Database Users

D802 v30a ERROR: Boot certification verify - Secure boot error

Yesterday I flashed (CSE flash) v30a KDZ to recover my GPS which as having problems getting locks and it all went well, it seemed the GPS got back working.
Later I used the DP Root to root it and it went ok.
After using the DP REC (if required for evaluation, please inform), my phone rebooted and it showed me the following message:
ERROR : boot certification verify
[1040] ------------------------------------------
[1090]
[1140] Secure booting Error!
[1200] Cause : boot certification verify
[1250]
[1300] ------------------------------------------
Click to expand...
Click to collapse
Then goes to this:
------------------------------------------
Critical Error!
------------------------------------------
Demigod Crash Handler : Critical Error!
Press key to choose Dload Mode or Reboot.
1) Volume Up : Dload Mode
2) Volume Down : Reboot.
If you choose Dload Mode,
Please do following action.
1) Dload Mode. Please connect USB.
2) Get the ram dump image using QPST Configuration.
------------------------------------------
Board Info
rev. : 1.1 speed,pvs : 1,2 serial : XXXXXXXXXX
------------------------------------------
Click to expand...
Click to collapse
Pressing the power button for more than 13s I can shut it down so that I can try the Volume Up + connect USB, but then it just powers the phone on and starts the above stated.
By pressing the Volume down + Power and pressing again after the LG Logo shows up, I can go to the reset screen but at the finish it doesn't show the factory reset or TWRP, just starts the sequence of screens above.
By pressing the Volume Up on the Demigod Crash screen, it show the following message:
Volume Up is pressed : Jump to Dload Mode.
Click to expand...
Click to collapse
and stays that way, but then the computer recognizes the "LGE AndroidNet USB Modem" and "LGE AndroidNet Serial Port", no more LG stuff there, and the LG Flash Tool doesn't go past 4%.
On Ubuntu it recognizes the same devices, but doesn't get the partitions
Does anyone know any way so that I can get out of this?

Hi @darknessmessiah,
Any luck with your issue? I've received a strikingly similar result after attempting to flash the stock lollipop to my LG G2 801 from the T-mobile forum.

jjmontem said:
Hi @darknessmessiah,
Any luck with your issue? I've received a strikingly similar result after attempting to flash the stock lollipop to my LG G2 801 from the T-mobile forum.
Click to expand...
Click to collapse
Hi there! Yes, I got to get it back... But it was this hard
Anyway there goes some tips:
After you remove the battery plug, you only need to put it back after everything is done.
You have to keep trying the short circuit until you get a new hardware called "Qualcomm hs-diagnostics 9006" and you computer recognizes a lot of disk partitions. The normal device my computer recognized was "Qualcomm HS-USB QDLoader 9008" and no tip out there worked.
When the computer recognizes the wrong device, remove the USB, plug it back and try again. One time it recognized one whole 32GB partition, but thankfully I didn't try anything besides removing the USB and try again.
After everything, I got Download Mode back and, after some tries (I've got some errors), got the flashtool to flash the ROM back.

jjmontem said:
Hi @darknessmessiah,
Any luck with your issue? I've received a strikingly similar result after attempting to flash the stock lollipop to my LG G2 801 from the T-mobile forum.
Click to expand...
Click to collapse
infect you need to fix the download mod
i can fix plz contact me https://www.facebook.com/faheem.anjum2

Wow, that's miserably complicated. And to show you my naivite, I wasn't aware that one could enter download mode by plugging in the phone to a computer with a USB cord, and holding the volume up button as it started up. My phone successfully entered download mode and I was able to use LG Flash Tool 2014 to return my phone to Stock 4.2.2 using this thread and a KDZ I had long ago stored.
Thanks for the help though!
darknessmessiah said:
Hi there! Yes, I got to get it back... But it was this hard
Anyway there goes some tips:
After you remove the battery plug, you only need to put it back after everything is done.
You have to keep trying the short circuit until you get a new hardware called "Qualcomm hs-diagnostics 9006" and you computer recognizes a lot of disk partitions. The normal device my computer recognized was "Qualcomm HS-USB QDLoader 9008" and no tip out there worked.
When the computer recognizes the wrong device, remove the USB, plug it back and try again. One time it recognized one whole 32GB partition, but thankfully I didn't try anything besides removing the USB and try again.
After everything, I got Download Mode back and, after some tries (I've got some errors), got the flashtool to flash the ROM back.
Click to expand...
Click to collapse

jjmontem said:
Wow, that's miserably complicated. And to show you my naivite, I wasn't aware that one could enter download mode by plugging in the phone to a computer with a USB cord, and holding the volume up button as it started up. My phone successfully entered download mode and I was able to use LG Flash Tool 2014 to return my phone to Stock 4.2.2 using this thread and a KDZ I had long ago stored.
Thanks for the help though!
Click to expand...
Click to collapse
Well... You were in a better situation than myself... holding the volume up and plugging the USB didn't work for me either... It was heavily messed up!

hi do you find solution
---------- Post added at 09:53 PM ---------- Previous post was at 09:48 PM ----------
i have same probleme with my lg g F320L can anyone help ?

Heavy Hard Brick Zuk Z1 international Version

HI everybody, I have a very big problem with my zuk. Trying to solve a problem about network, I thought to come back to stock via fastboot. But given that I was tired doing so many tries, I wrongly flash a zip file via fastboot instead of use adb, so the phone didn't turn on anymore. I must say first of all that it isn't my first phone, so I'm not a newbie. The real problem is: When I plug Zuk into my Pc( Windows 10) it isn't recognized as qhsusb_bulk ( It could be easy to solve the problem) but as "unknown usb device (Device Descriptor Request Failed)". I try to plug the phone pressing every button like Vol+ and power, Vol- and power but nothing to do. I' m already in Test Mode on Windows 10 and I deleted every Zuk or Qualcomm Drivers. Anyone can help me?
Thank you
Ps: Even If the screen is always off, Is there a way to boot into fastboot mode with hardware keys?

Xluk3 said:
HI everybody, I have a very big problem with my zuk. Trying to solve a problem about network, I thought to come back to stock via fastboot. But given that I was tired doing so many tries, I wrongly flash a zip file via fastboot instead of use adb, so the phone didn't turn on anymore. I must say first of all that it isn't my first phone, so I'm not a newbie. The real problem is: When I plug Zuk into my Pc( Windows 10) it isn't recognized as qhsusb_bulk ( It could be easy to solve the problem) but as "unknown usb device (Device Descriptor Request Failed)". I try to plug the phone pressing every button like Vol+ and power, Vol- and power but nothing to do. I' m already in Test Mode on Windows 10 and I deleted every Zuk or Qualcomm Drivers. Anyone can help me?
Thank you
Ps: Even If the screen is always off, Is there a way to boot into fastboot mode with hardware keys?
Click to expand...
Click to collapse
Not that I know,do you have the stock recovery or twrp?

I have the exact problem with my new zuk z1. Any idea is appreciated. The nice phone seems lost now.

Seems like you'll have to restore your zuk to the zui version again. Do you have qrst and zui version downloaded??

The service port never pops up
I do have the qpst and the zui rom. The main obstacle is that qualcomm service port never pop up.

Setup.zuk said:
I do have the qpst and the zui rom. The main obstacle is that qualcomm service port never pop up.
Click to expand...
Click to collapse
try this:
start QFIL from the QPST folder
Click browse on the programmer path row and select prog_emmc_firehose_8974.mbn from the directory where you unzipped the QPST ZUI ROM
and then click browse on the search path row and select the xml file + the other patch file which comes after it.
When thats done, make sure phone is off and then hold vol+ while you are inserting usb cable into phone and QFIL should then detect phone,
you may need to select port in the QFIL program and be quick with it, took me a few tries before I got it right so just take out the cable
and turn off and try again if you fail to make them connect.
Not only you need to select comport, you also need to press the download button aswell as soon as possible or else phone will continue booting as normal.
If everything went well then you should have ZUI loaded onto your phone and you are met with Chinese language as default.
On the first screen you are met with, just press the button in the bottom (on screen), then press cogwheel (which is the settings),
scroll down to yet another cogwheel in here which should be below a lock icon, then press second option in here and then the top option
to change language to english incase you cant make out the chinese and you should be good to go

Nikosstamatiou said:
try this:
start QFIL from the QPST folder
Click browse on the programmer path row and select prog_emmc_firehose_8974.mbn from the directory where you unzipped the QPST ZUI ROM
and then click browse on the search path row and select the xml file + the other patch file which comes after it.
When thats done, make sure phone is off and then hold vol+ while you are inserting usb cable into phone and QFIL should then detect phone,
you may need to select port in the QFIL program and be quick with it, took me a few tries before I got it right so just take out the cable
and turn off and try again if you fail to make them connect.
Not only you need to select comport, you also need to press the download button aswell as soon as possible or else phone will continue booting as normal.
If everything went well then you should have ZUI loaded onto your phone and you are met with Chinese language as default.
On the first screen you are met with, just press the button in the bottom (on screen), then press cogwheel (which is the settings),
scroll down to yet another cogwheel in here which should be below a lock icon, then press second option in here and then the top option
to change language to english incase you cant make out the chinese and you should be good to go
Click to expand...
Click to collapse
So i am having the same problem. The phone is not being recognized by the software. That is the whole problem. Any ideas?

Tarsa said:
So i am having the same problem. The phone is not being recognized by the software. That is the whole problem. Any ideas?
Click to expand...
Click to collapse
Actually, I think the problem is, that it will not reach the fastboot mode, due to the non-stop process of system-updating and boot-loop. I can observe for a very short time the message 'systemupdate will be installed' and then the screen becomes black again. This procedure is repeating every time. I will wait till the battery is empty and see, whether the boot with Volume-+--USB-cable will work.

mikarbach said:
Actually, I think the problem is, that it will not reach the fastboot mode, due to the non-stop process of system-updating and boot-loop. I can observe for a very short time the message 'systemupdate will be installed' and then the screen becomes black again. This procedure is repeating every time. I will wait till the battery is empty and see, whether the boot with Volume-+--USB-cable will work.
Click to expand...
Click to collapse
PLease do update me if you manage to fix it. This is getting very frustrating

I have the same problem, caused after a cyanogenmod update... Did someone fix this??

Another hard bricked Z1 here.
QFIL recognizes the phone (as Qualcomm 9008 etc.). So I am able to click Download, but after a few seconds, it fails with these errors:
Code:
[...]
Sending NOP
NOP: Fail Code: 9
Unable to send FireHose NOP, Device is not in Firehose mode !
Download Fail:System.Exception: Failed to send Firehose NOP to the phone.
in QC.QMSLPhone.Phone.QPHONEMS_FireHoseNOP()
in QC.SwDownloadDLL.SwDownload.FireHoseDownloadImage(Boolean bResetPhone, List`1 rawprogramFilesList, List`1 patchFilesList, Single& fImageSizeInMB, Single& fThroughput)
Download Fail:FireHose Fail FireHose Fail
Finish Download
I've tried many many times, and many different things. Still no luck .
I'd appreciate if anyone could input some new ideas of other stuff to try. Thanks

CarlosAir said:
Another hard bricked Z1 here.
QFIL recognizes the phone (as Qualcomm 9008 etc.). So I am able to click Download, but after a few seconds, it fails with these errors:
Code:
[...]
Sending NOP
NOP: Fail Code: 9
Unable to send FireHose NOP, Device is not in Firehose mode !
Download Fail:System.Exception: Failed to send Firehose NOP to the phone.
in QC.QMSLPhone.Phone.QPHONEMS_FireHoseNOP()
in QC.SwDownloadDLL.SwDownload.FireHoseDownloadImage(Boolean bResetPhone, List`1 rawprogramFilesList, List`1 patchFilesList, Single& fImageSizeInMB, Single& fThroughput)
Download Fail:FireHose Fail FireHose Fail
Finish Download
If tried many many times, and many different things. Still no luck .
I'd appreciate if anyone could input some new ideas of other stuff to try. Thanks
Click to expand...
Click to collapse
No idea, my device is actually dead.

mikarbach said:
No idea, my device is actually dead.
Click to expand...
Click to collapse
Aw .
I don't want to lose hope, but everything I've tried so far has failed. :| , and I don't know what else to try.

CarlosAir said:
Aw .
I don't want to lose hope, but everything I've tried so far has failed. :| , and I don't know what else to try.
Click to expand...
Click to collapse
Try another cable, another USB slot, another pc/laptop

mikarbach said:
No idea, my device is actually dead.
Click to expand...
Click to collapse
try to flash cos 12.1 with qfil.
its there somwhere on 4pda forum(search there).
Sent from my Z1 using XDA-Developers mobile app

So guys if I try to flash unofficial CM 13 do I risk bricking the device for good???

t.h.i said:
try to flash cos 12.1 with qfil.
its there somwhere on 4pda forum(search there).
Sent from my Z1 using XDA-Developers mobile app
Click to expand...
Click to collapse
Of course I have tried this, with two different computers and two different USB cable, both actually working on my N5X. But the point is, that I do not reach the point, that qfil recognizes the phone. Also not with the trick of starting with power-button/USB-cable. It constantly tries to reboot and with adb I get a message 'not authorized' .
---------- Post added at 11:17 AM ---------- Previous post was at 11:05 AM ----------
carlese said:
So guys if I try to flash unofficial CM 13 do I risk bricking the device for good???
Click to expand...
Click to collapse
I think in my case the after the first successful CM13-snapshot-installation was two fold:
1. I have not enabled USB-debugging and do not have had connected it to my computer after the first CM13-installation.
2. Due to some unknown reason the automatically update via CM itself has boot looped.
The second point is not a real problem, I think. I have had a bootloop many times before with other phones, as well as with the Zuk, but I was always able to resolve the problem with adb. I think the first point was the problem, so adb wasn't possible, due to authorization problems. The reason why qfil does not work, I really do not know exactly, but qfil in fact was not able to recognize the phone.

I have the same problem. Totally bricked.
No charge, no PC recognise, nothing.
I tried with QFIL but the PC does not recognise the port.
I don't know what else I can do. Any ideas?
Thanks!

alexisdance said:
I have the same problem. Totally bricked.
No charge, no PC recognise, nothing.
I tried with QFIL but the PC does not recognise the port.
I don't know what else I can do. Any ideas?
Thanks!
Click to expand...
Click to collapse
Sry, no I do not have

Hello!
I have dealt with this sort of problem before and have successfully un-bricked my friend's device. I will be posting a guide to solve this problem soon.
Hang-on!

Bricked A2017G B03 - help please

Hello!
As title says i bricked my Axon :crying:
I followed http://forum.xda-developers.com/showpost.php?p=68738854&postcount=100 (and the german one that linked to this one) but couldnt do the fastboot unlock.
So i couldnt finish this and my phone required a pin number to start android: bootet and started up but wanted a pin code to start/enter system.
Wasnt able to fix that with googling for answers so i went back to edl mode and rewrote my backup boot/recovery images with axon7backup.
Had no errors with that but it wont start now:
After the ZTE Logo the display goes black but it connects as "handset diagnostic interface (DFU) (ComX)" to my computer.
I fiddled around with driver installing etc and forced the HS-USB QDLoader 9008 on it but no luck, axon7backup/root can not connect.
When i did the actual flashing yesterday it never connected with the hold both vol-keys and connect usb way either, always had to reboot into edl via adb.
I cant boot anything else (no twrp/recovery) it just goes to the diagnostic interface mode.
Thanks in advance

you can try to get into adb mode with this:
- power off your device
- hold the vol down key while plugin in the usb-c cable (connected to your pc)
- keep holding
- you should get a white box with FTM factory test mode
- you are free to use adb again - so you can get into edl mode as well....
for pin part that'S normal while unlocking your device encryption gets deleted and you have to abort and factory reset your device in twrp....

Starvirus said:
you can try to get into adb mode with this:
- power off your device
- hold the vol down key while plugin in the usb-c cable (connected to your pc)
- keep holding
- you should get a white box with FTM factory test mode
- you are free to use adb again - so you can get into edl mode as well....
for pin part that'S normal while unlocking your device encryption gets deleted and you have to abort and factory reset your device in twrp....
Click to expand...
Click to collapse
Thanks. I tried it but it wont go to FTM. Only goes to diagnostic com port.
It seems i cant even turn it off. The little red light on the front is on the whole time .

sadly the disadvantage of a built in battery, so you have to wait till the battery is empty and try my instructions then....if it's not realy off it won't work, the mode you are currently in you usually only reach if you switch it on while holding both volume buttons, the edl mode is sadly not reachable with a key combination directly on G models.

adb don't show your device?

Starvirus said:
sadly the disadvantage of a built in battery, so you have to wait till the battery is empty and try my instructions then....if it's not realy off it won't work, the mode you are currently in you usually only reach if you switch it on while holding both volume buttons, the edl mode is sadly not reachable with a key combination directly on G models.
Click to expand...
Click to collapse
Oh ok. I expected ftm to work from vol-down and power-button till restart.
@adb: sadly no connection possible since it goes straight to Comport Connection.
Edit:
Couldnt make that work. It was off and i connected the usb. So it showed me the loading battery picture where i cant do anything. held the vol-down the whole time. But as soon as it had some battery it went straight to comport-connection again

im sorry to say, but ur device is bricked to a degree where you would need ZTEs Flashtool to fix it. Unfortunately we dont have that tool, so you might have to send it in

i have the same exact problem :'(
Have u been able to fix it?? I'm in a situation that i cant even send it to ZTE to fix it :'(

nsabir said:
i have the same exact problem :'(
Have u been able to fix it?? I'm in a situation that i cant even send it to ZTE to fix it :'(
Click to expand...
Click to collapse
Hi,
couldnt fix it myself so i had to send it in.
Unless some tool/rom was released in the last few months to fix it yourself i would guess your device is bricked.

Hi I have almost the same problem, I tried to unlock bootloader and now I don't have the recovery, I can boot and use my mobile but I can't restore it or update it because I don't have the recovery
I try whit axon7tool to restore the recovery but I got a error.

MaxRink said:
im sorry to say, but ur device is bricked to a degree where you would need ZTEs Flashtool to fix it. Unfortunately we dont have that tool, so you might have to send it in
Click to expand...
Click to collapse
Hi, do you have any idea, if there will be such a flashtool to work with DFU mode? I'm thinking that there are a lot of guys have bricked their devices (including me).
((

[HELP] Redmi Note 4(3+64) RED STATE

I have a redmi note 4 mediatek variant and it's been stuck in bootloop for the past 2 days. It keeps restarting and doesn't go into fastboot mode.
The bootloader is locked. It won't go into recovery or fastboot. Sometimes it turns on when holding the power button but then goes into a bootloop.
This was the message last displayed on the phone:
RED STATE
YOUR DEVICE HAS FAILED VERIFICATION AND MAY NOT WORK PROPERLY
YOUR DEVICE WILL BOOT IN 5 SECONDS
And then it shut down and hasn't responded since.
Going to a service center probably won't help since this is a chinese variant and I live in India. The service centers here are mostly useless.
All help is greatly appreciated.

You can always try to do test point. Download official rom file and flasher, make sure to install fastboot drivers. Take apart your phone and connect two golden contacts on the motherboard while plugging in USB cable connected to PC. The phone should boot up to bootloader and you should be able to flash rom.
Test points should look like this: http://en.miui.com/thread-646232-1-1.html (scroll down, there is one photo)
If you need anything you can e-mail me on [email protected]

timipisoboy said:
You can always try to do test point. Download official rom file and flasher, make sure to install fastboot drivers. Take apart your phone and connect two golden contacts on the motherboard while plugging in USB cable connected to PC. The phone should boot up to bootloader and you should be able to flash rom.
Test points should look like this: http://en.miui.com/thread-646232-1-1.html (scroll down, there is one photo)
If you need anything you can e-mail me on [email protected]
Click to expand...
Click to collapse
I somehow got it working by completely draining out the battery and then booting. It worked for a while normally (around 30 min) and then went into a bootloop again.

Help sort of "bricked" phone to unbrick!

My Asus Zenfone Max Pro M1 is stuck on the screen," Powered by Android". I have neither rooted nor unlocked the bootloader. I had received the error of "Your device is corrupted" and had followed the guide to remove that. For a month, my phone lagged and had a drop in battery. Restarting it has caused it to not work.Now, it's showing no signs of starting. Any help will be sincerely appreciated!

manav113 said:
My Asus Zenfone Max Pro M1 is stuck on the screen," Powered by Android". I have neither rooted nor unlocked the bootloader. I had received the error of "Your device is corrupted" and had followed the guide to remove that. For a month, my phone lagged and had a drop in battery. Restarting it has caused it to not work.Now, it's showing no signs of starting. Any help will be sincerely appreciated!
Click to expand...
Click to collapse
download 059 fastboot rom[search in forum you will find 059 fastboot rom. it is in-(how to use flashtool thread)]
unzip it.
connect your phone with pc as in fastboot mode.
double click on flashallAFT.bat or .cmd file from fastboot rom folder.
059 fresh installtion will be donw by this although you will lose all your data so please backup if possible.
after that if u still have that 'your device is corrupt' error follow my thread . corrupt state fix command dosnt mess with your system whatsoever. so either u deleted some files accidently or it got deleted during update. dont blame any buddy regarding that.

P53mutant said:
download 059 fastboot rom[search in forum you will find 059 fastboot rom. it is in-(how to use flashtool thread)]
unzip it.
connect your phone with pc as in fastboot mode.
double click on flashallAFT.bat or .cmd file from fastboot rom folder.
059 fresh installtion will be donw by this although you will lose all your data so please backup if possible.
after that if u still have that 'your device is corrupt' error follow my thread . corrupt state fix command dosnt mess with your system whatsoever. so either u deleted some files accidently or it got deleted during update. dont blame any buddy regarding that.
Click to expand...
Click to collapse
Thanks for Replying bro. TMy phone is not going to any mode ie neither fastboot nor recovery. Its only showing Powered by Android whatever combinations I go with.I am thinking to try the QFIL s/w.

manav113 said:
Thanks for Replying bro. TMy phone is not going to any mode ie neither fastboot nor recovery. Its only showing Powered by Android whatever combinations I go with.I am thinking to try the QFIL s/w.
Click to expand...
Click to collapse
go for qfil then but use 059 qfil otherwise 130 qfill u will lose your persist,factory,fsg partition. doownload 059 fastboot rom . it is combined fastboot qfill rom. use it same as other qfill rom but choose here ww_no-nfc_no-fsg raw program.
btw your device showing powered by android that means u can go into fastboot mode and recovery mode both. just press and hold power button untill u see restart of ur screen. as soon as u see that press violume up along with power key. u will def get acess to fastboot mode.

P53mutant said:
go for qfil then but use 059 qfil otherwise 130 qfill u will lose your persist,factory,fsg partition. doownload 059 fastboot rom . it is combined fastboot qfill rom. use it same as other qfill rom but choose here ww_no-nfc_no-fsg raw program.
btw your device showing powered by android that means u can go into fastboot mode and recovery mode both. just press and hold power button untill u see restart of ur screen. as soon as u see that press violume up along with power key. u will def get acess to fastboot mode.
Click to expand...
Click to collapse
Didn't worked.. QFIL s/w was not able to detect the port even after connecting the mobile.. Tried to completely discharge and recharge hoping it would work.. Now, its not even recharging.. Nothing works now..Feels like a motherboard problem now..Should I rebuy the 4GB version or look for another mobile?

Try asus service center

manav113 said:
Didn't worked.. QFIL s/w was not able to detect the port even after connecting the mobile.. Tried to completely discharge and recharge hoping it would work.. Now, its not even recharging.. Nothing works now..Feels like a motherboard problem now..Should I rebuy the 4GB version or look for another mobile?
Click to expand...
Click to collapse
motherboard issue not lead to sudden death of phone. did u encounter random reboot before every 10-20 mins if not no worry.
for qfill u have to turn off your phone and press vol + and vol - together and have to connect your hpone with pc. check device manager of pc it will show port and comt device 2-3 mins after successfull qualcomm diag port driver installation.

98har**** said:
Try asus service center
Click to expand...
Click to collapse
No response. They said they aren't able to fix it. Can give 1k for the lcd screen.. :crying:

P53mutant said:
motherboard issue not lead to sudden death of phone. did u encounter random reboot before every 10-20 mins if not no worry.
for qfill u have to turn off your phone and press vol + and vol - together and have to connect your hpone with pc. check device manager of pc it will show port and comt device 2-3 mins after successfull qualcomm diag port driver installation.
Click to expand...
Click to collapse
Didn't had any random reboot stuff. I thought voltage fluctuations might have affected it. I had charged it at the Airport the same day the phone gave up. The QFIL software was not able to detect port even while pressing vol+ and vol- .Service Centre tells me its a PCB problem and are asking 3k for repair. Looks like a new phone is somewhere in the line for future.

manav113 said:
Didn't had any random reboot stuff. I thought voltage fluctuations might have affected it. I had charged it at the Airport the same day the phone gave up. The QFIL software was not able to detect port even while pressing vol+ and vol- .Service Centre tells me its a PCB problem and are asking 3k for repair. Looks like a new phone is somewhere in the line for future.
Click to expand...
Click to collapse
well good riddance