Downgrade from stock Pie to Oreo using Odin failed - Samsung Galaxy Tab S3 Guides, News, & Discussion

Hi all,
after a long wait Samsung released the first update to Pie for Tab S3 SM-T825 on december 2019 (ITV-T825XXU3CSK2-20191226114137); I hoped it would fix most issues I experienced since I had upgraded from Oreo, but it's still sluggish, battery life is much worse and I don't find anything better than Oreo in this release... the worst Android build I've ever seen!
I finally decided to downgrade, so I downloaded the latest Oreo version available for my region (ITV-T825XXU3BSD1-20190510143544) and Odin v3.13.3.
AFAIK everything should work fine because the bootloader for both ROMs is the same version (XXU3); I followed the standard instructions available on Sammobile: launched Odin, selected BL, AP, CP, CSC and hit Start.
The flashing process starts without problems but it fails after a few minutes while the device is downloading system.img. Tried several times but to no avail.
The device had usb debug on, in download mode I see FRP lock on, OEM lock on.
Can anyone please help? Below you can find the Odin log.
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1303)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 5116 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> emmc_appsboot.mbn
<ID:0/005> lksecapp.mbn
<ID:0/005> xbl.elf
<ID:0/005> tz.mbn
<ID:0/005> hyp.mbn
<ID:0/005> devcfg.mbn
<ID:0/005> pmic.elf
<ID:0/005> rpm.mbn
<ID:0/005> cmnlib.mbn
<ID:0/005> keymaster.mbn
<ID:0/005> apdp.mbn
<ID:0/005> msadp.mbn
<ID:0/005> cmnlib64.mbn
<ID:0/005> sec.dat
<ID:0/005> NON-HLOS.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Never mind, it finally worked!
I put the device in recovery mode, wiped cache and user data, then repeated the flash process with Odin and everything went fine.

Hello , can you please share the firmware , it will be a a good will as it takes ages to download from sam firmware.com , you can give me a google drive link , god bless !

Related

My note 3 failed during odin firmware update to KitKat 4.4.2

Now I can’t install firmware or go into recovery mode but I can still get to download screen.
okizen said:
Now I can’t install firmware or go into recovery mode but I can still get to download screen.
Click to expand...
Click to collapse
Cant you go to the download screen and set ODIN away again?
Thats how I did it.
trubster said:
Cant you go to the download screen and set ODIN away again?
Thats how I did it.
Click to expand...
Click to collapse
Hi trubster, I've reset odin and my phone into download mode several times. The odin update process starts off ok but always fails when it reaches 'SYSTEM'.
okizen said:
Hi trubster, I've reset odin and my phone into download mode several times. The odin update process starts off ok but always fails when it reaches 'SYSTEM'.
Click to expand...
Click to collapse
What message is ODIN giving in the white text box?
have you tried re-downloading the ROM? I used the MEGA link and it worked fine.
N9005XXUENA6_N9005OXXENA5_XEO.zip is the one you need if it is for the N9005, you need the stock 4.4.2 FW before you can put CFW on
trubster said:
What message is ODIN giving in the white text box?
have you tried re-downloading the ROM? I used the MEGA link and it worked fine.
N9005XXUENA6_N9005OXXENA5_XEO.zip is the one you need if it is for the N9005, you need the stock 4.4.2 FW before you can put CFW on
Click to expand...
Click to collapse
These are the messages I get from odin (from the beginning).
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUENA6_N9005OXXENA5_N9005XXUENA2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
I should also mention that I has tripped my Knox to 0x1as I've always got on without one but I doubt if that would be the cause.
That file seems to be different, are you using a N9005?
https://mega.co.nz/#!jZYkyY5a!HfiJlXRgp_ZGWoQncFNWeEn5FnY_0i9iFb23EGfg2Nk
Thats the file I used first, put it in the PDA or AP box on odin and click start.
Should have no problems with it as it is an "Official" Sammy Rom
If you have a Hong Kong note you need to have a read around, If not, grab XEO firmware flash via odin 1.85 or 3.07
trubster said:
That file seems to be different, are you using a N9005?
https://mega.co.nz/#!jZYkyY5a!HfiJlXRgp_ZGWoQncFNWeEn5FnY_0i9iFb23EGfg2Nk
Thats the file I used first, put it in the PDA or AP box on odin and click start.
Should have no problems with it as it is an "Official" Sammy Rom
Click to expand...
Click to collapse
Sorry trubster, I missed out a part of the message in odin.
This is the FULL message in it's entirety.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUENA6_N9005OXXENA5_N9005XXUENA2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
I've also tried the firmware from your link but unfortunately the results were the same.
I didn't experience this on my N9005 while updating, but I experienced this before on my S3, it was due to corrupted firmware file.
Please help me!!! Please!!!
okizen said:
sorry trubster, i missed out a part of the message in odin.
This is the full message in it's entirety.
<osm> enter cs for md5..
<osm> check md5.. Do not unplug the cable..
<osm> please wait..
<osm> n9005xxuena6_n9005oxxena5_n9005xxuena2_home.tar.md5 is valid.
<osm> checking md5 finished sucessfully..
<osm> leave cs..
<id:0/003> added!!
<id:0/003> odin v.3 engine (id:3)..
<id:0/003> file analysis..
<id:0/003> setupconnection..
<id:0/003> initialzation..
<id:0/003> get pit for mapping..
<id:0/003> firmware update start..
<id:0/003> aboot.mbn
<id:0/003> nand write start!!
<id:0/003> sbl1.mbn
<id:0/003> rpm.mbn
<id:0/003> tz.mbn
<id:0/003> sdi.mbn
<id:0/003> non-hlos.bin
<id:0/003> boot.img
<id:0/003> recovery.img
<id:0/003> system.img.ext4
<id:0/003> complete(write) operation failed.
<osm> all threads completed. (succeed 0 / failed 1)
<id:0/003> removed!!
<id:0/003> added!!
<id:0/003> removed!!
I've also tried the firmware from your link but unfortunately the results were the same.
Click to expand...
Click to collapse
i am also having this problem
it seems i cant flash other firmware other than poland fw...
I want ro revert back to ksa firmware or anygood fw since poland svoice isnt working fine<< sorry for bag english
please help me
i have flash my fw with kk italy, and spain but to luck,,, still having the same result... Failed!!!
Please please
u have to download hungry firmwar from sammobiles.com..it will b ok.and tick update boot loader must
clowrid1128 said:
i am also having this problem
it seems i cant flash other firmware other than poland fw...
Click to expand...
Click to collapse
I had the same problem... Just try to flash with this version of ODIN:
https://mega.co.nz/#!RVVXSYiY!6lynzTh-II8o8rvfYkdZzrYa_7m2F-CKgtItMZA66v4
I had the same problem today.The solution is here http://www.cultofandroid.com/53963/save-galaxy-note-3-failed-kitkat-update-odin-tip/
Now i am with german kit kat (DBT) and everything is ok !!!!!! :good::good::good:
Help me (SAM SM-N900S)
<ID:0/023> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_N900SKSU0GPI1_CL9178490_QB10835717_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_N900SKSU0GPI1_CL9178490_QB10835717_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_SKT_N900SSKT0GPI1_CL9178490_QB10835717_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_N900SKSU0GPI1_CL9178490_QB10835717_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/023> Removed!!
<ID:0/028> Added!!
<ID:0/028> Odin engine v(ID:3.1005)..
<ID:0/028> File analysis..
<ID:0/028> SetupConnection..
<ID:0/028> Initialzation..
<ID:0/028> Set PIT file..
<ID:0/028> DO NOT TURN OFF TARGET!!
<ID:0/028> FAIL!
<ID:0/028>
<ID:0/028> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/028> Removed!!
<ID:0/028> Added!!
<ID:0/028> Odin engine v(ID:3.1005)..
<ID:0/028> File analysis..
<ID:0/028> SetupConnection..
<ID:0/028> Initialzation..
<ID:0/028> Set PIT file..
<ID:0/028> DO NOT TURN OFF TARGET!!
<ID:0/028> FAIL!
<ID:0/028>
<ID:0/028> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/028> Removed!!
:crying:
Why are you flashing Kitkat ??
What phone have you got and what have you done before .
PIT showing as no partition fail .

Odin3 Error | Note 4

Hi,
I am trying to go back android 5 from 6. So I download the custom 5.1.1 rom. But odin keeps failing. ( Usb driver is fine. )
Galaxy Note 4 SM-910CQ - 32GB
HTML:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1101)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
I have the same problem. Mine stops at system.ext4 write.
we both need help pls guys
I need help too,
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Hi friends, I just figured it out....
What you need to do is Download the Stock 6.0.1 Rom from SamMobile and flash it thru Odin, and that's it !!
Hope this works for you as worked for me!
5
Thank you for respond but I am not asking for 6.0.1 Rom
I want to go back to Android 5 from 6.
You cannot flash a custom ROM with ODIN . Use TWRP for that. And for going back to Lollipop, you need to flash a suitable Bootloader and Modem first.
looks like I need to google it...
what about cyanogenmode ? anyone of you used it before (note4)
opticon107 said:
I need help too,
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Click to expand...
Click to collapse
I just f,gured it by myself.
dont flash the 1st file from odin only flash the file

S7 edge Odin Fail

Help me please, already tried to look into different threads but can't find a solution. Here's Odin log after fail.
Already tried different rom version and Odin versions aswell...Don't knot what to do!!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> skip file list for home binary
<ID:0/005> param.bin
<ID:0/005> Home Binary Download
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> modem.bin
<ID:0/005> Transmission Complete..
<ID:0/005> Now Writing.. Please wait about 2 minutes
<ID:0/005> Receive Response from boot-loader
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> RQT_CLOSE !!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
COmplement
Guys, really cant find any solution. I'l try to reset the stock AP, already downloading it.
Other than that, I don't know what to do!!!:crying:
Hi
We have a forum for your device(S7 Edge).
If you post in the Q&A thread(link provided below), I'm sure you'll receive help there
http://forum.xda-developers.com/s7-edge/help
Good luck

G900F Won't boot to ROM or Recovery

This all started when I tried to flash Clockwork recovery on my stock G900F. I used Odin to successfully load the recovery, but as soon as it booted it would get stuck at "Set warranty bit: recovery" and restart itself into the ROM. So then I tried TWRP and Philz Touch and got the same thing. Then I tried to flash CF-Auto Root to see if I could use root permissions to restart into recovery via the CWM app, but that too gave me the same error. I tried both with and without Auto-Reboot on to see if maybe the stock ROM was overwriting the recovery but that didn't fix it either. This entire time USB debugging was enabled so that's not it.
Since the point of me doing this was to install CM 14.1 anyways, I decided to try flashing a stock ROM. I tried a whole bunch of different rips and none of them worked. The ones that were compressed into .tar would give the following error in Odin:
Code:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1203)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> aboot.mbn
<ID:0/006> FAIL! (Auth)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
The one that was broken into four separate files gives this error:
Code:
<ID:0/006> Odin engine v(ID:3.1203)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
For both types of rips I had both Auto-Boot and F. Reset Time on. I did once attempt to use the .pit file provided with the latter rip and attempt to re-format, but that didn't do anything except prevent my stock ROM from booting (it's now stuck at the Samsung logo). I can still boot into download mode.
What are my options from here? I'm a little disheartened that my stock phone was unable to load any of the recovery tools that I tried, but maybe I'm missing something.
I tried using the firmware linked in this thread. I tried flashing with both T-flash and repartition as well as just T-flash and it doesn't work.
I get about halfway through the download before it fails. This is the output from Odin:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> T Flash...
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> sbl1.mbn
<ID:0/004> rpm.mbn
<ID:0/004> tz.mbn
<ID:0/004> sdi.mbn
<ID:0/004> NON-HLOS.bin
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> persist.img.ext4
<ID:0/004> userdata.img.ext4
<ID:0/004> FAIL! (Erase)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I can still boot into download mode and successfully flash any recovery I try, but I also still can't boot into recovery. Any help is greatly appreciated.
Turns out this was as simple as not having the version of the phone I thought I had.
Amazon told me it was a G900F when I bought it. The box says G900F. The sticker beneath the battery says G900F. The phone itself says G9006V.
When I searched to see if this has happened to anyone else, I saw more than a few confused and frustrated people learning this same thing the hard way as I did.
The lesson here is to trust what you see in download mode and disregard everything else. It's a bit slimy, but that's the world we live in.

HELPPPP! flash error

hi. i screwed up in trying to root my phone thinking it would be an easy process like i had when i had jailbroken my old iphones....nope
Im pretty sure i have the stock firmware files. if someone can link me a download for the SM-G935v firmware with marshellow would be awseome too.
when trying to flash i am getting a fused 3 > binary 1 message on my phone
odin says:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> skip file list for home binary
<ID:0/005> persist.img.ext4
<ID:0/005> Home Binary Download
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
my phone says :
product name: sm-g935t
currenr binary: official
system status: official
fap lock: on
warrently void: 0x0
It is because you forgot to enable OEM unlocking, and now you have FRP lock, but don't worry, you just have to flash stock ROM again using odin ( download firmware from Sammobile ).
And next tine time you try to root, do not forget to enable OEM unlocking in developers menu.

Categories

Resources