Related
I'm installing the new firmware but i had an issue with odin...
I flashed again 4.4.2 but in download mode, the last line you can see " UDC START" in colour red... Is this normal? I think the phone works good, but i don't know why put on this...
Anyone have this new line??
I have the same problem with a N9005 I guess it was Hong Kong version for the kanjis in the back, but is stuck in odin mode with the UDC START line
UDC Start info.
Ok gent's little more knowledge about "udc start" I am guessing that the problem became clear as you installed 4.4.2 KK.
So did I and came across UDC Start the second time I booted into download mode.
As I played around i became aware that the "UDC Start" mode locks the download loader to certain criteria. This would be 4.4.2 KK,
so anything under 4.4.2 will get a MASSIVE RED FAIL. That including the CWR/TWRP recoveries and ROOT files.
So just to specify, yes phone is now locked/bricked to 4.4.2 KK software only.
Therefore I would please like some help to get the udc start away!? If anyone can help.
If I shared some light to the darkness please say thanks.:good:
Try this out:
Worked for me on a Hong Kong 16GB N9005 which was stuck on the 'Samsung Galaxy Note 3' screen after getting a 'Invalid: ext4 image' or 'Repartioning failed' errors while installing 4.4.2 OFFICIAL (Single File ROM) via Odin.
Binary: Custom
Knox: 0x1
Method:
In Odin mode
1. Flash the latest cf-autoroot (Kitkat support) [http://download.chainfire.eu/352/CF-...x-smn9005.zip]
2. Flash the Chenglu's latest CWM - 6.0.4.6 (the one that supports KitKat) http://forum.xda-developers.com/show....php?t=2454079
Download Sweet Rom and place it in ExtSDcard (http://forum.xda-developers.com/show....php?t=2487425)
I tried external sd-card with various format and could not install the ROM. After format my SD Card to FAT32, the ROM can be installed.
On Device
1. Boot in to Recovery mode by Volume up + Home + Power
2. Wipe Factory reset / Dalvik Cache
3. Format /System (under "mount and storage" menu) [IMPORTANT STEP]
4. Install Rom from SD Card
5. Say your prayer. You'll need it. (The installation could take sometimes. If the device screen shows Samsung boot animation, you're half way there)
How is that going to take away the udc start?
I have UDC Start in Odin/Download mode... It hasn't affected my flashing of custom ROMs nor Stock, everyone on KK has it.
Ok, but why if i try to install a previous version of TW rom 4.3 i get a massive fail?
But all the rest works?
Thanx in regards.
FdeKlerk said:
Ok, but why if i try to install a previous version of TW rom 4.3 i get a massive fail?
But all the rest works?
Thanx in regards.
Click to expand...
Click to collapse
Because you are locked into the new Bootloader (NA6) and it's unable to downgrade
So I am guessing there is no way to downgrade the boot-loader without unlocking it?
FdeKlerk said:
So I am guessing there is no way to downgrade the boot-loader without unlocking it?
Click to expand...
Click to collapse
There's no way full stop. Samsung have blocked downgrades within the bootloader itself.
Wow now that's some sort of a problem.
My 4.4.2 works but i love xposed modules to make everything transparent and as of yet kitkat does not support that.
And now i a stuck on 4.4.2..
But thanx for the assist.:good:
Same Problem with E330s
ManuH8 said:
I'm installing the new firmware but i had an issue with odin...
I flashed again 4.4.2 but in download mode, the last line you can see " UDC START" in colour red... Is this normal? I think the phone works good, but i don't know why put on this...
Anyone have this new line??
Click to expand...
Click to collapse
Hi. I have a unrooted SHV-E330 (I9506 to some) I was running the unrooted firmware and updating with Kies up until yesterday when the update to came up. I ran it as with every other update however on self rebooting the phone now goes to ODIN MODE (in red) and UDC Start (in red) i'm a root virgin and was happy with the phone running as it was AnTU TU score 36118 with the Korean bloatware running in the background. From what I have picked up after 4.3 firmware update to 4.4.2 there is no going back. I tired to root with earlier versions of firmware but get fail every time. I Picked up a zip SKT-E330SKSUCNA7 wich goes as far as checking the MD5 file successfully in Odin 3 v3.09. everywhere I look on the web it states the com box should be yellow however mine is blue.
After MD5 successful I get leave CS. I click start I get 'Get PIT for mapping. There id no PIT partion followed by a red box and the'FAIL!' box with 'all threads completed Failed 1.
I have never rooted a phone and a buff mentioned that I will not regret it. I figure thart i'm doing something wrong as there was no PIT file with the firmware.
On first trying a firmware recovery in Kies because the phone is stuck In ODIN MODE it will not recognise the phone even though the USB drivers are installed.
If their is a person out there that could talk me through rooting trough the stuck ODIN MODE I would appreciate contact.
I gather that I have no choice but to try ODIN MODE on phone as that's where the phone is stuck. Removing battery etc has been tried to death.
summan971 said:
Hi. I have a unrooted SHV-E330 (I9506 to some) I was running the unrooted firmware and updating with Kies up until yesterday when the update to came up. I ran it as with every other update however on self rebooting the phone now goes to ODIN MODE (in red) and UDC Start (in red) i'm a root virgin and was happy with the phone running as it was AnTU TU score 36118 with the Korean bloatware running in the background. From what I have picked up after 4.3 firmware update to 4.4.2 there is no going back. I tired to root with earlier versions of firmware but get fail every time. I Picked up a zip SKT-E330SKSUCNA7 wich goes as far as checking the MD5 file successfully in Odin 3 v3.09. everywhere I look on the web it states the com box should be yellow however mine is blue.
After MD5 successful I get leave CS. I click start I get 'Get PIT for mapping. There id no PIT partion followed by a red box and the'FAIL!' box with 'all threads completed Failed 1.
I have never rooted a phone and a buff mentioned that I will not regret it. I figure thart i'm doing something wrong as there was no PIT file with the firmware.
On first trying a firmware recovery in Kies because the phone is stuck In ODIN MODE it will not recognise the phone even though the USB drivers are installed.
If their is a person out there that could talk me through rooting trough the stuck ODIN MODE I would appreciate contact.
I gather that I have no choice but to try ODIN MODE on phone as that's where the phone is stuck. Removing battery etc has been tried to death.
Click to expand...
Click to collapse
Your phone does not have a pit file on it. Odin downloads the pit file from the phone to make sure that all the partitions are correctly flashed.
Try ticking the 'Re-partition' box in odin while flashing. Though I don't really think it will help, because your single file ROM most probably does not contain the pit.
Your best bet is to find somebody else with the same model as you, and get a pit from them.
PS- You are in the wrong forums.
[COLOR=[/COLOR]
feralfire said:
your phone does not have a pit file on it. Odin downloads the pit file from the phone to make sure that all the partitions are correctly flashed.
Try ticking the 're-partition' box in odin while flashing. Though i don't really think it will help, because your single file rom most probably does not contain the pit.
Your best bet is to find somebody else with the same model as you, and get a pit from them.
Ps- you are in the wrong forums.
Click to expand...
Click to collapse
do not tick re-partition without having a pit file, you will get a brick.
Feralfire, you just broke the first law of flashing with ODIN... If you don't know what to do then don't say anything...
Thanks for caring XDA developers - i fixed it
FeralFire said:
Your phone does not have a pit file on it. Odin downloads the pit file from the phone to make sure that all the partitions are correctly flashed.
Try ticking the 'Re-partition' box in odin while flashing. Though I don't really think it will help, because your single file ROM most probably does not contain the pit.
Your best bet is to find somebody else with the same model as you, and get a pit from them.
PS- You are in the wrong forums.
Click to expand...
Click to collapse
Hey thanks for the response the same day I managed to fix the problem a hour ago after 24 hours of banging my head on a wall.
I uninstalled all software including Odin remembering that ODIN MODE was the only option. most of the Boot Operating system was in Korean.
I followed a you tube guide from another root and noticed that although ODIN MODE and UDC start are new (according to other forums) that the other information insinuated that the screen I was looking at was also the download mode.
I reinstalled Kies and rather than asking me for the emergency recovery code it reset and was asking for the Model and serial number. After which it stated it could not recover the device only reinstall the stock firmware. I selected OK. the phone came back to life and reinstalled all data from cloud.
now on 4.4.2 and still thinking about rooting
however I must warn anyone that comes across the unlocker website that states its mod allows for E330S root. that clockwork mod does not cater for E330S.
ultramag69 said:
[COLOR=[/COLOR]
do not tick re-partition without having a pit file, you will get a brick.
Feralfire, you just broke the first law of flashing with ODIN... If you don't know what to do then don't say anything...
Click to expand...
Click to collapse
Au contraire, I have done a lot of research on pit file and played around a lot. Check out my threads.
If you tick re-partition without having a pit, it just gives you an error. Maybe in the olden days, it might have been an issue (I haven't always been a Samsung guy), but definitely not now.
FeralFire said:
Au contraire, I have done a lot of research on pit file and played around a lot. Check out my threads.
If you tick re-partition without having a pit, it just gives you an error. Maybe in the olden days, it might have been an issue (I haven't always been a Samsung guy), but definitely not now.
Click to expand...
Click to collapse
If so, then make sure they know which version of ODIN to use as this is the fastest way to kill a phone I know...
Right from the very first this was a cardinal sin but then you didn't have a phone anymore or much sympathy either... But to tell a noob to do this was in effect saying "put your phone in front of a steamroller, it'll be ok after its gone over it a couple of times"...
ultramag69 said:
If so, then make sure they know which version of ODIN to use as this is the fastest way to kill a phone I know...
Right from the very first this was a cardinal sin but then you didn't have a phone anymore or much sympathy either... But to tell a noob to do this was in effect saying "put your phone in front of a steamroller, it'll be ok after its gone over it a couple of times"...
Click to expand...
Click to collapse
He was using 3.09. Don't overcomplicate things.
But anyway, I apologize for making people put their phones in front of 20 ton vehicles.
re Pit File
FeralFire said:
Your phone does not have a pit file on it. Odin downloads the pit file from the phone to make sure that all the partitions are correctly flashed.
Try ticking the 'Re-partition' box in odin while flashing. Though I don't really think it will help, because your single file ROM most probably does not contain the pit.
Your best bet is to find somebody else with the same model as you, and get a pit from them.
PS- You are in the wrong forums.
Click to expand...
Click to collapse
I found this KS01LTE_KOR_SKT_32G.pit and ran it in Odin running download mode and it worked. It appears there are several Korean versions of the right ROM and unless the right rom is used flash in odin does not work.
I'm starting to sound like i know what i'm talking about!
summan971 said:
I found this KS01LTE_KOR_SKT_32G.pit and ran it in Odin running download mode and it worked. It appears there are several Korean versions of the right ROM and unless the right rom is used flash in odin does not work.
I'm starting to sound like i know what i'm talking about!
Click to expand...
Click to collapse
The different ROMs must have different pits. That would explain why only some specific ones work.
Anyway, congratulations.
I get model mismatch every single time, I have downloaded the right firmware.. Downloaded the one said to do 5 DIFFERENT ONES that are all essentially the same, I rooted succesffully, then tried to flash xposed and failed obv.
.."Stock-S7-EDGE-ATT_G935AATT2APG1.zip"
"AP_G935AUCS2APF2_CL7617530_QB9897831_REV02_user_low_ship_MULTI_CERT.tar.md5"
Etc. Idk what to do anymore, stuck in download or recovery mode.
"Downloaded the one said to do 5 DIFFERENT ONES that are essentially the same," what does that mean? You downloaded the firmware zip file that had 5 seperate files in it, and they're all essentially the same? See how you quoted one of the files inside? Notice how it starts with "AP"? In odin, you click the AP button, then add that file in that AP slot. Then the one that starts with "BL" in the BL slot, and so on and so forth, until you have all 5 files in their respective slots. THEN you start the flashing process. Did you do that? If that didn't work, did you make sure the md5 number listed at the download screen match after you downloaded the zip file? Do you have an md5 checksum program on your computer? You can easily find a free one by doing a quick google search. You could also maybe try downloading and flashing a different/newer stock AT&T firmware.
As for xposed, you first need to download and install this version of the xposed apk from the xposed website: XposedInstaller_3.0_alpha4.apk
Then, if/when rooted find and flash this version of xposed framework in flashfire:
xposed-v85.1-sdk23-arm64-custom-build-by-wanam-20160530.zip
If you're not having any luck, and your phone is still stuck in download or recovery mode, you can still power it off for the time being using the following steps:
If it's in recovery mode, you'll have options listed, like "reboot system now," and, "power off device." You can toggle through each choice using the volume up and down buttons, and once you highlight the one you want, hit the power button to select it. You can go to "power off device" in recovery mode and turn your phone off for now if you don't want to have to worry about it. If your phone is in download mode, it'll either be at the warning screen where you can hit volume up to continue, or volume down to cancel and restart the phone. If it is all the way in download mode, it'll say "downloading... do not turn off target !!" If it is on the warning screen, just continue into into download mode. If it is in download mode already, or you just continued into download mode, and you want to turn the phone off, press and hold volume up, volume down, power, and home button and hold them all down at the same time until the phone shuts off. Immediately after, let go of all the buttons, and then press and hold the volume up, home, and power buttons until the phone comes back on, and in the top left corner, in blue, it'll say "Recovery booting." It is then that you let go of all the buttons. You will enter recovery there and be able to power the device off.
Anyway, I hope you already got it fixed, and if not, I hope this information helped. I'm not trying to be mean, but you really need to search through all of the forums, read everything, read people's comments for information on how to do these sort of things properly, and how to fix the problems. Rooting, installing custom roms and xposed is a little different on newer devices now. Mistakes can be much more costly now than they used to be, so unless you've read thoroughly on such processes, and/or have found a youtube video that helps and you're feeling confident about it, you might want to reconsider attempting to apply these kinds of changes to your phone. If you have any friends that are good at this stuff, maybe that would be another way as well. Anyway, best of luck to you.
Try Odin 3.12.3 or PrinceComsy version It work for me. My case was that I upgrade to the firmware 935u version bootloader v4 and I wanted go back to PH1 that the bootloader is v2. Make sure to do factory reset before do any flash with odin (I don't know if that matter but works for me). Hope this work for you.
xjimmy said:
"Downloaded the one said to do 5 DIFFERENT ONES that are essentially the same," what does that mean? You downloaded the firmware zip file that had 5 seperate files in it, and they're all essentially the same? See how you quoted one of the files inside? Notice how it starts with "AP"? In odin, you click the AP button, then add that file in that AP slot. Then the one that starts with "BL" in the BL slot, and so on and so forth, until you have all 5 files in their respective slots. THEN you start the flashing process. Did you do that? If that didn't work, did you make sure the md5 number listed at the download screen match after you downloaded the zip file? Do you have an md5 checksum program on your computer? You can easily find a free one by doing a quick google search. You could also maybe try downloading and flashing a different/newer stock AT&T firmware.
As for xposed, you first need to download and install this version of the xposed apk from the xposed website: XposedInstaller_3.0_alpha4.apk
Then, if/when rooted find and flash this version of xposed framework in flashfire:
xposed-v85.1-sdk23-arm64-custom-build-by-wanam-20160530.zip
If you're not having any luck, and your phone is still stuck in download or recovery mode, you can still power it off for the time being using the following steps:
If it's in recovery mode, you'll have options listed, like "reboot system now," and, "power off device." You can toggle through each choice using the volume up and down buttons, and once you highlight the one you want, hit the power button to select it. You can go to "power off device" in recovery mode and turn your phone off for now if you don't want to have to worry about it. If your phone is in download mode, it'll either be at the warning screen where you can hit volume up to continue, or volume down to cancel and restart the phone. If it is all the way in download mode, it'll say "downloading... do not turn off target !!" If it is on the warning screen, just continue into into download mode. If it is in download mode already, or you just continued into download mode, and you want to turn the phone off, press and hold volume up, volume down, power, and home button and hold them all down at the same time until the phone shuts off. Immediately after, let go of all the buttons, and then press and hold the volume up, home, and power buttons until the phone comes back on, and in the top left corner, in blue, it'll say "Recovery booting." It is then that you let go of all the buttons. You will enter recovery there and be able to power the device off.
Anyway, I hope you already got it fixed, and if not, I hope this information helped. I'm not trying to be mean, but you really need to search through all of the forums, read everything, read people's comments for information on how to do these sort of things properly, and how to fix the problems. Rooting, installing custom roms and xposed is a little different on newer devices now. Mistakes can be much more costly now than they used to be, so unless you've read thoroughly on such processes, and/or have found a youtube video that helps and you're feeling confident about it, you might want to reconsider attempting to apply these kinds of changes to your phone. If you have any friends that are good at this stuff, maybe that would be another way as well. Anyway, best of luck to you.
Click to expand...
Click to collapse
I did all of this, except for the check md5thing, will try this today.
Yeah so im pretty sure my phone is done for good, I have literally tried to flash every stock firmware, blah blah there is. ik to put Bl with bl ap with ap etc. lol it used to be so easy...
brandonjames1212 said:
Yeah so im pretty sure my phone is done for good, I have literally tried to flash every stock firmware, blah blah there is. ik to put Bl with bl ap with ap etc. lol it used to be so easy...
Click to expand...
Click to collapse
What are you flashing FROM? From what you listed in the OP, you are trying to flash to APG1? What the device is on now could be on a newer firmware
kangi26 said:
What are you flashing FROM? From what you listed in the OP, you are trying to flash to APG1? What the device is on now could be on a newer firmware
Click to expand...
Click to collapse
I honestly dnt knnow what the phone originally was, I forgot, but i have tried pg1 Pf2 pb4.. atleast those are some of the files i have tried.. cant find any others.. currently about to try ph1
Ph1 failed too.
idk if this helps anything, but Here is exactly what it says on my download mode
"ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-G935A
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
FAP LOCK: ON
WARRANTY VOID: 0x0
QUALCOM SECUREBOOT: ENABLE
AP SWREV: B4(2,1,1,1,1) K1 S3
SECURE DOWNLOAD: ENABLE
brandonjames1212 said:
I honestly dnt knnow what the phone originally was, I forgot, but i have tried pg1 Pf2 pb4.. atleast those are some of the files i have tried.. cant find any others.. currently about to try ph1
Ph1 failed too.
idk if this helps anything, but Here is exactly what it says on my download mode
"ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-G935A
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
FAP LOCK: ON
WARRANTY VOID: 0x0
QUALCOM SECUREBOOT: ENABLE
AP SWREV: B4(2,1,1,1,1) K1 S3
SECURE DOWNLOAD: ENABLE
Click to expand...
Click to collapse
If you are trying to flash the stock ROM and you are on different bootloaders you are going to run into issues. I THINK (and could be wrong), you may be on version 4 (based off of the "AP SWREV: B4(2,1,1,1,1) K1 S3") again, I'm not positive on my assumption here, but, if that's the case you need to flash a stock ROM that is on version 4 of the bootloaders, something like G935AUCS4API2 (BL4)
kangi26 said:
If you are trying to flash the stock ROM and you are on different bootloaders you are going to run into issues. I THINK (and could be wrong), you may be on version 4 (based off of the "AP SWREV: B4(2,1,1,1,1) K1 S3") again, I'm not positive on my assumption here, but, if that's the case you need to flash a stock ROM that is on version 4 of the bootloaders, something like G935AUCS4API2 (BL4)
Click to expand...
Click to collapse
Thank you for responding, but I did download that one yesterday and tried that one too.. got the same error sadly ;/
brandonjames1212 said:
Thank you for responding, but I did download that one yesterday and tried that one too.. got the same error sadly ;/
Click to expand...
Click to collapse
If you go into Recovery Mode, you should be able to see what ROM you are on. From there, I'd do a system wipe like xjimmy suggested, power off, boot to Download mode, and try to flash the ROM that has matching bootloader
kangi26 said:
If you go into Recovery Mode, you should be able to see what ROM you are on. From there, I'd do a system wipe like xjimmy suggested, power off, boot to Download mode, and try to flash the ROM that has matching bootloader
Click to expand...
Click to collapse
Android recovery
MMB29M.G935AUCS4API2
samsung/hero2qlteuc/hero2qlteatt
6.0.1/MMB29M/G935AUCS4API2
I factory reset, But can you refer me to what i should download for the above.. tired of downloading wrong file and all.. lol have downloaded over 13gb worth of files.. dnt wanna fail again
Lol i see pi2... ive already done that one tho, but as he said before, i reset this time and gonna try again.. already have files for that one.. so about to try
brandonjames1212 said:
Android recovery
MMB29M.G935AUCS4API2
samsung/hero2qlteuc/hero2qlteatt
6.0.1/MMB29M/G935AUCS4API2
I factory reset, But can you refer me to what i should download for the above.. tired of downloading wrong file and all.. lol have downloaded over 13gb worth of files.. dnt wanna fail again
Click to expand...
Click to collapse
So you are on V4 Bootloaders, and API2, which is the current stock release.
I would
Download the stock API2 ROM from HERE and put them all on your desktop
Open Odin
In Recovery mode, wipe the device
Restart the phone in Download Mode then plug the phone into the PC
Put the downloaded files to their slots in Odin, and hit start
kangi26 said:
So you are on V4 Bootloaders, and API2, which is the current stock release.
I would
Download the stock API2 ROM from HERE and put them all on your desktop
Open Odin
In Recovery mode, wipe the device
Restart the phone in Download Mode then plug the phone into the PC
Put the downloaded files to their slots in Odin, and hit start
Click to expand...
Click to collapse
That is the exactly files i have currently trying again now that i reset phone.
OMG thank you guys so much, after a thousand tries.. it ended up being the files you linked (Which were the original files i used the very first time) I just never did the factory reset!!! after doing the reset and trying again!! its currently started actually through the process, instead of saying model mismatch ! hopefully it does the entire thing with no errrors!! THANK YOU GUYS SO MUCH...
brandonjames1212 said:
OMG thank you guys so much, after a thousand tries.. it ended up being the files you linked (Which were the original files i used the very first time) I just never did the factory reset!!! after doing the reset and trying again!! its currently started actually through the process, instead of saying model mismatch ! hopefully it does the entire thing with no errrors!! THANK YOU GUYS SO MUCH...
Click to expand...
Click to collapse
Excellent!
kangi26 said:
If you are trying to flash the stock ROM and you are on different bootloaders you are going to run into issues. I THINK (and could be wrong), you may be on version 4 (based off of the "AP SWREV: B4(2,1,1,1,1) K1 S3") again, I'm not positive on my assumption here, but, if that's the case you need to flash a stock ROM that is on version 4 of the bootloaders, something like G935AUCS4API2 (BL4)
Click to expand...
Click to collapse
Yes I'm trying to flash the stock firmware but I flashed the rooted bootloader in Odin I think, lol so that may be why I'm having issues. Cause mine fails every single time for the att version and it's driving me nuts and I can't find any video tutorial on it at all, and smart switch won't work with the att one lol Dicks
kshansen7692 said:
Yes I'm trying to flash the stock firmware but I flashed the rooted bootloader in Odin I think, lol so that may be why I'm having issues. Cause mine fails every single time for the att version and it's driving me nuts and I can't find any video tutorial on it at all, and smart switch won't work with the att one lol Dicks
Click to expand...
Click to collapse
Did you do a Factory Reset in Recovery first?
kangi26 said:
Did you do a Factory Reset in Recovery first?
Click to expand...
Click to collapse
No I haven't I'm about to and I'll let you know what happens
kangi26 said:
Did you do a Factory Reset in Recovery first?
Click to expand...
Click to collapse
OK did a reset wiped her out set it up and wallllllaaaa it's fixed golden!! You sir helped a bunch thanks again this thread saved my nuggets
kshansen7692 said:
OK did a reset wiped her out set it up and wallllllaaaa it's fixed golden!! You sir helped a bunch thanks again this thread saved my nuggets
Click to expand...
Click to collapse
Sorry to come back to the party so late. Things have been hectic here. I'm glad these guys were able to get you all fixed up.
I got a bricked Samsung Galaxy Note 4 (910F) vodafone branded.
it's totally broken I can't start it, can't go into recovery (the hardware buttons are OK).
I can only go into download mode.
tried flashing everything with odin back to stock. followed many different instructions and now I'm lost.
can someone tell me what exact files I need?
I think I have the right firmware downloaded BUT what about the bootloader? on sammobile under germany-vodafone there are so many different versions which one shall I choose?
AND: Do I need CSC? if so which one and where to find? Couldn't find it on sammobile.
And am I right with putting the bootloader under BL, the firmware under AP, the CP (whatever this is) under CP, the csc under csc?
repartition unchecked as I read somewhere.
I still don't understand what this "pit" file is for and I'm not sure if I have the right one.. never had a phone with sooo many different firmware files..
I'm used to flash via fastboot "recovery.img, boot.img, system.img" odin is a new thing for me
HELP PLEASEEE :'(
the reactivation lock is on.
nekrosmsk said:
I got a bricked Samsung Galaxy Note 4 (910F) vodafone branded.
it's totally broken I can't start it, can't go into recovery (the hardware buttons are OK).
I can only go into download mode.
tried flashing everything with odin back to stock. followed many different instructions and now I'm lost.
can someone tell me what exact files I need?
I think I have the right firmware downloaded BUT what about the bootloader? on sammobile under germany-vodafone there are so many different versions which one shall I choose?
AND: Do I need CSC? if so which one and where to find? Couldn't find it on sammobile.
And am I right with putting the bootloader under BL, the firmware under AP, the CP (whatever this is) under CP, the csc under csc?
repartition unchecked as I read somewhere.
I still don't understand what this "pit" file is for and I'm not sure if I have the right one.. never had a phone with sooo many different firmware files..
I'm used to flash via fastboot "recovery.img, boot.img, system.img" odin is a new thing for me
HELP PLEASEEE :'(
the reactivation lock is on.
Click to expand...
Click to collapse
The note 4 firmware is usually only 1 file that contains all you need. It contains the bootloader and CSC that you pick during download. Just pick the CSC for your country.
This is unless you get a 4 file repair firmware, which contains separate bootloader, system, and CSC files.
The pit file is only needed to repartition your device.
But with all off that aside, you state that your activation lock is activated. These means the phone was password protected.
If you tell me your country, I can at least point you to the correct firmware. So at least you'll know you got the correct one.
But as far as the activation lock, I can't help with that. "Google"
Edit. I now see you mentioned Germany Voda.
So here's the most current firmware for your device.
https://fws03.updato.com/GALAXYNOTE4/SM-N910F/TCL/SM-N910F_1_20171228192640_l5rw6mqv67.zip
Download and unzip.
Then if it's just 1 file that's .md5 then you put it in AP slot.
If it's 4 files put them in appropriate slots.
aaron74 said:
The note 4 firmware is usually only 1 file that contains all you need. It contains the bootloader and CSC that you pick during download. Just pick the CSC for your country.
This is unless you get a 4 file repair firmware, which contains separate bootloader, system, and CSC files.
The pit file is only needed to repartition your device.
But with all off that aside, you state that your activation lock is activated. These means the phone was password protected.
If you tell me your country, I can at least point you to the correct firmware. So at least you'll know you got the correct one.
But as far as the activation lock, I can't help with that. "Google"
Edit. I now see you mentioned Germany Voda.
So here's the most current firmware for your device.
https://fws03.updato.com/GALAXYNOTE4/SM-N910F/TCL/SM-N910F_1_20171228192640_l5rw6mqv67.zip
Download and unzip.
Then if it's just 1 file that's .md5 then you put it in AP slot.
If it's 4 files put them in appropriate slots.
Click to expand...
Click to collapse
This reactivation lock doesn't matter I found a solution how to bypass it when the phone is set up running android.
my question is, is it possible to flash firmware to the note4 at all with reactivation lock on? Or is that just an android thingy?
And yes please that would be nice if you show me the right firmware.
My model:
N910F GSMH
I believe it is vodafone branded because when it once worked it showed a vodafone logo while starting up.
my country is Germany.
I hope thats enough info :/
nekrosmsk said:
This reactivation lock doesn't matter I found a solution how to bypass it when the phone is set up running android.
my question is, is it possible to flash firmware to the note4 at all with reactivation lock on? Or is that just an android thingy?
And yes please that would be nice if you show me the right firmware.
My model:
N910F GSMH
I believe it is vodafone branded because when it once worked it showed a vodafone logo while starting up.
my country is Germany.
I hope thats enough info :/
Click to expand...
Click to collapse
I believe it should still flash with lock. If it isn't flashing something is wrong.
If you can't get Odin to flash that firmware try this and see what happens.
Download TWRP and flash it. Can you boot into recovery then? If so download a custom rom and flash it and see what happens.
TWRP: https://eu.dl.twrp.me/trlte/twrp-3.2.1-0-trlte.img.tar
Do you have Samsung drivers installed on PC? http://developer.samsung.com/common/download/check.do?actId=698
Do you have a good Odin? https://dl.sammobile.com/Odin3-v3.13.1.zip
aaron74 said:
I believe it should still flash with lock. If it isn't flashing something is wrong.
If you can't get Odin to flash that firmware try this and see what happens.
Download TWRP and flash it. Can you boot into recovery then? If so download a custom rom and flash it and see what happens.
TWRP: https://eu.dl.twrp.me/trlte/twrp-3.2.1-0-trlte.img.tar
Do you have Samsung drivers installed on PC? http://developer.samsung.com/common/download/check.do?actId=698
Do you have a good Odin? https://dl.sammobile.com/Odin3-v3.13.1.zip
Click to expand...
Click to collapse
I have the right latest samsung drivers installed yes.
I have the Odin version you just sent a link of. ( I also tried different older versions but no success).
I can't boot into recovery doesn't work. the hardware buttons are 100% working as I have to press vol+ to confirm to go into download mode.
I tried flashing TWRP and CWM both didn't work "custom recovery blocked by A/L error".
I can successfully flash firmware with Odin. It says "PASS" and then the phone reboots and is stuck on Samsung Logo. and sometimes it just shows blue text "recovery booting" but is stuck. nothing happens.
nekrosmsk said:
This reactivation lock doesn't matter I found a solution how to bypass it when the phone is set up running android.
my question is, is it possible to flash firmware to the note4 at all with reactivation lock on? Or is that just an android thingy?
And yes please that would be nice if you show me the right firmware.
My model:
N910F GSMH
I believe it is vodafone branded because when it once worked it showed a vodafone logo while starting up.
my country is Germany.
I hope thats enough info :/
Click to expand...
Click to collapse
Hey sorry the link you've sent doesn't work :/
aaron74 said:
The note 4 firmware is usually only 1 file that contains all you need. It contains the bootloader and CSC that you pick during download. Just pick the CSC for your country.
This is unless you get a 4 file repair firmware, which contains separate bootloader, system, and CSC files.
The pit file is only needed to repartition your device.
But with all off that aside, you state that your activation lock is activated. These means the phone was password protected.
If you tell me your country, I can at least point you to the correct firmware. So at least you'll know you got the correct one.
But as far as the activation lock, I can't help with that. "Google"
Edit. I now see you mentioned Germany Voda.
So here's the most current firmware for your device.
https://fws03.updato.com/GALAXYNOTE4/SM-N910F/TCL/SM-N910F_1_20171228192640_l5rw6mqv67.zip
Download and unzip.
Then if it's just 1 file that's .md5 then you put it in AP slot.
If it's 4 files put them in appropriate slots.
Click to expand...
Click to collapse
hey thanks in advance, but this link doesnt work it says "hotlinking is not cool". anyways I searched the firmware for my model number on this site and applied the "germany vodafone" filter. but there are still soo many different entries which one shall I choose? The latest date?
nekrosmsk said:
hey thanks in advance, but this link doesnt work it says "hotlinking is not cool". anyways I searched the firmware for my model number on this site and applied the "germany vodafone" filter. but there are still soo many different entries which one shall I choose? The latest date?
Click to expand...
Click to collapse
Here's webpage
https://updato.com/firmware-archive-select-model?record=58770125168D11E89F15FA163EE8F90B
After you flash, how long are you waiting for it to boot?
Sometimes it takes awhile.
aaron74 said:
Here's webpage
https://updato.com/firmware-archive-select-model?record=58770125168D11E89F15FA163EE8F90B
After you flash, how long are you waiting for it to boot?
Sometimes it takes awhile.
Click to expand...
Click to collapse
Thanks for the link I'm downloading.
After flashing odin says PASS and my note 4 reboots. then there are 2 cases which in my view appear randomly. Either it shows the samsung logo and is stuck.
OR it shows the samsung logo and a blue little text in the upper left corner saying "recovery booting" and is stuck. I waited like 5 minutes. shall I wait longer? :/ hm..I'll try
OH and sometimes the screen just goes black idk if it really turns off after getting stuck on samsung logo.
Pull the battery, leave it out for 10+ minutes
Put battery back in
Boot to download mode (Power + Vol Down + Home)
Then try (re)flashing stock ROM via odin, i would try the earliest you can find to have the best chance, you can always flash a later one if you get it running
Better range of ROMS from sammobile, i never use updato for that reason: https://www.sammobile.com/firmwares/galaxy-note4/SM-N910F/VD2/
If none of that works, then its likely you have a hardware fault ...emmc or other
stylemessiah said:
Pull the battery, leave it out for 10+ minutes
Put battery back in
Boot to download mode (Power + Vol Down + Home)
Then try (re)flashing stock ROM via odin, i would try the earliest you can find to have the best chance, you can always flash a later one if you get it running
Better range of ROMS from sammobile, i never use updato for that reason: https://www.sammobile.com/firmwares/galaxy-note4/SM-N910F/VD2/
If none of that works, then its likely you have a hardware fault ...emmc or other
Click to expand...
Click to collapse
So I tried flashing. after flashing OH WONDER it said recovery booting and then it showed this green android logo thing with a rotating icon in it "you know what I mean" but then it stopped and just turned off.. I could freak out really.. I tried flashing again. same issue. I could then press the recovery mode key combo to get into this rotating android logo screen but everytime it just freezes and turns off. yes the battery is fully charged before I started flashing this firmware now. I flashed the one u said the earliest. So Now I tried the one the other guy here showed me. didn't work either. it just gets stuck at samsung logo. I found a repair firmware for my model containing (pit, bl, ap, cp, csc and odin) I flashed all but odin fails "write error". I then tried odin v3.0.7 but then it got stuck while flashing the system image. I waited like 1 hour. nothing. tried it again. nothing it freezes on the same position. I then tried the same on the latest versions of odin v3.12.3, 3.12.7 and on 3.13.1 but it also freezes on system.img.ext4 image flashing..
nekrosmsk said:
So I tried flashing. after flashing OH WONDER it said recovery booting and then it showed this green android logo thing with a rotating icon in it "you know what I mean" but then it stopped and just turned off.. I could freak out really.. I tried flashing again. same issue. I could then press the recovery mode key combo to get into this rotating android logo screen but everytime it just freezes and turns off. yes the battery is fully charged before I started flashing this firmware now. I flashed the one u said the earliest. So Now I tried the one the other guy here showed me. didn't work either. it just gets stuck at samsung logo. I found a repair firmware for my model containing (pit, bl, ap, cp, csc and odin) I flashed all but odin fails "write error". I then tried odin v3.0.7 but then it got stuck while flashing the system image. I waited like 1 hour. nothing. tried it again. nothing it freezes on the same position. I then tried the same on the latest versions of odin v3.12.3, 3.12.7 and on 3.13.1 but it also freezes on system.img.ext4 image flashing..
Click to expand...
Click to collapse
Try the Samsung Smart Switch for PC - like this : https://www.youtube.com/watch?v=9QhJngOuLQ4&t=337s
Good luck, maybe it will work - for me it did work for the 910C.
w41ru5 said:
Try the Samsung Smart Switch for PC - like this : https://www.youtube.com/watch?v=9QhJngOuLQ4&t=337s
Good luck, maybe it will work - for me it did work for the 910C.
Click to expand...
Click to collapse
doesnt work. I tried several versions of smartswitch AND samsung kies. nothing works it always says my model is not supported. I reinstalled drivers. tried on another pc. tried another usb port. yes I'm using the original stock usb cable. model not supported. But I've also read that in other threads that the 910F model seems to be unknown by kies or smartswitch. I'm rly starting to hate samsung now. I have never ever had so many problems with flashing and so on.
nekrosmsk said:
So I tried flashing. after flashing OH WONDER it said recovery booting and then it showed this green android logo thing with a rotating icon in it "you know what I mean" but then it stopped and just turned off.. I could freak out really.. I tried flashing again. same issue. I could then press the recovery mode key combo to get into this rotating android logo screen but everytime it just freezes and turns off. yes the battery is fully charged before I started flashing this firmware now. I flashed the one u said the earliest. So Now I tried the one the other guy here showed me. didn't work either. it just gets stuck at samsung logo. I found a repair firmware for my model containing (pit, bl, ap, cp, csc and odin) I flashed all but odin fails "write error". I then tried odin v3.0.7 but then it got stuck while flashing the system image. I waited like 1 hour. nothing. tried it again. nothing it freezes on the same position. I then tried the same on the latest versions of odin v3.12.3, 3.12.7 and on 3.13.1 but it also freezes on system.img.ext4 image flashing..
Click to expand...
Click to collapse
afaik the "repair" fimeware is no better than flashing a stock ROM in one file...
its startng to sound like a hardware error, if it cant even write to the dvice theres really not many (probably any) options left.
ive purposely bricked a phone and recovered it (not recommended of course), ive never had or never saw as much effort youve put in to try and recover a phone...
stylemessiah said:
afaik the "repair" fimeware is no better than flashing a stock ROM in one file...
its startng to sound like a hardware error, if it cant even write to the dvice theres really not many (probably any) options left.
ive purposely bricked a phone and recovered it (not recommended of course), ive never had or never saw as much effort youve put in to try and recover a phone...
Click to expand...
Click to collapse
me neither.. can't believe this.. how can a phone be physically damaged by flashing? paid 70 bugs for a note 4 with a software issue.. as I often do. recovered dead phones from sony, xiaomi, wiko, asus, lg, huawei etc... adb, fastboot and u good to go. odin is killin me.. gonna sell it as bricked.
Cleared caches?
R0B3RTF1SH3R said:
Cleared caches?
Click to expand...
Click to collapse
HOW? If I can't boot into recovery mode?
Hello there,
I recently tried to get Android 10 onto my old phone. But i already got stuck on trying to root it. First I could not install new firmware because of FAP lock.
Then when I tried to get around the lock, I tried to root the phone with this tutorial. But Odin failed at hidden.img. Several times. And now I am stuck with "Firmware upgrade encountered an issue Select recovery mode in Kies".
I tried flashing with deleted hidden.img - it does not work. When I add an .md5 extension, Odin says binary invalid. When I remove the ".md5", Odin just crashes.
Any ideas?
If it is somehow important: I once rooted this device, but for some update or app, idk, i went back to normal, I dont really remember. I use Windows 10.
Thanks
tHr4sh3R said:
Hello there,
I recently tried to get Android 10 onto my old phone. But i already got stuck on trying to root it. First I could not install new firmware because of FAP lock.
Then when I tried to get around the lock, I tried to root the phone with this tutorial. But Odin failed at hidden.img. Several times. And now I am stuck with "Firmware upgrade encountered an issue Select recovery mode in Kies".
I tried flashing with deleted hidden.img - it does not work. When I add an .md5 extension, Odin says binary invalid. When I remove the ".md5", Odin just crashes.
Any ideas?
If it is somehow important: I once rooted this device, but for some update or app, idk, i went back to normal, I dont really remember. I use Windows 10.
Thanks
Click to expand...
Click to collapse
there is no Android 10 available for this phone
2gg1 said:
there is no Android 10 available for this phone
Click to expand...
Click to collapse
Well thank you, but that not helping with the issue that i cannot flash my phone with stock rom via odin.
tHr4sh3R said:
Well thank you, but that not helping with the issue that i cannot flash my phone with stock rom via odin.
Click to expand...
Click to collapse
So you have download the samsung drivers? Unzipped the file with result of a .md5 file? connected your phone to the pc with download mode? And then putted the file on the AP section? And clicked start?
Everything i just mentioned (except the .md5) can you find on HighOnAndroid website. Try to get the odin from there.
Please reply if it worked
2gg1 said:
So you have download the samsung drivers? Unzipped the file with result of a .md5 file? connected your phone to the pc with download mode? And then putted the file on the AP section? And clicked start?
Everything i just mentioned (except the .md5) can you find on HighOnAndroid website. Try to get the odin from there.
Please reply if it worked
Click to expand...
Click to collapse
Well yes, I already did all you described, but did not get it from HighOnAndroid (I also tried, but the "samsung drivers" are Malware which is blocked by Windows, so...).
I know how to flash a phone. It just does not work because of some weird Error with the hidden.img. I also saw a ton of other people trying to flash their phone with this Error, but their solutions do not work. So I need someone with another solution.
tHr4sh3R said:
Well yes, I already did all you described, but did not get it from HighOnAndroid (I also tried, but the "samsung drivers" are Malware which is blocked by Windows, so...).
I know how to flash a phone. It just does not work because of some weird Error with the hidden.img. I also saw a ton of other people trying to flash their phone with this Error, but their solutions do not work. So I need someone with another solution.
Click to expand...
Click to collapse
Try get the samsung drivers from samsungs official website
I once again tried it with these drivers. No change.
I just want to tell you, that I am no idiot and I know how to flash a phone. It just is a very specific problem, that occurs a lot apparently: https://www.youtube.com/results?search_query=flash+galaxy+hidden.img+stuck
The problem is, that the solutions posted on Youtube and other places do. not. work. As I explained in my starting post.
Hi All,
I brick my SM-N9860, after playing with changing csc on TGY firmware I got to situation that my phone doesn't boot to system and I have FRP lock. Its stuck on download mode (attached pics).
Factory reset in recovery mode doesn't work and I cant flash new firmware with odin because of FRP lock.
Maybe some can help how can I resolve this issue?
I tried to flash combination file with pit file but I get error that there is a FRP lock. I wanted to try the option in recovery "Apply update with adb" but I cant find OTA file for SM-N9860.
From what I understood there is some boxes and dongles like Octoplus Pro Box that can reflash the phone and remove the FRP lock but maybe there is a solution easier than this that works with odin??
The problem is to make my phone to boot, than I could remove the FRP lock because my problem not the google credentials only that it not boot up after factory reset...
chetbiz said:
Hi All,
I brick my SM-N9860, after playing with changing csc on TGY firmware I got to situation that my phone doesn't boot to system and I have FRP lock. Its stuck on download mode (attached pics).
Factory reset in recovery mode doesn't work and I cant flash new firmware with odin because of FRP lock.
Maybe some can help how can I resolve this issue?
I tried to flash combination file with pit file but I get error that there is a FRP lock. I wanted to try the option in recovery "Apply update with adb" but I cant find OTA file for SM-N9860.
From what I understood there is some boxes and dongles like Octoplus Pro Box that can reflash the phone and remove the FRP lock but maybe there is a solution easier than this that works with odin??
The problem is to make my phone to boot, than I could remove the FRP lock because my problem not the google credentials only that it not boot up after factory reset...
Click to expand...
Click to collapse
Any one??
chetbiz said:
Any one??
Click to expand...
Click to collapse
Change the cable
Sent from my SM-F916B using Tapatalk
---------- Post added at 08:49 PM ---------- Previous post was at 08:47 PM ----------
I had the same problem
I change the cable and working on
Sent from my SM-F916B using Tapatalk
adeltamimy6 said:
Change the cable
Sent from my SM-F916B using Tapatalk
---------- Post added at 08:49 PM ---------- Previous post was at 08:47 PM ----------
I had the same problem
I change the cable and working on
Click to expand...
Click to collapse
Thanks) I wish it was just a cable..)
Try to look in maybe s20 ultra or s20 forum, they was released earlier and perhaps someone has already had this problem and solved it.
chetbiz said:
Any one??
Click to expand...
Click to collapse
Why don't you just put your Samsung account and password in? Because that's what you need to do in order to turn off the frp.. If you're going to tell us you don't know the Samsung user account and password that's only going to make us think the phone is stolen because that's basically what frp is meant to do block people from using it or doing updates or factory resetting it to try to remove the frp.. All you need is your Samsung account and password..
MrMike2182 said:
Why don't you just put your Samsung account and password in? Because that's what you need to do in order to turn off the frp.. If you're going to tell us you don't know the Samsung user account and password that's only going to make us think the phone is stolen because that's basically what frp is meant to do block people from using it or doing updates or factory resetting it to try to remove the frp.. All you need is your Samsung account and password..
Click to expand...
Click to collapse
Man are you serious?! I told you the problem not that I cant put my google or samsung credentials.. THE PHONE doesn't boot to the system at all can you understand this?! You can find me in another tread where I tried for cople weeks with guys from this forum to make our phone to work with native call record and reflash it many times with difrent firmware( CHC, TGY) and only one time I forgot to delete my google and samsung account before reflashing. So please dont tell me what you think, if you cant contribute to resolving and helping dont comment like you know something about me.
chetbiz said:
Man are you serious?! I told you the problem not that I cant put my google or samsung credentials.. THE PHONE doesn't boot to the system at all can you understand this?! You can find me in another tread where I tried for cople weeks with guys from this forum to make our phone to work with native call record and reflash it many times with difrent firmware( CHC, TGY) and only one time I forgot to delete my google and samsung account before reflashing. So please dont tell me what you think, if you cant contribute to resolving and helping dont comment like you know something about me.
Click to expand...
Click to collapse
Can you do me a favor with a patched version of Odin or just try multiple different Odin versions and flash only the CSC, AP and BL. and yes this is going to factory reset it probably but at least you might have the phone back.. Is this an unlocked bootloader phone btw? Edit: Make sure you're flashing the correct BL AP and CSC that the phone originally came with. Edit: Can you tell me what the last firmware was that you had on it?
MrMike2182 said:
Can you do me a favor with a patched version of Odin or just try multiple different Odin versions and flash only the CSC, AP and BL. and yes this is going to factory reset it probably but at least you might have the phone back.. Is this an unlocked bootloader phone btw? Edit: Make sure you're flashing the correct BL AP and CSC that the phone originally came with. Edit: Can you tell me what the last firmware was that you had on it?
Click to expand...
Click to collapse
I will try it, the phone is unrooted and with locked bootloader like it came from factory with no knox tripped. The last firmware that I was is "SM-N9860_20201112_TGY_N9860ZSU1BTJ9-N9860OZS1BTJ9-N9860ZCU1BT"
but the modification that I made was with SamKEY changed the CSC to CHC and after that flashed CHC csc file with odin, so in settings I had region CHC,CHC/CHC,TGY
Thanks for help
chetbiz said:
I will try it, the phone is unrooted and with locked bootloader like it came from factory with no knox tripped. The last firmware that I was is "SM-N9860_20201112_TGY_N9860ZSU1BTJ9-N9860OZS1BTJ9-N9860ZCU1BT"
but the modification that I made was with SamKEY changed the CSC to CHC and after that flashed CHC csc file with odin, so in settings I had region CHC,CHC/CHC,TGY
Thanks for help
Click to expand...
Click to collapse
Flash just the CSC, AP and BL of the firmware version N9860ZSU1BTJ9 if that doesn't work then try flashing the CSC, AP and BL from the firmware version N9860ZSU1ATGM and see if that works..
chetbiz said:
I will try it, the phone is unrooted and with locked bootloader like it came from factory with no knox tripped. The last firmware that I was is "SM-N9860_20201112_TGY_N9860ZSU1BTJ9-N9860OZS1BTJ9-N9860ZCU1BT"
but the modification that I made was with SamKEY changed the CSC to CHC and after that flashed CHC csc file with odin, so in settings I had region CHC,CHC/CHC,TGY
Thanks for help
Click to expand...
Click to collapse
Hi Chetbiz,
On your original thread, I did mention a ”patched” version of ODIN, I thought you already tried it. I guess not...
So there is still chance [emoji848].
Sent from my SM-N9860 using Tapatalk
fjorger said:
Hi Chetbiz,
On your original thread, I did mention a ”patched” version of ODIN, I thought you already tried it. I guess not...
So there is still chance [emoji848].
Click to expand...
Click to collapse
Hi fjorger)
I tryed with patched odin yesterday, what I didn't try is to flash only 3 files, AP, BL, CSC.. so I'll try it tomorrow evening after I'll get my phone back from technician hopefully he we'll succeed but I'm doubt it...
Thanks)
Got my phone back from technician, they didn't success to reflash it, I tried to flash firmware with patched odin and only BL, AP, CSC same here, error cant download pit file because of frp lock...
chetbiz said:
Got my phone back from technician, they didn't success to reflash it, I tried to flash firmware with patched odin and only BL, AP, CSC same here, error cant download pit file because of frp lock...
Click to expand...
Click to collapse
From what I understand I need Binary 4 file to unlock frp lock, maybe some one knows something about this file and if we got one anywhere?
I have never heard about it before, sorry
You may have to bite the bullet and send back to Samsung and have them reset the phone to original factory condition. It may cost some money, but better that than not having a phone at all -- a lot less than buying a new note for sure.
If you can't get it to flash on your own, I think that is your only option.
One quick thought - have you tried to turn off the phone and then boot back into Download mode? if not, try holding power and volume down until screen turns off - and when it is still off -quickly plug the USB cord into your phone. This will (should) force download mode - if it works - click volume up and then use Odin to try to flash the last firmware file you have (try all four files)
I don't know if this will help or make a difference, but if you haven't already tried this - it may work for you.
Good luck....
Geekser said:
You may have to bite the bullet and send back to Samsung and have them reset the phone to original factory condition. It may cost some money, but better that than not having a phone at all -- a lot less than buying a new note for sure.
If you can't get it to flash on your own, I think that is your only option.
One quick thought - have you tried to turn off the phone and then boot back into Download mode? if not, try holding power and volume down until screen turns off - and when it is still off -quickly plug the USB cord into your phone. This will (should) force download mode - if it works - click volume up and then use Odin to try to flash the last firmware file you have (try all four files)
I don't know if this will help or make a difference, but if you haven't already tried this - it may work for you.
Good luck....
Click to expand...
Click to collapse
Yes I think too that sending back to seller is my only option, I'm trying to connect with him, I bought on ebay, the problem he's doesn't answering me.
About download mode of course I entered the download mode after he was turned off. Nothing works, the strange thing that its fails to flash the latest tgy firmware, there I dont have an error about pit file or frp lock but its still failes on AP file when trying to write super.img... So I don't know what the solution for that, maybe in next firmware version it
will succeed
chetbiz said:
Yes I think too that sending back to seller is my only option, I'm trying to connect with him, I bought on ebay, the problem he's doesn't answering me.
About download mode of course I entered the download mode after he was turned off. Nothing works, the strange thing that its fails to flash the latest tgy firmware, there I dont have an error about pit file or frp lock but its still failes on AP file when trying to write super.img... So I don't know what the solution for that, maybe in next firmware version it
will succeed
Click to expand...
Click to collapse
You probably already tried this - but just in case, go to this link and download the most recent PATCHED Odin -
Then get several different USB Cords - Samsung Original is usually the best - but get different cords just the same -
then try to flash all four files in that patched odin - if it fails, close odin - open it again and reload the files and try again using a different USB Cord.
I believe that if you keep trying, you will eventually get it to work...
By the way, If you can't get the Seller to do the right thing - contact SAMSUNG Support and arrange to send it back to them. They may charge you (Probably around $100 or so I think) but they can definately help you get it working again.
Hope that helps - Good Luck.
Tried to flash the latest firmware N9860ZSU1BTK3 but still stuck on writing super.img in odin
Don't know what to do
chetbiz said:
Tried to flash the latest firmware N9860ZSU1BTK3 but still stuck on writing super.img in odin
Don't know what to do
Click to expand...
Click to collapse
super.img is from AP. Try to flash the build that was working on your phone before the issue happened, but without the AP.