Hello
I installed lineage os that on form then I flashed hex file
After that phone won't open .. Not even shows on PC
Tryid everything
Only when I put cable in phone ., red led shows but can't open phone or even lenovo logo shows
Any idea to try read phone plug in on PC to flash ROM again???
Related
Hello, I have bought Jiayu S3 recently, for those who don't know, it is a phone featuring mediatek mtk6752. It was all good but I decided to restore factory settings and phone seems to be bricked. I have watched many tutorials and read guides but nothing helps. My phone blinks with android logo continuosly, once per few seconds it displays android with red exclamation mark inside of his body. I have tried to do recovery but phone only resets showing Jiayu logo or turns off completely. Obviously I have tried to flash stock rom but my phone is not recognized by the PC, and no held buttons combination helps. It does recognize it with the battery in but I can't flash with it in, right? I have tried removing mediatek usb drivers, redownloading them, flashing stock rom by different programs, but the phone is just not recognized. I have read something about hard reset (which includes working with the hardware) but I hope there is another non invasive solution.
HooCairs said:
Hello, I have bought Jiayu S3 recently, for those who don't know, it is a phone featuring mediatek mtk6752. It was all good but I decided to restore factory settings and phone seems to be bricked. I have watched many tutorials and read guides but nothing helps. My phone blinks with android logo continuosly, once per few seconds it displays android with red exclamation mark inside of his body. I have tried to do recovery but phone only resets showing Jiayu logo or turns off completely. Obviously I have tried to flash stock rom but my phone is not recognized by the PC, and no held buttons combination helps. It does recognize it with the battery in but I can't flash with it in, right? I have tried removing mediatek usb drivers, redownloading them, flashing stock rom by different programs, but the phone is just not recognized. I have read something about hard reset (which includes working with the hardware) but I hope there is another non invasive solution.
Click to expand...
Click to collapse
Does you've fixed this issues?
are you using windows 8 ? if you are u need to set the windows to allow unsigned drivers and install the mtk drivers. Then using spflashtool flash your new rom
all the files and the tutorial are available @ needrom.com under "S3S (Advanced)" by sorix
guys i have softbricked my lenovo a6000 and its stucked on lenovo logo
i have tried adb method to flash back recovery mode but when i rum commands it gives error == device null found
when i connect my device to pc it makes an connected sound help me out of this as this is the only mobile i was having
plzzzzzzzzzz guyzzhelp me out
Bro need help I installed twrp and then cm 13 on my a6000 and by mistake I deleted backup of my stock kk rom and now when I try to go in download mode, recovery it doesn't open it show only Lenovo logo . By mistake I flashed a6000+ stock recovery and after that when I try to flash stock recovery of a6000 using adb nothing open .. so now nothing download mode or recovery mode is opening but i still boot into cm13 how solve it to revert back to kk ?
Solution
Shubhamraaj said:
guys i have softbricked my lenovo a6000 and its stucked on lenovo logo
i have tried adb method to flash back recovery mode but when i rum commands it gives error == device null found
when i connect my device to pc it makes an connected sound help me out of this as this is the only mobile i was having
plzzzzzzzzzz guyzzhelp me out
Click to expand...
Click to collapse
I had also stuck in boot logo once in a custum ROM .
but i fixed it : steps .
Download twrp recovery in your pc. ( rename it as twrp.img ) ,
Boot your phone in to fastboot mode .,
Make sure ur pc has ADB drivers ,
Once , phone get into fastboot mode ,
Type this Commands : 1)fastboot devices ( to check if ur phone is getting detected or not , if it shows no device found , check connection )
2) fastboot flash recovery twrp.img ( to flash recovery)
3) fastboot reboot recovery ( to boot into recovery )
4) download any ROM to SD card and flash it from recovery.
Hit thanks button if this helped you.
Hello guys I have a6000 (Lenovo)
But my problem I saw this video
. Which is easy to revert back to kk rom but I have installed twrp which is not useful for above video method .so when I try to to install Philly or cwm which is used in above video it not installing only twrp will installing other custom recoveries not installing so please help me!!! If anybody have the twrp backup of stock kk rom of a6000 please send me!!
My lenovo a6000 also got stock on boot logo in a custom rom. Its now in no use. Now when i try to connect ut to my pc, its only charging. My device is not being connected to pc. Now what to do ??
Androidsabya said:
My lenovo a6000 also got stock on boot logo in a custom rom. Its now in no use. Now when i try to connect ut to my pc, its only charging. My device is not being connected to pc. Now what to do ??
Click to expand...
Click to collapse
FOLLOW THIS
Need help
sasukay said:
FOLLOW THIS
Click to expand...
Click to collapse
Actually 1st i did root my lenovo a6000. Then i was trying to install cyanogen rom through sd card. But it showed e verification failed. And while booting it gets stock showing cyanogen logo. I tried my phone to connect to pc, but it only charges my phone but doesn't show up in connected device in my laptop. I went to an mobile repair shop, bcoz i thought may be i was missing something. But after visiting 3 repair shops, they also couldn't solve my problem. Now how can i get my mobile to back condition ? Need help. If anyone can help plz give quick rply. But i need to talk to someone who can help regarding this issue. So if you can talk to me, plz call me 7008678740. Thank. Plz give response.
New problem arrised
sasukay said:
FOLLOW THIS
Click to expand...
Click to collapse
I could successfully restored my lenovo a6000 kitkat rom. But a new problem arrised. When i try to power on, it just starts for 2 seconds and vanishes immediately just showing the lenovo logo. Again n again it just being on and off. When i put this battery in another a6000 plus mobile, the same problem occurs. I mean , i want to know why is this happening ? Is the battery gone !!!
Androidsabya said:
I could successfully restored my lenovo a6000 kitkat rom. But a new problem arrised. When i try to power on, it just starts for 2 seconds and vanishes immediately just showing the lenovo logo. Again n again it just being on and off. When i put this battery in another a6000 plus mobile, the same problem occurs. I mean , i want to know why is this happening ? Is the battery gone !!!
Click to expand...
Click to collapse
On first look, it seems like your phone is in bootloop and you need to flash new ROM after wiping the partitions correctly. But, then you are saying that same thing is happening when you insert this battery in another A6000. I think your battery has gone rogue due to some virus, just throw it away. Jokes apart, if another device is showing same behaviour then its almost 100% sure, that your battery has issues and need to be replaced. And, why don't you actually check switching on your phone by putting the battery from that another A6000 into your A6000.
I have checked with another battery, my phone works fine. But that particular battery is doing only on off continuously. But #important thing is , i don't think the battery has gone. Bcoz during the on off process, if i press volume down key, it shows lenovo logo and gets stock there. If the battery has problem, then how can be it stays on showing the logo ?? Confused ???
hey guys today I am here to help you with your hard bricked beloved yu .when I got my device bricked(you yureka plus) I searched almost every corner on web to rectify the problem but every where I found words like"yu yureka hard bricked but can be detected by windows as Qualcomm hsb bulk ,fake guides on you tube some other guides which do not match peoples consequences
ANALYISING THE PROBLEM
this guide will work if you found following characteristics in your dead yu
1)its not detected in windows weather you put the PC on test or install the Qualcomm drivers
2)only a red led near the recover glow when you connect it to a power source
RECTIFYING YOUR PROBLEM
okay let's start first make a backup emmc image for yu which will send it to fastboot mode
fetch a memory card of 16gb format it in fat32 now using a IMG writing tool (I used win32 disk manager)write the emmc image on it(will take around 20mins)
I know some people has resource deficiency(like me) but get your yu's battery charged at least 40% now unscrew your you on the main board you will see six golden points now insert battery connect data cable to PC and phone(I had assumed here you have installed yu latest drivers in PC) you will see the red led glows again now press the vol up button and short the 2and 6 points on the main board (by a copper wire)pressing the power button
you will several colored lines come on screen and your device will connect as a verified USB device this is the fastboot mode in yu
Now the real works starts as some people still has locked bootloader I here use the official cyanogen as only stock ROM will automatically boot the device now download the requested files I had given the link viz official firmware for yu
The firmware zip contains ygdp tool open it(password 369) fill the CPB file click on start and done on the first boot several lines will appear they will vanish after you warm up your yu by playing games:laugh:
All credits for ygdp assembly tools goes to the coolpad corporation ,Android mtk for firmware files again coolpad for general coolpad drivers
sorry if you found a little tedious here its my first post by my revived you
Mind a little financial help
paytm no 7404034359(Rs 50 or 20 whatever you like)
Help.....
I have done the above steps and and the flashing of stock firmware is done successfully, but when i turn on the phone it always shows low battery. Is there a problem with my battery or Motherboard?
i had a friend's yureka with bootloop on YU logo,i flashed it using adb fastboot,the phone started vibrating and dint even turned on,only goes to fastboot mode after long pressing volume up and shows red light on connection.I also tried emmc image burning on sd card method but still in same condition.Please help
ygdp tool reference
iamtj said:
i had a friend's yureka with bootloop on YU logo,i flashed it using adb fastboot,the phone started vibrating and dint even turned on,only goes to fastboot mode after long pressing volume up and shows red light on connection.I also tried emmc image burning on sd card method but still in same condition.Please help
Click to expand...
Click to collapse
Bro try flashing stock ROM go to android mtk download from there drivers as well as rom
may be bad battery
davidchellappah said:
I have done the above steps and and the flashing of stock firmware is done successfully, but when i turn on the phone it always shows low battery. Is there a problem with my battery or Motherboard?
Click to expand...
Click to collapse
Bro after flashing stock ROM do it rebooted it self?
It worked dude...million thanks to you!!! Since i burned those emmc image to my brand new sandisk 16gb sd card...it is not formatting nor showing the correct size.. Nothing.... so can you tell me how to use the sd card normally again with detailed and 100%working steps. Thanks in advance!!!!
Harish Topgi said:
It worked dude...million thanks to you!!! Since i burned those emmc image to my brand new sandisk 16gb sd card...it is not formatting nor showing the correct size.. Nothing.... so can you tell me how to use the sd card normally again with detailed and 100%working steps. Thanks in advance!!!!
Click to expand...
Click to collapse
well you see the memory card used by me belonged to
one of my friend and i returned him as it is with image file
written on it. when i asked him how he got it normal he said that he put it in a net setter dongle and formatted by going in disk management but i think a simple card reader will do the job for you
Mosam panghal said:
well you see the memory card used by me belonged to
one of my friend and i returned him as it is with image file
written on it. when i asked him how he got it normal he said that he put it in a net setter dongle and formatted by going in disk management but i think a simple card reader will do the job for you
Click to expand...
Click to collapse
Yeah.. Formatting didn't seem to work so spending some time on internet I repartitioned the memory card using a software and I'm good to go now!!
Hello,
My Device is Lenovo A6000 Plus (2GB+16GB). My Device doesn't get charge. Once I change its Power IC as it was damaged. After that my Device was stucking on Lenovo Logo. Shopkeeper told me there is need to put software. Well at that time I didn't did. Now when I connect To Qfil & flash the firmware file it gives error that Firehorse not install. File is corrupted.
Can anyone give the solution on this?
I want my Device working again as I want to root & flash Pie ROM.
our problem is the same
So yeah, I screw up by a lot, but let's see if someone can help me/
I tried to update twrp on my phone and it got bricked, ADB was not seeing the device but Mi FlashTool was with a code but not COM, tried changing the phone drivers brom 900E to QL8000 and it got registered by MiFlashtool as COM and another code, the phone was still showing there even if I could not make the phone go to fastboot mode, just blackscreen; I tried to reinstall stock rom with it but got stuck at "flashing", disconnected the phone, the phone was still bricked in a black screen, when trying to reconnect the phone again to the pc, Win10 now displays an error
https://imgur.com/a/VS1yh6t
,
https://imgur.com/a/4PxUD7E
, I already tried uninstalling the device, deleting and reinstalling the drivers (unable because for some reason they won't appear now, but already tried installing the from their 1st party and prom MiFlashTool), so the phone won't turn on, display anything, go into recovery/fastboot, and I don't know what to do now, is the phone lost? I hope you can help me with this issue.
Hello Bro. Try install latest Mi Flash Tool latest version and then install the drivers. For my it's works in windows 10.