Does anyone know what happend to my phone...i can't enter recovery mode
imageshack.com/i/pnU6j9mTj
skyxstar77 said:
Does anyone know what happend to my phone...i can't enter recovery mode
imageshack.com/i/pnU6j9mTj
Click to expand...
Click to collapse
Can you access to system?
Did you tried to install TWRP?
And what was the main problem that you wanted to use recovery?
amirizad_7436 said:
Can you access to system?
Did you tried to install TWRP?
And what was the main problem that you wanted to use recovery?
Click to expand...
Click to collapse
I already upload picture..u can check link.
amirizad_7436 said:
Can you access to system?
Did you tried to install TWRP?
And what was the main problem that you wanted to use recovery?
Click to expand...
Click to collapse
When i press power button,on my screen show
ODIN MODE
PRODUCT NAME : SM-J500G
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
FRP LOCK: Off
WARRANTY VOID: 0x1 (4)
QUALCOMM SECUREBOOT: ENABLE (CSB)
RP SWREV: S1, T1, H1, R1, A1, P1
SECURE DOWNLOAD : ENABLE
skyxstar77 said:
When i press power button,on my screen show
ODIN MODE
PRODUCT NAME : SM-J500G
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
FRP LOCK: Off
WARRANTY VOID: 0x1 (4)
QUALCOMM SECUREBOOT: ENABLE (CSB)
RP SWREV: S1, T1, H1, R1, A1, P1
SECURE DOWNLOAD : ENABLE
Click to expand...
Click to collapse
Ok
Would you please answer my questions?
And what did you do to display this one?
Related
hey everyone.
i have red hundreds of threads on this put when i start up my phone it says:
Could not do normal boot
ODIN MODE
PRODUCT NAME: GT-I9506
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x1
QUALCOMM SECUREBOOT: ENABLE
RP SWREV: S1, T1, R1, A1, P1
WRITE PROTECTION: ENABLE
UDC Start
i have tried to pull out the battery and the sim card. it didn't work
i have tried reinstalling the stock firmware with odin3 v1.85
i have tried the same with samsung kies 3 it doesn't even recognise (sorry if mispelled) the device
please help
last but not least. does this means my warranty wont work?
i sometimes get an 'error' message rebooting my phone (either directly or to/from twrp)
i think it first occured after i flashed twrp
i'm running on cm12 (nightly)
the full text reads:
boot recovery mode
check boot partitions. .
sbl1 partition doesn't exist
odin mode
product name: sm-g900f
current binary: custom
sytem status: custom
reactivation lock(kk): off
knox warranty void: 0x1 (0)
qualcomm secureboot: enable (csb)
rp swrev: s1, t1, r1, a1, p1
secure download : enable
udc start
if i then press the power button for ten seconds, the system boots without a problem
still, i don't like this
i tried solving this problem by going back to stock
also flashed the pit file for my device (g900f)
didn't help
what's wrong and what should i do?
scienex said:
i sometimes get an 'error' message rebooting my phone (either directly or to/from twrp)
i think it first occured after i flashed twrp
i'm running on cm12 (nightly)
the full text reads:
boot recovery mode
check boot partitions. .
sbl1 partition doesn't exist
odin mode
product name: sm-g900f
current binary: custom
sytem status: custom
reactivation lock(kk): off
knox warranty void: 0x1 (0)
qualcomm secureboot: enable (csb)
rp swrev: s1, t1, r1, a1, p1
secure download : enable
udc start
if i then press the power button for ten seconds, the system boots without a problem
still, i don't like this
i tried solving this problem by going back to stock
also flashed the pit file for my device (g900f)
didn't help
what's wrong and what should i do?
Click to expand...
Click to collapse
Could be an emmc failure.. But I'm sorry to be late to the post
thnx mate!
it's four phones ago
but i appreciate your reply :good:
scienex said:
thnx mate!
it's four phones ago
but i appreciate your reply :good:
Click to expand...
Click to collapse
Absolutely boss!
It says:
Could not do normal boot.
ODIN MODE
PRODUCT NAME:SM-N900S
CURRENT BINARY:CUSTOM
SYSTEM STATUS:CUSTOM
REACTIVATION LOCKFF
KNOW WARRANTY VOID: 0X1 4
QUALCOMM SECUREBOOT: ENABLE CSB
RP SWREV: S2,T2,A2,A4,P2
SECURE DOWNLOAD:ENABLE
UDC START
How it happened:I just rooted my phone so i can install a rom on my sm-n900s but i didnt realise that it was for an sm-n900.I flashed it on my phone with flashify and now all i can do is go to my custom recovery TWRP to wipe everything but still to no avail.I really do not know what to do.PLS HELP :crying::crying::crying::crying::crying:
Look for a stock rom on sammobile.com. If you find it, flash it via Odin.
Btw, no need to root before installing a custom rom or recovery.
OMG MY PHONE WORKED.I used a stock rom and it worked although it booted up very slow.THANK YOU SO MUCH.
Could not do normal boot.
ODIN MODE
PRODUCT NAME:SM-N900S
CURRENT BINARY:SAMSUNG OFFICIAL
SYSTEM STATUS:CUSTOM
REACTIVATION LOCKFF
KNOW WARRANTY VOID: 0X1 4
QUALCOMM SECUREBOOT: ENABLE CSB
RP SWREV: S2,T2,A2,A4,P2
SECURE DOWNLOAD:ENABLE
UDC START
Could not do normal boot.
ODIN MODE
PRODUCT NAME:SM-N900L
CURRENT BINARY:CUSTOM
SYSTEM STATUS:CUSTOM
REACTIVATION LOCKFF
KNOW WARRANTY VOID: 0X0
QUALCOMM SECUREBOOT: ENABLE CSB
RP SWREV: S2,T2,A2,A4,P2
SECURE DOWNLOAD:ENABLE
UDC START.
please help
yes bro
saiful aslam said:
Could not do normal boot.
ODIN MODE
PRODUCT NAME:SM-N900L
CURRENT BINARY:CUSTOM
SYSTEM STATUS:CUSTOM
REACTIVATION LOCKFF
KNOW WARRANTY VOID: 0X0
QUALCOMM SECUREBOOT: ENABLE CSB
RP SWREV: S2,T2,A2,A4,P2
SECURE DOWNLOAD:ENABLE
UDC START.
please help
Click to expand...
Click to collapse
www.samsony.com
enter this link go go go
Ive tried everything. I tried flashing with odin and kiesI need to do an emergency firmware recovery on my SM-N910T phone. I have a new pc so I do not have the code. How to I obtain a new one so I can update my firmware.
This is what it says..
ddi : mmc_read failed
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-N910T
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
REACTIVATION LOCK: OFF
KNOX WARRANTY VOID: 0x1 (0)
QUALCOMM SECUREBOOT: ENABLED (CSB)
RP SWREV: S1, T1, R1, A2, P1
SECURE DOWNLOAD: ENABLE
UDC START
Then it tells me to use Kies to do a firmware recovery. I cant do an emergency recovery because I dont have the recovery code. Odin fails everytime I try to flash anything on it. Please help ....
dwaynelegg said:
Ive tried everything. I tried flashing with odin and kiesI need to do an emergency firmware recovery on my SM-N910T phone. I have a new pc so I do not have the code. How to I obtain a new one so I can update my firmware.
This is what it says..
ddi : mmc_read failed
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-N910T
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
REACTIVATION LOCK: OFF
KNOX WARRANTY VOID: 0x1 (0)
QUALCOMM SECUREBOOT: ENABLED (CSB)
RP SWREV: S1, T1, R1, A2, P1
SECURE DOWNLOAD: ENABLE
UDC START
Then it tells me to use Kies to do a firmware recovery. I cant do an emergency recovery because I dont have the recovery code. Odin fails everytime I try to flash anything on it. Please help ....
Click to expand...
Click to collapse
PM me...I found a fix for this.
Hello , xda-developers,
I have a SM-N910F, and "played" today with the ROM and recovery, trying to root and put a custom recovery.
The Odin part worked smoothly, changed a couple of times the ROM but not succeeding the part with recovery.
After a wrong file being flashed (n915f-cwm-recovery-6.0.5.1(1128)), the screen mistakes the position of my finger onto screen.
Tried flashing stock ROM for it (COA-N910FXXU1ANK4_N910FCOA1ANK1-20141117 -Android 4.4.4 and N910FXXU1DRI2_N910FCOA1DQI1_COA - Android 6.0.1 ),no luck.
Screen not recognise corectly whereis my finger on screen, but the stilus work perfect, also mouse with OTG seems to work fine.
What is to be done to revert this.
Can be fixable?
THX!
find the solution on "https://www.youtube.com/watch?v=eAyZAa8ck8U" sorry for bother, although I would like to resolve the problem with the custom recovery and rooted with Magisk, what are the RIGHT steps
In IDIN mode I have on screen:
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-N910F
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
REACTIVATION LOCK: OFF
KNOX WARRANTARY VOID: 0x1 (4)
QUALCOM SECUREBOOT: ENABLE (CSB)
RP SWREV: S1, T1, R1, A1, P1
SECURE DOWNLOAD : ENABLE
UDC START
MasterMarius said:
find the solution on "https://www.youtube.com/watch?v=eAyZAa8ck8U" sorry for bother, although I would like to resolve the problem with the custom recovery and rooted with Magisk, what are the RIGHT steps
In IDIN mode I have on screen:
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-N910F
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
REACTIVATION LOCK: OFF
KNOX WARRANTARY VOID: 0x1 (4)
QUALCOM SECUREBOOT: ENABLE (CSB)
RP SWREV: S1, T1, R1, A1, P1
SECURE DOWNLOAD : ENABLE
UDC START
Click to expand...
Click to collapse
Open dialer and Dial *#2663#
Press TSP FW UPDATE
Wait until it finished
Reboot device
Done.
This will recalibrate your touch as normal to default.