Database Users

How long does it take your Nexus to fully charge?

Just wondering, how long does it take you guys to fully charge (From anything below 20% to 100%) your nexus 7? Because I've seen a few posts about battery related problems, and personally I think mine chargers slower than it should.
Also, when I use a wire to extend the charger, it's as if it wont charge, for it to fully charge i'd have to leave it on for hours without use, Since they're aren't any plugs where I'd usually sit to use it, I need to move somewhere else cause the wire is quite small.
For example, I've had it on charge since 2PM today, when I plugged it in it was at 14% battery, now (4:20 PM) it's at 63%. This has been without use, just sitting there charging. Plugged in via the charger and wire that come with it, to an extension with 3 other plugs in it.

I received my N7 with about 40% charge and it seemed like it took a really long time on that first full charge. It has been better since. I have heard if you are not using the original cable for the N7, it will dramatically increase the time it takes to charge and it won't show the charging icon. The supplied cable is USB 3 and your other cables are most likely USB 2. You might want to buy a 6 foot or 2 meter USB 3 cable for convenience. Also, use the original 2 amp charger it came with.

Groid said:
I received my N7 with about 40% charge and it seemed like it took a really long time on that first full charge. It has been better since. I have heard if you are not using the original cable for the N7, it will dramatically increase the time it takes to charge and it won't show the charging icon. The supplied cable is USB 3 and your other cables are most likely USB 2. You might want to buy a 6 foot or 2 meter USB 3 cable for convenience. Also, use the original 2 amp charger it came with.
Click to expand...
Click to collapse
Well, that explains why the extender doesn't work, but I haven't been using that to charge it since I noticed it slowed it down allot. I've only been using the stuff it comes with ever since I noticed that. Still VERY slow though, it's only just reached 96% since starting charging it at 2am. so it's taken 5 hours to get from 14% to 96%, pretty sure this isn't right.

I've collected some data on N7 charging and cables issues here.
http://forum.xda-developers.com/showpost.php?p=29983624
My completely drained N7 (<1%) takes approximately 3 hours and 49 minutes to completely charge it (N7 powered off during charging).

janedoesmith said:
I've collected some data on N7 charging and cables issues here.
http://forum.xda-developers.com/showpost.php?p=29983624
My completely drained N7 (<1%) takes approximately 3 hours and 49 minutes to completely charge it (N7 powered off during charging).
Click to expand...
Click to collapse
Which charger do you use?
And good to know it isn't a problem with my nexus I suppose.

Dazzuh said:
Which charger do you use?
And good to know it isn't a problem with my nexus I suppose.
Click to expand...
Click to collapse
OEM charger and OEM cable.

Nexus 10 taking more than a day to charge!!

Like the title says, my dad just bought a Nexus 10 and when he was charging it from 20%, it's taken more than an hour to charge to 50%. With that logic, the battery is only charging 30% a day, which means it would take 3-4 days from 0%-100%, and that simply is unacceptable. Is it a defective unit? I know about the Pogo charger, but I'm sure he'd rather not spend $25 on it just to find out it doesn't work.
Any suggestions or ways to fix this?
Thanks.
edit: To make things even sound worse, it only charged 2% in 1 hour and 30 minutes.

|| Acer || said:
Like the title says, my dad just bought a Nexus 10 and when he was charging it from 20%, it's taken more than an hour to charge to 50%. With that logic, the battery is only charging 30% a day, which means it would take 3-4 days from 0%-100%, and that simply is unacceptable. Is it a defective unit? I know about the Pogo charger, but I'm sure he'd rather not spend $25 on it just to find out it doesn't work.
Any suggestions or ways to fix this?
Thanks.
edit: To make things even sound worse, it only charged 2% in 1 hour and 30 minutes.
Click to expand...
Click to collapse
All I know is that on mine takes about 9 hours to charge with the original charger. The first time I've charged it from 16% with my Galaxy SIII cable, and it took over 14 hours.

That does seem long. I have the pogo charger and it does charge faster.
Before you buy the pogo, are you using the chargers that came with the N10? When I charge my N10 from a laptop/PC, it does charge slowly. So make sure you're charging with the correct voltage/amps.
Good luck!

I'm having a similar issue since the OTA update to 4.4.2.
I'll try changing USB cables, but I'm not optimistic. I'm tempted to try a factory reset if a different cord doesn't work.
Sent from my Nexus 10 using Tapatalk

Do you use the tablet while charging?
Is NFC enabled?
What setting is the GPS on; device only?
Sent from my Nexus 10 using XDA Premium 4 mobile app

|| Acer || said:
Like the title says, my dad just bought a Nexus 10 and when he was charging it from 20%, it's taken more than an hour to charge to 50%.
Click to expand...
Click to collapse
With Wifi on, NFC off, Location set to device only, bluetooth off, screen off, using my Pogo cable I get about 22% charge per hour so from 0% to 85% is 4 hours. Whilst on Pogo if I turn brightness to full and sound full then charge is held roughly flat. I moved to Pogo from the supplied cable as when watching stuff even when connected it was discharging, so now I'm never really out of power unless I stay unplugged a long time (about 6 hours unplugged max on low brightness)

anthony2424 said:
Do you use the tablet while charging?
Is NFC enabled?
What setting is the GPS on; device only?
Sent from my Nexus 10 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
This situation happens when the tablet isn't even on, so certain settings being enabled are not the issue.
And for more info, he is using the charger that came with the tablet, so we've just decided that we'll just send it back and get a new one because the battery is obviously defective.

|| Acer || said:
This situation happens when the tablet isn't even on, so certain settings being enabled are not the issue.
And for more info, he is using the charger that came with the tablet, so we've just decided that we'll just send it back and get a new one because the battery is obviously defective.
Click to expand...
Click to collapse
Have you tried a different cable/charger? AN hour to charge from 20% to 50%? Sounds about right to me. I always switch mine off when charging, I can live without when it' off. :good:

yets said:
Have you tried a different cable/charger? AN hour to charge from 20% to 50%? Sounds about right to me. I always switch mine off when charging, I can live without when it' off. :good:
Click to expand...
Click to collapse
I think clearly a human error in the word chosen explains it.
Instead of "...was charging it from 20%, it's taken more than an hour to charge to 50%. With that logic, the battery is only charging 30% a day, which means it would take 3-4 days from 0%-100%, and that simply is unacceptable."
it would make more sense if written "....was charging it from 20%, it's taken more than a day to charge to 50%. With that logic, the battery is only charging 30% a day, which means it would take 3-4 days from 0%-100%, and that simply is unacceptable. "
.... then the later post of its a dud and its been replaced makes sense....

nigelhealy said:
I think clearly a human error in the word chosen explains it.
Instead of "...was charging it from 20%, it's taken more than an hour to charge to 50%. With that logic, the battery is only charging 30% a day, which means it would take 3-4 days from 0%-100%, and that simply is unacceptable."
it would make more sense if written "....was charging it from 20%, it's taken more than a day to charge to 50%. With that logic, the battery is only charging 30% a day, which means it would take 3-4 days from 0%-100%, and that simply is unacceptable. "
.... then the later post of its a dud and its been replaced makes sense....
Click to expand...
Click to collapse
Ahh, I see. Good call in getting it replaced. I hope you have a better experience.

here are a few points
1) the AC USB come with N10 charge up to 2A.
2) the mini USB limit to about 1A
3) if you use other mini charger, that 1A is even smaller.
4) N10 battery is HUGE comparing to all tablet out there. It will take a long time to charge
Solution: get the pogo charging cable that cost $25 (very expensive and can only use for charging), that will fully charge 2A to your tablet which should reduce the time to less than 4hrs given no other power hog apps running at the same time. It will charge slower if that power hog app running too. You can tell by how warm/hot your tablet gets when running such app.
btw, go look at the disassemble of the N10. That battle makeup most of the tablet. LOL

workerantDroid said:
here are a few points
1) the AC USB come with N10 charge up to 2A.
2) the mini USB limit to about 1A
3) if you use other mini charger, that 1A is even smaller.
4) N10 battery is HUGE comparing to all tablet out there. It will take a long time to charge
Solution: get the pogo charging cable that cost $25 (very expensive and can only use for charging), that will fully charge 2A to your tablet which should reduce the time to less than 4hrs given no other power hog apps running at the same time. It will charge slower if that power hog app running too. You can tell by how warm/hot your tablet gets when running such app.
btw, go look at the disassemble of the N10. That battle makeup most of the tablet. LOL
Click to expand...
Click to collapse
Agree, BUT once you get >85% the rate of charge intake drops. I can get to 85% in 3.9 hours using Pogo cable, but that last 85%-100% is slower. My battery meter sees one kink 85-90 another 90-95 and a slow crawl 95-100. As the battery is not taking up 2A >85%, all chargers, all cables, will largely take the same 85%-100% but the Pogo cable with 2A input will get you to 85% quicker.
I have moved to a dual 2.1A output PSU.

duplicate post.

HyperTension said:
duplicate post.
Click to expand...
Click to collapse
I know you revised the post but just looked at the link to the PSU you mentioned.
Note that $10 one is dual USB socket but only 2.4A total meaning if it is charging the N10 taking 2A it can only offer 0.4A to something else meaning that other thing can only be something like a phone. More importantly is the opposite if you connect a powerpack USB battery which takes say 1.5A or 2A then your Pogo cable cannot deliver its full capability.
The PSU I mentioned earlier is dual 2.1A both concurrently meaning it can charge the N10 and something else also power-hungry like charging a 2A input or 1.5A input USB battery.
There are PSUs out there which can do 4 lots of 2A concurrent, I didn't get one as they were getting chunky and personally prefer two PSUs, a 2x2A + 1A for total 5A which does my N10, my USB battery (2+2) and my phone (1) concurrently taking two power sockets.
Check the details of specifications of these devices, PSUs and batteries vary wildly.

[Q] Pogo Cable Issue

Hello there developers,not sure if I'm posting on the right place but I have a really big problem. My new Pogo Cable arrived and I was so excited to use it,but my happiness didn't lasted fort too long. The problem is that the Tablet while charging with the Pogo cable is either charging slow ,or neither at all. This issue is available for both Lollipop and Kit-Kat,have upgraded an then downgraded with the hope that the issue will be solved. The original Micro -Usb cable works good but with the Pogo Cable in the Battery Monitor Widget it appears "Discharging" and "AC Plugged",and the charging rate is booring slow. Had the idea to measure the Voltage and the current Flow with a multimeter and got the surprise that while the voltage is 5.12 V the amperage is 0.12 A ,while the original charger pumps up to 2 Amps. Could this be the issue? Is there some electrical switch that should open and release all those 2 Amps or is this Cable a Hoax or something that is not fully functional? Thanks in advance,hope that you guys will enlight me somehow!

I've no idea if this is related but be aware that having your pogo plug connected while also having anything connected to the microUSB will stop charging. The charging icon (lightning bolt) will still appear but that I'd a false indicator. This limitation is due to the Android kernel and is present in all versions of Android.
I exclusively use a pogo plug to charge my Nexus 10 and it has always worked on all versions of Android including 5.0.2 which I'm on today. For me pogo plug charging has always been about 25 percent faster then USB charging.
Sent from my Nexus 10 using XDA Premium HD app

My experience is exactly the same as 3DSammy reports.

well my warranty is expired so i Decided to "surgically" dissmantle my Nexus 10 in a heroic attempt to find the cause and I have made a breakthrough (or at least I tought so). I got another Pogo cable ,and this one was good,the voltage was exactly 5 Volts measured and the Amperage that I got was 2.21 Amps measured with a 6 Ohm fuse,all these values where from the original Samsung charger. All things good,but the Tablet is still not charging at all,the same Lightning animations and even after 3~4 hours still no charge at all,and this is Lame in my opinion. So after opening the tablet,I got the idea to short the 3 and 4 pogo pins together,and assumed that this will draw all the power that the battery needs to charge,the idea was working i got 20% more power draw than the usb cable BUT for only let's say Half of hour ,and then the same old story,battery was discharging but the lightning animation was on. This is not so good and my suppose is that the Power Management iC from the motherboard is some how not managing the Pogo charge at all :laugh: so my next idea is to wire the charging Pogo pins directly to the battery and hope for the best. Regards! :good:

moky900 said:
well my warranty is expired so i Decided to "surgically" dissmantle my Nexus 10 in a heroic attempt to find the cause and I have made a breakthrough (or at least I tought so). I got another Pogo cable ,and this one was good,the voltage was exactly 5 Volts measured and the Amperage that I got was 2.21 Amps measured with a 6 Ohm fuse,all these values where from the original Samsung charger. All things good,but the Tablet is still not charging at all,the same Lightning animations and even after 3~4 hours still no charge at all,and this is Lame in my opinion
Click to expand...
Click to collapse
I've got one of the original n10 from first day of issue. My battery is going to hell after being used and charged every day for the past couple years. It's been on/run everyday since Dec. 2012. I have always had a problem charging while using it. My display is always set at about 1/3 bright. When my battery drops to critical, I plug in the pogo and usually put it in sleep mode to charge. It will quick charge that way.
If I still need to use it at critical battery level, plugged into the pogo plug, it maintains power and possibly gives it a very slow increase in charge. Almost none noticeable, but will maintain power level (unless tons of graphic, camera or movies along with full bright screen).
I've just taken it for granted that this is how it works. Pogo plug will maintain battery while using and will switch to quick charge once put into sleep mode or powered off. It's always acted that way, so I have never known anything different.
Ed

metaled222 said:
I've got one of the original n10 from first day of issue. My battery is going to hell after being used and charged every day for the past couple years. It's been on/run everyday since Dec. 2012. I have always had a problem charging while using it. My display is always set at about 1/3 bright. When my battery drops to critical, I plug in the pogo and usually put it in sleep mode to charge. It will quick charge that way.
If I still need to use it at critical battery level, plugged into the pogo plug, it maintains power and possibly gives it a very slow increase in charge. Almost none noticeable, but will maintain power level (unless tons of graphic, camera or movies along with full bright screen).
I've just taken it for granted that this is how it works. Pogo plug will maintain battery while using and will switch to quick charge once put into sleep mode or powered off. It's always acted that way, so I have never known anything different.
Ed
Click to expand...
Click to collapse
Well I'm sure about what did you said,but in my opinion this is a marketing bulls$h*t. Why would I use that Pogo cable if it's role is to charge only on sleep mode and powered off?I ordered because I thought that like the instructions of the pogo says:" it will charge the battery even when you are using it for movies and browsing,being more handy ,because you have the micro USB port free." I play games ,I surf the web,so my tablet is hooked up to a USB hub so I have connected a mouse,a keyboard and a game controller,so my USB port is full,and I hoped the pogo will help. Charging only on sleep is equal to zero for me,I need live charging,in the same time as the tablet runs games and other stuff. In my opinion this "glitch" should have been told on the pogo site,so I could full understand this cable and it's role. Shame on Samsung,30$ .for nothing! Thanks for the help!

M3 charging time question

Hi guys. I got my own M3 device and have quite long time for charging from 1% to 100%. - 3 h 55 min (~3 h to 95% and 50 min from 95 to 100%). Are you have the same and this is a payment for a long battery life, or maybe it should be quicker? Tell me please about your experience.

You must have a problem with your charging plug, or maybe your using another charger that didn't come with your device. I only see slow charging time when I don't use the charging cable and plug that came with the device.

Hanger4life said:
You must have a problem with your charging plug, or maybe your using another charger that didn't come with your device. I only see slow charging time when I don't use the charging cable and plug that came with the device.
Click to expand...
Click to collapse
Usung everything brand new from the device box. So, such time is abnormal? Can anyone confirm?
UPD: But you gave me an idea. Connected it to XIAOMI's Quick Charge and time decreased to less than 3 hours.

25W charger

i heard the battery get totally broken after one year of using the original 25W charger , what is ur experiences ? does ur phone over heat too when charging does it get to 50-60 C degrees?

I've been charging mine with the turbo charger since day one, it's been fine. There is technology built in to monitor the battery temps and ramp down the charge speed as the battery gets full. I've had my phone for 16 months now.

Max temp I get is 42-44c
Sent from my XT1580 Hammer using Tapatalk

same here : 15 months with my MXF the 25w turbo2 charger.
Battery never go over 45° in charge, battery life still as good as the first day

In my car I have the Moto 25w charger. With navigation and other apps running the temperature rises to about 46 degrees. At this point the charge rate drops. Only if my telephone is at the cool air and out of its cover does the charging rate remain at the full turbo charge rate
Sent from my XT1580 Hammer using Tapatalk

Alimataei said:
i heard the battery get totally broken after one year of using the original 25W charger , what is ur experiences ? does ur phone over heat too when charging does it get to 50-60 C degrees?
Click to expand...
Click to collapse
Not so much that the battery fails. The connector (which is kind of crucial for QC 2.0/3.0) or the charge controller craps out. Battery's fine. Was fine when I did my swap out for charge failure. It's not the battery, which people incorrectly presume is the problem- the charge system is a feedback loop process running in the background while the OS is running. When you're dead, down, no charge in the battery, the device only draws USB 2.0 power levels, 500mA, until the OS can come up enough to manage the charging. Part of the reason they do this is because you're using a USB connection to charge with and unless you've got the 1.5 A USB charge slot or an AC charger with the ability to source up to 2.4 A of juice, trying to pull that much current will wipe your USB port on a PC/Laptop/etc OUT. This is just with traditional charging. Turbo/QuickCharge charging is about raising the voltages over the USB 2.0 lines on a cable to up to 12v as opposed to 5, to allow you to jam a bit more current through the lines and to the device, effectively doubling the power being fed to the charge system. Problem with that is that you REALLY need the OS up and running to manage that. It requires info from the Charge Controller chip that is handshook from the charger.
If your charge controller is damaged, or if the cable doesn't have clean data and power lines, it just simply WON'T WORK. It will just USB mode charge until you fix the "problem"- either of which requires Lenovo to re-work the board...if it's even possible to fix. USB charging takes forever with this class of device- because the battery is a huge tank of juice compared to the devices of old. So it "looks" like the battery got "broke".
Having said this, there's about 20-40% of the units out there, depending on the crowd you listen to, that have a defective charge controller system and the phone flat-out won't ever go into any mode other than USB.