Database Users

Hermes Keyboard

Hi,
I am just checking on my new Softbank Hermes
Just noticed that the keys the farthest right of the keyboard are little bit deeper (or sunk) that the ones on the left...but they response perfectly.
Are your unit the same ?
Thanks

anyone ? I have 3 days for exchange ..

I have an HTC Tytn and my keyboard is not like that.

My T key has a big oval of paint scraped off of it, and the backlight shows through, seems the center of my keyboard had a hump in it.
If you can exchange it, I likely would.

sectorlord said:
Hi,
I am just checking on my new Softbank Hermes
Just noticed that the keys the farthest right of the keyboard are little bit deeper (or sunk) that the ones on the left...but they response perfectly.
Are your unit the same ?
Thanks
Click to expand...
Click to collapse
Internally the Hermes has on one side of the keyboard (can't remember if this is shown on the wiki pictures) a foam rubber block running from the qwerty row down to the spacebar row. At the opposite end this is absent as internal parts make up the gap. It does not surprise me that there is some uneven-ness in external appearance though this should be very minimal. If your keyboard works perfectly I'd hang onto it given numerous reported problems with unresponsiveness of keys.
My keyboard if anything is a fraction higher in central area but not so high it scrapes on screen assembly.
Mike

Hi Mike,
Thanks for the tip...
Browsing from the pics, youre right, the left side has this foam block and the other side has none. That's why the keyboard is high on the left side and slowly sinking going to the right...(around half of millimeter..)
My unit is working perfectly, and I dont want to change it if the unit would be the same.... it might be the design ,...

sectorlord said:
Hi Mike,
My unit is working perfectly, and I dont want to change it if the unit would be the same.... it might be the design ,...
Click to expand...
Click to collapse
Quite right would be a gamble. Was just about to guide you to pictures just as you replied saying you'd seen them!!
Mike

Dont know why you have a hump on the center part of your keyboard...your foam block might be in the center in your case ?
I also saw that the keyboard PCB is fixed by a clip on the right and a black thing on the left side...do you know what's this thing ?
so...there a way to "perfect it" by putting a slightly thinner foam on the right side to equalize the pressure...
Do you have a pic on how to do it ?

Screen Rotation

Hi All,
I have updated to the latest AKU3 ROMs and also a few months ago I replaced the housing...However, I've noticed that the screen does not automatically rotate when the screen is swivelled??
Now is this because I did something during re-assembly of the housing OR is there something in the ROM's that disables the hardware somehow??
Cheers
ODY

Unlikely to be the rom, since it's part of the system HTC provided.
If it's been disassembled it's more likely that.
V

vijay555 said:
Unlikely to be the rom, since it's part of the system HTC provided.
If it's been disassembled it's more likely that.
V
Click to expand...
Click to collapse
hey VJ, sorry to bother but do you know what jumper/cable/connector/switch to jump/disconnect/tape inside the Universal to keep it from switching?

I'm sure I saw someone mention that the screen rotation is done by a magnet and switch? It's possible that maybe a small magnet fell out during disassembly? But I have looked throught the Universal repair manual and I can't find any reference to such a magnet??

I'd be nice to know exactly where it is so one would be able to take it out, if it were easy. I don't know if I wanna disasemble mine yet...
EDIT found it!! If you use a very, very light metal chain, as I did, with a keyring @ end, you can hover it around the Universal and see the tension of the chain when it's near the magnet. the keyring sticks too!
it's on the lid, behind the video-call video camera. I'm going to check the lid part of the manual.

Well taking the screen section apart is easy! You don't have to disassemble the whole unit. Looks like my magnet fell out then! Trouble is I want to sell mine so I'll just have to declare the auto screen rotate doesn't work (I've made sure that there is the rotate screen icon on the task bar though!!)
Cheers
Ody

odyseus said:
Well taking the screen section apart is easy! You don't have to disassemble the whole unit. Looks like my magnet fell out then! Trouble is I want to sell mine so I'll just have to declare the auto screen rotate doesn't work (I've made sure that there is the rotate screen icon on the task bar though!!)
Cheers
Ody
Click to expand...
Click to collapse
it works!! I tested it with the very small and highly magnetic point in the bezel of my tablet PC (to hold the pen) and it did change orientation.
thing is that it seems to be stuck beside the sound-holes (when the unit is closed).
I wonder how could I disassemble the lid only? are none of those screws @ the bottom connected to the back part of the lid? if so, that would be awesome!

Hi, on the xda's ftp, you'll find the maintenance manual for Universal...may help you to disassemble yours

thanx for the link!
however, it seems rather risky to try to pry the bezel open while still on the unit. Anyways I'm doing it right know. I'll get back to you.

I did pry it out and took the magnet off... painless(*) procedure and flea-sized magnet! don't loose!
I took a couple of pictures detailing the magnet position and the lid disassembled while still on the unit.
if you want to do this procedure do not loose the tiny screws and...
(*) be careful with the outer speaker (the one that lets you hear a call while the screen is facing the keyboard when closed), it isn't hard wired, it's just two small and fine contacts that might get distorted when putting the lid cover back... I had to take mine out again to correct this problem.
also, be careful with the screw driver and digitizer, as you'll be working in very akward positions to avoid disassembling the whole unit, and take off the battery of course.

Thanks for the photos - looks like my magnet feel out so I bought some 1/8 inch square magnets from ebay. It took a couple to find the sweet spot where the screen rotated but at least it works fibe now!
Cheers
Ody

odyseus said:
Thanks for the photos - looks like my magnet feel out so I bought some 1/8 inch square magnets from ebay. It took a couple to find the sweet spot where the screen rotated but at least it works fibe now!
Cheers
Ody
Click to expand...
Click to collapse
no problem. I'm also going to put the magnet back, now the unit doesn't now when it's closed, and therefore the outer speaker does not work. the screen also does not turn off when closed, only when the system timer tells it too... oh well.

you can turn the screen off by pressing the power button briefly.
no ext speaker though! maybe there's a way in software to disable just the rotation; i think the guys trying to get linux comfortable on the universal have some experience with it, maybe they can help.

[Q] Touch screen and capacitive buttons not working!

Hi guys,
What could be the possible reasons for a touchscreen and the capacitive buttons to stop working?
I purchased my Huawei U8800 only very recently but it was purchased 2nd hand. The phone came pre-installed with a custom rom, which is this one here: http://forum.xda-developers.com/showthread.php?t=1481168
I've had very minimal use of it ever since I received it, due to the reason that I have exams as I'm an UNI student. Therefore, I haven't modified the phone in any way, i.e I have not overclocked it or flashed a different kernel or recovery etc. The only thing I've done is installed GO SMS PRO and used it for txting and calling, that's it.
At first, everything seems to work fine. But on my 2nd day of use, the touchscreen started acting weird, where the right hand side of the screen stops working for no reason, as well as the 2 capacitive buttons on the right half of the screen (HOME and SEARCH). Then after a while, the BACK capacitive button on the left half of the screen stopped working, and eventually all 4 capacitive buttons and the entire screen stopped working.
The phone still turns on, but the entire screen doesn't pick up any finger input and there isn't any haptic feedback or vibration from the capacitive buttons. When I boot into the recovery, this is also the same.
So I contacted the seller about this, and he advised me to flash the Cyanogenmod 7.2 rom to see if this fixes the problem. It didn't, the touchscreen still doesn't work.
I'm wondering if this is related to the digitizer, which is the part of the phone that sense your finger inputs? If not, what are the other parts of the phone that could relate to the capacitive buttons and touch screen?

Definately a digitizer problem. The capacitive buttons are part of the touch screen, the touch screen is extended over the bottom of the display.
You should buy a new one from eBay or similar. If you want to buy it with a frame (black part on the front), you will have to open your phone to see if the front speaker is big or small. There are two types of front speakers and they are not cross-compatible. If you just want to buy the digitizer, you will have to remove the old digitizer from it's frame and add some glue on the new one to make sure it won't stick out.
If you don't want to mess with your phone, I am sure there are paid services that will do it for you, since replacing the digitizer is fairly easy.

Blefish said:
Definately a digitizer problem. The capacitive buttons are part of the touch screen, the touch screen is extended over the bottom of the display.
You should buy a new one from eBay or similar. If you want to buy it with a frame (black part on the front), you will have to open your phone to see if the front speaker is big or small. There are two types of front speakers and they are not cross-compatible. If you just want to buy the digitizer, you will have to remove the old digitizer from it's frame and add some glue on the new one to make sure it won't stick out.
If you don't want to mess with your phone, I am sure there are paid services that will do it for you, since replacing the digitizer is fairly easy.
Click to expand...
Click to collapse
thanks for your reply mate!
Ok so I've found this one here:
http://www.ebay.com/itm/Original-To...Glass-For-Huawei-U8800-Ideos-X5-/170721993712
Since it says it's "original", I don't have to worry about the speaker problem right?

chaoscreater said:
thanks for your reply mate!
Ok so I've found this one here:
http://www.ebay.com/itm/Original-To...Glass-For-Huawei-U8800-Ideos-X5-/170721993712
Since it says it's "original", I don't have to worry about the speaker problem right?
Click to expand...
Click to collapse
They are selling the digitizer, so there will be no problems as it's only the digitizer glass and not the frame around it. The frame itself is holding the digitizer and the speaker so that's why there may be issues when buying the front cover.
If you need a disassembly tutorial, check my Mediafire (signature) -> Documents -> U8800 Basic Maintenance Manual. It's the official disassembly guide so you can be sure you are doing it right .

Blefish said:
They are selling the digitizer, so there will be no problems as it's only the digitizer glass and not the frame around it. The frame itself is holding the digitizer and the speaker so that's why there may be issues when buying the front cover.
If you need a disassembly tutorial, check my Mediafire (signature) -> Documents -> U8800 Basic Maintenance Manual. It's the official disassembly guide so you can be sure you are doing it right .
Click to expand...
Click to collapse
Wait, that doesn't have the frame around it? I thought the black part surrounding the glass is the frame? I'm confused.......
I just want something that looks exactly like shown in that Ebay listing photo, where it has that bit of the connector part that you push into the motherboard (or whatever it's called on the phone).

chaoscreater said:
Wait, that doesn't have the frame around it? I thought the black part surrounding the glass is the frame? I'm confused.......
I just want something that looks exactly like shown in that Ebay listing photo, where it has that bit of the connector part that you push into the motherboard (or whatever it's called on the phone).
Click to expand...
Click to collapse
On your listing, it does not have frame.
If it's without frame, it is simply the front glass with connector. If it is with the frame, it has the black curve too (and speaker with led).
See this:
Without frame.
With frame.
Hope it makes sense now

Blefish said:
On your listing, it does not have frame.
If it's without frame, it is simply the front glass with connector. If it is with the frame, it has the black curve too (and speaker with led).
See this:
Without frame.
With frame.
Hope it makes sense now
Click to expand...
Click to collapse
Ahh ic ic.....so would I need to use glue to stick the digitizer glass onto the frame?

chaoscreater said:
Ahh ic ic.....so would I need to use glue to stick the digitizer glass onto the frame?
Click to expand...
Click to collapse
Yeah, but not much. Maybe you don't need to add any glue at all, the old one might hold it too.

u8800-51 touch screen bottom not responding
Blefish said:
On your listing, it does not have frame.
If it's without frame, it is simply the front glass with connector. If it is with the frame, it has the black curve too (and speaker with led).
See this:
Without frame.
With frame.
Hope it makes sense now
Click to expand...
Click to collapse
hi blefish
just posted a similar question:
http://forum.xda-developers.com/showthread.php?p=39201328#post39201328
is it the same solution? (the 4 buttons at the bottom do not work as well as the lower half of screen)
my speaker is 15 mm by 5 mm long (i looked inside). is it big or small?
all the ebay posts do not mention a frame - i will be happy not to mess with the glue
thanks

huwaei G 510
Hi guys,
I did have the same problem with a Huawei G 510. Digitizer broken and replaced, but still not working.
I have no action on screen. It lits but i can't press any button. Either the 3 buttons are working.
Checked the plug, checked some voltage in the pins.
Any other ideas ?
Thanks in advance,
Miltos Matt

Nexus 7 lcd screen issue

I all i just start to chnage my lcd cracked on my nexus 7 2012, and i have a problem the black latch on the Zif connector CN1 on the LCD came out. The latch is not brake but it's difficult to reattach, it's very small and i don't know the right position.
I have a look on youtube and google but they are not precise view of this part.
If some one can send me a picture detailled picture of this connector it would be great.
Thanks for your help

bidontdi said:
I all i just start to chnage my lcd cracked on my nexus 7 2012, and i have a problem the black latch on the Zif connector CN1 on the LCD came out. The latch is not brake but it's difficult to reattach, it's very small and i don't know the right position.
I have a look on youtube and google but they are not precise view of this part.
If some one can send me a picture detailled picture of this connector it would be great.
Thanks for your help
Click to expand...
Click to collapse
i dont get which part are you talking about. would be nice if you post an image of that.

View attachment 2400374
Hi yes it's probably better with a picture, today i succeed by replacing the black latch on the zif connector.
I replace the ribbon on the connector, and i the ribbon seems fasten when i pull on it.
I reassemble all pieces of the nexus 7, but the screen is still black.
When i connect it to the Pc, i can see the nexus 7 but nothing on the screen totally black.
I try differents thing holding power and volume + etc...
And the nexus is alwways black, i heard some sound when i put my hand on the screen so the touchscreen works.
I probably need to change the LCD ribbon ? something to check compatibility of the LCD with the Nexus 7 or this the ribbon ?
Thanks for your help

ZIF
hello i am new here and i want to ask you can i replace digitalizer zifs on nexus 7 2012 wifi please help me

You are out of luck and should have been more careful. Those connectors cannot be repaired without some serious skills and tools that you don't have.
Buy a new motherboard and be more careful next time.

[Q] HTC HD2 Black screen after falling

My HTC HD2 with kitkat os falling from my hand and after that the screen shows nothing, my phone is alive and everything works like ringing vibrate alarm even touch screen and touch vibrate, but i see nothing and the display is dark.
whats my problem? can i fix it?
thanks for reply me

any body ????
muhama said:
My HTC HD2 with kitkat os falling from my hand and after that the screen shows nothing, my phone is alive and everything works like ringing vibrate alarm even touch screen and touch vibrate, but i see nothing and the display is dark.
whats my problem? can i fix it?
thanks for reply me
Click to expand...
Click to collapse
any body ????

probably need new screen assembly!
needs opening to check lcd connector to mainboard & if all connections good then new screen should be tried.
LCD & digitizer pre built assembly is only about $30 these days for decent ones but indeed not easy fit with some experience or good read up on procedure & good care when doing it.

Mister B said:
probably need new screen assembly!
needs opening to check lcd connector to mainboard & if all connections good then new screen should be tried.
LCD & digitizer pre built assembly is only about $30 these days for decent ones but indeed not easy fit with some experience or good read up on procedure & good care when doing it.
Click to expand...
Click to collapse
Thanks for reply me:good:
How can i open my phone? And where is connector located?
Do you have a link to view that?

Have a read of this thread for start
http://forum.xda-developers.com/showthread.php?t=1566179
Plenty more if do a search
Basically be very very careful, use plastic pry tool ONLY to remove back, start at top. 2 clips about 7mm in from top edges then once released work down right side, DO NOT stick any tools in near the volume key, if doing it right the back comes of very easy (2 pry tools are better as can keep one in top sstopping it clipping back in)
Once back off handle with care, rough handling breaks th spring contacts for antenna etc.
LCD from mainboad can be disconnected from mainboard without fully removing flex & is absolute best way do it.
I did write few posts on it so will try dig them up & link you.
If buy lcd/gigi assemble also buy a button board ribbon as they like only $3USD, with spare button ribbon you can easily plug new lcd/digi in & plug new button board ribbon into mainboard & hold a battery on it to do a test befoe sticking things together.
Also you likely damage ribbon if not careful so spare likely get used on rebuild.
Parts link is in HD2 Wiki
http://forum.xda-developers.com/wiki/HTC_HD2#Fixes.2C_Hints_.26_Tips