FRP lock - Odin, Heimdall, Smart Switch & Kies all don't work... - Samsung Galaxy S5 Neo Questions & Answers

Hi all,
I installed LineageOS (15?) on my S5 Neo, which worked perfectly fine for a while - until one day it didn't boot anymore because of "Custom binary blocked by FRP lock"
I tried several things now, all don't seem to work:
* Smart Switch says it cannot do emergency recovery on this phone (I can look up the exact message)
* Kies says "SM-G903F doesn't support initializing". I read something about downgrading not possible.
* Odin says:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 3049 M
<ID:0/003> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 3049 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> cm.bin
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And the phone says: SW REV. CHECK FAIL. DEVICE: 2, BINARY: 1
heimdall flash recovery says:
Initialising connection...
Detecting device...
Claiming interface...
Setting up interface...
Initialising protocol...
Protocol initialisation successful.
Beginning session...
Some devices may take up to 2 minutes to respond.
Please be patient!
Session begun.
Downloading device's PIT file...
PIT file download successful.
Uploading RECOVERY
100%
RECOVERY upload successful
Ending session...
Rebooting device...
Releasing device interface...
but heimdall flash --SYSTEM system.img says:
Initialising protocol...
Protocol initialisation successful.
Beginning session...
Some devices may take up to 2 minutes to respond.
Please be patient!
Session begun.
Downloading device's PIT file...
PIT file download successful.
Uploading SYSTEM
1%
ERROR: Failed to receive file part response!
ERROR: Retrying...
ERROR: Expected file part index: 0 Received: 1
ERROR: SYSTEM upload failed!
Ending session...
I was able to get into stock recovery once, but it said something like "update from external storage disabled"
...so all my ways are dead. Anyone knows anything for getting me a step further?
(I rebooted my phone to Download mode many times BTW, because that seemed to be necessary sometimes)

Yay! I finally managed to use this 2016's hack from https://github.com/Benjamin-Dobell/Heimdall/issues/347 and it's running again

Related

GT-1905 Demo unit firmware

I have got a hold of a demo unit (gt-19505x) and wanted to flash it to a standard firmware. So i choosed
hxxp://sammobile.c0m/firmwares/1/?model=GT-I9505&pcode=VDS
When in odin i get this error message:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDE_I9505VDSAMD8_I9505XXUAMDE_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> modem.bin
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
So i wonder if anyone have any experience with flashing demo units. Is this error caused to wrongly chosen rom or a corrupt file? Or can't the demo phones be flashed?
Is there any demo unit room out there that i can try to flash with, because now the phone gets stuck at the splash screen when i try to boot it.
EDIT:
I managed to boot it, was stuck along time on the splash screen tho, the downside is that wi-fi is'nt working. But i can tether via bluetooth from my SII.
Under device status it says its custom so i guess i can "update" the firmware via "software update".
But when it checks for a new version it starts by "registering device..." then i get an error saying "Processing faile" even tho i'm logged in with my samsung account.
Is this because im not on wi-fi and it will only scan for updates if im on wi-fi?
any luck ?

Flashing original Samsung firmware failing on cache.img in Odin

I've tried flashing the original Samsung roms on both Windows 7 & 8.1, on Odin 3.07, 3.09, 3.10.7 all failed in the same manner.
Flashing fails as soon as the system tries to flash cache.img.
Code:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> cache.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone is the SM-N900 Exynos variant.
h3llb3nd4 said:
I've tried flashing the original Samsung roms on both Windows 7 & 8.1, on Odin 3.07, 3.09, 3.10.7 all failed in the same manner.
Flashing fails as soon as the system tries to flash cache.img.
Code:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> cache.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone is the SM-N900 Exynos variant.
Click to expand...
Click to collapse
Udpate your Samsung drivers or simply install Kies 3. Try again then.
Joku1981 said:
Udpate your Samsung drivers or simply install Kies 3. Try again then.
Click to expand...
Click to collapse
I did install both Kies and Kies3, also made sure they weren't running. No avail. :/
h3llb3nd4 said:
I did install both Kies and Kies3, also made sure they weren't running. No avail. :/
Click to expand...
Click to collapse
Maybe is for that. Uninstall both. Only install now Kies 3 and try flash the firmware again.
* Are you sure that is the correct firmware for your device?
Your cache partition is most likely corrupted, just use the correct pit file for your n900 whilst flashing the rom.
Sent from my SM-N9005
Right, the issue was that I didn't flash the correct Pit file. But that's for another time.
NEW ISSUE!
In trying to solve the bad flash, during one of the flashes I checked NAND erase all. Now I just got the phone and have no EFS backups. is there any chance of fixing this? I don't have custom recoveries. Or do I have to send it in to Samsung?
The device boots fine, but I seemed to have wiped the phone's IMEI and baseband. The device can't register sims.

[Critcal help] please i delete my Phone system and i can not flash official frimware

hi please help me
i have a big problem in my Note 4 Samsung SM-N910C
i was rooting my phone by twrp... after some time i wanna delete root so i enter mY twrp then suddenly
wipe all
1-cach
2- Dalvik cach
3- System
4- Data
5-Internal storgae
6-Micro Sdcard
so i delete the phone system so it is not work again stuck only on twrp and when i try to install N910CXXU1COH4_N910COXA1COH4_N910CXXU1COH4_HOME.zip from sdcard it failed
and when i tried to install from Odin 10 N910CXXU1COH4_N910COXA1COH4_N910CXXU1COH4_HOME.tar.MD5
give me failed
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
so please how to fix it
My phone stuck only on Samsung note 4
Not sure if this will solve the issue, but read what I put here: http://forum.xda-developers.com/note-4/help/soft-bricked-note-4-n910f-t3306402
Thought I bricked my n910f, and all is good now!
But i do not have any stock frimaware on my phone i already delete the system
webby93
my odin log data
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910CXXU1COH4_N910COXA1COH4_N910CXXU1COH4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I didn't either, I completely wiped it.
What i think happened with me is that odin did put the stock firmware on even when it said it failed after like 5 mins. Then the allsamsungrecovery fixed the rest to let it boot up.
The only issue could be that your odin doesn't seem to have got quite as far as mine did. Can you only enter download mode and that's it?
i can enter download mod
but when i select the frimeware stock
The odin data appear log failed
and on the phone appeared : “SW REV CHECK FAIL DEVICE 2 BINARY 1”.
I'm really sorry, I don't think I'll be able to help any further. My knowledge is just from problem solving the few cases I've had to solve my self. Hopefully someone else can help you here.
Just Flash Lollipop 5.1.1 via odin which have coj5 or upgrade bootloader
you can't downgrade from coj5 bootloader you flash coh4 rom therefore you get error
http://forum.xda-developers.com/note-4/development/rom-note-4-mod-t3244665
flash this rom through odin complete stock and debloted firmware
download from here
https://docs.google.com/uc?id=0B8-hfA9ycQNoazRkV2xjNThWNWc&export=download
Best Regards,

Need help solving an error!

This is quite a long story. So I decided to flash twrp on my s7 edge (exynos) and root it with magisk. everything was working fine until i decided to turn off the oem lock and then restart the phone. as soon as the phone booted up, it shows the error "custom binary blocked by frp lock" and then automatically shuts down. I searched up the issue online and it told me that i should reflash my stock firmware and so i did.
1st error:
odin fails in flashing stock.
i tried to unplug the wire and retry and i get stuck on the "setup connection" part.
2nd error:
since it got stuck on the setup connection part, i tried to unplug it to try and restart the process but it did me no good. now the device says "An error occurred while updating the device software. Use the Emergency restore function in smartswitch pc program"
3rd error:
so i tried to use the smartswitch program but it says that my device is not supported and so im stuck to the 2nd error.
Please help. I tried reflashing stock firmware using odin and it still wont work (odin keeps failing). now the device only shows the 2nd error mentioned above and wont shut down unless it runs out of battery.
for additional info, this is the log of my odin:
<ID:0/005> Added!!
<ID:0/005> Removed!!
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 3943 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
(i tried to click start again and then odin gets stuck here)
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 3943 M
<ID:0/005> SetupConnection..

Need debrick help: accidentally checked repartition in Odin on Core Prime (G360H/DS)

My G360H/DS is stuck in a boot loop. I get the boot splash
Stock Recovery and TWRP both show errors mounting /cache/System/data etc .... so I'm guessing I really killed the partition table. However, I can still get into Download Mode, so I'm really hoping there is a chance to save my phone!
after retry flashing now Odin fails at system.img .. please help me
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 873 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Categories

Resources