My cell phone brick, I did the qfil procedures but the same thing continues, the cell vibrates, the pc recognizes but the screen does not turn on, someone can help
Related
I seem to have hard bricked my Redmi Note 4g.
It does not get detected on my PC.
Nothing loads or shows up on the phone. Its completely dead.
When i connect the cable to my PC the red LED blinks just once. Nothing else.
Please Help
can you goto fastboot mode?
most MTK phones have testpoint where you have to jumping the wire from point A to point B and it will trigger preloader driver in sp flash tool. I didnt know where the point is but you can google it or ask someone in gsmhosting forum.
i have redmi note 4G gucii dual sim, but it's stuck in edl mode all the time, the flash is successful but it's still bricked in edl mode... what's the solution...?
i beg your help..
Finally I bricked the rn4 and reading this thread
After installing all the drivers and the flash tool the most important step is to boot the phone into edl mode or 9008 port which is very tricky step
STEPS:-
1. Power off the phone completely.
2. Press the volume up button for almost 15 sec without leaving press the power button for .5 sec (don't leave the volume button).
3. Again press the power button and hold it and immediately put the cable into the pc .
(note:- these time two buttons are pressed power button and the volume up button which was pressed in step two)
4. Leave both buttons when you receive the connection sound on the pc and check in the device manager now you connected to
the 9008 port instead of the 900E port.
(note:- step 4 can be symbolizes as you will get zuk logo flashed for a split of second after connecting the cable to the pc and
after that whole screen will be black and then after leave all the buttons and flash the phone with qpst)
refference:-http://forums.easy-firmware.com/showthread.php?97902-Lenovo-ZUK-Z2-Plus-EDL-Mode-And-Flashing-Process
how to turn off the phone completely while this phone hard bricked? im a noob, sorry
Aldhryy said:
how to turn off the phone completely while this phone hard bricked? im a noob, sorry
Click to expand...
Click to collapse
Press the power button for long time about 15-20sec until notification led gose off
Additional, some bricked devices may stuck in 900E mode, just keep on pressing in power botton and your device will reboot(screen may still be black, u must stare at the display of mode of your QFIL tool) .After rebooting some times(8∽9 times normally), your device will force boot into 9008 mode (you have to release the botton in a very short time or retry above lol) .
This method isnt from me and just tested on my phone succeefull .Hope helpful to someone.
Zuk Z2 Pro Stuck in EDL HS-USB 9008 Port and automatically connecting and disconnect
Hi,
My Zuk Z2 Pro is stuck in EDL 9008 Port. Phone is totally bricked and no sound, no light, no vibration. When i connect with the computer, phone is connecting on HS USB 9008 port and get disconnected after 20-22 seconds and again automatically connected with in half second time.
I am facing this issue after flashing a ZUI 1.9 by using a QPAST/QFIL application. I think i have made stupid mistake by flashing a phone with "ERASE ALL BEFORE DOWNLOAD" option.
I have tried every scenario to get stable this 9008 port but no luck. Since last 5 days i am studying forums and applying every kind of solution but same result.
I am writing this post with high expectations and hope someone will take notice and help me to get rid of this problem.
I can pay through paypal if someone wants to provide professional services to resolve this matter
I will appreciate if someone have any idea and can help me. Thanks
Farazk said:
Hi,
My Zuk Z2 Pro is stuck in EDL 9008 Port. Phone is totally bricked and no sound, no light, no vibration. When i connect with the computer, phone is connecting on HS USB 9008 port and get disconnected after 20-22 seconds and again automatically connected with in half second time.
I am facing this issue after flashing a ZUI 1.9 by using a QPAST/QFIL application. I think i have made stupid mistake by flashing a phone with "ERASE ALL BEFORE DOWNLOAD" option.
I have tried every scenario to get stable this 9008 port but no luck. Since last 5 days i am studying forums and applying every kind of solution but same result.
I am writing this post with high expectations and hope someone will take notice and help me to get rid of this problem.
I can pay through paypal if someone wants to provide professional services to resolve this matter
I will appreciate if someone have any idea and can help me. Thanks
Click to expand...
Click to collapse
1. Try uninstalling all the drivers you installed.
2.switch of your phone compeletly.
3.follow the link.
https://www.google.co.in/amp/s/foru...ecover-hard-bricked-zuk-z2-plus-t3576007/amp/
Solved: Zuk Z2 Pro Stuck in EDL 9008 mode and port auto connecting/disconnecting
[email protected] said:
1. Try uninstalling all the drivers you installed.
2.switch of your phone compeletly.
3.follow the link.
https://www.google.co.in/amp/s/foru...ecover-hard-bricked-zuk-z2-plus-t3576007/amp/
Click to expand...
Click to collapse
The Problem is resolved. I charged my battery 7-8 Hours and flashing done at first attempt. My phone was stuck in EDL mode and Port 9008 was continues connecting /disconnecting and i was not able to complete a flashing process. Flashing by using Qfil really sucked a battery. So if someone face such kind of issue, please charge your battery for 7-8 Hours and then try flashing.
Aldhryy said:
how to turn off the phone completely while this phone hard bricked? im a noob, sorry
Click to expand...
Click to collapse
The phone turns off completely when there's nothing on-screen (no error), notification, and no vibration
Hey, how are you?
Well, I tell you my problem.
It turns out that some time ago I was damaged and my LG P700 logo with its ROM Stock stuck in me, after that I tried to flahear with the KDZ but when I had been flashing for a while I cut the light and the cell phone stayed on Emergency mode and I turned off the rage and save it a few days ago I connected it to the PC and in the Device Manager it appeared as Unknown Device and it did not turn on neither in Emergency Mode nor in Recovery or in anything, inquiring for this same forum. I realized that it was a Hard Brick and I want to know how to do it with this phone model. I would appreciate all the help possible. On the PC I have Win 10 Pro and I have the latest LG drivers and the Unknown Device still appears in the Device Manager.
I have tried all the possible combinations, I charged the battery completely with a universal charger, I have left the phone connected to the PC more than 5 hours, I have kept the power button on the phone for around 15 minutes and none of them has worked for me. Please help me.
Excuse my English, I'm from Venezuela and well
Hello, i think my phone is completely dead. Here's what happened : i wanted to go back to a stock ROM so i used MiFlash, but it gave me an error really early after a couple seconds (modem flash error i think) and now it doesn't respond. When i connect it to my PC nothing happens (nothing in device manager). The only sign of "life" is that when the battery is low (i think that's the case), the LED starts flashing RED until the phone runs out of juice. Any ideas? I already tried charging the phone all the way up and then discharging it completely(those are the only things that seem to work as they should) but the phone seems completely dead. I had a similar thing happen to me before on my older Xiaomi phone but that time my PC at least managed to detect it in device manager as qdloader 9008 (EDL mode) but that just doesn't seem to work now. Would shorting the test points work to make it go into EDL mode or is it a lost call? The bootloader was unlocked before flashing and i chose the option in MiFlash that doesn't lock it again. Thanks for anything. EDIT: Phone sent to a repair centre.
I have some previous threads on my Redmi 7A dead... but no one responded, some did but said I can't fix it, buy a new phone. I am not in a financial condition to buy a new phone. All I can do is fix this phone and continue using it till I get a new phone. But since 3 weeks I am not able to use my Redmi 7A. I was hopeless that this phone could be repaired or could be used again but I went through a few videos on YouTube and saw a ray of hope but still I was helpless I tried booting it into EDL mode using the test point method but nothing worked out. Please I NEED HELP to fix this phone. I have a brief description below of the timeline about how it
crashed, how it was in the service center, what happened after it.
Alright so,
At March 13, It was on AOD (I know it is not supported keep reading), running nusantra os latest version for (Mi-439 aka Redmi 7A, 8) which was last updated on Dec 4, 2022. So when It was on AOD I tried to unlock the phone and it froze. So I rebooted it abnormally. After it was booting it stuck on the Redmi logo but it wasn't going ahead, not showing the boot animation. So I tried to boot it in recovery mode, when it was booting in recovery mode the phone was just shutting down and trying to reboot itself again but it couldn't. So I tried to wipe everything using fastboot commands and the command which I used was -w. So after that instead of waiting at the redmi logo it was stuck in a bootloop, in fact booting in the bootloader (fastboot mode). So after that I lost hope and gave it to the nearby service center. Please note that the phone was turning on before giving it to the service center. After like one day I went there to check if it was done, they say that it's a hardware problem, they are not able to fix it, When I came home the phone didn't boot neither in the fastboot mode nor It was turning on. So I thought it's not charged so I charged it for 1.5 hours but still there was no sign of life. I asked them about the phone not turning on they told me that it's a hardware issue and hung up the phone, said I am in a hurry I will call you later. Till this day I received no call. So Now I am posting this because I see some hope of EDL mode. I even tried to boot it in the EDL mode but still it was neither booting in the EDL mode nor my computer is detecting my phone (I have all the drivers installed). Please help ASAP.
Gibbron1 said:
there was no sign of life
Click to expand...
Click to collapse
1. does the led light up when you charge it?
2. what does you pc device manager show when you plug it in? (do you hear the windows sound?)
try every button combination that is possible. i mean two buttons at the same time, three buttons, all buttons... and for about even up to 1 minute (because this brought my 7A back from just led light when charging to pc detected a usb device)
i can't reproduce your brick but i managed to debrick via edl mode once on a "complete dead" (only led lights up when charging) so i think you can do that too.
also as long as you work with the EDL Tool, deactivate your Firewall (and don't forget to activate it again) just so be sure.
3. are you trying to enter edl mode via adb terminal? i would say you have to open the back cover and enter edl mode via hardware bridge from edl point to ground.
and as far as i can remember you have to be really quick between "starting" (booting) edl mode on the phone and make the phone "accept" edl mode. i think i first made the hardware bridge and then pluged the usb in.
i will dig deeper again in the next few days so i can give you better info's
mYXiao said:
1. does the led light up when you charge it?
2. what does you pc device manager show when you plug it in? (do you hear the windows sound?)
try every button combination that is possible. i mean two buttons at the same time, three buttons, all buttons... and for about even up to 1 minute (because this brought my 7A back from just led light when charging to pc detected a usb device)
i can't reproduce your brick but i managed to debrick via edl mode once on a "complete dead" (only led lights up when charging) so i think you can do that too.
also as long as you work with the EDL Tool, deactivate your Firewall (and don't forget to activate it again) just so be sure.
3. are you trying to enter edl mode via adb terminal? i would say you have to open the back cover and enter edl mode via hardware bridge from edl point to ground.
and as far as i can remember you have to be really quick between "starting" (booting) edl mode on the phone and make the phone "accept" edl mode. i think i first made the hardware bridge and then pluged the usb in.
i will dig deeper again in the next few days so i can give you better info's
Click to expand...
Click to collapse
I bought another phone, but thanks for the reply and help you gave me. My new Phone is Mi A1.