Need some help - Strange OP6T storage issues after flash - OnePlus 6T Questions & Answers

Hello, I have a T-Mobile 6T which thanks to the XDA thread about bypassing T-mobile, is running the international firmware so I didn't have to kiss their butt trying to unlock the bootloader. Yesterday I decided to try the Resurrection Remix rom since it is unclear whether the Lineage 16 rom supports the in-display fingerprint reader, and I am too busy at work and too lazy to read the entire thread to see if it does.
I followed the instructions and updated my OxyOS to the latest .15 release via TWRP which I also updated to the latest version via OTG using a USB drive because I was unable to unencrypt using the older Blu-Spark TWRP version I had installed. After the OxyOS update (on both partitions) I flashed TWRP again, rebooted to recovery and installed Pico Gapps.
I found the Resurrection Remix rom to be very buggy and I hate the way the in-display biometric works (very slow and I don't like the paw print used as fingerprint placement). Anyway I started installing apps and after 4 apps installed, it says there is no space left in storage.
Nothing will update, and when I try to check storage with any file explorer it says "access denied" or just won't load. I've tried everything. Wiped the data and did factory reset, then flashed stock rom again and same issue. What am I doing wrong?

That looks like a messed up flash. And is pretty common. Considering that A/B is still new and everyone has his own method of flashing. So assuming you can make it back to latest Stock OOS (9.0.15 right now). If you dunno how to then simple reboot to recovery, flash OOS ZIP and then TWRP. Again Reboot to Recovery from within TWRP (Reboot -> Recovery) and again flash OOS ZIP and TWRP Installer. For TWRP I recommend you to grab the latest one (3.3.1-6 as of now). Once flashed, Format Data (Wipe -> Format Data -> YES) and Reboot. Wait for it to boot up. Now you should be on Stable Stock OOS with TWRP Installed.
Now Download ROM of your Choice (RR, LOS, Bootleggers, whatever). You will also need the latest TWRP Installer (same as above) and Gapps (Nano/ Stock Recommended) and Magisk if you want to Root. Reboot to Recovery, flash ROM ZIP and TWRP Installer ZIP. Wait for it to Finish. Reboot to Recovery. Once in TWRP, again flash ROM and TWRP Installer. Once done, again. Reboot to Recovery from Within TWRP. (Read above on how to). Now, flash Gapps. Magisk if you want to Root. Once done, again do a Format Data. Reboot and be patient for ROM to boot. And then tell me wether this works or Not. Good Luck.

Related

TWRP, Rom and GAPP issues?

I'm new to this device and already I'm extremely confused. I tried flashing TWRP the old school method and found out very fast that it was a no go. Upon reading around, I fount the following guide and booted TWRP:
https://forum.xda-developers.com/mi-a1/how-to/lineageos-gapps-magisk-twrp-dolbyatmos-t3762939
The problem? I can install DotOS, but as soon as I try to flash the GAPPS, I get an error (it claims that I am on 7.1.2, but I'm using the latest DotOS version which is 8.1.0 based). Since from what I understand the recovery seems to be tied to the boot.img (like the Sony Ericsson Xperia Play), I believed simply rebooting into recovery would help. Unfortunately this boots into stock recovery for 8.0.0 (mind you I was on 8.1.0 stock). Upon reading around on how to install TWRP on the phone itself, I found this thread:
https://forum.xda-developers.com/mi-a1/development/recovery-twrp-3-1-1-0-touch-recovery-t3688472
This is the bigger headache. After following the instructions which are clear as day, I encounter similar issues to half of the replies in that thread. Another issue is that there is no explanation on whether you should be on stock first or...? Secondly, nothing is said on which "slot" (a or b) to flash your desired rom. So my default slot was b, I switched to a to flash the TWRP installer and so on as per instructions. I then assume I am to switch back to slot b for my rom to be installed. The issue is that after trying to install the GAPPS, I am faced with the issue again of the 7.1.2 detected. The only way to get around this is to flash it in slot a, but then the device will never boot. I'm very confused?
Use this twrp. Then you flashed twrp, wipe, install ROM, reboot into recovery again and flash gapps.
Crossvxm said:
I'm new to this device and already I'm extremely confused. I tried flashing TWRP the old school method and found out very fast that it was a no go. Upon reading around, I fount the following guide and booted TWRP:
https://forum.xda-developers.com/mi-a1/how-to/lineageos-gapps-magisk-twrp-dolbyatmos-t3762939
The problem? I can install DotOS, but as soon as I try to flash the GAPPS, I get an error (it claims that I am on 7.1.2, but I'm using the latest DotOS version which is 8.1.0 based). Since from what I understand the recovery seems to be tied to the boot.img (like the Sony Ericsson Xperia Play), I believed simply rebooting into recovery would help. Unfortunately this boots into stock recovery for 8.0.0 (mind you I was on 8.1.0 stock). Upon reading around on how to install TWRP on the phone itself, I found this thread:
https://forum.xda-developers.com/mi-a1/development/recovery-twrp-3-1-1-0-touch-recovery-t3688472
This is the bigger headache. After following the instructions which are clear as day, I encounter similar issues to half of the replies in that thread. Another issue is that there is no explanation on whether you should be on stock first or...? Secondly, nothing is said on which "slot" (a or b) to flash your desired rom. So my default slot was b, I switched to a to flash the TWRP installer and so on as per instructions. I then assume I am to switch back to slot b for my rom to be installed. The issue is that after trying to install the GAPPS, I am faced with the issue again of the 7.1.2 detected. The only way to get around this is to flash it in slot a, but then the device will never boot. I'm very confused?
Click to expand...
Click to collapse
To install twrp, use twrp 3.2.3 from abishek (lineageOS) or from cosmicdan.
This phone have slot a/b. For installing twrp it doesn't matter from which slot you install as it will install in the boot partition, not in system.
First do facory reset, you don't have to be on stock.
For custom rom zip if you are in slot a it will be installed in the slot b. After installing rom install twrp again as it's deleted when you install new rom and change slot, reboot and install gapps according with the rom 8.1 or 9.0 and magisk, it installs on the same slot..
Cosmicdan twrp have an option to install rom zip on the same slot and have a survival option for twrp, so you don't have to install twrp when you install a rom or a new kernel.
ccalixtro said:
Use this twrp. Then you flashed twrp, wipe, install ROM, reboot into recovery again and flash gapps.
Click to expand...
Click to collapse
This is the link for twrp:
https://forum.xda-developers.com/mi-a1/development/treble-twrp-installer-treble-manager-t3793637
Reboot recovery after u flash rom, then flash gapps,magisk

What's the REAL method to successfully install a working TWRP, root and custom ROM?

Hi All, I have been reading various threads here and searching on Google for finding a method that truly works for successfully installing a custom ROM, getting TWRP installed and rooting with Magisk. So far, all I have found are numerous and usually contradictory methods and about 7 or 8 different versions of TWRP (so which one is completely stable and working properly?). I have tried several methods over the past two weeks and none of them are working completely.
Sometimes, I'll get a version of TWRP installed, but then trying to reboot to recovery results in a "system has been destroyed" image. Or I'll succeed in getting a custom ROM installed, but Gapps will fail with error 20 or error 70 or there's not enough space on the system partition (and I'm just trying to install the Pico version). Even I double check that the Gapps version matches the ROM version I've used, but still get an error 20 displayed.
From what I had read on numerous threads, it seemed like CosmicDans TWRP would be the one I should go with. I downloaded both of his files (the fastboot image and the zipped installer) and fastboot his "boot-recovery.img" that was specifically for fastboot only and from that recovery, I installed his "TWRP-Installer-3.2.1-with-Tissot-Manager-2.5.zip". Everything appeared as if successfully installed as per the logs, but immediately upon attempting to reboot to recovery, I get the "system has been destroyed" image.
What I want to do is:
Get a working custom ROM (preferably Pie) installed
Install Gapps
Install a working TWRP (that will not display "system has been destroyed" whenever trying to boot to recovery)
Finally, install Magisk and root my phone
Can anyone suggest a site or link or a post somewhere that would explain everything correctly and is actually working? This has been a very frustrating experience. I'm almost sorry that I even bought the Mi A1. Never had any problems installing custom ROMs or rooting the OnePlus devices. All I'm left with currently is an expensive paperweight.
Thanks so much!
Cheers
From your description, I'm certain that you do this on a Pie stock rom right? the installer never work on Pie stock and will cause system destroy. Just hotboot TWRP. And for the Gapps, I think it's due to the time you install it. From my experience, install Gapps after rom and before Magisk usually work. Install after magisk or custom kernel will somehow cause the same issue that you described.
Oh, in case you want to install LineageOS, you have to come to the LOS16 thread and download the TWRP from there, it's the only TWRP that can install LOS16.
Never_Sm1le said:
From your description, I'm certain that you do this on a Pie stock rom right? the installer never work on Pie stock and will cause system destroy. Just hotboot TWRP. And for the Gapps, I think it's due to the time you install it. From my experience, install Gapps after rom and before Magisk usually work. Install after magisk or custom kernel will somehow cause the same issue that you described.
Oh, in case you want to install LineageOS, you have to come to the LOS16 thread and download the TWRP from there, it's the only TWRP that can install LOS16.
Click to expand...
Click to collapse
Thank you for your reply. When I first started the process to change to a custom ROM, I was on stock Pie. But one of the times I was wiping the device after one more problem, I accidentally also wiped Internal Storage as well. I didn't have much there since I had already backed some things up in advance. Now it's virtually empty. The steps I take are:
1. Hotboot TWRP
2. Install Custom ROM
3. Hotboot TWRP again
4. Install Gapps
This is where I usually have some problem. It's the process of installing Gapps that creates some error.
I also did attempt to install LineageOS 16 using the TWRP recovery that was linked in the post. Follow the instructions precisely I believe and now when it's time to install Gapps, I get error 64. I can't understand why. I am attempting to install "open_gapps-arm64-9.0-nano". This should be compatible with the Mi A1 with LineageOS 16 from what I am able to tell.
No matter what TWRP version I use, no matter what custom ROM I try, no matter what steps I take, there is always some issue that prevents me from completing any installation. But the abundance of so many conflicting posts don't help either. One post will state to use a specific TWRP and certain steps; another post will suggest completely different steps using another TWRP; and yet another post will provide different steps still. In some instances, there will be steps listed in the script on the phone regarding the next steps after the ROM installation that are completely different then the steps provided in the post for that ROM in the forum.
It would just be tremendously helpful to get some instructions that actually do work. As of now, I'm about ready to dump this phone in the trash bin. It's horrible. I can't even tell if it might be decent eventually since I never can get anything installed.
Thanks again for your reply Never_Sm1le.
Cheers.
There is no permanent TWRP install for android 9 on MiA1 as far as i know.
Hotboot works just perfect.
Brianne8 said:
Thank you for your reply. When I first started the process to change to a custom ROM, I was on stock Pie. But one of the times I was wiping the device after one more problem, I accidentally also wiped Internal Storage as well. I didn't have much there since I had already backed some things up in advance. Now it's virtually empty. The steps I take are:
1. Hotboot TWRP
2. Install Custom ROM
3. Hotboot TWRP again
4. Install Gapps
This is where I usually have some problem. It's the process of installing Gapps that creates some error.
I also did attempt to install LineageOS 16 using the TWRP recovery that was linked in the post. Follow the instructions precisely I believe and now when it's time to install Gapps, I get error 64. I can't understand why. I am attempting to install "open_gapps-arm64-9.0-nano". This should be compatible with the Mi A1 with LineageOS 16 from what I am able to tell.
No matter what TWRP version I use, no matter what custom ROM I try, no matter what steps I take, there is always some issue that prevents me from completing any installation. But the abundance of so many conflicting posts don't help either. One post will state to use a specific TWRP and certain steps; another post will suggest completely different steps using another TWRP; and yet another post will provide different steps still. In some instances, there will be steps listed in the script on the phone regarding the next steps after the ROM installation that are completely different then the steps provided in the post for that ROM in the forum.
It would just be tremendously helpful to get some instructions that actually do work. As of now, I'm about ready to dump this phone in the trash bin. It's horrible. I can't even tell if it might be decent eventually since I never can get anything installed.
Thanks again for your reply Never_Sm1le.
Cheers.
Click to expand...
Click to collapse
Your reply makes me want to stay on LOS 15.1 even more. So many weird problems happen in LOS 16
I followed all the instructions of Resurrection Remix and TWRP is installed and magisk works perfect.
Hello friend, I am currently on Lineage OS 16.0 with Magisk, Opengapps and TWRP installed. I can boot to recovery with no problems at all; in fact, I used the flashed TWRP to install Magisk.
Here are the steps I took:
Download the TWRP boot img and TWRP installer by CosmicDan (Link below)
Copy the custom rom ZIP, TWRP installer, Magisk installer and Gapps into your SD card
Reboot your device to bootloader
Boot into TWRP using
Code:
fastboot boot boot-recovery.img
do NOT flash via fastboot
Go to Wipe>Advanced Wipe and wipe System, Dalvik, Data, Internal Storage
Press the home button and proceed to flashing the custom rom ZIP
After flashing, reboot to BOOTLOADER then do step 4 again
Flash Gapps, TWRP Installer, then Magisk Installer. You should flash TWRP first before Magisk
Reboot to system and you're good to go
Note that if you are installing Lineage OS and wish to receive nightly OTA updates, having an installed TWRP as your recovery might result in a bootloop after updating. Also, if you want to manually flash the nightly update, you need to boot to the TWRP variant of @flex1911 as flashing lineage using other TWRP will result in an error. I suggest not installing TWRP when using Lineage OS.
(Source: [ROM][OFFICIAL] LineageOS 16.0 for Xiaomi Mi A1)
Regarding your problem with flashing, try to check which slot you are currently in by going to TWRP>Reboot. Keep in mind that when you install a rom, it will always be installed to the inactive slot. For example if you are in slot A, your rom will be installed in slot B. After rebooting, your current active slot will be where the rom is installed. When installing Gapps or any addons, check the slot first. However, when flashing TWRP installer, it will patch both boot_a and boot_b and this is the reason why you need to install twrp first before magisk as TWRP also modifies the boot image.
Download:
Bootable TWRP
TWRP Installer
(Both files by @CosmicDan)
Cheers mate!
rexendz said:
Here are the steps I took:
Download the TWRP boot img and TWRP installer by CosmicDan (Link below)
Copy the custom rom ZIP, TWRP installer, Magisk installer and Gapps into your SD card
Reboot your device to bootloader
Boot into TWRP using
Code:
fastboot boot boot-recovery.img
do NOT flash via fastboot
Go to Wipe>Advanced Wipe and wipe System, Dalvik, Data, Internal Storage
Press the home button and proceed to flashing the custom rom ZIP
After flashing, reboot to BOOTLOADER then do step 4 again
Flash Gapps, TWRP Installer, then Magisk Installer. You should flash TWRP first before Magisk
Reboot to system and you're good to go
Click to expand...
Click to collapse
Thanks for the lengthy reply. However, those steps do not work as you have described. Since, if I wipe Internal Storage (as per your step 5), I just deleted all the files I copied previously in Step 2. What I did, was wipe everything, *then* copied all the files and tried to install. As soon as it try to install Gapps, I get Error 64 again. I am absolutely using "open_gapps-arm64-9.0-nano" and it always fails. I have attempted 11 or 12 times already, using different slots, using different dates of "open_gapps-arm64-9.0-nano" and ALWAYS Error 64. I don't know any other version of Gapps I should be trying. The arm64 versions never will work for me.
I give up. I'll just have to stick with stock ROM. No custom ROMs will work for me no matter which one I use or which version of TWRP I use. I already wasted too much of my life with this garbage phone.
ccalixtro said:
I followed all the instructions of Resurrection Remix and TWRP is installed and magisk works perfect.
Click to expand...
Click to collapse
Hi,
Which version of TWRP did you use? There's too many. I don't know which one is considered to be the right one.
Brianne8 said:
Thanks for the lengthy reply. However, those steps do not work as you have described. Since, if I wipe Internal Storage (as per your step 5), I just deleted all the files I copied previously in Step 2. What I did, was wipe everything, *then* copied all the files and tried to install. As soon as it try to install Gapps, I get Error 64 again. I am absolutely using "open_gapps-arm64-9.0-nano" and it always fails. I have attempted 11 or 12 times already, using different slots, using different dates of "open_gapps-arm64-9.0-nano" and ALWAYS Error 64. I don't know any other version of Gapps I should be trying. The arm64 versions never will work for me.
I give up. I'll just have to stick with stock ROM. No custom ROMs will work for me no matter which one I use or which version of TWRP I use. I already wasted too much of my life with this garbage phone.
Click to expand...
Click to collapse
Copy the files to your external SD card not internal storage. But if you don't have an ext SD card, don't wipe internal storage.
Also try to check if system is properly mounted when installing gapps.
May I ask what custom rom you are trying to install?
I suggest you try Pixel Experience as it already has a builtin Gapps so you dont have to flash opengapps.

please help. tried to flash OTA and now i cant get back to OS

hey guys, so i used twrp to flash a OTA then flashed twrp again and rebooted and when i went to flash magisk i was just shown a list of all random numbers/letters. i booted into bootloader flashed twrp img, booted into recovery and all my files were there once again but i still cant get into the OS, can anyone please help?
why is flashing so complicated these days? even the recovery works different. the last time i rooted (4 years ago maybe) you could use twrp to make a backup and it was done simple as that (i did this on the oneplus 6t about 4 weeks ago and got the issue with my storage just being a list of numbers and letters and had to find a way to fully wipe and re install OOS) and the same for flashing, i could just flash something and it was fine, no issues.
Do you have an OTG adapter and pendrive? You can copy the full OTA zip, TWRP zip and Magisk zip on to that and flash from TWRP using that. Your internal storage is encrypted and you won't be able to access it until you can reboot OOS fully. If that didn't work, you may have to do a factory reset/wipe (including internal data) to get the phone to boot again. You will obviously lose any unbacked data.
Which version of TWRP are you using? Which version of OOS are you using? Most likely you just don't have the correct version, and you updated to the latest version OOS with the new security patch and it no longer can decrypt it.
Have you tried TWRP 3.3.1-7 from here? If you boot the .img file from fastboot, can you decrypt your data?
Most likely you just need to flash Magisk, and you will be fine. For updates, it's always as you did, flash the full OTA update, TWRP installer, reboot to recovery, Magisk. It is recommended to uninstall Magisk, however I usually don't do that personally. Official Instructions here. You just have to make sure you are using the correct version of TWRP, otherwise you can run into encryption issues, as you found out when there are updates.
OhioYJ said:
Which version of TWRP are you using? Which version of OOS are you using? Most likely you just don't have the correct version, and you updated to the latest version OOS with the new security patch and it no longer can decrypt it.
Have you tried TWRP 3.3.1-7 from here? If you boot the .img file from fastboot, can you decrypt your data?
Most likely you just need to flash Magisk, and you will be fine. For updates, it's always as you did, flash the full OTA update, TWRP installer, reboot to recovery, Magisk. It is recommended to uninstall Magisk, however I usually don't do that personally. Official Instructions here. You just have to make sure you are using the correct version of TWRP, otherwise you can run into encryption issues, as you found out when there are updates.
Click to expand...
Click to collapse
Latest twrp and latest full OOS OTA. If I fastboot the twrp. Img I can see all my data again. I've fixed it now, I flashed the twrp. Img in fastboot then rebooted system and it worked

Flash custom ROM

From 6T (purchased from oneplus.com), any time I follow the instructions for how to flash one of the custom ROMs, I get stuck at the bootloader with no working rom.
I was able to use the MSMTool to restore to 9.0.13. I upgraded a few times flashing OnePlus6TOxygen_34_OTA_024_all_1909112343_9fd6e0057b8747dc, which works, but when I try to flash a custom ROM, I cannot get past the bootloader. I say a few times because I've tried this for a few days now with no success.
Most recently, I used the Flash-all.bat inside 10.3.0-OnePlus6TOxygen_34_OTA_042_all_1912142031_d9ef3-FASTBOOT
I am currently on 10.3.0, with twrp-3.3.1-31-fajita-Q-mauronofrio installed using the fastboot flash boot_a twrp-3.3.1-31-fajita-Q-mauronofrio.img then fastboot boottwrp-3.3.1-31-fajita-Q-mauronofrio.img commands from fastboot.
I can then install Magisk 19.4 or 20.3, however again when I try to flash a custom ROM, I cannot get past the bootloader.
What am I doing wrong?
When you 'fastboot boot' twrp, you can't flash twrp as .img file after that..... (There is no recovery partition on our phone, only a boot one)
If you flash a twrp img it will overwrite boot partition with only twrp and no kernel... Basic knowledge. Once temporarily booted in twrp by 'fastboot boot' command you must flash the installer, meaning the .zip file.
Then reboot your phone in twrp and flash whatever you want
Always latest versions of Magisk, why flashing a deprecated 19.4?
Striatum_bdr said:
When you 'fastboot boot' twrp, you can't flash twrp as .img file after that..... (There is no recovery partition on our phone, only a boot one)
If you flash a twrp img it will overwrite boot partition with only twrp and no kernel... Basic knowledge. Once temporarily booted in twrp by 'fastboot boot' command you must flash the installer, meaning the .zip file.
Then reboot your phone in twrp and flash whatever you want
Always latest versions of Magisk, why flashing a deprecated 19.4?
Click to expand...
Click to collapse
I was having an issue with the boot command in 10.3.0, which is how I found the flash command, and using both of those seemed to work (at least get me into twrp).
Now I am able to just run fastboot boot twrp-3.3.1-31-fajita-Q-mauronofrio.img and it works.
I was using 19.4 because somewhere in here someone mention twrp not working with magisk 20.3.
I've had no issues with 20.3 and twrp, so I will continue to use 20.3
The steps I use to flash a custom ROM (after twrp is installed)
1. remove the lock screen security from the existing ROM
2. boot straight into recovery from the existing ROM
3. wipe Data, Cache, and Dalvik by swiping right to factory reset from the wipe menu
4. flash the ROM from internal storage using the Install button
at this point I've tried a couple of approaches including a reboot here to see if the ROM flashed, and also installing twrp right after flashing ROM so that I will have a working twrp install.
Either way, I can never get past the bootloader.
Am I performing these steps correctly?
s7itch3s said:
I was having an issue with the boot command in 10.3.0, which is how I found the flash command, and using both of those seemed to work (at least get me into twrp).
Now I am able to just run fastboot boot twrp-3.3.1-31-fajita-Q-mauronofrio.img and it works.
I was using 19.4 because somewhere in here someone mention twrp not working with magisk 20.3.
I've had no issues with 20.3 and twrp, so I will continue to use 20.3
The steps I use to flash a custom ROM (after twrp is installed)
1. remove the lock screen security from the existing ROM
2. boot straight into recovery from the existing ROM
3. wipe Data, Cache, and Dalvik by swiping right to factory reset from the wipe menu
4. flash the ROM from internal storage using the Install button
at this point I've tried a couple of approaches including a reboot here to see if the ROM flashed, and also installing twrp right after flashing ROM so that I will have a working twrp install.
Either way, I can never get past the bootloader.
Am I performing these steps correctly?
Click to expand...
Click to collapse
I don't know I don't flash custom ROMs anymore, too old for that stuff and need my time for me.
There are specific instructions for each custom ROM it's better to ask in dedicated threads, some of them need to have OOS in both slots before, some of them need to be fleshed in both slots. Normally you eventually wipe things, flash the ROM and twrp to keep it, then reboot to twrp (necessary to boot on the slot where the ROM is actually fleshed, which is always the non active slot, which become the new active slot) and flash Gapps and Magisk ( because Gapps and Magisk can be flashed only in active slot) then reboot system
s7itch3s said:
Am I performing these steps correctly?
Click to expand...
Click to collapse
I've updated these instructions here, they are the same, just added to them really.
This is how I install Lineage 17. (If you are doing 16, replace 10.3.0 with 9.0.17, and the Q image of TWRP with the Pie image)
- Install 10.3.0 fastboot ROM again to start over, boot it once. Just to make sure everything is good.
- Reboot to fastboot.
- Boot the Q image of TWRP.
- Run the TWRP installer, reboot to recovery
- You backed everything up right?
- Factory reset (This is the slider at the bottom in the wipe menu).
- Format data. (This is the button that says Format data in the wipe menu)
- Do NOT wipe cache, do not Wipe system, do NOT Wipe Dalvik / ART, do not add anything else, Just Factory Reset and Format Data. After doing those two Reboot to Recovery one more time. You must do this after formatting data.
- Now transfer Lineage and TWRP to your phone, Windows / Linux should see TWRP fine as a media device when plugged in.
- Install Lineage
- Run the TWRP Installer.
- Reboot to Recovery.
- Install Lineage (You need Lineage on both slots, so yes run it again)
- Run the TWRP Installer (yes again).
- Reboot to Recovery.
- Install Gapps if you want them.
- Install Magisk 20.3 if you use Magisk. I used 20.3 it works fine. (20.4 also fine) Do not install modules or other add ons at this point. Boot once and go through the setup and everything, then install your add-ons.
- Be aware the phone will restart once, then Lineage will start up and all will be good.
From that point on updating should just be like normal :
- Reboot to recovery
- Flash Lineage.
- Flash TWRP Installer
- Reboot to Recovery
- Flash Gapps. (Assuming you use them, if you installed them once you must continue to install them or do a clean install)
- Flash Magisk. (If you use it)
- Reboot to system.
- No loss of data, or anything.
- No need to flash anything twice etc.
I've posted similar instructions here. It was just for LOS 16, same thing essentially though.
OhioYJ said:
I've updated these instructions here, they are the same, just added to them really.
This is how I install Lineage 17. (If you are doing 16, replace 10.3.0 with 9.0.17, and the Q image of TWRP with the Pie image)
- Install 10.3.0 fastboot ROM again to start over, boot it once. Just to make sure everything is good.
- Reboot to fastboot.
- Boot the Q image of TWRP.
- Run the TWRP installer, reboot to recovery
- You backed everything up right?
- Factory reset (This is the slider at the bottom in the wipe menu).
- Format data. (This is the button that says Format data in the wipe menu)
- Do NOT wipe cache, do not Wipe system, do NOT Wipe Dalvik / ART, do not add anything else, Just Factory Reset and Format Data. After doing those two Reboot to Recovery one more time. You must do this after formatting data.
- Now transfer Lineage and TWRP to your phone, Windows / Linux should see TWRP fine as a media device when plugged in.
- Install Lineage
- Run the TWRP Installer.
- Reboot to Recovery.
- Install Lineage (You need Lineage on both slots, so yes run it again)
- Run the TWRP Installer (yes again).
- Reboot to Recovery.
- Install Gapps if you want them.
- Install Magisk 20.3 if you use Magisk. I used 20.3 it works fine. (20.4 also fine) Do not install modules or other add ons at this point. Boot once and go through the setup and everything, then install your add-ons.
- Be aware the phone will restart once, then Lineage will start up and all will be good.
From that point on updating should just be like normal :
- Reboot to recovery
- Flash Lineage.
- Flash TWRP Installer
- Reboot to Recovery
- Flash Gapps. (Assuming you use them, if you installed them once you must continue to install them or do a clean install)
- Flash Magisk. (If you use it)
- Reboot to system.
- No loss of data, or anything.
- No need to flash anything twice etc.
I've posted similar instructions here. It was just for LOS 16, same thing essentially though.
Click to expand...
Click to collapse
Sir, apology for being an old noob, I am on OOS 10.3.2 TWRP 3.3.1-32 can I follow the above guide? If Yes,
Why aren't we using the "Lineage Recovery" provided in "Lineage OS Downloads" page?? If we use it, will the above instructions change ? What are the cons of using it?
Sorry again for asking!! Can you please share me the Link to Open Gapps which Will be suitable in my scenario ?
Advised Sloth said:
Sir, apology for being an old noob, I am on OOS 10.3.2 TWRP 3.3.1-32 can I follow the above guide? If Yes,
Why aren't we using the "Lineage Recovery" provided in "Lineage OS Downloads" page?? If we use it, will the above instructions change ? What are the cons of using it?
Sorry again for asking!! Can you please share me the Link to Open Gapps which Will be suitable in my scenario ?
Click to expand...
Click to collapse
Historically Lineage / CM recovery was hit or miss, or TWRP or other recoverys worked better. To be fair I haven't even tried the Lineage recovery. So maybe that is no longer true? Right now, I know TWRP works. The updated instructions link up there has links in it, FYI, link OpenGapps. OpenGapps can be found here. You will be using Arm64, Android 10 obviously.
Since you are already on 10.3.2 (I assume you were on 10.3.1 before) you should be good to skip the step about fastboot ROM or install OOS, and you already have TWRP., so you should be able to go right on to backing everything up, wiping everything, and installing Lineage. (So you can skip the first few steps)
Anymore questions feel free to ask.
OhioYJ said:
Historically Lineage / CM recovery was hit or miss, or TWRP or other recoverys worked better. To be fair I haven't even tried the Lineage recovery. So maybe that is no longer true? Right now, I know TWRP works. The updated instructions link up there has links in it, FYI, link OpenGapps. OpenGapps can be found here. You will be using Arm64, Android 10 obviously.
Since you are already on 10.3.2 (I assume you were on 10.3.1 before) you should be good to skip the step about fastboot ROM or install OOS, and you already have TWRP., so you should be able to go right on to backing everything up, wiping everything, and installing Lineage. (So you can skip the first few steps)
Anymore questions feel free to ask.
Click to expand...
Click to collapse
First of all, thank you very much for your time and explanation.
Sir, so i will proceed as follows:
* Boot into TWRP Recovery
* Perform "swipe to factory reset" & "swipe to wipe data"
* Reboot to TWRP recovery again
* Flash LOS 17.1 on slot A
* Reboot to TWRP recovery again
* Flash LOS 17.1 on slot B
* Reboot to system
Sir, please check are my steps correct? If not,
From which step( steps mentioned in your guide) should i start?
Last query is, which GApps zip will be best for me, micro/nano/pico/tv stock, If i want max coverage of google?
Very sorry for knocking you repeatedly!!!
Advised Sloth said:
First of all, thank you very much for your time and explanation.
Last query is, which GApps zip will be best for me, micro/nano/pico/tv stock, If i want max coverage of google?
Click to expand...
Click to collapse
Your starting point is correct. However make sure you don't miss the re-install TWRP after flashing Lineage each time, and the second time you need to flash Gapps before you reboot to system.
Personally I always do Nano. Anything else you need (that would be included in Micro) can be installed from the Play store. Nano at least includes all the things that can't be installed from the play store.
Pico has the least in it. TV is for TV devices. On OpenGapps there is a box next to each package you can click and it will tell you exactly what is in each package.
OhioYJ said:
I've updated these instructions here, they are the same, just added to them really.
This is how I install Lineage 17. (If you are doing 16, replace 10.3.0 with 9.0.17, and the Q image of TWRP with the Pie image)
- Install 10.3.0 fastboot ROM again to start over, boot it once. Just to make sure everything is good.
- Reboot to fastboot.
- Boot the Q image of TWRP.
- Run the TWRP installer, reboot to recovery
- You backed everything up right?
- Factory reset (This is the slider at the bottom in the wipe menu).
- Format data. (This is the button that says Format data in the wipe menu)
- Do NOT wipe cache, do not Wipe system, do NOT Wipe Dalvik / ART, do not add anything else, Just Factory Reset and Format Data. After doing those two Reboot to Recovery one more time. You must do this after formatting data.
- Now transfer Lineage and TWRP to your phone, Windows / Linux should see TWRP fine as a media device when plugged in.
- Install Lineage
- Run the TWRP Installer.
- Reboot to Recovery.
- Install Lineage (You need Lineage on both slots, so yes run it again)
- Run the TWRP Installer (yes again).
- Reboot to Recovery.
- Install Gapps if you want them.
- Install Magisk 20.3 if you use Magisk. I used 20.3 it works fine. (20.4 also fine) Do not install modules or other add ons at this point. Boot once and go through the setup and everything, then install your add-ons.
- Be aware the phone will restart once, then Lineage will start up and all will be good.
From that point on updating should just be like normal :
- Reboot to recovery
- Flash Lineage.
- Flash TWRP Installer
- Reboot to Recovery
- Flash Gapps. (Assuming you use them, if you installed them once you must continue to install them or do a clean install)
- Flash Magisk. (If you use it)
- Reboot to system.
- No loss of data, or anything.
- No need to flash anything twice etc.
I've posted similar instructions here. It was just for LOS 16, same thing essentially though.
Click to expand...
Click to collapse
Sorry for the necropost, but this also works for TWRP 3.6 and Lineage 18.1. I initially had a problem with the default TWRP for my 6t. During the initial TWRP fastboot the version on their site caused a firmware error which I could just barely get out of, but it screwed up the system boot process in some subtle way that even the fixed version of TWRP (found on this site) couldn't solve.
After trying your instructions above, it didn't work the first time because of the screwed up system boot. It just kept trying to boot to recovery. I suspected a firmware error and was almost going to do an mcmdownload soft-brick rescue. I tried one last thing, using the TWRP on the system to sideload the stock ROM. That worked and patched up the system boot process. Once I booted and ran through some basic initialization to make sure developer options were properly set I followed the above instructions and it worked nearly flawlessly.
One strange thing. After I installed Lineage 18.1 and TWRP to both partitions (as well as Gapps / magisk), it rebooted to system and almost booted without incident -- except a large circular logo popped up that said 100% and stopped. I figured that that meant someting completed properly, so I powered off, waited 10 seconds, powered on and then the Lineage green system initialization spinner came up for a few minutes and it went through the user initialization sequence.
Thanks. I almost gave up and bought a new phone.
OhioYJ said:
I've updated these instructions here, they are the same, just added to them really.
This is how I install Lineage 17. (If you are doing 16, replace 10.3.0 with 9.0.17, and the Q image of TWRP with the Pie image)
- Install 10.3.0 fastboot ROM again to start over, boot it once. Just to make sure everything is good.
- Reboot to fastboot.
- Boot the Q image of TWRP.
- Run the TWRP installer, reboot to recovery
- You backed everything up right?
- Factory reset (This is the slider at the bottom in the wipe menu).
- Format data. (This is the button that says Format data in the wipe menu)
- Do NOT wipe cache, do not Wipe system, do NOT Wipe Dalvik / ART, do not add anything else, Just Factory Reset and Format Data. After doing those two Reboot to Recovery one more time. You must do this after formatting data.
- Now transfer Lineage and TWRP to your phone, Windows / Linux should see TWRP fine as a media device when plugged in.
- Install Lineage
- Run the TWRP Installer.
- Reboot to Recovery.
- Install Lineage (You need Lineage on both slots, so yes run it again)
- Run the TWRP Installer (yes again).
- Reboot to Recovery.
- Install Gapps if you want them.
- Install Magisk 20.3 if you use Magisk. I used 20.3 it works fine. (20.4 also fine) Do not install modules or other add ons at this point. Boot once and go through the setup and everything, then install your add-ons.
- Be aware the phone will restart once, then Lineage will start up and all will be good.
From that point on updating should just be like normal :
- Reboot to recovery
- Flash Lineage.
- Flash TWRP Installer
- Reboot to Recovery
- Flash Gapps. (Assuming you use them, if you installed them once you must continue to install them or do a clean install)
- Flash Magisk. (If you use it)
- Reboot to system.
- No loss of data, or anything.
- No need to flash anything twice etc.
I've posted similar instructions here. It was just for LOS 16, same thing essentially though.
Click to expand...
Click to collapse
OhioYJ, these are great instructions but it initially left me with questions about how that procedures would create duplicate installs on slot A and B. The answer is of course that the Lineage installer for the 6t knows about the dual slot setup and always writes to the inactive slot. Booting into recovery activates the inactive slot so that installing again after that installs to the other slot and now you have Lineage on both slots. The installer for TWRP always installs to both slots and is needed because Lineage always installs its recovery handler and you don't want that so you overwrite.
PS: TWRP has an option for installing itself after installing the requested package. Would that be just as good as installing the TWRP zip?
PPS: I had to do an 'adb push' of the Lineage and TWRP zips to sdcard for the installs. Unfortunately installing and slot switching makes the sdcard unavailable so you have to push the zips again. Is there somewhere I can write them to that I don't lose access to after a boot to recovery?

TWRP 3.5 on OnePlus 6T?

Title says it all. I've recently tried to install TWRP on 6T (latest OOS) but little to no avail. I was wondering has anyone have success with upgrading from 3.4 to 3.5 while keeping data? and if you have could you guide me into the steps that you have done to fully get the TWRP working?
No issues here, booted to twrp and flashed latest twrp installer, then magisk if you want root
@Huskied I used the themed One Plus TWRP located here on my Oneplus 6T. https://forum.xda-developers.com/t/...-twrp-by-acuicultor-morphine1.3847752/page-10
It's on the last page if interested. I'm currently using v3.5.2-9 from there. Zero issues installing it on my end.
Flash TWRP installer zip through TWRP on your device then reboot. You should have TWRP installed then.
On my global Oneplus 6t .
Rom install w/TWRP install:
Flash OOS 10.3.9
Flash rom (with gapps included as example)
Flash TWRP installer zip
Flash finalize
Reboot recovery
Flash magisk 22.1 zip
Format data (swipe yes) wipes everything!
Reboot system.
If you just want TWRP then just install installer zip and if you want root install magisk zip afterwards then reboot. Should be good then.
(Edit)

Categories

Resources