After installing all the drivers and the flash tool the most important step is to boot the phone into edl mode or 9008 port which is very tricky step
STEPS:-
1. Power off the phone completely.
2. Press the volume up button for almost 15 sec without leaving press the power button for .5 sec (don't leave the volume button).
3. Again press the power button and hold it and immediately put the cable into the pc .
(note:- these time two buttons are pressed power button and the volume up button which was pressed in step two)
4. Leave both buttons when you receive the connection sound on the pc and check in the device manager now you connected to
the 9008 port instead of the 900E port.
(note:- step 4 can be symbolizes as you will get zuk logo flashed for a split of second after connecting the cable to the pc and
after that whole screen will be black and then after leave all the buttons and flash the phone with qpst)
refference:-http://forums.easy-firmware.com/showthread.php?97902-Lenovo-ZUK-Z2-Plus-EDL-Mode-And-Flashing-Process
how to turn off the phone completely while this phone hard bricked? im a noob, sorry
Aldhryy said:
how to turn off the phone completely while this phone hard bricked? im a noob, sorry
Click to expand...
Click to collapse
Press the power button for long time about 15-20sec until notification led gose off
Additional, some bricked devices may stuck in 900E mode, just keep on pressing in power botton and your device will reboot(screen may still be black, u must stare at the display of mode of your QFIL tool) .After rebooting some times(8∽9 times normally), your device will force boot into 9008 mode (you have to release the botton in a very short time or retry above lol) .
This method isnt from me and just tested on my phone succeefull .Hope helpful to someone.
Zuk Z2 Pro Stuck in EDL HS-USB 9008 Port and automatically connecting and disconnect
Hi,
My Zuk Z2 Pro is stuck in EDL 9008 Port. Phone is totally bricked and no sound, no light, no vibration. When i connect with the computer, phone is connecting on HS USB 9008 port and get disconnected after 20-22 seconds and again automatically connected with in half second time.
I am facing this issue after flashing a ZUI 1.9 by using a QPAST/QFIL application. I think i have made stupid mistake by flashing a phone with "ERASE ALL BEFORE DOWNLOAD" option.
I have tried every scenario to get stable this 9008 port but no luck. Since last 5 days i am studying forums and applying every kind of solution but same result.
I am writing this post with high expectations and hope someone will take notice and help me to get rid of this problem.
I can pay through paypal if someone wants to provide professional services to resolve this matter
I will appreciate if someone have any idea and can help me. Thanks
Farazk said:
Hi,
My Zuk Z2 Pro is stuck in EDL 9008 Port. Phone is totally bricked and no sound, no light, no vibration. When i connect with the computer, phone is connecting on HS USB 9008 port and get disconnected after 20-22 seconds and again automatically connected with in half second time.
I am facing this issue after flashing a ZUI 1.9 by using a QPAST/QFIL application. I think i have made stupid mistake by flashing a phone with "ERASE ALL BEFORE DOWNLOAD" option.
I have tried every scenario to get stable this 9008 port but no luck. Since last 5 days i am studying forums and applying every kind of solution but same result.
I am writing this post with high expectations and hope someone will take notice and help me to get rid of this problem.
I can pay through paypal if someone wants to provide professional services to resolve this matter
I will appreciate if someone have any idea and can help me. Thanks
Click to expand...
Click to collapse
1. Try uninstalling all the drivers you installed.
2.switch of your phone compeletly.
3.follow the link.
https://www.google.co.in/amp/s/foru...ecover-hard-bricked-zuk-z2-plus-t3576007/amp/
Solved: Zuk Z2 Pro Stuck in EDL 9008 mode and port auto connecting/disconnecting
[email protected] said:
1. Try uninstalling all the drivers you installed.
2.switch of your phone compeletly.
3.follow the link.
https://www.google.co.in/amp/s/foru...ecover-hard-bricked-zuk-z2-plus-t3576007/amp/
Click to expand...
Click to collapse
The Problem is resolved. I charged my battery 7-8 Hours and flashing done at first attempt. My phone was stuck in EDL mode and Port 9008 was continues connecting /disconnecting and i was not able to complete a flashing process. Flashing by using Qfil really sucked a battery. So if someone face such kind of issue, please charge your battery for 7-8 Hours and then try flashing.
Aldhryy said:
how to turn off the phone completely while this phone hard bricked? im a noob, sorry
Click to expand...
Click to collapse
The phone turns off completely when there's nothing on-screen (no error), notification, and no vibration
Related
Hello!
As title says i bricked my Axon :crying:
I followed http://forum.xda-developers.com/showpost.php?p=68738854&postcount=100 (and the german one that linked to this one) but couldnt do the fastboot unlock.
So i couldnt finish this and my phone required a pin number to start android: bootet and started up but wanted a pin code to start/enter system.
Wasnt able to fix that with googling for answers so i went back to edl mode and rewrote my backup boot/recovery images with axon7backup.
Had no errors with that but it wont start now:
After the ZTE Logo the display goes black but it connects as "handset diagnostic interface (DFU) (ComX)" to my computer.
I fiddled around with driver installing etc and forced the HS-USB QDLoader 9008 on it but no luck, axon7backup/root can not connect.
When i did the actual flashing yesterday it never connected with the hold both vol-keys and connect usb way either, always had to reboot into edl via adb.
I cant boot anything else (no twrp/recovery) it just goes to the diagnostic interface mode.
Thanks in advance
you can try to get into adb mode with this:
- power off your device
- hold the vol down key while plugin in the usb-c cable (connected to your pc)
- keep holding
- you should get a white box with FTM factory test mode
- you are free to use adb again - so you can get into edl mode as well....
for pin part that'S normal while unlocking your device encryption gets deleted and you have to abort and factory reset your device in twrp....
Starvirus said:
you can try to get into adb mode with this:
- power off your device
- hold the vol down key while plugin in the usb-c cable (connected to your pc)
- keep holding
- you should get a white box with FTM factory test mode
- you are free to use adb again - so you can get into edl mode as well....
for pin part that'S normal while unlocking your device encryption gets deleted and you have to abort and factory reset your device in twrp....
Click to expand...
Click to collapse
Thanks. I tried it but it wont go to FTM. Only goes to diagnostic com port.
It seems i cant even turn it off. The little red light on the front is on the whole time .
sadly the disadvantage of a built in battery, so you have to wait till the battery is empty and try my instructions then....if it's not realy off it won't work, the mode you are currently in you usually only reach if you switch it on while holding both volume buttons, the edl mode is sadly not reachable with a key combination directly on G models.
adb don't show your device?
Starvirus said:
sadly the disadvantage of a built in battery, so you have to wait till the battery is empty and try my instructions then....if it's not realy off it won't work, the mode you are currently in you usually only reach if you switch it on while holding both volume buttons, the edl mode is sadly not reachable with a key combination directly on G models.
Click to expand...
Click to collapse
Oh ok. I expected ftm to work from vol-down and power-button till restart.
@adb: sadly no connection possible since it goes straight to Comport Connection.
Edit:
Couldnt make that work. It was off and i connected the usb. So it showed me the loading battery picture where i cant do anything. held the vol-down the whole time. But as soon as it had some battery it went straight to comport-connection again
im sorry to say, but ur device is bricked to a degree where you would need ZTEs Flashtool to fix it. Unfortunately we dont have that tool, so you might have to send it in
i have the same exact problem :'(
Have u been able to fix it?? I'm in a situation that i cant even send it to ZTE to fix it :'(
nsabir said:
i have the same exact problem :'(
Have u been able to fix it?? I'm in a situation that i cant even send it to ZTE to fix it :'(
Click to expand...
Click to collapse
Hi,
couldnt fix it myself so i had to send it in.
Unless some tool/rom was released in the last few months to fix it yourself i would guess your device is bricked.
Hi I have almost the same problem, I tried to unlock bootloader and now I don't have the recovery, I can boot and use my mobile but I can't restore it or update it because I don't have the recovery
I try whit axon7tool to restore the recovery but I got a error.
MaxRink said:
im sorry to say, but ur device is bricked to a degree where you would need ZTEs Flashtool to fix it. Unfortunately we dont have that tool, so you might have to send it in
Click to expand...
Click to collapse
Hi, do you have any idea, if there will be such a flashtool to work with DFU mode? I'm thinking that there are a lot of guys have bricked their devices (including me).
((
Well, today, I flash a wrong firmware on my RN3 pro RR 5.8.3, unlock unofficially and get brick. No fastboot, No recovery, long press power button only brought splash screen for a second then screen goes black again. When stick to PC only red led blinking, on Device manager show Qualcomm HS-USB Diagnostics 900E so no Miflash.
Okay after a whole morning, I found this method here http://en.miui.com/forum.php?mod=viewthread&tid=266598&highlight=900e.. I tried method 3 from that thread because the other are just unreadable. So here is the step:
1. Plug the phone to PC - Red led blinking
2. Hold both 3 button: Volume up, Volume Down, Power button for around 10s. Phone vibrate and show the Linux Penguin Icon (Qualcom mode)
3. Check in Device manager/Port , it show other (unfortunately not the 9008 as in the thread). I check with Miflash Phone is recognize but i Cant flash any thing
4. SO i tried using this method here (step 4 ) https://forum.xda-developers.com/showpost.php?p=69613342&postcount=3 and get into EDL mode with 9008 port. Voila!
Optional
5. Then I flash this TWRP and unlock officially from here https://forum.xda-developers.com/redmi-note-3/how-to/unlock-unofficially-install-zcx-twrp-t3586778 and the beast is up again ! :highfive:
So i post this here to help anyone stuck in EDL mode and dont have a DFC or dont want to use test point method.
hope this help .
Thanks for sharing.
I already have deep flash cable (btw I made it myself, it is easy) and I have used it some times... But it is good if u don't have the cable!!
Regards!
Thanks a lot for this small post, it saved me from throwing this phone out of the window.
I could update MIUI using fastboot EDL, weirdely enough you cannot update official MIUI without unlocking the bootloader... WTF xiaomi
Saved my ass man thank you i got a real headache from all the failed attempts but u did the job.
my Redmi 4 no response. wat I do now.
when I connect usb cable to phone to pc it's show direct edl mode or Qualcomm Snapdragon 9008 is connected in port .
so what happened it?
wat I do now pls help me.
I know how QHSUSB_BULK is used because I had a brick but what happened with my cell phone is that when I flashed it I stopped recognizing it. uninstall everything to start again and when I connected my cellphone, QHSUSB_BULK did not appear anymore. I think I install a rom that is not.
When QHSUSB_BULK did not appear, my computer recognized as UNKNOW DEVICE. but when installing the drivers I only recognized the Qualcomm HSUSB QDLoader 9008. because the android is still in UNKNOWN DEVICE. USB \ UNKNOW USB \ VID_0000 & PID_0000.
There is no recovery, no FTM, no load, no turn on.
I can not switch to EDL mode
Start Sending Programmer
Download Fail: Unable to download Flash Programmer using Sahara Protocol
Download Fail: Sahara FailSahara Fail
Finish Download
I can not flash again,
Would the emmc be damaged or did it lose its format?
Excuse my english, I'm using google.
Sorry about that, what's your Compilation number?
nvizync said:
Sorry about that, what's your Compilation number?
Click to expand...
Click to collapse
V1.0.0B13 BBversion Z835H01
isaac ballesteros said:
V1.0.0B13 BBversion Z835H01
Click to expand...
Click to collapse
Ok, you need to charge your device, at least 70%, even if no logo, sign of life, or whatsoever is need to be showed, then remove the battery, wait at least 5 or 10 minutes, put the battery back and inmediatly connect the usb cable holding vol down, so that way, you gonna force your phone to boot into FTM mode, don't be scared, that happened to me also, trying to flash a V1.0.0B13 with V2.0.0B10, and with this way i successfully make my phone come back to life again.
nvizync said:
Ok, you need to charge your device, at least 70%, even if no logo, sign of life, or whatsoever is need to be showed, then remove the battery, wait at least 5 or 10 minutes, put the battery back and inmediatly connect the usb cable holding vol down, so that way, you gonna force your phone to boot into FTM mode, don't be scared, that happened to me also, trying to flash a V1.0.0B13 with V2.0.0B10, and with this way i successfully make my phone come back to life again.
Click to expand...
Click to collapse
No charge, no FMT but i will try it.
isaac ballesteros said:
No charge, no FMT but i will try it.
Click to expand...
Click to collapse
I know, it can be scary but try, even if it's all black
i have blank screen too how to fix?
I don't know what has happened... I took the phone off my charger at about 80%, was playing on it for a little bit and then restarted the phone.... the next moment I look at it, it is just a black screen. It is completely dead, pushing or holding power button does nothing (held for minutes multiple times), holding volume buttons & power button does nothing, plugging in to charger does nothing. It seems to be completely dead.
I have no idea why, it was working fine until I selected restart and was dead a few minutes later. Completely normal usage prior to that.
Anyone have any suggestions for what I can do to get this phone turned back on at all??
Nubia Z17 NX563J
Kind of a pain that these are completely sealed units...
I've just seen some posts about the Nubia Emergency Tool. If I plug my phone into the PC it does show up as "Qualcomm HS-USB QDLoader 9008" device so it looks like the emergency tool might work with it.
But does that mean it will flash my phone and I will lose all data on it?
There was nothing wrong with it just before, is there no other way to recover the data?
bunta126 said:
I've just seen some posts about the Nubia Emergency Tool. If I plug my phone into the PC it does show up as "Qualcomm HS-USB QDLoader 9008" device so it looks like the emergency tool might work with it.
But does that mean it will flash my phone and I will lose all data on it?
There was nothing wrong with it just before, is there no other way to recover the data?
Click to expand...
Click to collapse
How long have you used your phone? Better to replace the battery as one of my phones behaves the same way. Just replace the battery and that's it.
Tims Fong said:
How long have you used your phone? Better to replace the battery as one of my phones behaves the same way. Just replace the battery and that's it.
Click to expand...
Click to collapse
But the battery is not replaceable...?
bunta126 said:
But the battery is not replaceable...?
Click to expand...
Click to collapse
[NX563J][Project Treble][Android 10-11-12-13][GSI][AB]
Whats about magisk it Boot no more gsi after Flash magisk use this:https://github.com/ExpressLuke/phh-magisk-builder/releases/download/08-12-2020/magisk-v21.1-phh.zip
forum.xda-developers.com
bunta126 said:
But the battery is not replaceable...?
Click to expand...
Click to collapse
you need special usb cable i got same problem long time before
for edl mode
Update: I managed to get the bootloader and recovery working using the Nubia Emergency Tool. The system would not boot and even a dirty flash of the same ROM I was using would not make it boot. I could reinstall the ROM however and the phone is now working fine again.
So, I rebuilt my phone with a completely different ROM on Android 13, and today the same thing has happened: I chose to restart my phone and it has gone black and won't turn back on again.
It has been running perfectly fine on the new ROM until today, why would this same problem reoccur? I suppose battery is likeliest issue... although maybe there is something I'm doing to break the system?
I have some previous threads on my Redmi 7A dead... but no one responded, some did but said I can't fix it, buy a new phone. I am not in a financial condition to buy a new phone. All I can do is fix this phone and continue using it till I get a new phone. But since 3 weeks I am not able to use my Redmi 7A. I was hopeless that this phone could be repaired or could be used again but I went through a few videos on YouTube and saw a ray of hope but still I was helpless I tried booting it into EDL mode using the test point method but nothing worked out. Please I NEED HELP to fix this phone. I have a brief description below of the timeline about how it
crashed, how it was in the service center, what happened after it.
Alright so,
At March 13, It was on AOD (I know it is not supported keep reading), running nusantra os latest version for (Mi-439 aka Redmi 7A, 8) which was last updated on Dec 4, 2022. So when It was on AOD I tried to unlock the phone and it froze. So I rebooted it abnormally. After it was booting it stuck on the Redmi logo but it wasn't going ahead, not showing the boot animation. So I tried to boot it in recovery mode, when it was booting in recovery mode the phone was just shutting down and trying to reboot itself again but it couldn't. So I tried to wipe everything using fastboot commands and the command which I used was -w. So after that instead of waiting at the redmi logo it was stuck in a bootloop, in fact booting in the bootloader (fastboot mode). So after that I lost hope and gave it to the nearby service center. Please note that the phone was turning on before giving it to the service center. After like one day I went there to check if it was done, they say that it's a hardware problem, they are not able to fix it, When I came home the phone didn't boot neither in the fastboot mode nor It was turning on. So I thought it's not charged so I charged it for 1.5 hours but still there was no sign of life. I asked them about the phone not turning on they told me that it's a hardware issue and hung up the phone, said I am in a hurry I will call you later. Till this day I received no call. So Now I am posting this because I see some hope of EDL mode. I even tried to boot it in the EDL mode but still it was neither booting in the EDL mode nor my computer is detecting my phone (I have all the drivers installed). Please help ASAP.
Gibbron1 said:
there was no sign of life
Click to expand...
Click to collapse
1. does the led light up when you charge it?
2. what does you pc device manager show when you plug it in? (do you hear the windows sound?)
try every button combination that is possible. i mean two buttons at the same time, three buttons, all buttons... and for about even up to 1 minute (because this brought my 7A back from just led light when charging to pc detected a usb device)
i can't reproduce your brick but i managed to debrick via edl mode once on a "complete dead" (only led lights up when charging) so i think you can do that too.
also as long as you work with the EDL Tool, deactivate your Firewall (and don't forget to activate it again) just so be sure.
3. are you trying to enter edl mode via adb terminal? i would say you have to open the back cover and enter edl mode via hardware bridge from edl point to ground.
and as far as i can remember you have to be really quick between "starting" (booting) edl mode on the phone and make the phone "accept" edl mode. i think i first made the hardware bridge and then pluged the usb in.
i will dig deeper again in the next few days so i can give you better info's
mYXiao said:
1. does the led light up when you charge it?
2. what does you pc device manager show when you plug it in? (do you hear the windows sound?)
try every button combination that is possible. i mean two buttons at the same time, three buttons, all buttons... and for about even up to 1 minute (because this brought my 7A back from just led light when charging to pc detected a usb device)
i can't reproduce your brick but i managed to debrick via edl mode once on a "complete dead" (only led lights up when charging) so i think you can do that too.
also as long as you work with the EDL Tool, deactivate your Firewall (and don't forget to activate it again) just so be sure.
3. are you trying to enter edl mode via adb terminal? i would say you have to open the back cover and enter edl mode via hardware bridge from edl point to ground.
and as far as i can remember you have to be really quick between "starting" (booting) edl mode on the phone and make the phone "accept" edl mode. i think i first made the hardware bridge and then pluged the usb in.
i will dig deeper again in the next few days so i can give you better info's
Click to expand...
Click to collapse
I bought another phone, but thanks for the reply and help you gave me. My new Phone is Mi A1.