TARGET SAID: 'storage_device_get_num_partition_sectors FAILED!'
02:47:51: INFO: TARGET SAID: 'parseSectorValue could not handle start_sector value'
_____
| ___|
| |__ _ __ _ __ ___ _ __
| __| '__| '__/ _ \| '__|
| |__| | | | | (_) | |
\____/_| |_| \___/|_|
02:47:51: {ERROR: program FAILED - Please see log}
Writing log to 'C:\Users\sacre\AppData\Roaming\Qualcomm\QFIL\port_trace.txt', might take a minute
Log is 'C:\Users\sacre\AppData\Roaming\Qualcomm\QFIL\port_trace.txt'
Download Fail:FireHose Fail FHLoader Failrocess fail
Finish Download
Com4 is the port in use, but there's a weird com port callout at the very beginning there. Also noticed it changed the RawProgram and Patch from 3 to 0. Damn software. Damn phone.
Westen81 said:
So here is my log from the most recent attempt:
Validating Application Configuration
Load APP Configuration
COM:-1
SAHARA:True
SAHARA:C:\Users\sacre\Downloads\G950U2\prog_ufs_firehose_8998_ddr.elf
SEARCHPATH:C:\Users\sacre\Downloads\G950U2
RAWPROGRAM:
rawprogram3.xml
PATCH:
patch3.xml
ACKRAWDATAEVERYNUMPACKETS:False
ACKRAWDATAEVERYNUMPACKETS:100
MAXPAYLOADSIZETOTARGETINBYTES:False
MAXPAYLOADSIZETOTARGETINBYTES:49152
DEVICETYPE:UFS
PLATFORM:8x26
VALIDATIONMODE:0
RESETAFTERDOWNLOAD:True
MAXDIGESTTABLESIZE:8192
SWITCHTOFIREHOSETIMEOUT:30
RESETTIMEOUT:200
RESETDELAYTIME:2
FLATBUILDPATH:C:\
FLATBUILDFORCEOVERRIDE:True
QCNPATH:C:\Temp\00000000.qcn
QCNAUTOBACKUPRESTORE:False
SPCCODE:000000
ENABLEMULTISIM:False
PROVISIONPROGRAMMERPATH:C:\Users\sacre\Downloads\G950U2\prog_ufs_firehose_8998_ddr.elf
PROVISIONXMLPATH:C:\Users\sacre\Downloads\G950U2\provision_samsung.xml
Load ARG Configuration
Validating Download Configuration
Image Search Path: C:\Users\sacre\Downloads\G950U2
RAWPROGRAM file path: C:\Users\sacre\Downloads\G950U2\rawprogram3.xml
PATCH file path:C:\Users\sacre\Downloads\G950U2\patch3.xml
Programmer Path:C:\Users\sacre\Downloads\G950U2\prog_ufs_firehose_8998_ddr.elf
Process Index:0
Image Search Path: C:\Users\sacre\Downloads\G950U2
RAWPROGRAM file path: C:\Users\sacre\Downloads\G950U2\rawprogram0.xml
PATCH file path:C:\Users\sacre\Downloads\G950U2\patch0.xml
Start Download
Program Path:C:\Users\sacre\Downloads\G950U2\prog_ufs_firehose_8998_ddr.elf
Binary build date: May 13 2015 @ 14:41:37
QSAHARASERVER CALLED LIKE THIS: 'C:\Program Files (x86)\Qualcomm\QPST\bin\QSaharaServer.exe -p \\.\COM4 -s 13:C:\Users\sacre\Downloads\G950U2\prog_ufs_firehose_8998_ddr.elf 'Current working dir: C:\Users\sacre\AppData\Roaming\Qualcomm\QFIL
Sahara mappings:
2: amss.mbn
6: apps.mbn
8: dsp1.mbn
10: dbl.mbn
11: osbl.mbn
12: dsp2.mbn
16: efs1.mbn
17: efs2.mbn
20: efs3.mbn
21: sbl1.mbn
22: sbl2.mbn
23: rpm.mbn
25: tz.mbn
28: dsp3.mbn
29: acdb.mbn
30: wdt.mbn
31: mba.mbn
13: C:\Users\sacre\Downloads\G950U2\prog_ufs_firehose_8998_ddr.elf
02:47:47: Requested ID 13, file: "C:\Users\sacre\Downloads\G950U2\prog_ufs_firehose_8998_ddr.elf"
02:47:47: 600504 bytes transferred in 0.172000 seconds (3.3296MBps)
02:47:47: File transferred successfully
02:47:47: Sahara protocol completed
Sending Programmer Finished
Switch To FireHose
Wait for 3 seconds...
Max Payload Size to Target:49152 Bytes
Device Type:UFS
Platform:8x26
Disable Ack Raw Data Every N Packets
Skip Write:False
Always Validate:False
Use Verbose:False
Binary build date: Jun 3 2015 @ 17:12:06
Build version: 15.06. 3.17.12.06
02:47:51: INFO: FH_LOADER WAS CALLED EXACTLY LIKE THIS
************************************************
C:\Program Files (x86)\Qualcomm\QPST\bin\fh_loader.exe --port=\\.\COM4 --sendxml=rawprogram0.xml --search_path=C:\Users\sacre\Downloads\G950U2 --noprompt --showpercentagecomplete --zlpawarehost=1 --memoryname=UFS
************************************************
02:47:51: INFO: Current working dir (cwd): C:\Users\sacre\AppData\Roaming\Qualcomm\QFIL\
02:47:51: INFO: Showing network mappings to allow debugging
02:47:51: INFO:
02:47:51: INFO: Trying to store 'rawprogram0.xml' in string table
02:47:51: INFO: Looking for file 'rawprogram0.xml'
02:47:51: INFO: User wants to talk to port '\\.\COM4'
02:47:51: INFO: Took 0.00000000 seconds to open port
02:47:51: INFO: Sorting TAGS to ensure order is <configure>,<erase>, others, <patch>,<power>
02:47:51: INFO: If you don't want this, use --dontsorttags
02:47:51: INFO: Looking for file 'gpt_main0.bin'
02:47:51: INFO: Looking for file 'gpt_backup0.bin'
02:47:51: INFO:
Total to be tansferd with <program> or <read> is 44.00 KB
02:47:51: INFO: Sending <configure>
02:47:51: INFO: TARGET SAID: 'Binary build date: Jan 2 2018 @ 13:14:45'
02:47:51: INFO: TARGET SAID: 'Chip serial num: 4294967295 (0xffffffff)'
02:47:51: INFO: TARGET SAID: 'Supported Functions: program configure nop firmwarewrite patch setbootablestoragedrive ufs emmc power benchmark read getstorageinfo getsha256digest erase peek poke '
02:47:51: INFO: TARGET SAID: 'Calling usb_al_bulk_set_zlp_mode(TRUE) since ZlpAwareHost='1''
02:47:51: INFO: fh.attrs.MaxPayloadSizeToTargetInBytes = 1048576
02:47:51: INFO: fh.attrs.MaxPayloadSizeToTargetInBytesSupported = 1048576
02:47:51: INFO: In handleProgram('gpt_main0.bin')
02:47:51: INFO: Looking for file 'gpt_main0.bin'
02:47:51: INFO: =======================================================
02:47:51: INFO: {<program> FILE: 'C:\Users\sacre\Downloads\G950U2\gpt_main0.bin'}
02:47:51: INFO: {<program> (24.00 KB) 6 sectors needed at location 0 on LUN 0}
02:47:51: INFO: =======================================================
02:47:51: INFO: TARGET SAID: 'ERROR: Failed to initialize (open whole lun) UFS Device slot 0 partition 0'
02:47:51: INFO: TARGET SAID: 'ERROR: ufs_open_error_code 0 :: 0x114'
02:47:51: INFO: TARGET SAID: 'ERROR: last ufs_open_error_code 16 :: 0x114'
02:47:51: INFO: TARGET SAID: 'ERROR: Failed to open the device 3 slot 0 partition 0'
02:47:51: INFO: TARGET SAID: 'INFO: Device type 3, slot 0, partition 0, error 0'
02:47:51: INFO: TARGET SAID: 'WARN: Get Info failed to open 3 slot 0, partition 0, error 0'
02:47:51: INFO: TARGET SAID: 'storage_device_get_num_partition_sectors FAILED!'
02:47:51: INFO: TARGET SAID: 'parseSectorValue could not handle start_sector value'
_____
| ___|
| |__ _ __ _ __ ___ _ __
| __| '__| '__/ _ \| '__|
| |__| | | | | (_) | |
\____/_| |_| \___/|_|
02:47:51: {ERROR: program FAILED - Please see log}
Writing log to 'C:\Users\sacre\AppData\Roaming\Qualcomm\QFIL\port_trace.txt', might take a minute
Log is 'C:\Users\sacre\AppData\Roaming\Qualcomm\QFIL\port_trace.txt'
Download Fail:FireHose Fail FHLoader Failrocess fail
Finish Download
Com4 is the port in use, but there's a weird com port callout at the very beginning there. Also noticed it changed the RawProgram and Patch from 3 to 0. Damn software. Damn phone.
Click to expand...
Click to collapse
Yea that's a lot different than what mine did. You are making it a lot farther. In qfil.
Like it's conflicting with it self. Hmmmmm. I show shoot. Few PM's this afternoon and see if any one can shed light on this one
TheMadScientist said:
Yea that's a lot different than what mine did. You are making it a lot farther. In qfil.
Like it's conflicting with it self. Hmmmmm. I show shoot. Few PM's this afternoon and see if any one can shed light on this one
Click to expand...
Click to collapse
W3RD. I even tweaked the port configuration settings in Windows for the 9008, as far as stop bits. left flow control off, set baud at 14.4 . If nobody has an epiphany between now and when I get off work, I'm gonna call it and tell the wife we're going to T-Mobile.
TheMadScientist said:
Ok guys I got the go ahead I have the edl files I can help you guys possibly these are not my work but we can make a telegram chat and we can see if we can get some life back to you guys:good::good::good:
Click to expand...
Click to collapse
Did you end up getting this figured out? I have 2 s8 G950u that have black screens after attempting to unlock with octoplus pro box. Any help would be appreciated.
amourer2 said:
Did you end up getting this figured out? I have 2 s8 G950u that have black screens after attempting to unlock with octoplus pro box. Any help would be appreciated.
Click to expand...
Click to collapse
hollar at me on hangouts and I can live chat you
https://hangouts.google.com/group/JyLSy4hFLPwGYx9g1
I will be on for the next few hours but you can hollar anytime ill respond back once i see it
I would love to get ahold of this S8 EDL fix if someone can part with the files. If you want them private I will keep them private. Trying to help someone with their bricked S8. Not my first EDL 9008 recovery but will be my first S8 so I can definitely use the practice. I could trade a carrier unlock or frp unlock job for the files if they are all intact and are for sure working. I have a few boxes I use for my phone repair work too.
Hi pros
I'm in kind of a similar situation....I think I flashed MY 950U PIE with wrong BL
This phone is dead....Doesn't boot...no download mode....No recovery mode....
When connected to pc....device manager Recognises device as QUALCOMM HS USB 9008
Any way to brig it back to life...?
Im a newbie in flashing if anybody has a solution.....step by step process will be hoghly appropriated
I've never bricked a phone. Installed JUI, and wanted to rollback to EUI via coolpad assistant. Couldn't do that because my PC wouldn't recognise my device, even though it did when flashing to JUI!
So I thought, why don't I flash a recovery via twrp - decided to flash recovery via miflash. Which was successful.
Now the phone doesn't switch on.
When a cable comes on, just two red lights flash.
I have tried to flash official firmware via YGDP and coolpad assistant. Phone is not recognised. uninstalled drivers and reinstalled them. To no avail. What do I do?
You can flash using QPST, I did that to unbrick my phone.
Extract the CPB and flash using QFIL.
But please do backup your phone internal before that. I fixed my brick but cant fix my baseband as I forgot to take a backup.
It would be a favor if anyone could send their QCN backed up ( in private message , be ensured that I will use my own imei number )
kassana69 said:
I've never bricked a phone. Installed JUI, and wanted to rollback to EUI via coolpad assistant. Couldn't do that because my PC wouldn't recognise my device, even though it did when flashing to JUI!
So I thought, why don't I flash a recovery via twrp - decided to flash recovery via miflash. Which was successful.
Now the phone doesn't switch on.
When a cable comes on, just two red lights flash.
I have tried to flash official firmware via YGDP and coolpad assistant. Phone is not recognised. uninstalled drivers and reinstalled them. To no avail. What do I do?
Click to expand...
Click to collapse
Official rollback with JUI on the EUI.
Download the archive https://mega.nz/#!n5whhDqA!X9i4VJCgcXhKv5GpgV5Tauhk0YrabFEF5Z85e4wUleg
Password for the archive: coolpadJUI2017
1. Unpack the archive
2. Install the Coolpad download assistent from the archive
3. Start Coolpad download assistent
4. Select init.cpb
5. Connect the phone in the mode bootloader to usb
6. The init.cpb firmware will go
7. After a minute or two, the automatic checking of the ROM.cpb file should go
8. After the verification, the firmware will go.
Done
How do I do that?
kassana69 said:
I've never bricked a phone. Installed JUI, and wanted to rollback to EUI via coolpad assistant. Couldn't do that because my PC wouldn't recognise my device, even though it did when flashing to JUI!
So I thought, why don't I flash a recovery via twrp - decided to flash recovery via miflash. Which was successful.
Now the phone doesn't switch on.
When a cable comes on, just two red lights flash.
I have tried to flash official firmware via YGDP and coolpad assistant. Phone is not recognised. uninstalled drivers and reinstalled them. To no avail. What do I do?
Click to expand...
Click to collapse
How u flashed through miflash? If possible can u send me files?? I can't flash TWRP in JUI becoz JUI Chinese rom can't be rooted...
Bricked my coolpad cool 1 after upgrading to JUI and rolling back to EUI
I have upgraded to JUI and didn't like the rom because many apps were failed to run and stopped. Couldn't install Gapps tried with Google Installer and also TWRP. So I decided to roll back and flashed EUI 18S unfortunately it was Chinese rom not the indian version. Decided to install Gapps but couldn't get into recovery.
Hence I thought to flash Indian version stock rom 17S through Coolpad Asisstant. While downgrading to the stock rom on indian version my phone bricked.
I cannot get into recovery. Tried all the combinations. I cannot get the device recognised as fastboot or ADB Devices.
The only way i can get the device recognised is by pressing volume + and volume - and the power button at a time and plug in the USB. The device gets detected in Qualcomm QDLoader mode 9008. I tried flashing stock recovery by QFIL and MIFlash.
But Still didn't work.
After phone. The phone tries to boot but switches off suddenly. I can only get into Qualcomm QDLoader mode 9008. Any suggestion that would help my phone get normal. I think it's hard bricked because it cannot get into recovery nor the fastboot mode. Thank you
---------- Post added at 02:41 PM ---------- Previous post was at 02:33 PM ----------
erica butson said:
I have upgraded to JUI and didn't like the rom because many apps were failed to run and stopped. Couldn't install Gapps tried with Google Installer and also TWRP. So I decided to roll back and flashed EUI 18S unfortunately it was Chinese rom not the indian version. Decided to install Gapps but couldn't get into recovery.
Hence I thought to flash Indian version stock rom 17S through Coolpad Asisstant. While downgrading to the stock rom on indian version my phone bricked.
I cannot get into recovery. Tried all the combinations. I cannot get the device recognised as fastboot or ADB Devices.
The only way i can get the device recognised is by pressing volume + and volume - and the power button at a time and plug in the USB. The device gets detected in Qualcomm QDLoader mode 9008. I tried flashing stock recovery by QFIL and MIFlash.
But Still didn't work.
After phone. The phone tries to boot but switches off suddenly. I can only get into Qualcomm QDLoader mode 9008. Any suggestion that would help my phone get normal. I think it's hard bricked because it cannot get into recovery nor the fastboot mode. Thank you
Click to expand...
Click to collapse
Validating Application Configuration
Load APP Configuration
COM:-1
PBLDOWNLOADPROTOCOL:0
PROGRAMMER:True
PROGRAMMER:C:\Users\jay\Desktop\QFILRecovery\prog_emmc_firehose.mbn
RESETSAHARASTATEEMACHINE:False
SEARCHPATH:C:\Users\jay\Desktop\QFILRecovery
RAWPROGRAM:
rawprogram0.xml
PATCH:
patch0.xml
ACKRAWDATAEVERYNUMPACKETS:False
ACKRAWDATAEVERYNUMPACKETS:100
MAXPAYLOADSIZETOTARGETINBYTES:False
MAXPAYLOADSIZETOTARGETINBYTES:49152
DEVICETYPE:eMMC
PLATFORM:8x26
VALIDATIONMODE:0
RESETAFTERDOWNLOAD:False
MAXDIGESTTABLESIZE:8192
SWITCHTOFIREHOSETIMEOUT:30
RESETTIMEOUT:200
RESETDELAYTIME:2
FLATBUILDPATH:C:\
FLATBUILDFORCEOVERRIDE:True
QCNPATH:C:\Temp\00000000.qcn
QCNAUTOBACKUPRESTORE:False
SPCCODE:000000
ENABLEMULTISIM:False
AUTOPRESERVEPARTITIONS:False
PARTITIONPRESERVEMODE:0
PRESERVEDPARTITIONS:0
PRESERVEDPARTITIONS:
ERASEALL:False
Load ARG Configuration
Validating Download Configuration
Search path not exist, ignored: C:\Users\jay\Desktop\QFILRecovery
Invalid programmer path, ignored: C:\Users\jay\Desktop\QFILRecovery\prog_emmc_firehose.mbn
Process Index:0
Programmer Path:C:\Users\jay\Desktop\UnbrickOfficial\recovery\prog_emmc_firehose_652.mbn
Image Search Path: C:\Users\jay\Desktop\UnbrickOfficial\recovery
Image Search Path: C:\Users\jay\Desktop\UnbrickOfficial\recovery
RAWPROGRAM file path: C:\Users\jay\Desktop\UnbrickOfficial\recovery\rawprogram0.xml
PATCH file path:C:\Users\jay\Desktop\UnbrickOfficial\recovery\patch0.xml
Start Download
Program Path:C:\Users\jay\Desktop\UnbrickOfficial\recovery\prog_emmc_firehose_652.mbn
***** Working Folder:C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3
Binary build date: Oct 31 2016 @ 22:51:05
QSAHARASERVER CALLED LIKE THIS: 'C:\Program Files (x86)\Qualcomm\QPST\bin\QSaharaServer.ex'Current working dir: C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3
Sahara mappings:
2: amss.mbn
6: apps.mbn
8: dsp1.mbn
10: dbl.mbn
11: osbl.mbn
12: dsp2.mbn
16: efs1.mbn
17: efs2.mbn
20: efs3.mbn
21: sbl1.mbn
22: sbl2.mbn
23: rpm.mbn
25: tz.mbn
28: dsp3.mbn
29: acdb.mbn
30: wdt.mbn
31: mba.mbn
13: C:\Users\jay\Desktop\UnbrickOfficial\recovery\prog_emmc_firehose_652.mbn
19:49:35: Requested ID 13, file: "C:\Users\jay\Desktop\UnbrickOfficial\recovery\prog_emmc_firehose_652.mbn"
19:49:35: 349340 bytes transferred in 0.250000 seconds (1.3326MBps)
19:49:35: File transferred successfully
NOTE: Target requested image 13 which is DeviceProgrammer. Forcing QUIT. This is by design, ** All is well ** SUCCESS!!
19:49:35: Sahara protocol completed
Sending Programmer Finished
Switch To FireHose
Wait for 3 seconds...
Max Payload Size to Target:49152 Bytes
Device Type:eMMC
Platform:8x26
Disable Ack Raw Data Every N Packets
Skip Write:False
Always Validate:False
Use Verbose:False
***** Working Folder:C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3
Base Version: 16.10.28.15.28
Binary build date: Oct 31 2016 @ 22:51:02
Incremental Build version: 16.10.31.22.51.02
19:49:39: INFO: FH_LOADER WAS CALLED EXACTLY LIKE THIS
************************************************
C:\Program Files (x86)\Qualcomm\QPST\bin\fh_loader.exe --port=\\.\COM3 --sendxml=rawprogram0.xml --search_path=C:\Users\jay\Desktop\UnbrickOfficial\recovery --noprompt --showpercentagecomplete --zlpawarehost=1 --memoryname=emmc
************************************************
19:49:39: INFO: Current working dir (cwd): C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\
19:49:39: INFO: Showing network mappings to allow debugging
19:49:39: INFO:
19:49:39: INFO: Trying to store 'rawprogram0.xml' in string table
19:49:39: INFO: Looking for file 'rawprogram0.xml'
19:49:39: INFO: User wants to talk to port '\\.\COM3'
19:49:39: INFO: Took 0.00000000 seconds to open port
19:49:39: INFO: Sorting TAGS to ensure order is <configure>,<erase>, others, <patch>,<power>
19:49:39: INFO: If you don't want this, use --dontsorttags
19:49:39: INFO: Looking for file 'recovery.img'
19:49:39: INFO:
Total to be tansferd with <program> or <read> is 16.10 MB
19:49:39: INFO: Sending <configure>
19:49:39: INFO: TARGET SAID: '[email protected] [email protected]'
19:49:39: INFO: fh.attrs.MaxPayloadSizeToTargetInBytes = 1048576
19:49:39: INFO: fh.attrs.MaxPayloadSizeToTargetInBytesSupported = 1048576
19:49:39: INFO: In handleProgram('recovery.img')
19:49:39: INFO: Looking for file 'recovery.img'
19:49:39: INFO: =======================================================
19:49:39: INFO: {<program> FILE: 'C:\Users\jay\Desktop\UnbrickOfficial\recovery\recovery.img'}
19:49:39: INFO: {<program> (16.10 MB) 32980 sectors needed at location 896096 on LUN 0}
19:49:39: INFO: =======================================================
19:49:39: INFO: TARGET SAID: '[email protected] [email protected]'
19:49:39: INFO: TARGET SAID: 'start 896096, num 32980'
19:49:40: INFO: Overall to target 0.735 seconds (21.91 MBps)
19:49:40: INFO: {percent files transferred 100.00%}
19:49:40: INFO: TARGET SAID: 'Finished sector address 929076'
19:49:40: INFO:
19:49:40: INFO: =======================================================
19:49:40: INFO: ==================== {SUCCESS} ========================
19:49:40: INFO: =======================================================
19:49:40: INFO: {percent files transferred 100.00%}
19:49:40: INFO: ==============================================================
19:49:40: INFO: Files used and their paths
19:49:40: INFO: 1 'C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\port_trace.txt'
19:49:40: INFO: 2 'C:\Users\jay\Desktop\UnbrickOfficial\recovery\rawprogram0.xml'
19:49:40: INFO: 3 'C:\Users\jay\Desktop\UnbrickOfficial\recovery\recovery.img'
19:49:40: INFO: _ (done)
19:49:40: INFO: | |
19:49:40: INFO: __| | ___ _ __ ___
19:49:40: INFO: / _` |/ _ \| '_ \ / _ \
19:49:40: INFO: | (_| | (_) | | | | __/
19:49:40: INFO: \__,_|\___/|_| |_|\___|
19:49:40: INFO: {All Finished Successfully}
19:49:40: INFO: Overall to target 0.844 seconds (19.08 MBps)
19:49:40: INFO: {percent files transferred 100.00%}
Writing log to 'C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\port_trace.txt', might take a minute
Log is 'C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\port_trace.txt'
***** Working Folder:C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3
Base Version: 16.10.28.15.28
Binary build date: Oct 31 2016 @ 22:51:02
Incremental Build version: 16.10.31.22.51.02
19:49:40: INFO: FH_LOADER WAS CALLED EXACTLY LIKE THIS
************************************************
C:\Program Files (x86)\Qualcomm\QPST\bin\fh_loader.exe --port=\\.\COM3 --sendxml=patch0.xml --search_path=C:\Users\jay\Desktop\UnbrickOfficial\recovery --noprompt --showpercentagecomplete --zlpawarehost=1 --memoryname=emmc
************************************************
19:49:40: INFO: Current working dir (cwd): C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\
19:49:40: INFO: Showing network mappings to allow debugging
19:49:41: INFO:
19:49:41: INFO: Trying to store 'patch0.xml' in string table
19:49:41: INFO: Looking for file 'patch0.xml'
19:49:41: INFO: User wants to talk to port '\\.\COM3'
19:49:41: INFO: Took 0.00000000 seconds to open port
19:49:41: INFO: Sorting TAGS to ensure order is <configure>,<erase>, others, <patch>,<power>
19:49:41: INFO: If you don't want this, use --dontsorttags
19:49:41: INFO: Sending <configure>
19:49:41: INFO: TARGET SAID: '[email protected] [email protected]'
19:49:41: INFO: fh.attrs.MaxPayloadSizeToTargetInBytes = 1048576
19:49:41: INFO: fh.attrs.MaxPayloadSizeToTargetInBytesSupported = 1048576
19:49:41: INFO: TARGET SAID: 'Patched sector 16 with 03A3DFDE'
19:49:41: INFO: TARGET SAID: 'Patched sector 61071341 with 03A3DFDE'
19:49:41: INFO: TARGET SAID: 'Patched sector 1 with 03A3DFDE'
19:49:41: INFO: TARGET SAID: 'Patched sector 61071359 with 03A3DFDE'
19:49:41: INFO: TARGET SAID: 'Patched sector 1 with 03A3DFFF'
19:49:41: INFO: TARGET SAID: 'Patched sector 61071359 with 03A3DFFF'
19:49:41: INFO: TARGET SAID: 'Patched sector 61071359 with 03A3DFDF'
19:49:41: INFO: TARGET SAID: 'crc start sector 2, over bytes 7680'
19:49:41: INFO: TARGET SAID: 'Patched sector 1 with 77C000D3'
19:49:41: INFO: TARGET SAID: 'crc start sector 61071327, over bytes 7680'
19:49:41: INFO: TARGET SAID: 'Patched sector 61071359 with 77C000D3'
19:49:41: INFO: TARGET SAID: 'Patched sector 1 with 00000000'
19:49:41: INFO: TARGET SAID: 'crc start sector 1, over bytes 92'
19:49:41: INFO: TARGET SAID: 'Patched sector 1 with FEA83C6E'
19:49:41: INFO: TARGET SAID: 'Patched sector 61071359 with 00000000'
19:49:41: INFO: TARGET SAID: 'crc start sector 61071359, over bytes 92'
19:49:41: INFO: TARGET SAID: 'Patched sector 61071359 with 42876C66'
19:49:41: INFO: ==============================================================
19:49:41: INFO: Files used and their paths
19:49:41: INFO: 1 'C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\port_trace.txt'
19:49:41: INFO: 2 'C:\Users\jay\Desktop\UnbrickOfficial\recovery\patch0.xml'
19:49:41: INFO: _ (done)
19:49:41: INFO: | |
19:49:41: INFO: __| | ___ _ __ ___
19:49:41: INFO: / _` |/ _ \| '_ \ / _ \
19:49:41: INFO: | (_| | (_) | | | | __/
19:49:41: INFO: \__,_|\___/|_| |_|\___|
19:49:41: INFO: {All Finished Successfully}
19:49:41: INFO: FILE ACCESS SLOW!! 0.00 B in 0.015 seconds ( 0.00 Bps) --- Overall to target 0.437 seconds (0.00 Bps)
Writing log to 'C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\port_trace.txt', might take a minute
Log is 'C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\port_trace.txt'
***** Working Folder:C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3
Base Version: 16.10.28.15.28
Binary build date: Oct 31 2016 @ 22:51:02
Incremental Build version: 16.10.31.22.51.02
19:49:42: INFO: FH_LOADER WAS CALLED EXACTLY LIKE THIS
************************************************
C:\Program Files (x86)\Qualcomm\QPST\bin\fh_loader.exe --port=\\.\COM3 --setactivepartition=0 --noprompt --showpercentagecomplete --zlpawarehost=1 --memoryname=emmc
************************************************
19:49:42: INFO: Current working dir (cwd): C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\
19:49:42: INFO: Showing network mappings to allow debugging
19:49:42: INFO: User wants to talk to port '\\.\COM3'
19:49:42: INFO: Took 0.00000000 seconds to open port
19:49:42: INFO: Sorting TAGS to ensure order is <configure>,<erase>, others, <patch>,<power>
19:49:42: INFO: If you don't want this, use --dontsorttags
19:49:42: INFO: Sending <configure>
19:49:42: INFO: TARGET SAID: '[email protected] [email protected]'
19:49:42: INFO: fh.attrs.MaxPayloadSizeToTargetInBytes = 1048576
19:49:42: INFO: fh.attrs.MaxPayloadSizeToTargetInBytesSupported = 1048576
19:49:42: INFO: Sending <setbootablestoragedrive>
19:49:42: INFO: TARGET SAID: 'Set bootable drive to 0.'
19:49:42: INFO: ==============================================================
19:49:42: INFO: Files used and their paths
19:49:42: INFO: 1 'C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\port_trace.txt'
19:49:42: INFO: _ (done)
19:49:42: INFO: | |
19:49:42: INFO: __| | ___ _ __ ___
19:49:42: INFO: / _` |/ _ \| '_ \ / _ \
19:49:42: INFO: | (_| | (_) | | | | __/
19:49:42: INFO: \__,_|\___/|_| |_|\___|
19:49:42: INFO: {All Finished Successfully}
19:49:42: INFO: FILE ACCESS SLOW!! 0.00 B in 0.015 seconds ( 0.00 Bps) --- Overall to target 0.062 seconds (0.00 Bps)
Writing log to 'C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\port_trace.txt', might take a minute
Log is 'C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\port_trace.txt'
Download Succeed
Finish Download
sumanta15.05 said:
You can flash using QPST, I did that to unbrick my phone.
Extract the CPB and flash using QFIL.
But please do backup your phone internal before that. I fixed my brick but cant fix my baseband as I forgot to take a backup.
It would be a favor if anyone could send their QCN backed up ( in private message , be ensured that I will use my own imei number )
Click to expand...
Click to collapse
Hi,
I tried install TWRP via MiFlash on Letv Cool1 c106 4gb/64 - eui, rom Leree. The operation has completed. But now I have a problem, mobile blinking red light when plugged in PC. I can't turn on it. I think I brick it. What can I do, it is possible to ubrick him ?
Please help me.
how you succeed?? i tried but failed. Can you help me plz
erica butson said:
I have upgraded to JUI and didn't like the rom because many apps were failed to run and stopped. Couldn't install Gapps tried with Google Installer and also TWRP. So I decided to roll back and flashed EUI 18S unfortunately it was Chinese rom not the indian version. Decided to install Gapps but couldn't get into recovery.
Hence I thought to flash Indian version stock rom 17S through Coolpad Asisstant. While downgrading to the stock rom on indian version my phone bricked.
I cannot get into recovery. Tried all the combinations. I cannot get the device recognised as fastboot or ADB Devices.
The only way i can get the device recognised is by pressing volume + and volume - and the power button at a time and plug in the USB. The device gets detected in Qualcomm QDLoader mode 9008. I tried flashing stock recovery by QFIL and MIFlash.
But Still didn't work.
After phone. The phone tries to boot but switches off suddenly. I can only get into Qualcomm QDLoader mode 9008. Any suggestion that would help my phone get normal. I think it's hard bricked because it cannot get into recovery nor the fastboot mode. Thank you
---------- Post added at 02:41 PM ---------- Previous post was at 02:33 PM ----------
Validating Application Configuration
Load APP Configuration
COM:-1
PBLDOWNLOADPROTOCOL:0
PROGRAMMER:True
PROGRAMMER:C:\Users\jay\Desktop\QFILRecovery\prog_emmc_firehose.mbn
RESETSAHARASTATEEMACHINE:False
SEARCHPATH:C:\Users\jay\Desktop\QFILRecovery
RAWPROGRAM:
rawprogram0.xml
PATCH:
patch0.xml
ACKRAWDATAEVERYNUMPACKETS:False
ACKRAWDATAEVERYNUMPACKETS:100
MAXPAYLOADSIZETOTARGETINBYTES:False
MAXPAYLOADSIZETOTARGETINBYTES:49152
DEVICETYPE:eMMC
PLATFORM:8x26
VALIDATIONMODE:0
RESETAFTERDOWNLOAD:False
MAXDIGESTTABLESIZE:8192
SWITCHTOFIREHOSETIMEOUT:30
RESETTIMEOUT:200
RESETDELAYTIME:2
FLATBUILDPATH:C:\
FLATBUILDFORCEOVERRIDE:True
QCNPATH:C:\Temp\00000000.qcn
QCNAUTOBACKUPRESTORE:False
SPCCODE:000000
ENABLEMULTISIM:False
AUTOPRESERVEPARTITIONS:False
PARTITIONPRESERVEMODE:0
PRESERVEDPARTITIONS:0
PRESERVEDPARTITIONS:
ERASEALL:False
Load ARG Configuration
Validating Download Configuration
Search path not exist, ignored: C:\Users\jay\Desktop\QFILRecovery
Invalid programmer path, ignored: C:\Users\jay\Desktop\QFILRecovery\prog_emmc_firehose.mbn
Process Index:0
Programmer Path:C:\Users\jay\Desktop\UnbrickOfficial\recovery\prog_emmc_firehose_652.mbn
Image Search Path: C:\Users\jay\Desktop\UnbrickOfficial\recovery
Image Search Path: C:\Users\jay\Desktop\UnbrickOfficial\recovery
RAWPROGRAM file path: C:\Users\jay\Desktop\UnbrickOfficial\recovery\rawprogram0.xml
PATCH file path:C:\Users\jay\Desktop\UnbrickOfficial\recovery\patch0.xml
Start Download
Program Path:C:\Users\jay\Desktop\UnbrickOfficial\recovery\prog_emmc_firehose_652.mbn
***** Working Folder:C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3
Binary build date: Oct 31 2016 @ 22:51:05
QSAHARASERVER CALLED LIKE THIS: 'C:\Program Files (x86)\Qualcomm\QPST\bin\QSaharaServer.ex'Current working dir: C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3
Sahara mappings:
2: amss.mbn
6: apps.mbn
8: dsp1.mbn
10: dbl.mbn
11: osbl.mbn
12: dsp2.mbn
16: efs1.mbn
17: efs2.mbn
20: efs3.mbn
21: sbl1.mbn
22: sbl2.mbn
23: rpm.mbn
25: tz.mbn
28: dsp3.mbn
29: acdb.mbn
30: wdt.mbn
31: mba.mbn
13: C:\Users\jay\Desktop\UnbrickOfficial\recovery\prog_emmc_firehose_652.mbn
19:49:35: Requested ID 13, file: "C:\Users\jay\Desktop\UnbrickOfficial\recovery\prog_emmc_firehose_652.mbn"
19:49:35: 349340 bytes transferred in 0.250000 seconds (1.3326MBps)
19:49:35: File transferred successfully
NOTE: Target requested image 13 which is DeviceProgrammer. Forcing QUIT. This is by design, ** All is well ** SUCCESS!!
19:49:35: Sahara protocol completed
Sending Programmer Finished
Switch To FireHose
Wait for 3 seconds...
Max Payload Size to Target:49152 Bytes
Device Type:eMMC
Platform:8x26
Disable Ack Raw Data Every N Packets
Skip Write:False
Always Validate:False
Use Verbose:False
***** Working Folder:C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3
Base Version: 16.10.28.15.28
Binary build date: Oct 31 2016 @ 22:51:02
Incremental Build version: 16.10.31.22.51.02
19:49:39: INFO: FH_LOADER WAS CALLED EXACTLY LIKE THIS
************************************************
C:\Program Files (x86)\Qualcomm\QPST\bin\fh_loader.exe --port=\\.\COM3 --sendxml=rawprogram0.xml --search_path=C:\Users\jay\Desktop\UnbrickOfficial\recovery --noprompt --showpercentagecomplete --zlpawarehost=1 --memoryname=emmc
************************************************
19:49:39: INFO: Current working dir (cwd): C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\
19:49:39: INFO: Showing network mappings to allow debugging
19:49:39: INFO:
19:49:39: INFO: Trying to store 'rawprogram0.xml' in string table
19:49:39: INFO: Looking for file 'rawprogram0.xml'
19:49:39: INFO: User wants to talk to port '\\.\COM3'
19:49:39: INFO: Took 0.00000000 seconds to open port
19:49:39: INFO: Sorting TAGS to ensure order is <configure>,<erase>, others, <patch>,<power>
19:49:39: INFO: If you don't want this, use --dontsorttags
19:49:39: INFO: Looking for file 'recovery.img'
19:49:39: INFO:
Total to be tansferd with <program> or <read> is 16.10 MB
19:49:39: INFO: Sending <configure>
19:49:39: INFO: TARGET SAID: '[email protected] [email protected]'
19:49:39: INFO: fh.attrs.MaxPayloadSizeToTargetInBytes = 1048576
19:49:39: INFO: fh.attrs.MaxPayloadSizeToTargetInBytesSupported = 1048576
19:49:39: INFO: In handleProgram('recovery.img')
19:49:39: INFO: Looking for file 'recovery.img'
19:49:39: INFO: =======================================================
19:49:39: INFO: {<program> FILE: 'C:\Users\jay\Desktop\UnbrickOfficial\recovery\recovery.img'}
19:49:39: INFO: {<program> (16.10 MB) 32980 sectors needed at location 896096 on LUN 0}
19:49:39: INFO: =======================================================
19:49:39: INFO: TARGET SAID: '[email protected] [email protected]'
19:49:39: INFO: TARGET SAID: 'start 896096, num 32980'
19:49:40: INFO: Overall to target 0.735 seconds (21.91 MBps)
19:49:40: INFO: {percent files transferred 100.00%}
19:49:40: INFO: TARGET SAID: 'Finished sector address 929076'
19:49:40: INFO:
19:49:40: INFO: =======================================================
19:49:40: INFO: ==================== {SUCCESS} ========================
19:49:40: INFO: =======================================================
19:49:40: INFO: {percent files transferred 100.00%}
19:49:40: INFO: ==============================================================
19:49:40: INFO: Files used and their paths
19:49:40: INFO: 1 'C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\port_trace.txt'
19:49:40: INFO: 2 'C:\Users\jay\Desktop\UnbrickOfficial\recovery\rawprogram0.xml'
19:49:40: INFO: 3 'C:\Users\jay\Desktop\UnbrickOfficial\recovery\recovery.img'
19:49:40: INFO: _ (done)
19:49:40: INFO: | |
19:49:40: INFO: __| | ___ _ __ ___
19:49:40: INFO: / _` |/ _ \| '_ \ / _ \
19:49:40: INFO: | (_| | (_) | | | | __/
19:49:40: INFO: \__,_|\___/|_| |_|\___|
19:49:40: INFO: {All Finished Successfully}
19:49:40: INFO: Overall to target 0.844 seconds (19.08 MBps)
19:49:40: INFO: {percent files transferred 100.00%}
Writing log to 'C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\port_trace.txt', might take a minute
Log is 'C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\port_trace.txt'
***** Working Folder:C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3
Base Version: 16.10.28.15.28
Binary build date: Oct 31 2016 @ 22:51:02
Incremental Build version: 16.10.31.22.51.02
19:49:40: INFO: FH_LOADER WAS CALLED EXACTLY LIKE THIS
************************************************
C:\Program Files (x86)\Qualcomm\QPST\bin\fh_loader.exe --port=\\.\COM3 --sendxml=patch0.xml --search_path=C:\Users\jay\Desktop\UnbrickOfficial\recovery --noprompt --showpercentagecomplete --zlpawarehost=1 --memoryname=emmc
************************************************
19:49:40: INFO: Current working dir (cwd): C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\
19:49:40: INFO: Showing network mappings to allow debugging
19:49:41: INFO:
19:49:41: INFO: Trying to store 'patch0.xml' in string table
19:49:41: INFO: Looking for file 'patch0.xml'
19:49:41: INFO: User wants to talk to port '\\.\COM3'
19:49:41: INFO: Took 0.00000000 seconds to open port
19:49:41: INFO: Sorting TAGS to ensure order is <configure>,<erase>, others, <patch>,<power>
19:49:41: INFO: If you don't want this, use --dontsorttags
19:49:41: INFO: Sending <configure>
19:49:41: INFO: TARGET SAID: '[email protected] [email protected]'
19:49:41: INFO: fh.attrs.MaxPayloadSizeToTargetInBytes = 1048576
19:49:41: INFO: fh.attrs.MaxPayloadSizeToTargetInBytesSupported = 1048576
19:49:41: INFO: TARGET SAID: 'Patched sector 16 with 03A3DFDE'
19:49:41: INFO: TARGET SAID: 'Patched sector 61071341 with 03A3DFDE'
19:49:41: INFO: TARGET SAID: 'Patched sector 1 with 03A3DFDE'
19:49:41: INFO: TARGET SAID: 'Patched sector 61071359 with 03A3DFDE'
19:49:41: INFO: TARGET SAID: 'Patched sector 1 with 03A3DFFF'
19:49:41: INFO: TARGET SAID: 'Patched sector 61071359 with 03A3DFFF'
19:49:41: INFO: TARGET SAID: 'Patched sector 61071359 with 03A3DFDF'
19:49:41: INFO: TARGET SAID: 'crc start sector 2, over bytes 7680'
19:49:41: INFO: TARGET SAID: 'Patched sector 1 with 77C000D3'
19:49:41: INFO: TARGET SAID: 'crc start sector 61071327, over bytes 7680'
19:49:41: INFO: TARGET SAID: 'Patched sector 61071359 with 77C000D3'
19:49:41: INFO: TARGET SAID: 'Patched sector 1 with 00000000'
19:49:41: INFO: TARGET SAID: 'crc start sector 1, over bytes 92'
19:49:41: INFO: TARGET SAID: 'Patched sector 1 with FEA83C6E'
19:49:41: INFO: TARGET SAID: 'Patched sector 61071359 with 00000000'
19:49:41: INFO: TARGET SAID: 'crc start sector 61071359, over bytes 92'
19:49:41: INFO: TARGET SAID: 'Patched sector 61071359 with 42876C66'
19:49:41: INFO: ==============================================================
19:49:41: INFO: Files used and their paths
19:49:41: INFO: 1 'C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\port_trace.txt'
19:49:41: INFO: 2 'C:\Users\jay\Desktop\UnbrickOfficial\recovery\patch0.xml'
19:49:41: INFO: _ (done)
19:49:41: INFO: | |
19:49:41: INFO: __| | ___ _ __ ___
19:49:41: INFO: / _` |/ _ \| '_ \ / _ \
19:49:41: INFO: | (_| | (_) | | | | __/
19:49:41: INFO: \__,_|\___/|_| |_|\___|
19:49:41: INFO: {All Finished Successfully}
19:49:41: INFO: FILE ACCESS SLOW!! 0.00 B in 0.015 seconds ( 0.00 Bps) --- Overall to target 0.437 seconds (0.00 Bps)
Writing log to 'C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\port_trace.txt', might take a minute
Log is 'C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\port_trace.txt'
***** Working Folder:C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3
Base Version: 16.10.28.15.28
Binary build date: Oct 31 2016 @ 22:51:02
Incremental Build version: 16.10.31.22.51.02
19:49:42: INFO: FH_LOADER WAS CALLED EXACTLY LIKE THIS
************************************************
C:\Program Files (x86)\Qualcomm\QPST\bin\fh_loader.exe --port=\\.\COM3 --setactivepartition=0 --noprompt --showpercentagecomplete --zlpawarehost=1 --memoryname=emmc
************************************************
19:49:42: INFO: Current working dir (cwd): C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\
19:49:42: INFO: Showing network mappings to allow debugging
19:49:42: INFO: User wants to talk to port '\\.\COM3'
19:49:42: INFO: Took 0.00000000 seconds to open port
19:49:42: INFO: Sorting TAGS to ensure order is <configure>,<erase>, others, <patch>,<power>
19:49:42: INFO: If you don't want this, use --dontsorttags
19:49:42: INFO: Sending <configure>
19:49:42: INFO: TARGET SAID: '[email protected] [email protected]'
19:49:42: INFO: fh.attrs.MaxPayloadSizeToTargetInBytes = 1048576
19:49:42: INFO: fh.attrs.MaxPayloadSizeToTargetInBytesSupported = 1048576
19:49:42: INFO: Sending <setbootablestoragedrive>
19:49:42: INFO: TARGET SAID: 'Set bootable drive to 0.'
19:49:42: INFO: ==============================================================
19:49:42: INFO: Files used and their paths
19:49:42: INFO: 1 'C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\port_trace.txt'
19:49:42: INFO: _ (done)
19:49:42: INFO: | |
19:49:42: INFO: __| | ___ _ __ ___
19:49:42: INFO: / _` |/ _ \| '_ \ / _ \
19:49:42: INFO: | (_| | (_) | | | | __/
19:49:42: INFO: \__,_|\___/|_| |_|\___|
19:49:42: INFO: {All Finished Successfully}
19:49:42: INFO: FILE ACCESS SLOW!! 0.00 B in 0.015 seconds ( 0.00 Bps) --- Overall to target 0.062 seconds (0.00 Bps)
Writing log to 'C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\port_trace.txt', might take a minute
Log is 'C:\Users\jay\AppData\Roaming\Qualcomm\QFIL\COMPORT_3\port_trace.txt'
Download Succeed
Finish Download
Click to expand...
Click to collapse
need help
My calls are mute, I do not hear anyone calling.
I tried this procedure but my phone is not identified by Colpad Download, I installed JUI but my phone is muted in calls I do not hear anything in calls and anyone who calls me does not hear me.
How can I open a TOPIC to see if someone helps me solve this?
Off-topic, but if you haven't signed already, please do so https://www.change.org/p/coolpad-kernel-sources-for-cool1 and let's hope the kernel sources are released soon
how to use QFIL to install CBP?
sumanta15.05 said:
You can flash using QPST, I did that to unbrick my phone.
Extract the CPB and flash using QFIL.
But please do backup your phone internal before that. I fixed my brick but cant fix my baseband as I forgot to take a backup.
It would be a favor if anyone could send their QCN backed up ( in private message , be ensured that I will use my own imei number )
Click to expand...
Click to collapse
my phone is not identified by COOL ASSISTANT but QFIL identifies it, how do I give DOWNGRADE using QFIL? : eek:
Restore Coolpad Cool 1 Bricked
kassana69 said:
I've never bricked a phone. Installed JUI, and wanted to rollback to EUI via coolpad assistant. Couldn't do that because my PC wouldn't recognise my device, even though it did when flashing to JUI!
So I thought, why don't I flash a recovery via twrp - decided to flash recovery via miflash. Which was successful.
Now the phone doesn't switch on.
When a cable comes on, just two red lights flash.
I have tried to flash official firmware via YGDP and coolpad assistant. Phone is not recognised. uninstalled drivers and reinstalled them. To no avail. What do I do?
Click to expand...
Click to collapse
Recovery for COOL1 deleted.
First of all, you need to download the necessary files:
GROSSOSHOP / MIFLASH driver / COOLPAD / ROOM recovery driver / Installation ROOM / EUI_TWRP_6.0.1.
• 1º install all drivers and MIFLASH
Remember that your device is erasing and only flashes the red light when connected to your computer, if your cell phone is in this state is a good sign as we will be able to get it to be identified to install the room;
2º HOW TO MAKE THE APPLIANCE IDENTIFIED ON THE PC
With the installed drivers connect your cell phone to your computer, open the Control Panel go to Device Manager and leave the screen open to observe: now with the phone connected we will press together the volume +, volume - and Power button together and secure them until the phone is identified by the system on the DEVICE MANAGER page (for the phone to be identified it may be necessary to keep pressing the buttons for more than 60 seconds, if it is not identified at the end of 120 seconds repeat the process of tightening buttons until the system identifies them).
• In case the system identifies but does not automatically install the driver it is necessary to perform a forced installation:
3º Forced driver installation:
With Device Manager open, we have the device to the computer, it has not been installed correctly for which it is necessary to perform the forced installation procedure. If the installation is not successful, the WINDOWS DRIVER DIGITAL SIGNATURE may be active and the installation of a set to first of all will disable it:
• Then type in the Windows search field and query by CMD, right-click and select to run as administrator with the command prompt open in administrator mode enter the following command without the quotes "bcdedit / set loadoptions DDISABLE_INTEGRITY_CHECKS "Ready a driver signature to be disabled, let's now forge a driver installation.
Right-click on the identified device but it is not recognized and select UPDATE DIVER, now on PROBE DRIVER SOFTWARE ON THE COMPUTER, click PERMIT THAT I CHOOSE ON A LIST OF AVAILABLE DRIVERS IN MY COMPUTER now in NEXT and on click in WITH THE DISK; Browse to your local disk where the driver was installed, LENOVO folder, normally installed in the directory: C: \ Program Files (x86) \ LenovoUsbDriver \ Navigate to a subfolder SERIAL and select the following file -Lenovo_ser click open and then In OK, Look for Qualcomm HS-USB QDLoader 9008 and confirm installation, prompt your device is now correctly connected and available and available for MIFLASH.
4º USING MIFLASH
Now with the drivers properly installed open the MIFLASH 1 click on REFRESH 2 select the folder of the recovery room that must be unzipped and 3 click on FLASH wait until the process finishes "in my case presented error at the end of the installation, but did not interfere , the process was enough so that I could already open the recovery mode of the mobile. "
• With the MIFLASH still open now press the Power button, volume - and volume + again until you make the identification noise on your computer again, in MIFLASH search for the EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92 folder and select the twrp subfolder and a REFRESH from your device should be recognized by MIFLASH, now click on FLASH and wait for the end of the installation.
With the twrp installed enter into recovery mode on your cell phone by pressing the Power buttons and the volume + button, click Wipe, Format Data, type yes and confirm this will delete your cell partition. Go back to twrp home screen click on Mount Disable MTP and then on ENABLE MTP, you can now transfer files to your mobile phone, transfer to the device's internal memory to android rom 6.0.1 COOL1_C106_R3_5.8.018S_ROW_BB72-CUOCO92_2 as soon as the transfer finish go back to the twrp menu screen go to INSTALL select the room wait for the installation "now without errors" and your device will start normally after a few minutes.
I can not post the download links the site does not allow me to be a new user, but to those who want to send me a private message that I forward the download links :good:
Unbrick you're phone using this detailed guide on pantomath site
IMEI restore. Coolpad phones are unbrickable. Follow this guide
sumanta15.05 said:
You can flash using QPST, I did that to unbrick my phone.
Extract the CPB and flash using QFIL.
But please do backup your phone internal before that. I fixed my brick but cant fix my baseband as I forgot to take a backup.
It would be a favor if anyone could send their QCN backed up ( in private message , be ensured that I will use my own imei number )
Click to expand...
Click to collapse
do you have a baseband backup? I bricked mine and flashed a baseband given in forum. Now i can no longer get 4g LTE connection. Device is C103. I need a QCN.
Hii my cool 1 c103 has been bricked stuck in the penguin logo no fastboot mode no recovery mode also not getting detected in qdloader 9008 in pc help me guys when i connect my phone to pc the phone gets connected in android bootloaader interface help me someone not recognized in qfill only red light blinks in screen penguin logo no recovery mode no fastboot
QCN
vulturext said:
do you have a baseband backup? I bricked mine and flashed a baseband given in forum. Now i can no longer get 4g LTE connection. Device is C103. I need a QCN.
Click to expand...
Click to collapse
I fixed mine using a qcn file from a Chinese or Russian site.
Google for c103 qcn and there would be a link for the QCN. It's around 100-200kb.
kishan nagrecha said:
Hii my cool 1 c103 has been bricked stuck in the penguin logo no fastboot mode no recovery mode also not getting detected in qdloader 9008 in pc help me guys when i connect my phone to pc the phone gets connected in android bootloaader interface help me someone not recognized in qfill only red light blinks in screen penguin logo no recovery mode no fastboot
Click to expand...
Click to collapse
keep pressing power+vol up+vol down until it got detected. Install all the drivers first.
sumanta15.05 said:
I fixed mine using a qcn file from a Chinese or Russian site.
Google for c103 qcn and there would be a link for the QCN. It's around 100-200kb.
Click to expand...
Click to collapse
Thanks.... Found the QCN of C103 online and flashed it, problem solved.
---------- Post added at 12:39 PM ---------- Previous post was at 12:35 PM ----------
If anyone needs QCN of C103, the same can be downloaded from the following link.
https://mega.nz/#!FQp0jC6L!UiczUgnYjK4CIPpv05ifN_VzBcH9m50G_OTACHAVlqw
Password - Coolpas [email protected]
I am not the owner of the file but downloaded the same from the following link
http://forum.gsmdevelopers.com/cool...coolpad-cool-1-c103-root-twrp-qcn-tested.html
I had the issue of no network and the above given QCN resolved the issue. Hence I am posting links here to help others.
imei and qcn restored however network signal is not showing
I have recovered to eui ( c-103) from hard brick using qfil. however my imei numbers and network signals went off. I was able to get back my imei using imei write softwares and restore qcn etc. However , i still my network status is showing disabled. Please help me in this regard
chandunss said:
I have recovered to eui ( c-103) from hard brick using qfil. however my imei numbers and network signals went off. I was able to get back my imei using imei write softwares and restore qcn etc. However , i still my network status is showing disabled. Please help me in this regard
Click to expand...
Click to collapse
Which qcn file you restored??
my phone stuck in corrupted recovery mode but i can still access edl mode. i can't flash another custom recovery and can't flash stock rom too, it always says:
Validating Application Configuration
Load APP Configuration
COM:4
PBLDOWNLOADPROTOCOL:0
PROGRAMMER:True
PROGRAMMER:E:\Installers\EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92\twrp\prog_emmc_firehose_652.mbn
RESETSAHARASTATEEMACHINE:False
SEARCHPATH:E:\Installers\EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92\twrp
RAWPROGRAM:
rawprogram0.xml
PATCH:
patch0.xml
ACKRAWDATAEVERYNUMPACKETS:False
ACKRAWDATAEVERYNUMPACKETS:100
MAXPAYLOADSIZETOTARGETINBYTES:False
MAXPAYLOADSIZETOTARGETINBYTES:49152
DEVICETYPE:eMMC
PLATFORM:8x26
VALIDATIONMODE:0
RESETAFTERDOWNLOAD:False
MAXDIGESTTABLESIZE:8192
SWITCHTOFIREHOSETIMEOUT:30
RESETTIMEOUT:200
RESETDELAYTIME:2
FLATBUILDPATH:C:\
FLATBUILDFORCEOVERRIDE:True
QCNPATH:C:\Temp\00000000.qcn
QCNAUTOBACKUPRESTORE:False
SPCCODE:000000
ENABLEMULTISIM:False
AUTOPRESERVEPARTITIONS:False
PARTITIONPRESERVEMODE:0
PRESERVEDPARTITIONS:0
PRESERVEDPARTITIONS:
ERASEALL:False
Load ARG Configuration
Validating Download Configuration
Image Search Path: E:\Installers\EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92\twrp
RAWPROGRAM file path: E:\Installers\EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92\twrp\rawprogram0.xml
PATCH file path:E:\Installers\EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92\twrp\patch0.xml
Programmer Path:E:\Installers\EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92\twrp\prog_emmc_firehose_652.mbn
Process Index:0
Start Download
Program Path:E:\Installers\EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92\twrp\prog_emmc_firehose_652.mbn
***** Working Folder:C:\Users\Hans\AppData\Roaming\Qualcomm\QFIL\COMPORT_4
Binary build date: May 13 2015 @ 14:41:37
QSAHARASERVER CALLED LIKE THIS: 'C:\Program Files (x86)\Qualcomm\QPST\bin\QSaharaServer.exe -u 4 -s 13:E:\Installers\EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92\twrp\prog_emmc_firehose_652.mbn 'Current working dir: C:\Users\Hans\AppData\Roaming\Qualcomm\QFIL\COMPORT_4
Sahara mappings:
2: amss.mbn
6: apps.mbn
8: dsp1.mbn
10: dbl.mbn
11: osbl.mbn
12: dsp2.mbn
16: efs1.mbn
17: efs2.mbn
20: efs3.mbn
21: sbl1.mbn
22: sbl2.mbn
23: rpm.mbn
25: tz.mbn
28: dsp3.mbn
29: acdb.mbn
30: wdt.mbn
31: mba.mbn
Sending Programmer Finished
Switch To FireHose
Wait for 3 seconds...
Max Payload Size to Target:49152 Bytes
Device Type:eMMC
Platform:8x26
Disable Ack Raw Data Every N Packets
Skip Write:False
Always Validate:False
Use Verbose:False
***** Working Folder:C:\Users\Hans\AppData\Roaming\Qualcomm\QFIL\COMPORT_4
Binary build date: Jun 3 2015 @ 17:12:06
Build version: 15.06. 3.17.12.06
02:49:12: INFO: FH_LOADER WAS CALLED EXACTLY LIKE THIS
************************************************
C:\Program Files (x86)\Qualcomm\QPST\bin\fh_loader.exe --port=\\.\COM4 --sendxml=rawprogram0.xml --search_path=E:\Installers\EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92\twrp --noprompt --showpercentagecomplete --zlpawarehost=1 --memoryname=emmc
************************************************
02:49:12: INFO: Current working dir (cwd): C:\Users\Hans\AppData\Roaming\Qualcomm\QFIL\COMPORT_4\
02:49:12: INFO: Showing network mappings to allow debugging
02:49:12: INFO:
02:49:12: INFO: Trying to store 'rawprogram0.xml' in string table
02:49:12: INFO: Looking for file 'rawprogram0.xml'
02:49:12: INFO: User wants to talk to port '\\.\COM4'
02:49:12: INFO: Took 0.01500000 seconds to open port
02:49:12: INFO: Sorting TAGS to ensure order is <configure>,<erase>, others, <patch>,<power>
02:49:12: INFO: If you don't want this, use --dontsorttags
02:49:12: INFO: Looking for file 'recovery.img'
02:49:12: INFO: Looking for file 'boot.img'
02:49:12: INFO:
Total to be tansferd with <program> or <read> is 35.30 MB
02:49:12: INFO: Sending <configure>
_____
| ___|
| |__ _ __ _ __ ___ _ __
| __| '__| '__/ _ \| '__|
| |__| | | | | (_) | |
\____/_| |_| \___/|_|
02:49:12: {ERROR: XML not formed correctly. Expected a < character at loc 0}
_____
| ___|
| |__ _ __ _ __ ___ _ __
| __| '__| '__/ _ \| '__|
| |__| | | | | (_) | |
\____/_| |_| \___/|_|
02:49:12: {ERROR: 3. TAG not found or recognized}
_____
| ___|
| |__ _ __ _ __ ___ _ __
| __| '__| '__/ _ \| '__|
| |__| | | | | (_) | |
\____/_| |_| \___/|_|
02:49:12: {ERROR:
There is a chance your target is in SAHARA mode!!
There is a chance your target is in SAHARA mode!!
There is a chance your target is in SAHARA mode!!
This can mean
1. You forgot to send DeviceProgrammer first (i.e. QSaharaServer.exe -s 13rog_emmc_firehose_8994_lite.mbn)
2. OR, you did send DeviceProgrammer, but it has crashed and/or is not correct for this target
Regardless this program speaks FIREHOSE protocol and your target is speaking SAHARA protcol, so this will not work
}
Writing log to 'C:\Users\Hans\AppData\Roaming\Qualcomm\QFIL\COMPORT_4\port_trace.txt', might take a minute
Log is 'C:\Users\Hans\AppData\Roaming\Qualcomm\QFIL\COMPORT_4\port_trace.txt'
Download Fail:FireHose Fail:FHLoader Failrocess fail
Finish Download
aidenskcyu said:
my phone stuck in corrupted recovery mode but i can still access edl mode. i can't flash another custom recovery and can't flash stock rom too, it always says:
Validating Application Configuration
Load APP Configuration
COM:4
PBLDOWNLOADPROTOCOL:0
PROGRAMMER:True
PROGRAMMER:E:\Installers\EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92\twrp\prog_emmc_firehose_652.mbn
RESETSAHARASTATEEMACHINE:False
SEARCHPATH:E:\Installers\EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92\twrp
RAWPROGRAM:
rawprogram0.xml
PATCH:
patch0.xml
ACKRAWDATAEVERYNUMPACKETS:False
ACKRAWDATAEVERYNUMPACKETS:100
MAXPAYLOADSIZETOTARGETINBYTES:False
MAXPAYLOADSIZETOTARGETINBYTES:49152
DEVICETYPE:eMMC
PLATFORM:8x26
VALIDATIONMODE:0
RESETAFTERDOWNLOAD:False
MAXDIGESTTABLESIZE:8192
SWITCHTOFIREHOSETIMEOUT:30
RESETTIMEOUT:200
RESETDELAYTIME:2
FLATBUILDPATH:C:\
FLATBUILDFORCEOVERRIDE:True
QCNPATH:C:\Temp\00000000.qcn
QCNAUTOBACKUPRESTORE:False
SPCCODE:000000
ENABLEMULTISIM:False
AUTOPRESERVEPARTITIONS:False
PARTITIONPRESERVEMODE:0
PRESERVEDPARTITIONS:0
PRESERVEDPARTITIONS:
ERASEALL:False
Load ARG Configuration
Validating Download Configuration
Image Search Path: E:\Installers\EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92\twrp
RAWPROGRAM file path: E:\Installers\EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92\twrp\rawprogram0.xml
PATCH file path:E:\Installers\EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92\twrp\patch0.xml
Programmer Path:E:\Installers\EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92\twrp\prog_emmc_firehose_652.mbn
Process Index:0
Start Download
Program Path:E:\Installers\EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92\twrp\prog_emmc_firehose_652.mbn
***** Working Folder:C:\Users\Hans\AppData\Roaming\Qualcomm\QFIL\COMPORT_4
Binary build date: May 13 2015 @ 14:41:37
QSAHARASERVER CALLED LIKE THIS: 'C:\Program Files (x86)\Qualcomm\QPST\bin\QSaharaServer.exe -u 4 -s 13:E:\Installers\EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92\twrp\prog_emmc_firehose_652.mbn 'Current working dir: C:\Users\Hans\AppData\Roaming\Qualcomm\QFIL\COMPORT_4
Sahara mappings:
2: amss.mbn
6: apps.mbn
8: dsp1.mbn
10: dbl.mbn
11: osbl.mbn
12: dsp2.mbn
16: efs1.mbn
17: efs2.mbn
20: efs3.mbn
21: sbl1.mbn
22: sbl2.mbn
23: rpm.mbn
25: tz.mbn
28: dsp3.mbn
29: acdb.mbn
30: wdt.mbn
31: mba.mbn
Sending Programmer Finished
Switch To FireHose
Wait for 3 seconds...
Max Payload Size to Target:49152 Bytes
Device Type:eMMC
Platform:8x26
Disable Ack Raw Data Every N Packets
Skip Write:False
Always Validate:False
Use Verbose:False
***** Working Folder:C:\Users\Hans\AppData\Roaming\Qualcomm\QFIL\COMPORT_4
Binary build date: Jun 3 2015 @ 17:12:06
Build version: 15.06. 3.17.12.06
02:49:12: INFO: FH_LOADER WAS CALLED EXACTLY LIKE THIS
************************************************
C:\Program Files (x86)\Qualcomm\QPST\bin\fh_loader.exe --port=\\.\COM4 --sendxml=rawprogram0.xml --search_path=E:\Installers\EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92\twrp --noprompt --showpercentagecomplete --zlpawarehost=1 --memoryname=emmc
************************************************
02:49:12: INFO: Current working dir (cwd): C:\Users\Hans\AppData\Roaming\Qualcomm\QFIL\COMPORT_4\
02:49:12: INFO: Showing network mappings to allow debugging
02:49:12: INFO:
02:49:12: INFO: Trying to store 'rawprogram0.xml' in string table
02:49:12: INFO: Looking for file 'rawprogram0.xml'
02:49:12: INFO: User wants to talk to port '\\.\COM4'
02:49:12: INFO: Took 0.01500000 seconds to open port
02:49:12: INFO: Sorting TAGS to ensure order is <configure>,<erase>, others, <patch>,<power>
02:49:12: INFO: If you don't want this, use --dontsorttags
02:49:12: INFO: Looking for file 'recovery.img'
02:49:12: INFO: Looking for file 'boot.img'
02:49:12: INFO:
Total to be tansferd with <program> or <read> is 35.30 MB
02:49:12: INFO: Sending <configure>
_____
| ___|
| |__ _ __ _ __ ___ _ __
| __| '__| '__/ _ \| '__|
| |__| | | | | (_) | |
\____/_| |_| \___/|_|
02:49:12: {ERROR: XML not formed correctly. Expected a < character at loc 0}
_____
| ___|
| |__ _ __ _ __ ___ _ __
| __| '__| '__/ _ \| '__|
| |__| | | | | (_) | |
\____/_| |_| \___/|_|
02:49:12: {ERROR: 3. TAG not found or recognized}
_____
| ___|
| |__ _ __ _ __ ___ _ __
| __| '__| '__/ _ \| '__|
| |__| | | | | (_) | |
\____/_| |_| \___/|_|
02:49:12: {ERROR:
There is a chance your target is in SAHARA mode!!
There is a chance your target is in SAHARA mode!!
There is a chance your target is in SAHARA mode!!
This can mean
1. You forgot to send DeviceProgrammer first (i.e. QSaharaServer.exe -s 13rog_emmc_firehose_8994_lite.mbn)
2. OR, you did send DeviceProgrammer, but it has crashed and/or is not correct for this target
Regardless this program speaks FIREHOSE protocol and your target is speaking SAHARA protcol, so this will not work
}
Writing log to 'C:\Users\Hans\AppData\Roaming\Qualcomm\QFIL\COMPORT_4\port_trace.txt', might take a minute
Log is 'C:\Users\Hans\AppData\Roaming\Qualcomm\QFIL\COMPORT_4\port_trace.txt'
Download Fail:FireHose Fail:FHLoader Failrocess fail
Finish Download
Click to expand...
Click to collapse
Since EDL mode is still accessible, try flashing EUI from MiFlash tool (EUI5.9 ZAXCNFN5902606201S can be flashed from this tool ) and get your device back up running.
nml_krishna said:
Since EDL mode is still accessible, try flashing EUI from MiFlash tool (EUI5.9 ZAXCNFN5902606201S can be flashed from this tool ) and get your device back up running.
Click to expand...
Click to collapse
hey thanks! can you give me some link to this EUI5.9 ZAXCNFN5902606201S rom? i can't find the right rom for miflash
edit: thanks dude it works! but the problem now is how can i flash twrp because it still giving same error in qfil
aidenskcyu said:
hey thanks! can you give me some link to this EUI5.9 ZAXCNFN5902606201S rom? i can't find the right rom for miflash
edit: thanks dude it works! but the problem now is how can i flash twrp because it still giving same error in qfil
Click to expand...
Click to collapse
Try Flashing the same EUI twrp through MiFlash tool.
Open MiFlash and browse to twrp folder in EUI_TWRP_6.0.1_V1_ADVANCED_CUOCO92 and connect device in EDL mode.
Once you see the device in MiFlash tool, click on Flash ( leave the flash all except storage checked ).
After flash is complete keep holding power + vol up button for twrp recovery. Hopefully this should fix corrupted twrp.
OR
If you have stock rom CPB file flashed through YGDP tool, follow below procedure to flash it through MiFlash
- Extract CPB file contents using CPB unpacker.
- Rename prog_emmc_firehose.mbn to prog_emmc_firehose_8976_ddr.mbn under the CPB extracted files
- Open MiFlash tool, browse to the CPB extracted folder.
- Connect device in EDL mode
- Click on Flash
Once the flash is complete, device should be able to boot to stock rom.