Related
After Android tried to update itself to the newest version, it seemed that this failed and has caused a "boot failed" message. The tablet refuses to go into recovery mode, its marked as red. The only accessible mode is going into bootloader. After reading many forums and trying my luck with toolkits of all sorts (Nexus 7 Root Toolkit, Nexus Root Toolkit, Android SDK commands), the bootloader refuses to unlock. I have successfully installed the usb drivers since my pc recognizes the device. fastboot devices recognizes the devise but adb devices doesn't. The bootloader is locked and nothing else is accessible, whats worse is that through all of these toolkits and commands bootloader refuses to unlock, trying to unlock it always results in a failure message (unknown error). Commands such as format, unlock or erase fail in reviving the system. Anyone have any experience with this? I have searched for over a week now and im terribly frustrated by this. :silly:
AndiS21 said:
After Android tried to update itself to the newest version, it seemed that this failed and has caused a "boot failed" message. The tablet refuses to go into recovery mode, its marked as red. The only accessible mode is going into bootloader. After reading many forums and trying my luck with toolkits of all sorts (Nexus 7 Root Toolkit, Nexus Root Toolkit, Android SDK commands), the bootloader refuses to unlock. I have successfully installed the usb drivers since my pc recognizes the device. fastboot devices recognizes the devise but adb devices doesn't. The bootloader is locked and nothing else is accessible, whats worse is that through all of these toolkits and commands bootloader refuses to unlock, trying to unlock it always results in a failure message (unknown error). Commands such as format, unlock or erase fail in reviving the system. Anyone have any experience with this? I have searched for over a week now and im terribly frustrated by this. :silly:
Click to expand...
Click to collapse
do it the right way, dont use toolkits.
to unlock the bootloader, go into the bootloader(fastboot), connect the divice via usb, type..
fastboot devices(to make sure your device is visable)
fastboot oem unlock(to unlock the bootloader)
if you get an error, reboot the bootloader and try again. i had an error the first time on my replacement seven, second time it unlocked.
simms22 said:
do it the right way, dont use toolkits.
to unlock the bootloader, go into the bootloader(fastboot), connect the divice via usb, type..
fastboot devices(to make sure your device is visable)
fastboot oem unlock(to unlock the bootloader)
if you get an error, reboot the bootloader and try again. i had an error the first time on my replacement seven, second time it unlocked.
Click to expand...
Click to collapse
Thanks for the reply, i tried this several times, each time rebooting bootloader, but the command still posts an error in unlocking the bootloader. Recovery and Restart bootloader are marked in red font, Start is in Green, Power off White. I also tried flashing the recovery, since its inaccessible but because of bootloader being locked in won't allow me. :S Anything else you know that can be done ?
Reflash the bootloader?
edit: making VERY sure that you DON'T erase the existing bootloader first.
Try a manual update
AndiS21 said:
After Android tried to update itself to the newest version, it seemed that this failed and has caused a "boot failed" message. The tablet refuses to go into recovery mode, its marked as red. The only accessible mode is going into bootloader. After reading many forums and trying my luck with toolkits of all sorts (Nexus 7 Root Toolkit, Nexus Root Toolkit, Android SDK commands), the bootloader refuses to unlock. I have successfully installed the usb drivers since my pc recognizes the device. fastboot devices recognizes the devise but adb devices doesn't. The bootloader is locked and nothing else is accessible, whats worse is that through all of these toolkits and commands bootloader refuses to unlock, trying to unlock it always results in a failure message (unknown error). Commands such as format, unlock or erase fail in reviving the system. Anyone have any experience with this? I have searched for over a week now and im terribly frustrated by this. :silly:
Click to expand...
Click to collapse
You can try a manual update. Download the update and run adb sideload. That was not working for me, cause my Nexus it's allready updated, but hopefully it will work for you.
dave_uk said:
Reflash the bootloader?
edit: making VERY sure that you DON'T erase the existing bootloader first.
Click to expand...
Click to collapse
fortunatley though bootloader doesn't allow any command even the erase, it wouldn't allow me, nor formatting it as well. So i think the bootloader is intact. This is the screen i get from pressing Power and Vol Down.
pettymro said:
You can try a manual update. Download the update and run adb sideload. That was not working for me, cause my Nexus it's allready updated, but hopefully it will work for you.
Click to expand...
Click to collapse
As i have come to learn, adb can only function when debugging is enabled, in my device it wasn't unabled. Also the recovery program cannot be opened so sideloading through commands cannot be done. At least according to how some forums described the How To sideload through adb
try do it on another pc
AndiS21 said:
Thanks for the reply, i tried this several times, each time rebooting bootloader, but the command still posts an error in unlocking the bootloader. Recovery and Restart bootloader are marked in red font, Start is in Green, Power off White. I also tried flashing the recovery, since its inaccessible but because of bootloader being locked in won't allow me. :S Anything else you know that can be done ?
Click to expand...
Click to collapse
Can you post here the error message?
Israafiyl said:
Can you post here the error message?
Click to expand...
Click to collapse
Sure here it is. When i type in fastboot oem unlock, the message to unlock on my nexus comes up and when i click yes to unlock does the procedure start and end with failure.
AndiS21 said:
Sure here it is. When i type in fastboot oem unlock, the message to unlock on my nexus comes up and when i click yes to unlock does the procedure start and end with failure.
Click to expand...
Click to collapse
I don't know if fastboot let you flash the stock bootloader/recovery without unlocking but you may try:
fastboot flash bootloader bootloader-grouper-3.34.img
fastboot flash recovery recovery-stock-jro03d-nakasi.img
Israafiyl said:
I don't know if fastboot let you flash the stock bootloader/recovery without unlocking but you may try:
fastboot flash bootloader bootloader-grouper-3.34.img
fastboot flash recovery recovery-stock-jro03d-nakasi.img
Click to expand...
Click to collapse
thanks for the files, but bootloader won't allow me to change a single thing on it. Trying to flash recovery or the bootloader results in Failure result:bootloader locked!. :S
AndiS21 said:
thanks for the files, but bootloader won't allow me to change a single thing on it. Trying to flash recovery or the bootloader results in Failure result:bootloader locked!. :S
Click to expand...
Click to collapse
try one more time with a different port/pc if it daesn't work it may be a hardware fault, i think a corrupted sd.
(you will have to send it to warranty but don't worry, asus have a really good assistence, you may have a new nexus in a less than 2 days)
Manual update
AndiS21 said:
As i have come to learn, adb can only function when debugging is enabled, in my device it wasn't unabled. Also the recovery program cannot be opened so sideloading through commands cannot be done. At least according to how some forums described the How To sideload through adb
Click to expand...
Click to collapse
Use the volume up/down keys to navigate to "Recovery mode", then press the power button.
When the Android with the red exclamation point appears, hold down power first, followed quickly by volume down and volume up. (So that to start, you're holding down power, then you're holding down all three). After 2-3 seconds, release all three keys.
Use the volume up/down keys to select "apply update from ADB," then press power to select it.
On your computer, open up a command prompt or terminal window.
Using the command line, navigate to the folder containing the ADB executables and the update file.
type:
adb.exe sideload <update filename>
On my Nexus with Jelly 4.2 usb debugging is not enabled too, but I still get the option in recovery mode menu. Operation not succesful cause I cannot upgrade from 4.2 to 4.2. I will wait for another update and then try it again. Good luck!
Israafiyl said:
try one more time with a different port/pc if it daesn't work it may be a hardware fault, i think a corrupted sd.
(you will have to send it to warranty but don't worry, asus have a really good assistence, you may have a new nexus in a less than 2 days)
Click to expand...
Click to collapse
I tried it on the laptop too, even changed the drivers to universal naked drivers, but nothing! Restart bootloader is with red, clicking it wont reboot the tablet, also recovery mode red, the only working button is the Start (green) but that leads to boot failure and power off.
pettymro said:
Use the volume up/down keys to navigate to "Recovery mode", then press the power button.
When the Android with the red exclamation point appears, hold down power first, followed quickly by volume down and volume up. (So that to start, you're holding down power, then you're holding down all three). After 2-3 seconds, release all three keys.
Use the volume up/down keys to select "apply update from ADB," then press power to select it.
On your computer, open up a command prompt or terminal window.
Using the command line, navigate to the folder containing the ADB executables and the update file.
type:
adb.exe sideload <update filename>
On my Nexus with Jelly 4.2 usb debugging is not enabled too, but I still get the option in recovery mode menu. Operation not succesful cause I cannot upgrade from 4.2 to 4.2. I will wait for another update and then try it again. Good luck!
Click to expand...
Click to collapse
recovery mode cannot be opened, the text font is red on the tablet and clicking it does nothing. :S
Also tried to completley flash the device but unable to. Going back and doing an fastboot oem unlock yields the same feedback.
Unlock Bootloader on 4.2
Hello, I was wondering if the bootloader in 4.2 can be unlocked the same way as it was on 4.1.2? I recently got a new nexus 7 and updated to 4.2.
Thanks and Cheers!
After some research into my issue, i have discovered that other users have posted "unbricking" solutions through a program called nvflash, when the device is put in APX mode. But unfortunatley i've yet to find a nvflash solution for nexus 7. I will experiment with the commands and what the others have reported as a solution.
ErnestoV31 said:
Hello, I was wondering if the bootloader in 4.2 can be unlocked the same way as it was on 4.1.2? I recently got a new nexus 7 and updated to 4.2.
Thanks and Cheers!
Click to expand...
Click to collapse
Yes it can.
Sent from my GT-I9300 using Tapatalk 2
Hello all! I'm having a problem with a Nexus 7.
This is my brother's tablet that he hasn't used in a few months. It hasn't been unlocked or rooted.
I can get to the boot screen with the android lying on it's back and the options with the volume buttons. The other info on that screen which might be pertinent:
Fastboot mode
Product name: grouper
variant - grouper
hw version - er3
bootloader version - n/a
serial number -
signing - not defined yet
lock stated - locked
When I go to recovery mode and push the power button, it says "booting failed" in the upper left. It still says Google in the middle, and has the options with the volume in the upper right, but the android is gone as is the text in the lower left.
I have adb and fastboot installed, but I can't seem to do much since the tablet is locked. I tried unlocking a few times, and it's always failed. Usually it doesn't give a reason, but one time I got this: "Failed (status read failed (Too many links))"
I've tried googling this and can't find someone with the same problem.
Anything I can try?
Thanks!
Nexus Tool Kit
rbeavers said:
Nexus Tool Kit
Click to expand...
Click to collapse
OK, I have that now, but I can't get very far. I think I need to enable debugging on the device first? How can I do that in that state it's in now?
swirv81 said:
OK, I have that now, but I can't get very far. I think I need to enable debugging on the device first? How can I do that in that state it's in now?
Click to expand...
Click to collapse
Anything else I can try? Not sure if I'm missing something with the tool kit, but I nothing I tried seemed to help.
swirv81 said:
Anything else I can try? Not sure if I'm missing something with the tool kit, but I nothing I tried seemed to help.
Click to expand...
Click to collapse
If you can get into the Bootloader, just run the below via ADB
Code:
fastboot oem unlock
Once you unlock the Bootloader you can use the "Soft Brick" Mode in the NRT to Re-flash back to stock and see if that will allow you to boot. You do not need debugging enabled to use the Nexus Root Toolkit if you use the Soft Brick mode, but you must have an unlocked bootloader.
ariesgodofwar said:
If you can get into the Bootloader, just run the below via ADB
Code:
fastboot oem unlock
Once you unlock the Bootloader you can use the "Soft Brick" Mode in the NRT to Re-flash back to stock and see if that will allow you to boot. You do not need debugging enabled to use the Nexus Root Toolkit if you use the Soft Brick mode, but you must have an unlocked bootloader.
Click to expand...
Click to collapse
I've tried unlocking a few times, but after a few minutes of it saying "unlocking" it fails.
swirv81 said:
I've tried unlocking a few times, but after a few minutes of it saying "unlocking" it fails.
Click to expand...
Click to collapse
What says "unlocking" (computer or tablet) and are you trying to do it through the Toolkit, or via command prompt ADB? I would first make sure your computer is seeing your tablet (ie. that the drivers and Fastboot are installed correctly). Do you know that they are?
ariesgodofwar said:
What says "unlocking" (computer or tablet) and are you trying to do it through the Toolkit, or via command prompt ADB? I would first make sure your computer is seeing your tablet (ie. that the drivers and Fastboot are installed correctly). Do you know that they are?
Click to expand...
Click to collapse
I was trying this with the command prompt. I could get fastboot to list the device when using that command. And the tablet and command prompt both say "unlocking" when doing that. I would assume that means the computer is seeing the tablet and everything is set up correctly?
I think I tried to unlock with the Toolkit, but I believe it told me that device needs to be in debugging mode.
Hey there, I'm having a similar problem.
My info is the same except my bootloader version is 4.18 and my lock state says it's unlocked. I tried to use the root kit but I'm having trouble with the fastboot device being detected. Driver solutions attempted were the google ones, and the pdanet ones. I can't really do the manual thing since that involves the device being recognized when plugged in, and since I can't enable usb debugging... anyways the automated drivers windows says were installed successfully so I don't really know what else to do.
Note: I do know the usb port on the tablet and computer work since when plugged in, it will show that its charging with the white battery icon.
Same issue here
I was in the process of upgrading manually from android 5.0 to 5.0.2 owing to the serious lag that came with lollipop. The OTA was taking longer and testing my patience as most apps were crashing due to lag.
Therefore decided to go for manual flashing of the image. I have never done this before. I was able to make the computer see my device by disabling mtp via storage under setting in the device. This is one thin I noticed to make the device visible to the computer.
After installing the device drivers my nexus was visible within the device manager but it couldn't be seen as an external storage until I played with the MTP. I had even unlocked the boot loader before all this.
So everything was going well and while I started to think all is well, I ran into this issue. From adb I tried to run 'flash-all.bat' from the new device image. Something went wrong somewhere - don't know what it is, but from then on, I am stuck in the fastboot screen or into recovery mode but when i try to boot the device bu hitting the power button - I get this message 'Booting failed'.
I am also trying to use NRToolkit but no use. When I connect my device it is seen in the device manager in my pc but cannot see it as a storage. Therefore when I now try to run the 'adb devices' command it cannot see my device. From what I saw initially, until I enable/disable mtp mode adb was not able to see my device to communicate.
Now when I tried NRT and installed the drivers once again, it is being detected in the device manager but when I run the driver test within NRT - I get a ADB device not found error. Within NRT all that it says is go into device setting>storage to enable it which I know but at the current status of my device in boot screen/recovery mode how can I go in to enable this. This is not helpful.
Somebody please suggest a workaround for this issue. I know I am close to the solution but not sure how to enable the MTP or at least made the NRToolkit to say 'ADB device found'.
My fastboot screen shows these details:
Fastboot mode
Product name grouper
Variant = grouper
HW Version – ER3
Bootloader version – 4.23
Baseband version – N/A
Serial number – 015d21d910141c0a
Signing – not defined yet
Lock State - unlocked
Please help.
Hi guys,
a week ago my ZUK Z1 started to bootloop without any evident reason.
I found it in this state picking it up from my pocket, so I guessed it was due to some random reboot that occasionally happened to it.
So, stating that:
- I'm with original stock CyanogenOS,
- I never rooted, or even accessed to the recovery menu prior to this event,
- I'm perfectly able now to communicate and send commands to device via adb or in fastboot mode,
problem is that I did NOT enable "USB debugging" and I did NOT OEM unlock when I had the chance to reach Developer options menu through the Android GUI (now I'm blocked by bootloop), resulting in an obvious "no unlocked device" error message each time I try to flash or write system partitions.
The output from "fastboot oem get-info" confirms this status.
I'm operating from a shell with adiministrator's grant in Windows 8.
No luck with "fastboot oem unlock", "fastboot flashing unlock_critical" or "adb root".
I used also "-i 0x2b4c" (vendor code) option in my commands.
Then, my question for you:
is there still a way to unlock bootloader in order to recover with CyanogenOS stock image, in this condition?
I saw there's a "debuggable" image on Cyanogen site, but I've no hint on how to use it and if it could help me.
Maybe ZUK has to provide to me an unlock key: I read on this forum that OnePlus and Huawei have similar option.
Thanks a lot in advance for any hint and suggestion you can give to me.
---------- Post added at 05:43 PM ---------- Previous post was at 05:43 PM ----------
[/COLOR]
dalviking said:
Hi guys,
a week ago my ZUK Z1 started to bootloop without any evident reason.
I found it in this state picking it up from my pocket, so I guessed it was due to some random reboot that occasionally happened to it.
So, stating that:
- I'm with original stock CyanogenOS,
- I never rooted, or even accessed to the recovery menu prior to this event,
- I'm perfectly able now to communicate and send commands to device via adb or in fastboot mode,
problem is that I did NOT enable "USB debugging" and I did NOT OEM unlock when I had the chance to reach Developer options menu through the Android GUI (now I'm blocked by bootloop), resulting in an obvious "no unlocked device" error message each time I try to flash or write system partitions.
The output from "fastboot oem get-info" confirms this status.
I'm operating from a shell with adiministrator's grant in Windows 8.
No luck with "fastboot oem unlock", "fastboot flashing unlock_critical" or "adb root".
I used also "-i 0x2b4c" (vendor code) option in my commands.
Then, my question for you:
is there still a way to unlock bootloader in order to recover with CyanogenOS stock image, in this condition?
I saw there's a "debuggable" image on Cyanogen site, but I've no hint on how to use it and if it could help me.
Maybe ZUK has to provide to me an unlock key: I read on this forum that OnePlus and Huawei have similar option.
Thanks a lot in advance for any hint and suggestion you can give to me.
Click to expand...
Click to collapse
Sideload the official stock rom with zuk z1 tool. That s how i managed to un-brick my zuk. Download the stock rom , cm-12.1-YOG4PAS3OH-ham-signed.zip from this page https://cyngn.com/support. Use the toolkit provided here : http://forum.xda-developers.com/zuk-...alpha-t3235964 to sideload the rom. Wait until the phone restarts and thats it. You must also install adb and fastboot and have adb driver installed.I used the shenqi adb composite driver, but i guess the universal adb driver can work too. I had the same problem. Stuck in bootloop with USB debugging not enabled and bootloader locked.
Or you can try to fastboot the stock rom with the command provided in this useful tool.
Extentho said:
---------- Post added at 05:43 PM ---------- Previous post was at 05:43 PM ----------
[/COLOR]
Sideload the official stock rom with zuk z1 tool. That s how i managed to un-brick my zuk. Download the stock rom , cm-12.1-YOG4PAS3OH-ham-signed.zip from this page https://cyngn.com/support. Use the toolkit provided here : http://forum.xda-developers.com/zuk-...alpha-t3235964 to sideload the rom. Wait until the phone restarts and thats it. You must also install adb and fastboot and have adb driver installed.I used the shenqi adb composite driver, but i guess the universal adb driver can work too. I had the same problem. Stuck in bootloop with USB debugging not enabled and bootloader locked.
Or you can try to fastboot the stock rom with the command provided in this useful tool.
Click to expand...
Click to collapse
Thanks a lot Extentho for your feedback.
I've already tried your fair suggestion: unfortunately, I'm stuck at the end of sideloading the signed .zip.
In fact, I see on screen logs that it's applying the update "unconditionally" (that sounds good), but nevertheless, when finished it returns "xfer: 1.00x" on PC shell and in recovery menu, on device.
Now, either if I reboot or power down and boot it again, the result is the same: still bootloop-ing.
Of course, at any other attempts leveraging on administrative privilege, it says that "device is locked", including those done through the shell tool.
Some excerpts from my last launched commands:
c:\_APP\CM>adb devices
List of devices attached
51f8941d sideload
c:\_APP\CM>adb shell
error: closed
c:\_APP\CM>adb kill-server
c:\_APP\CM>adb root
error: closed
c:\_APP\CM>adb kill-server
c:\_APP\CM>adb usb
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
error: closed
c:\_APP\CM>adb kill-server
c:\_APP\CM>adb devices
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
List of devices attached
51f8941d sideload
c:\_APP\CM>adb sideload cm-12.1-YOG4PAS3OH-ham-signed.zip
Total xfer: 1.00x
You must have the phone in sideload mode. There is an option to sideload in recovery menu.
Then use the command to sideload from the toolkit. The stock rom must pe renamed sideload and placed on desktop.
If the phone communicates in any way with pc, there is still hope. When you start the sideload process from pc, the phone should show an animation showing the flashing process. Post some pictures from where you are stuck, so i can make an idea about what is going on
my zuk z1 stuck to bootloop,
and android debugging is disabled.
phone can not detecting in fastboot mode.
please help.
Extentho said:
You must have the phone in sideload mode. There is an option to sideload in recovery menu.
Then use the command to sideload from the toolkit. The stock rom must pe renamed sideload and placed on desktop.
If the phone communicates in any way with pc, there is still hope. When you start the sideload process from pc, the phone should show an animation showing the flashing process. Post some pictures from where you are stuck, so i can make an idea about what is going on
Click to expand...
Click to collapse
I've tried also with the toolkit, but it's heavy bugged (also in 5.4 version) and, after all, it gets the exact same problem like me (not surprising, it launches my same commands ).
There's no useful image or snapshot I can share, because I see the animated green android logo moving its antennas on my device, while logs below saying that it's verifying package and then it's unconditionally overwriting system partition.
It seems all so normal and plain.
At the end of the process, no "installation complete" message, but simply I get back to recovery menu (where I started from).
In other attempts, I also wiped cache and user data, prior to rebooting, just to test if it was going to change something, but no luck.
The phone reboots, the "Cyanogen" logo starts to glow for 7/8 times and then... bzzzz, short vibration and all over again (i.e. bootloop).
I tried with an older official signed .zip from Cyanogen OS (cm-12.1-YOG4PAS3AJ-ham-signed, instead of newer cm-12.1-YOG4PAS3OH-ham-signed), but even worst, it fails at "verify package" step, aborting procedure.
MD5 signatures triple-checked each time versus source.
I saw some threads where it seems possible to change the bit, on system image, controlling developer option, to manually post-enable unlocking, but it's suitable only for Nexus or OnePlus One. No instructions for ZUK Z1.
Or maybe do I need a "donor" sharing a stock .zip with this option yet enabled?
Bootloop would be still there, but I possibly could enable to "flash", "boot" and "shell" vs the device, giving me much more options to try.
One last doubt anyway. If I press "Volume Down" + "Power" button at boot, I get into a menu like this:
http: // postimg.org/image/s5badiefh/ (remove extra spaces).
Viewing other examples posted on forums, I noted that at least the "Factory reset" is missing.
Could it be an hint for anything useful?
dalviking said:
I've tried also with the toolkit, but it's heavy bugged (also in 5.4 version) and, after all, it gets the exact same problem like me (not surprising, it launches my same commands ).
There's no useful image or snapshot I can share, because I see the animated green android logo moving its antennas on my device, while logs below saying that it's verifying package and then it's unconditionally overwriting system partition.
It seems all so normal and plain.
At the end of the process, no "installation complete" message, but simply I get back to recovery menu (where I started from).
In other attempts, I also wiped cache and user data, prior to rebooting, just to test if it was going to change something, but no luck.
The phone reboots, the "Cyanogen" logo starts to glow for 7/8 times and then... bzzzz, short vibration and all over again (i.e. bootloop).
I tried with an older official signed .zip from Cyanogen OS (cm-12.1-YOG4PAS3AJ-ham-signed, instead of newer cm-12.1-YOG4PAS3OH-ham-signed), but even worst, it fails at "verify package" step, aborting procedure.
MD5 signatures triple-checked each time versus source.
I saw some threads where it seems possible to change the bit, on system image, controlling developer option, to manually post-enable unlocking, but it's suitable only for Nexus or OnePlus One. No instructions for ZUK Z1.
Or maybe do I need a "donor" sharing a stock .zip with this option yet enabled?
Bootloop would be still there, but I possibly could enable to "flash", "boot" and "shell" vs the device, giving me much more options to try.
One last doubt anyway. If I press "Volume Down" + "Power" button at boot, I get into a menu like this:
http: // postimg.org/image/s5badiefh/ (remove extra spaces).
Viewing other examples posted on forums, I noted that at least the "Factory reset" is missing.
Could it be an hint for anything useful?
Click to expand...
Click to collapse
For me, this method worked exactly as described, booting into stock rom correctly.
now, if you mentioned it in the picture, there is another option. so, i ve noticed too this menu. There is an app called QPST wich can help you. Follow this thread: http://forum.xda-developers.com/zuk-z1/help/bricked-zuk-z1-t3277257 .
So when you enter in QFIL, connect the phone to computer and boot with volume down+ power into this menu from your picture. The Qfil app should detect some ports. You must choose the 9008 one, from what i have read.
Anyway, for me this method, didn t work because the pc couldn t detect the right port, only the zuk tookit did it for me.
You read the thread i suggested, and try that method, it may work for you.
Extentho said:
For me, this method worked exactly as described, booting into stock rom correctly.
now, if you mentioned it in the picture, there is another option. so, i ve noticed too this menu. There is an app called QPST wich can help you. Follow this thread: http://forum.xda-developers.com/zuk-z1/help/bricked-zuk-z1-t3277257 .
So when you enter in QFIL, connect the phone to computer and boot with volume down+ power into this menu from your picture. The Qfil app should detect some ports. You must choose the 9008 one, from what i have read.
Anyway, for me this method, didn t work because the pc couldn t detect the right port, only the zuk tookit did it for me.
You read the thread i suggested, and try that method, it may work for you.
Click to expand...
Click to collapse
Thanks again Extentho.
I saw QPST trick, but it's not catching right port and/or not getting right permission to stop phone from re-booting.
I think that adb/toolkit method should work also for me. I made attempts with other official ROMs: I noticed that for the older ones, the result is a bit different. They get stuck in a "black screen + notify led lighted in blue" state, rather than bootlooping.
Maybe erasing system partitions is needed, but I'm very reluctant to such dangerous way, without expertised advice.
Weirdest thing is that I did anything to get this situation, I just found my device in this mess.
Of course ZUK official support is well silent at my requests.
dalviking said:
Thanks again Extentho.
I saw QPST trick, but it's not catching right port and/or not getting right permission to stop phone from re-booting.
I think that adb/toolkit method should work also for me. I made attempts with other official ROMs: I noticed that for the older ones, the result is a bit different. They get stuck in a "black screen + notify led lighted in blue" state, rather than bootlooping.
Maybe erasing system partitions is needed, but I'm very reluctant to such dangerous way, without expertised advice.
Weirdest thing is that I did anything to get this situation, I just found my device in this mess.
Of course ZUK official support is well silent at my requests.
Click to expand...
Click to collapse
Try to post some pics about the troubles you encounter. If we receive a solution, this may be helpful for all of us in the future. Now, exactly, what can you acces on phone(recovery, fastboot, )?
Also, check varios threads from other phones with the same problems(one plus one, lg , htc) ,etc. Find a solved situation like yours, and we may adapt that solution to you
Hi guys,
Just to close this topic.
I was finally able to install the ZUI ROM through the QFIL program.
It's a little bit tricky, due to the fact that it is strongly suggested:
- to use a Windows 7 machine started without Signature Enforcement enabled;
- to start QFIL (admin mode) and be prepared with all needed files loaded in its GUI;
- to power off the phone, then, while pressing volume up button, inserting the USB cable, attached (better if) on a 2.0 port to PC;
- to be fast pressing "Download" button on QFIL program.
After that, I unlocked the bootloader and performed a lot of alternative recovery process.
So, I installed on the device:
- ZUI ROM
- Cyanogen OS convert from ZUI ROM
- Cyanogen OS last updated ROM
- CyanogenMod 12.1 last nightly ROM
- CyanogenMod 13.0 last nightly ROM
and the winner is...
...
...
...
... none of the above.
Each time the very same behaviour: bootloop. So, my last conclusion is: hardware failure (I guess wi-fi module).
I give up.
But for anyone searching a safe way to unlock a bootloader without accessing to developer options: the QFIL method works like a charm (once installed properly).
Thanks for support.
Messed my zuk z1
I tried to flash stock room in my zuk z1 , I downloaded Qualcomm file for the ROM and installed the required in my laptop,I wiped all data in my phone using TWRP .though my power button is not working I used tool kit to reboot my phone by connecting into fast boot mode,here comes the prob by mistake I entered the wrong command which locks my bootloader .I don't know what to do...help me.....
Hi i need to unroot and factory reset the phone. Oneplus 2 What ive already done or tried: I started to try unrooting it through superSU but that didnt work i just waited waited and nothing hapened. so then i tried to fastboot img but just got error the device is locked even though i did enable oem unluck and usb debuging. so then i wrote in cmd: fastboot oem unlock and now the phone starts up to the op logo then restard into it again after a second D'=
Im not familiar with forums and very stressed to get my phone working so i would be very very gratefull for help.
now i cant even charge it the batery logo doesnt come up after i did fasboot oem unlock again.... rip
spacebite said:
Hi i need to unroot and factory reset the phone. Oneplus 2 What ive already done or tried: I started to try unrooting it through superSU but that didnt work i just waited waited and nothing hapened. so then i tried to fastboot img but just got error the device is locked even though i did enable oem unluck and usb debuging. so then i wrote in cmd: fastboot oem unlock and now the phone starts up to the op logo then restard into it again after a second D'=
Im not familiar with forums and very stressed to get my phone working so i would be very very gratefull for help.
Click to expand...
Click to collapse
spacebite said:
no i cant even charge it the batery logo doesnt come up after i did fasboot oem unlock again.... rip
Click to expand...
Click to collapse
Got to OnePlus support center and go in download section and download official ROM. Hold power and volume up bottons and connect it to PC. After that go in folder where adb files are located on your PC (If you don't have them, search on Google for "adb install 15 sec"). Hold left shift on your keyboard and right click your mouse in that folder on an empty space. Click something related with command window and type "fastboot devices". If you get some kind of feedback it's 2minute of work! If you don't have anything come up, try to start your device in fastboot mode again (second sentence in this post). After you got a feedback from command "fastboot devices" flash custom recovery (I suggest TWRP, Google it and download the .IMG file for your device). To flash a custom recovery type this in command line: "fastboot flash recovery IMAGE_NAME.img"
*replace IMAGE_NAME with actual image name...
After that boot in recovery by disconnecting the phone and powering off the phone. Press and hold power button and volume down buttons till blue TWRP logo appears. After that connect your device on PC and transfer your .Zip file(ROM) to internal memory of your device. You should go back to main menu of recovery and select wipe>advanced wipe, select everything BUT INTERNAL STORAGE!!!***IMPORTANT***
Then you just install ROM like you would normally do...
Press thanks it i helped! Hope I didn't missed something.
This is written in mind with that you have unlocked bootloader like you have written in your post...
x8Cooler said:
Got to OnePlus support center and go in download section and download official ROM. Hold power and volume up bottons and connect it to PC. After that go in folder where adb files are located on your PC (If you don't have them, search on Google for "adb install 15 sec"). Hold left shift on your keyboard and right click your mouse in that folder on an empty space. Click something related with command window and type "fastboot devices". If you get some kind of feedback it's 2minute of work! If you don't have anything come up, try to start your device in fastboot mode again (second sentence in this post). After you got a feedback from command "fastboot devices" flash custom recovery (I suggest TWRP, Google it and download the .IMG file for your device). To flash a custom recovery type this in command line: "fastboot flash recovery IMAGE_NAME.img"
*replace IMAGE_NAME with actual image name...
After that boot in recovery by disconnecting the phone and powering off the phone. Press and hold power button and volume down buttons till blue TWRP logo appears. After that connect your device on PC and transfer your .Zip file(ROM) to internal memory of your device. You should go back to main menu of recovery and select wipe>advanced wipe, select everything BUT INTERNAL STORAGE!!!***IMPORTANT***
Then you just install ROM like you would normally do...
Press thanks it i helped! Hope I didn't missed something.
This is written in mind with that you have unlocked bootloader like you have written in your post...
Click to expand...
Click to collapse
thanks i will try when i get home
Fallow this and don't trust any guides written out of memory with likely any mistakes.. (no offense)
This guide has various approaches to recover your phone, remember to research first and don't type carelessly any adb commands, it's not enough to just tick "oem unlock" in developer options, you'd have to type command on fastboot too, to unlock the bootloader.. there are many guides and youtube tutorials on this subject, absolutely unnecessary to blindly kill it, anyways I'll never understand how you can be so reckless with your phone..
https://forums.oneplus.net/threads/...ck-guide-for-a-hard-bricked-oneplus-2.347607/
Edit: the state you brought your phone into is called "hard bricked" - have fun..
Sent from my OnePlus2 using XDA Labs
spacebite said:
thanks i will try when i get home
Click to expand...
Click to collapse
Don't!
If you get no joy from following the instructions in the link given by @Sam Nakamura, try @fareed_xtreme's Official OP2 Stock Reset to OOS 3.0.2
Sam Nakamura said:
Fallow this and don't trust any guides written out of memory with likely any mistakes.. (no offense)
This guide has various approaches to recover your phone, remember to research first and don't type carelessly any adb commands, it's not enough to just tick "oem unlock" in developer options, you'd have to type command on fastboot too, to unlock the bootloader.. there are many guides and youtube tutorials on this subject, absolutely unnecessary to blindly kill it, anyways I'll never understand how you can be so reckless with your phone..
https://forums.oneplus.net/threads/...ck-guide-for-a-hard-bricked-oneplus-2.347607/
Edit: the state you brought your phone into is called "hard bricked" - have fun..
Sent from my OnePlus2 using XDA Labs
Click to expand...
Click to collapse
Aight thank you i had some suspicion it might be ...-bricked didnt know which though so thank you
If you can get in the bootloader then possibly the device is still OK. Just need to get the right ROM.
Try different TWRP versions. Sometimes, one particular version can save the world.
So I looked around here and on the interwebz to find an answer to my question before I decided to state my question to you.
I just acquired the Sony Xperia X Compact (F5321; Android 7.1.1).
In order to get TWRP on it, I consulted a lot of online guides including those described here. Of which I thought this would be the most suitable:
https://forum.xda-developers.com/x-compact/development/recovery-twrp-3-1-1-xperia-x-compact-t3640914
So after:
having adb tools and fastboot incl. drivers (also tried the minimal)
developer options -- oem unlocking -- bootloader allowed to be unlocked; and developer options -- USB debugging -- debug mode when USB is connected
checking the service *#*#7378423#*#* , which shows "bootloader unlock allow : YES"
phone connected to PC
I encounter the following problem.
While the sony stock rom it comes with is running,
via adb I am able to feed the phone the following command with the respective outcome:
adb reboot fastboot (reboots into Android, with the LED lighting briefly up in red)
adb reboot recovery (reboots into Android, with the LED lighting briefly up in red)
adb reboot bootloader (boots down, but does not boot into Android; there is only a black screen and the LED is on and stays blue)
in any of those states, if I enter an adb command there is always this output as if the phone wasn't connected or recognized or off:
error: device '(null)' not found
So I am able to communicate commands to the phone when it is running. I assume this means my drivers are all in order, right?
Also. While it is off and disconnected from the PC.
I keep the power button and the volume down button pressed, the Sony Logo comes up and after that it takes turns with a black screen as long as I keep pressed.
I keep the power button and the volume up button pressed. It is followed by one short vibration, another short one, and the three in a row. And then no further reaction.
I feel pretty dumb, can anyone help me with how to enter any of the alternative boot options? Thanks in advance!
I just don't know if there is something I am not seeing or if there is plainly something wrong with the phone. Not knowing this for sure is driving me crazy. Hopefully this is something others might learn from, as well.
____________
little edit about the text format
From your description, it seems like TWRP was not installed correctly. But don't worry, on this phone you do not have to install the recovery to use it. You can boot straight into recovery from your PC while the phone is in 'fastboot' mode. The 'fastboot' mode is what you get when you do 'adb reboot bootloader'. The screen off, blue LED is signalling that the phone is ready for fastboot commands. You can then run:
Code:
fastboot boot <recovery image file>
The phone should load and run the recovery.
Please note that adb will not see your device while it is in fastboot mode. Likewise, fastboot does not work while the phone is accessible through adb. adb support comes from the ROM, but TWRP also supports adb, so you can also use adb while in TWRP.
Rendini said:
So I looked around here and on the interwebz to find an answer to my question before I decided to state my question to you.
I just acquired the Sony Xperia X Compact (F5321; Android 7.1.1).
In order to get TWRP on it, I consulted a lot of online guides including those described here. Of which I thought this would be the most suitable:
https://forum.xda-developers.com/x-compact/development/recovery-twrp-3-1-1-xperia-x-compact-t3640914
So after:
having adb tools and fastboot incl. drivers (also tried the minimal)
developer options -- oem unlocking -- bootloader allowed to be unlocked; and developer options -- USB debugging -- debug mode when USB is connected
checking the service *#*#7378423#*#* , which shows "bootloader unlock allow : YES"
phone connected to PC
I encounter the following problem.
While the sony stock rom it comes with is running,
via adb I am able to feed the phone the following command with the respective outcome:
adb reboot fastboot (reboots into Android, with the LED lighting briefly up in red)
adb reboot recovery (reboots into Android, with the LED lighting briefly up in red)
adb reboot bootloader (boots down, but does not boot into Android; there is only a black screen and the LED is on and stays blue)
in any of those states, if I enter an adb command there is always this output as if the phone wasn't connected or recognized or off:
error: device '(null)' not found
So I am able to communicate commands to the phone when it is running. I assume this means my drivers are all in order, right?
Also. While it is off and disconnected from the PC.
I keep the power button and the volume down button pressed, the Sony Logo comes up and after that it takes turns with a black screen as long as I keep pressed.
I keep the power button and the volume up button pressed. It is followed by one short vibration, another short one, and the three in a row. And then no further reaction.
I feel pretty dumb, can anyone help me with how to enter any of the alternative boot options? Thanks in advance!
I just don't know if there is something I am not seeing or if there is plainly something wrong with the phone. Not knowing this for sure is driving me crazy. Hopefully this is something others might learn from, as well.
____________
little edit about the text format
Click to expand...
Click to collapse
Switch the phone off.
To enter fastboot mode: Hold the Volume UP and connect your phone to the USB port of your PC. The blue LED should come on and provided you have correctly installed drivers, you will be able to use fastboot commands.
To enter bootloader/flashmode: Hold Volume DOWN button and plug USB cable to your PC. Green LED should lit up and provided you have correctly installed the drivers, you will be able to use Flashtool, Emma or other software to flash firmware files.
FAILED (remote: Command not allowed)
Hey guys!
First of all, thanks for taking the time!
So, confirming how to enter bootloader/flashmode is much appreciated, since I was very much in doubt about the fact that the screen stayed off. On other devices I always had something on the screen in recovery mode and the like.
Now I know it was problem with the drivers indeed. Also appreciated, the hint that adb and fastboot work separately. While the device was recognized by adb when it was turned on, it was not in fastboot mode because of missing drivers. Finally it is being recognized and I can address the device via fastboot command.
And yet, I have the next brick wall. Any command I send via fastboot is answered by this output:
Code:
FAILED (remote: Command not allowed)
up to this point, I have not found one command that is being acknowledged and triggers another output, so I think it is a general problem. Maybe still with the drivers. Any hints would be celebrated. Anyways, in the meantime I will keep on trying until I succeed or until I get too frustrated and send it back and never try Sony devices again
not kidding XD
Rendini said:
Hey guys!
First of all, thanks for taking the time!
So, confirming how to enter bootloader/flashmode is much appreciated, since I was very much in doubt about the fact that the screen stayed off. On other devices I always had something on the screen in recovery mode and the like.
Now I know it was problem with the drivers indeed. Also appreciated, the hint that adb and fastboot work separately. While the device was recognized by adb when it was turned on, it was not in fastboot mode because of missing drivers. Finally it is being recognized and I can address the device via fastboot command.
And yet, I have the next brick wall. Any command I send via fastboot is answered by this output:
Code:
FAILED (remote: Command not allowed)
up to this point, I have not found one command that is being acknowledged and triggers another output, so I think it is a general problem. Maybe still with the drivers. Any hints would be celebrated. Anyways, in the meantime I will keep on trying until I succeed or until I get too frustrated and send it back and never try Sony devices again
not kidding XD
Click to expand...
Click to collapse
because your bootloader is not unlocked. you have set your bootloader to allow unlocking in developers options, but you need to do the actual unlock using "fastboot unlock" command. you need a unique unlock code from Sony Developers portal and keep in mind that unlocking your device irrevocably deletes DRM keys. it is advisable that you backup your DRM keys before unlocking your device.
the problem is not Sony device, but your unability to read and follow guides and get yourself informed and educated before you dive into trial and error, finaly blaming manufacturer for your own faults...