This thread relates to MCU: CSN2_xxxxx, CSN2_D_xxxxx and CSN2_8600_D_xxxxx for PX4, PX5 and PX6 platforms
This thread is a mirror of russian 4pda to cover more users/developers.
All units are made by Klyde, but are sold under different brands.
I've been looking for a simple way to donate me if this thread is useful for you, all the ways are collected in one post there
The thread requires a new mainteiner. Details are there.
Hardware specifications:
CPU: Octa-core PX5 1.5GHz Cortex A53 64 bits CPU
ROM: 16/32/64G
RAM: 2/4G
Resolution: 1024*600
Out Power: 4*45Watt
Operating System: Android 8/9
Radio Tuner/Audio Chip: NXP6686 / TDA7851
Built-In WiFi Module /Support External 3G Dongle
Features: Radio Tuner,Built-in GPS,MP3 Player,Bluetooth,Touch Screen,TV,Mirror link,Built-In Microphone,Support Steering Wheel Control,Support Can-Bus
Useful tips
Tag [Android 8] means that it applicable to Android 8 , the same for [Android 9]. If there is no tag, it suits both versions.
Factory Settings password: 126
If you type 888 while opening Factory Settings, the Logo changing menu appears instead of Factory Settings. Logo1 replaces "Navigation system" picture, Logo2 replaces "android" picture. Logo2 is animated.
Developers mode password is 237
Password 927 opens menu, that helps to adjust screen brightens by changing VCOM value. You can set it between 1 and 100. Be careful with that!
[Android 8] How to get root: Use a rooting app, alternative link
[Android 9] How to root
Warning! You should be careful with that as it can brick your device once you tried to update SuperSu. Do not update SuperSu binary or the SuperSU app!!! You will get bootloop if that is updated!!! Also you have to wait until the tool completes its job, otherwise you can get no sound. If you face the mentioned problems, just re-flash your device. BE CAREFUL!.
Starting from android 8 January firmware there is an option "OFF" for "Power off delay if ACC OFF". it allows to keep android in a sleep mode forever. Please note that it consumes around ~9-10mA in this mode. Powered off device uses 4.8mA only (twice less than sleeping mode).
How to get enter stock recovery: hold reset(power) button, wait until sensor buttons start blinking, release and immediately press the button again. See video
To adjust the back camera brightness, just tap the screen when the camera is active.
Set custom logo
Detailed device schema
Known issues/limitations and fix/workaround for that
Lost wheel key settings and radio stations in case full power loss (yellow wire). Make sure that yellow wire is not disconnected when the car is stopped/locked.
Sound level is 10 (12) after reboot/sleep if you was listening louder; if it was less than 10 (12) stays the same. 12 appeared in Dec 11th firmware, it was 10 before that. Not topical starting from Dec 27th firmware, now you can define default sound between 12 10 and 20 in Car Settings-->Personal Settings. 10-20 is in Jan 17th firmware .
buzz in speakers caused by 433MHz alarm system and USB stick remounting.
small buzz caused by WIFI, observed in complete silence only. Not an issue if there are no connected devices.
There are lots of cases when wheel keys does not work at all. The reason is in wiring. Please study the head unit manual + car wiring scheme and put the needed wire to the correct connection shoe.
if you have canbus adapter and wheel buttons duplicate actions (i.e you pressed next track, but 2-3 tracks were switched, the same for sound level), just flash Jan 17 or newer firmware. Also it is possible to change wiring, but the firmware is much easier.
if you have canbus adapter and track switching is reversed (incorrect), just go to Factory Settings --> canbus and set keys_previous_next to change.
Bluetooth ODBII and hands-free (calls) does not work simultaneously. At the same time ODBII and BT Music works well simultaneously. Hardware limitation, no idea for now if that can be solved.
Voice dialing, voice search do not work on some devices. Fixed in May 8th firmware.
1.PX5 Firmware.
You can combine different firmware and MCU (I.e. take the pumpkin MCU + April firmware or vice versa). MCU from Android 8 is compatible with Android 9. Mind DSP only while updating MCU.
The factory does not provide me with a changelog! Do not ask about it.
Android 10.
Mar 31st 2021 202103310921
Mar 23rd 2021 202103231402 with Erisin launcher
Jan 4th 2021 202101041604 + MCU CSN2_D_1152020_114303
Fake Android 10.
It is the same android 9 firmware, but with the changed launcher, radio and Bluetooth app.
July 6th 202007061156
Android 9.
The link for the most recent firmware and MCU: with DSP and without DSP. _D_ in the MCU version means that it is for units with DSP.
All available versions of MCU are on my Google drive.
Firmware history and links:
Sep 1st 2020 202009011014
June 1st 202006010933
Android 8.
The link for the most recent firmware and MCU: with DSP and without DSP. _D_ in the MCU version means that it is for units with DSP.
All available versions of MCU are on my Google drive.
Firmware history and links:
June 18th 201906180853 + MCU CSN2_06102019_114308
2. PX6 Firmware
Android 10.
Aug 27th 2021 202108271854
Mar 31st 2021 202103311813
Oct 27th 2020 202010270905
Android 9.
July 1st 202007011143
3. PX5 Android 9 for 1 DIN units with MCU CSN2_8600_D
The differences between this unit are on Russian 4pda
Firmware 201911301053 + MCU CSN2_8600_D_11202019_162651 is located on Google Drive
4. PX4 Firmware
Android 10.
Oct 23rd 2020 202010231137
The instruction how to upgrade is there
The list of purchased devices
KLYDE for Subaru Forester
OTOJETA for Nissan and 3 more for Sportage IV
KANOR 2pcs for Oulander and 2DIN 2Din and 2pcs for Mazda, and for cee'd
SKYSHADOW for hyundai i40, and for Prado, also 2Din with 32Gb and 64Gb
HaiSunny for StantaFe
Eonon GA9180A for Chevrolet/GMC
Autostereo for Mazda 5
Tested and compatible 3G/4G modems
ZTE MF622
ZTE MF825
Huawei e173
Huawei E352
Huawei E3272
Alcatel 410D
How to update firmware on the device (without changing android version)
I know at least 3 methods how to do that Use USB Stick or SD card with FAT32 filesystem for android 8 or USB Stick ONLY for android 9.
1.
- put the firmware (kupdate.zip + update2.bin if you want to upgrade MCU) directly to USB stick or SD card,
- insert it while the unit is running,
- click OK once suggestion to update appears.
2. The same as 1, but the last point is to start update from system settings
3. Use it, if you have a brick (bootloop)
- put the firmware (kupdate.zip + update2.bin if you want to upgrade MCU) directly to USB stick or SD card with FAT32 filesystem for android 8 or ONLY USB Stick for android 9.
- power off the device, insert USB stick or SD card for android 8 or ONLY USB Stick for android 9.
- press and hold power button and power on unit by switching on ACC in your car or enable power +12V on both red and yellow wire in case you doing that on the table. On some units use reset button instead.
- once the update is started, release the button.
WARNING! Firmware update will remove all your personal data and settings on the device!
If you observe the error like "header and footer of kupdate.zip does not correspond signature", just try to upgrade form another USB stick/SD card.
Upgrade from Android 8 to Andriod 9 (Using disassembling method)
For now it is needed to DISASSEMBLE the unit for upgrade! These actions are on your own responsibility!!!
0. You will need Windows PC/Laptop/Tablet for this procedure, please refer to guide from Chinese engineers here.
1. Install drivers from this archive
2. Short circuit the resistor to ground (there is a picture in guide)
3. Power on the unit
4. Connect USB (use Type-A male to Type-A male cable).
5. Flash the Android 9 data from this archive
6. Disconnect USB and power. Then power on the unit.
7. Enjoy
After these steps you'll be able to install any android 9 from this thread. It is needed to disassemble the unit only once.
A few videos for the reference are there and there.
Upgrade from Android 8 to 9 WITHOUT disassembling.
ALL YOUR ACTIONS ARE YOUR OWN RESPONSIBILITY!!! Nobody will send you a new core board in case of the failure! At least will not do that free of charge!
0. All needed files are there.
1. To perform the upgrade we need:
- Strong desire to do that and be ready to purchase a new core board in case of total failure (~100$);
- micro SD card slot in your unit. If the unit vendor gives details regarding the units without SD cards, I'll update this post;
- USB stick (up to 16GB, to avoid possible problems) formatted in fat32;
- micro SD card (again, please use not so big);
2. Put the following things on USB stick:
- MCU firmware that suits your device. I.e. update2.bin from the first message in thread with DSP or not depending on your unit)
- Android 9 firmware from the first message. kupdate.zip, Again: Andriod 9!!!
3. Do NOT plug USB stick to the unit for now, let`s make bootable SD card;
4. On Windows PC run SDDiskTool and create bootable SD card. The manual inside of the archive, with the details, so I see to reasons to repeat it there. update.img from the archive is used there ~350Mb;
5. Install "Android 8 upgrade 9.apk" into the unit, run it, click only the button in this application. The unit becomes a brick (temporary, till a success on step 9) - You will see only a black screen and lights on the buttons;
6. Put SD card into a units slot, disconnect battery terminal of your car or power off the unit in some other way. Both red and yellow wires of unit should not have +12V on them !!!
7. connect battery terminal.
8. The unit is upgraded for the first time. Take a video of the process!!! Just in case if you fail and it will be needed to troubleshoot that. On this step you should see TWO errors of formatting metadata. YES, there should be TWO errors!! and formatting error for system.
Video of attempt.
The final screenshot.
9. Disconnect and connect battery terminal one more time. The unit upgrades from SD card one more time Take a video of the process,just in case. this time there should be no errors with metadata and system!!! The last string should be "Doing Actions succeeded".
Video of 2nd attempt.
The final screenshot.
10. Disconnect battery terminal, REMOVE SD card from unit, plug USB stick prepared on step 2.
11. Connect battery terminal and the unit will complete the upgrade to Android 9.
12. Once the upgrade from USB stick is done, the unit start running Android 9. All further upgrades will be done from USB stick without any additional actions
Video of installing the firmware from USB Stick.
13. FORMAT SD card on your PC, do not use it in unit until it is formatted, just to be safe.
Upgrade to real android 10
There are 2 known ways how to upgrade to android 10.
1. Disassemble your unit and do the same as described there using the files for PX5 or PX6 depending on your platform. Also there is an instruction with pictures in each archive.
2. Without disassembling, but using windows laptop or tablet. Quite simple, but requires lots of checks and preparations. And in worth case scenario you will have to solder to the needed pins of coreboard.
!!! The upgrade is possible on motherboards rev 1.4, 1.5.2 and 1.6 (quite possible that other revisions too, but we have not enough information for now). The mainboards of rev 1.2 require disassembling and soldering additional usb cable!!!
In order to complete the upgrade we need:
- strong desire to do that and be ready to disassemble unit in case of the failure or even purchase a new one.
- USB type A male to type A male cable
- Windows laptop or tablet
Steps to do.
1. Preparation
- check the Bluetooth module that is configured in your unit: System Settings-->Factory Settings-->FUNC-->BT Mode. Note its model somewhere. That will be needed to restore the settings after the upgrade.
- check if you can do an upgrade:
-- install terminal emulator on your unit and run
Code:
dmesg | grep "USB device" | grep using
and note the last time stamp
-- plug USB stick to the first USB (on the panel or into an extender cable)
-- run again
Code:
dmesg | grep "USB device" | grep using
-- if you see something like
Code:
[ 4781.749803] usb 3-1: new high-speed USB device number 16 using usb20_otg
you can use this USB and plug the head unit to your laptop via it using USB male type A to male type A cable. usb20_otg is vital
-- if you see something like
Code:
1-1.3: new high-speed USB device number 5 using ehci-platform
This USB can not be used!
-- repeat the action for the second unit`s USB
-- IF BOTH PORTS DOES NOT HAVE OTG YOU CAN NOT GO FURTHER UNTIL YOU SOLDER THE 3RD CABLE! The instruction is at the end of this post.
- download PX5 or PX6 depending on your platform.
- if you have a display with resolution 1280*720 , download a custom oem.img, it is suitable for both PX5 and PX6;
- extract archive to root directore of drive C: You should have C:\px6_10.0_burntools\ or C:\px5_10.0_burntools\ folder;
- install drivers from DriverAssitant folder;
- in case of PX6 go to C:\px6_10.0_burntools\AndroidTool_Release_v2.71, for PX5 go to C:\px5_10.0_burntools\AndroidTool_Release_v2.71, edit config.ini, replace Selected=1 with Selected=2. That will enable English language for the program;
- if you have 1280*720 display, put the custom file to rockdev\image folder and replace the old one;
- backup all vital data on your head unit;
2. Upgrade
- run AndroidTool.exe
- download and install this APK
- run it and click "Go to Android10", the device will be rebooted and BRICKED. APK kills loader and boot partition!!!
- connect your laptop and head unit via the discovered OTG USB
- AndroidTool should reprt "Found one MASKROM device"
- hit run button;
- wait until the competition.
The unit will be rebooted, data partition will be formated and the unit will be running andriod 10.
3. Post upgrade
- download the most recent firmware
- put it on USB stick
- do an upgrade using this USB stick
Known issues and fixes
1. Bluetooth KD6 does not work on android 10. Replace the module with IVT140 or RF210, maybe it will be fixed in new firmware. Fixed starting from 202011261850
2. In some unique cases the rear camera does not work on android 10 (we suspect that it appears on old mainboard revisions without DSP). Fix is to revert to android 9 or maybe it will be fixed in new firmware. Fixed starting from 202010141730
TIPs.
Mainboards Rev 1.2 do not have USB OTG, so you have to solder the 3d USB cable. Just solder the USB wire to connector A if the mainboard. Pins 63 and 64. 63rd stands for D+, 64th corresponds D-. Do not forget about GND. +5V is not mandatory for upgrade, you can take it from rear connector H (check pin 5 or 10 there) and make fully working USB port.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Now we need TWRP and some proper custom ROM support.
February 20th 201902201912 + MCU CSN2_0192019_154914 from Pumpkin ND0294 suitable for us said:
I couldnt download the file, it comes corrupt.
---------- Post added at 01:51 PM ---------- Previous post was at 01:48 PM ----------
In my unit, buzz comes when the radio is off, and the noise seems like the radio was turned on, but in very low volume... Does it happen with you too, guys?
Click to expand...
Click to collapse
aecioms said:
I couldnt download the file, it comes corrupt.
Click to expand...
Click to collapse
Fixing my google drive.
aecioms said:
I couldnt download the file, it comes corrupt.
Click to expand...
Click to collapse
Fixed.
Does this unit permit firmware downgrade?
aecioms said:
Does this unit permit firmware downgrade?
Click to expand...
Click to collapse
If you are talking about downgrade from, let's say, Feb firmware to Dec firmware - it works. If you are looking some exotic android like 6.0, there is no firmware with old android for these units.
Head units RockChip PX5 with MCU CSN2 (Android 8.0.0): discussion, firmware, tips etc
_yuzo_ also add these skyshadow products. I own the 1st one with 64gb upgraded version
1. Adjustable 10.1" IPS Android 8.0 4GB +32GB + 8 Core Car DVD Player GPS Glonass map RDS Radio wifi Bluetooth 2 Din for universal
https://s.click.aliexpress.com/e/bSVJ1e80
Particularly the 64gb free upgraded versions were csn2
2. New IPS 10.1" Android 8.0 4GB +64GB + Octa Core Car DVD Player GPS Glonass map RDS Radio wifi Bluetooth 4.0 2 Din for universal
https://s.click.aliexpress.com/e/cncQMDNQ
Sent from my iPhone using Tapatalk
sambhasanbiswas said:
_yuzo_ also add these skyshadow products. I own the 1st one with 64gb upgraded version
Click to expand...
Click to collapse
Done.
Hi Yuzo. Do you know if there is a way to pull a copy of my existing OS and MCU that came shipped with the unit? I want to try flashing to the latest pumpkin MCU, but would like to restore to stock if needed. My unit is an Eonon GA9180a. Thanks!
Build Number: 201811021951
Kernel: 4.4.103
MCU: CSN2_1122018_153527
Guys, I can't transfer files with ES File explorer by WLAN. It says "sender disconnected"... Does it happen with someone else? How to solve this?
Now I need to use pendrive everytime I want to transfer files to headunit...
rblloyd83 said:
Hi Yuzo. Do you know if there is a way to pull a copy of my existing OS and MCU that came shipped with the unit? I want to try flashing to the latest pumpkin MCU, but would like to restore to stock if needed. My unit is an Eonon GA9180a. Thanks!
Build Number: 201811021951
Kernel: 4.4.103
MCU: CSN2_1122018_153527
Click to expand...
Click to collapse
Hi! Rooting app contains tools for backup, but that is rather alfa version and noone tried to flash that dump back.
Your MCU is present in very first firmware available there. I, as well as xda and 4pda users, do not have 201811021951 firmware. But I can assure that Jan 17th and Pumpkin firmwares are stable. The only noticeable difference between them is in a launcher, application appearance. Also Pumpkin does not have the option that allows to set the brightness according to the clock.
Please also share the link where you bought your device.
_yuzo_ said:
Hi! Rooting app contains tools for backup, but that is rather alfa version and noone tried to flash that dump back.
Your MCU is present in very first firmware available there. I, as well as xda and 4pda users, do not have 201811021951 firmware. But I can assure that Jan 17th and Pumpkin firmwares are stable. The only noticeable difference between them is in a launcher, application appearance. Also Pumpkin does not have the option that allows to set the brightness according to the clock.
Please also share the link where you bought your device.
Click to expand...
Click to collapse
Thanks, sure appreciate the feedback. I purchased this system:
"eonon.com/Android-Car-GPS/Vehicle-Specific-GPS/Chevrolet-GMC-Buick-Newest-Android-8-0-Car-GPS-Navigation-System-7-Inch-Auto-Stereo-Upgrade-RAM-4GB-Factory-Auto-Radio.html"
I just wanted to list my csn2 device that I ordered at aliexpress from seller autostereo for my Mazda 5: https://de.aliexpress.com/item/-/32913733250.html
I did not do any modification so far. But steeringwheel keys do double clicks, so maybe I will try some update later.
rblloyd83 said:
Thanks, sure appreciate the feedback. I purchased this system:
"eonon.com/Android-Car-GPS/Vehicle-Specific-GPS/Chevrolet-GMC-Buick-Newest-Android-8-0-Car-GPS-Navigation-System-7-Inch-Auto-Stereo-Upgrade-RAM-4GB-Factory-Auto-Radio.html"
Click to expand...
Click to collapse
Thanks. Added.
donny02 said:
I just wanted to list my csn2 device that I ordered at aliexpress from seller autostereo for my Mazda 5: https://de.aliexpress.com/item/-/32913733250.html
I did not do any modification so far. But steeringwheel keys do double clicks, so maybe I will try some update later.
Click to expand...
Click to collapse
Added to the list of devices. The case is connected with canbus adapter and fixed in Jan 17th firmware (also it is possible to fix that by changing wires, but firmware update is much easier). If you want to keep the original launcher - use Jan 17th firmware, otherwise you can try Pumpkin.
Eonon GA9180A For Chevy/GM Trucks is running CSN2. Im pretty sure its a klyde as well.
As for the static when D/L U/L over wifi. It because the wifi antenna is taped directly to the top of the am/fm receiver and not properly shielded.
I did buy a new antenna with a longer cable. One of these days i will pull it out of the truck and add the new one in and reroute the wiring to see if it helps any.(not in a rush since it doesn't bother me to much)
Hi there,
I got myself the following unit on aliexpress: https://de.aliexpress.com/item/4000805871840.html?spm=a2g0s.9042311.0.0.52ef4c4dBTvhGh. It has a CHS MTCE.
When I look at factory settings, it says "A-Media Auto" as device name.
It came with zlink Carplay PCB mounted on the PCB and worked with stock rom. When I changed to mod firmwares (e.g. HAL9k or Malysk) I actually lost the CarPlay functionality. zLink just stays at "waiting", however my phone identifies the unit as CarPlay available and connects over bluetooth using the carplay connection dialog. However the "use carplay now" dialog doesn't pop up. Manufacturer says, the unit would need to be returned to factory to reprogramme. Not sure this entirely the only option.
They said they don't offer the stock rom, just updates.
A friend of mine has bought exactly the same unit, so I was wondering if I could extract the OEM stock software from there and flash onto my unit. I am not an Android expert, however already changed a couple of iPhones/Tablets OEM software e.g. to LineageOS. So, with some turoials I normally find my way around. I am ok experienced on admin level on WIN and Linux.
Not sure the OEM Android is fully rooted, but I can find out, when I have the OEM unit in my hands.
Is there a (relatively safe) process to extract the stock rom and update the modded rom HU?
See my OTG thread, extract partition by partition from your friends unit, which you mention is the same, then flash your SOM.
Thanks for replying.
My SOM has an USB port soldered to it. (See photo). Chances are, I do not even use the "wire" method to connect, but just use this port?
wupperi said:
Thanks for replying.
My SOM has an USB port soldered to it. (See photo). Chances are, I do not even use the "wire" method to connect, but just use this port?
Click to expand...
Click to collapse
PX6 board has a HDMI connector on it - do you mean that?
I am also interested in a PX6 stock Android 9 partition export image, as I recently bought a PX6 board which has Android 10 preinstalled and therefore I am currently limited to it and can´t "downgrade" to my preferred ROM Hal9k v4 beeing Android 9 based...
Hi everybody.
I have an Ullgo hu with SC9853i processor,4 gbRAM and I searched for 9 months how to root, at the end I DO IT.
Here is my hu:
MCU VERSION Ts9.4.3-24-84-94C681-191021
SYSTEM VERSION V11.1.1_20200304.092444_AKW2-X
ANDROID 9
It's very simple:
Zip decompression.
Put the all the files on the usb stick(FAT 32 format), 3 files, NOT INSIDE of a folder.
Plug the usb stick to the radio.
Settings->car settings-> update firmware (don't touch other function), press ok on display and let the radio to do himself.
After his restart, let the stick usb connected,connect to wifi, install Magisk Manager, install Root Explore, in the Magisk Manager give permission to Root Explorer and it's done.
The root patch is taked from OWNICE C960 K6 head unit.
All the bests.
nick1964 said:
Hi everybody.
I have an Ullgo hu with SC9853i processor,4 gbRAM and I searched for 9 months how to root, at the end I DO IT.
Here is my hu:
MCU VERSION Ts9.4.3-24-84-94C681-191021
SYSTEM VERSION V11.1.1_20200304.092444_AKW2-X
ANDROID 9
It's very simple:
Zip decompression.
Put the all the files on the usb stick(FAT 32 format), 3 files, NOT INSIDE of a folder.
Plug the usb stick to the radio.
Settings->car settings-> update firmware (don't touch other function), press ok on display and let the radio to do himself.
After his restart, let the stick usb connected,connect to wifi, install Magisk Manager, install Root Explore, in the Magisk Manager give permission to Root Explorer and it's done.
The root patch is taked from OWNICE C960 K6 head unit.
All the bests.
Click to expand...
Click to collapse
works with ullgo android 8.1
SC9853i processor,4 gbRAM ?
is the android 9 in the head unit directly from sell or did you update
The hu show me Android 9, checked with Aida 64 tel me Android 8.1.
I receveid the hu with this fake Android 9.0, I don't update.
I think you can try.
Search Ownice C960 K6 root, you"ll find on Icar Vietnam forum (need google translate); you find the root for various firmware.
How I said talking about SC9853i with 4gb Ram, many Ullgo=Teyes=Ownice=Allwinner=Topway, that use the same mainboard (with very little differences).