X Compact bricked. Not recognized by pc. - Sony Xperia X Compact Questions & Answers

Hello all,
i have big problem with my x compact phone.
I used the amazon music app suddenly the phone was freezed. So i restarted it. After that the phone was in a boot loop. Message:"Your phone is corrupt...".
This wasn´t stopable even with hard reset (power+volume up). So tried my luck with a software repair using xperia companion. Nearly at the end of the process it stopped with the message "failed please try again.." . After that the phone wasn´t able to get in flash mode (blue light). The pc doesn´t recognize it. Windows says usb failure. From time to time the red light is blinking when i connect it to the charger thats all. No other response.
Is there a chance to repair it? Please help me.

If fastboot mode isn't available, your only option is to get the phone in 'service mode':
- turn phone off
- hold <volume down> button
- while holding <volume down> button, connect usb cable to pc and phone (led should turn green).
In this mode you can try to flash the phone with Emma:
https://developer.sony.com/file/download/flash-tool-for-xperia-devices/
or alternatively FlashTool:
http://www.flashtool.net/downloads.php
If you can't get into 'service mode', check on another pc with another usb cable (and make sure you install the usb drivers correctly). If that also doesn't get you into 'service mode' the phone is destined for RMA.

Thank you. But can´t get into service mode. When i try the led blinks red.
I´m not sure if the drivers are correctly installed. When i download them from sony, i installed them as legacy hardware but it have the status "not working".
How can i install them?

I think even without drivers installed the phone should go into service mode if you follow the aforementioned steps (only then it shows up in Windows device manager as an unknown device), so that sounds bad. You should try with another pc and another usb (data)cable.
I don't use Windows myself so I can't help you with driver installation, but I gather if Sony provides drivers it should be an easy 1-click installation. Maybe someone else can chime in on that.

TotalNew said:
Thank you. But can´t get into service mode. When i try the led blinks red.
I´m not sure if the drivers are correctly installed. When i download them from sony, i installed them as legacy hardware but it have the status "not working".
How can i install them?
Click to expand...
Click to collapse
By installing Xperia Companion on your PC or Mac you should have any drivers that might be needed. So if you cannot successfully connect to your computer in any mode, then it seems likely that you'll have to send it in for repair. Edit: But do try another cable first, as was suggested.

Related

[Q] Xperia Play Update Problems

Hi,
looked for an answer to this problem in the forum but didn't find it, i have a stock xperia play, sim free running gingerbread 2.3.2 and i'm based in the uk and have a uk handset. My problem is although i am offered the 2.3.3 update, when i try to get it i get stuck at the preparing phone stage on pc companion software, the phone switches off then the software tells me to disconnect USB cable from pc and phone, then it tells me to check battery power level(phone is off?) is at least 50% (it is 80%)then says turn the phone off? leave for 5 seconds then plug back in whilst holding the back hardware button. After this the computer does 3 beeps (normally error noise) and i have to do this all again, don't see anyone else having problems updating? your help would be greatly appreciated.
Use SUSE! Should work just fine.
USe another computer if it doesn't work
and yes try http://www.sonyericsson.com/cws/sup...etailed/updateservice/xperia-play?cc=gb&lc=en
Before asking for help
i have narrowed it down to the computer not recognising the phone when it is off(blue light mode) i looked at device manager, says there is no driver for S1boot fastboot?
driver are on program files > sony ericsson > pc companion > driver 32/64bit
check there and install them manually
or check the pc companion in sony ericsson menu on your phone and connect your phone and press install
then install pc companion and let it do his work installing the driver.
check my mtpapp thread if you need more detail
don't clear mtpapp (your apps should be ok btw)
Tried everything now, still nothing happens after i plug in usb cable whilst holding the back button, what is actually supposed to happen after this point, i get the blue light, nothing else.
rojach said:
Tried everything now, still nothing happens after i plug in usb cable whilst holding the back button, what is actually supposed to happen after this point, i get the blue light, nothing else.
Click to expand...
Click to collapse
When the light goes blue, you are connected in either bootloader or recovery mode. If your device is not detected, go to device manager and install the drivers manually
Sorry double post
Are you connecting the phone via a USB hub?
If you have many usb ports on your pc being used, try to disconnect a few and plug the phone directly to your pc.
I had this same issue and it happened because my stupid logitech keyboard keeps messing with my usb drivers everytime i plug in a new USB device.
I unplugged the keyboard and the update went swiftly.
In order to enter flash mode, you ought to:
1)switch off the phone
2)remove the SIM card and sdcard (this is mandatory!),
3)remove the battery for 5 seconds, then put it on.
4)hold the Back button while you connect the device.
The device will shine with a green light. The blue light is used for the Fastboot mode, and you get that light if you:
1) Switch off the device
2) Hold the Search button (the magnifying glass one)
3) connect the device to the USB cable.
Hi all, thanks for your help but still no luck, i have tried all of the above on 2 computers, the same problem occurs, not sure what is supposed to happen when i plug the USB into the phone whilst holding the back button during update? all i get is a blue light on the phones power button. Nothing appears on the pc either??? i have done a full factory reset and tried installing drivers, is there a specific driver for entering the recovery mode on xperia play?
Sony Update Issues
http://unlockbootloader.sonyericsson.com/instructions
Note: We have seen in some forums that customers unlocking the boot loader on their phones have experienced problems when they accept a FOTA (Firmware upgrade Over The Air) update. The issue has been reproduced and we are working on a solution. For customers that have unlocked the boot loader please do not accept the Firmware upgrade OTA.

[Q] USB composite device driver not found

Hay,
i tried to reset my X2 and ih stoped at half of the customizing proces. It stayed that way all nigt. Than I hard reseted it again. Now when I try to turn it on is stops at sony ericsson logo. I tried to pres volume down button together with power button and it worked! White screen with SE logo. Folowing instructions from SE PC Companion repair proces, I conected it with PC, and than regognition of new device started. Message apeared "USB composite device driver not found" and PC companion couldn't find/repair it because device was not installed properly. I tried it on 4 diferent PC's, with diferent windows, with latest software and drivers. Any idea what to do? And how can i find SEUS to instal it? I know that there is similar treads but not for this phone. Bad english, sorry.
solved
SEUS found, phone recognised. Yey!
unsuccesful
The Update was unsuccesful! F! What now?
idea? anyone?
hi everyone
I'm facing the same problem, my computer can't identify x2 when I connect it "windows 7 ultimate 32 bit"
it gave me unknown device when I opened the device manager and windows update can't find the device drivers.
what should I do to let it recognize my device in order to complete the update
by the way , my phone is not usable now , it is just hang on windows logo when I switch it on and removing the battery the only way to switch it off
I really need your help guys, I have been trying SEUS for more than week

[Q] Defy not able to connect to my PC via USB

i CAN't connect it with my pc and rsd lite can't detect my phone when i plugged it in!
also, i can't charge it via PC nor the power supply(i have tried using moto's one and a unofficial power supply)
but the most wired thing is i can charge it via an"portable battery"
maybe it is an hardware problem and i can't flash back to my official sbf
warranty is now void?
or can i flash a SBF without connect to PC?
give me a now hope plz
Have you tried the boot loader mode (forum.xda-developers.com/wiki/index.php?title=Motorola_Defy):
---------------------------------
How to get rsdlite to recognise a phone that won't boot
You flashed, something happened, now screen is black, phone doesn't react, u are in a boot loop, rsdlite cant recognize the phone. you're right here.
To get RSDLIte to recognize your phone you have to enter boot loader mode. this means press VOL-UP + POWER If nothing helps, try pushing VOL UP before!' you put the battery in (RSDLIte should be running and awaiting a new connection at that time) If you are using Windows 7, try seting RSDLite to "compatibility mode: Windows XP SP3".
i have tested the connection in bootmenu and RSDLITE not able to recognize my phone
any ideas?
Hello
Please somebody help me. My notebook doesn't recognise my DEFY via USB. More details: When I got the phone it worked but after a while not always. Sometimes it connected 5 minutes later but nowadays doesn't work at all. By the power charger it's charging normally.
When it's plugged to the computer, the phone's screen lights up, but doesn't connect or charge. If I tick on/off meanwhile the USB debug, the USB sign shows up but it's still not charging or connecting. (I've already tried all 4 options)
Moreover when I remove the USB cable, the USB signal doesn't disappear until I restart the phone or abort the USB in the application manager.
I've already tried to install or uninstall the driver (Moto Helper) but didn't help.
The main problem is that if I connect the phone to the notebook, the device manager doesn't see it. (I tried different computers, Win XP and Win 7)
I did a factory reset several times but nothing happened.
I think there was an automatic software update and maybe the problem started at this time.
This is my first Android phone and I'm not an expert so I really need your help.
I wanted to install a new ROM but the RSD lite doesn't see the phone neither in Bootloader mode. It says: "Connect USB Data Cable" and when I connect it says: "USB" so recognises something.
I'm trying to fix it for weeks but I can't find to solution.
System version: 34.177.3.MB525.Retail.en.GB
Build no: JOREM_U3_3.4.2_177-3
Win7 x64
Sorry about my English and thank you for your help.
I didn't mean bootmenu tommy, BOOTLOADER MODDE: press VOL-UP + POWER, try pushing VOL UP before! to get RSDLIte to recognize your phone(RSDLIte should be running and awaiting a new connection at that time)
---------- Post added at 09:52 PM ---------- Previous post was at 09:42 PM ----------
Hey poross, I guess that your problem seems like a virus activity or maybe a faulty USB cable. Try another USB cable and another PC (with a good antivirus running, indeed!). Before connecting to the new PC, reset your defy...
I just hope it helps. If not, maybe your defy has a hardware problem...
If you are using windows 7 make sure that you installed good drivers for system x86/x64. I'm using RSD on Windows 7 X64 and I have no problems with it. Check in device manager for some unknown devices after plug phone to USB. If system wont see any new device after plugging it wont be driver problem but something wrong with phone, usb cable or usb port. Even if driver fails system should see the phone like unknown device or something.
MMarv said:
I didn't mean bootmenu tommy, BOOTLOADER MODDE: press VOL-UP + POWER, try pushing VOL UP before! to get RSDLIte to recognize your phone(RSDLIte should be running and awaiting a new connection at that time)
---------- Post added at 09:52 PM ---------- Previous post was at 09:42 PM ----------
Hey poross, I guess that your problem seems like a virus activity or maybe a faulty USB cable. Try another USB cable and another PC (with a good antivirus running, indeed!). Before connecting to the new PC, reset your defy...
I just hope it helps. If not, maybe your defy has a hardware problem...
Click to expand...
Click to collapse
actually,i am in bootloader(versoin 9.10) and rsdlite still not able to detect my phone =..=
but i notice that when i plugged it in,the phone showed "transfer mode USB"
but nothing happened in rsdlite,no info of device properties.....
what the hell.....
To tommy:
Let's make a conclusion:
1-You have the correct drivers but RSDLite doesn't recognize your phone even in the bootloader mode
2-The charger can't charge your battery
3-The portable battery CAN charge it! (So the phone connector has no problem)
So: It is most likely that you've got a faulty usb cable
Thanks for dealing with my problem
Chamelleon: The device manager doesn't see anything while the cable is plugged but the phone detects something -probably the USB power- but doesn't connect at all. It happpens in the bootloader mode as well so detects the USB cable but it seems that the phone doesn't send sign to the computer. I haven't had any problem with USB detection, connection (except this phone) for a long time.
MMarv: You mean there's a virus on the phone? if it's the situation, installing a virusbuster to the phone could solve it? Which one is a good prog?
I tried with 3 different cables and still not working. With the wall plug charger and the car's USB socket are ok but none of them charges from the notebook.
poross said:
Thanks for dealing with my problem
Chamelleon: The device manager doesn't see anything while the cable is plugged but the phone detects something -probably the USB power- but doesn't connect at all. It happpens in the bootloader mode as well so detects the USB cable but it seems that the phone doesn't send sign to the computer. I haven't had any problem with USB detection, connection (except this phone) for a long time.
MMarv: You mean there's a virus on the phone? if it's the situation, installing a virusbuster to the phone could solve it? Which one is a good prog?
Click to expand...
Click to collapse
I mean Virus on your laptop. Hard reset your phone and try another PC with a good anti-virus installed!
So if cable is ok, usb port in pc and phone is ok it must be driver problem. Delete all what appears as Motorola driver including drivers from system32 and then install it again. You can also try to install it on different PC with 32 bit system. Do not install any unknown drivers, just install Motorola Media Link or Motorola Software Update cause if you have this one and some different it can be problem. Or you just have something wrong with system. First try on different pc with drivers from MML or MSU.
Succeeded.
The solution was incredibly simple. It was strange when I did a factory reset (4 times) and rebooted the phone it restored my acccounts, shortcuts, settings. I ticked off two things: settings/Privacy/Back up my data and Automatic restore. Then took out battery then I put it back and began the reset. After it the phone forgot really everything of my details and now the USB is working perfectly.
MMarv said:
To tommy:
Let's make a conclusion:
1-You have the correct drivers but RSDLite doesn't recognize your phone even in the bootloader mode
2-The charger can't charge your battery
3-The portable battery CAN charge it! (So the phone connector has no problem)
So: It is most likely that you've got a faulty usb cable
Click to expand...
Click to collapse
i tried another usb cable,but it still not able to connect.....
poross said:
Succeeded.
The solution was incredibly simple. It was strange when I did a factory reset (4 times) and rebooted the phone it restored my acccounts, shortcuts, settings. I ticked off two things: settings/Privacy/Back up my data and Automatic restore. Then took out battery then I put it back and began the reset. After it the phone forgot really everything of my details and now the USB is working perfectly.
Click to expand...
Click to collapse
not working for me =..=
however,i have 2ndinit installed
and after factory reset,the phone is still rooted and 2ndinit still here
so will it cause any problem?
Hey Tommy,
I nearly bricked my defy, and the battery was low too. RSDite not able to recognize it. It seemed that charger can't charge the battery either. But I was wrong. The charger was actually charging the battery. I removed the back cover with the charger connected and the battery in place. I tested the two outer connectors of the battery with a voltmeter (when the battery is in place, they are slightly exposed). Initially the voltage was about 3 volts and steadily increased... Test it if you can. If it is not charging, I bet that it is a phone connector problem. You should return it and I think they can repair it easily...
Hi Tommy1994
First I'm not an expert, this is my first android phone.
My probelm was (I think) an android error. I made factory reset 4 times but it always restored my details. (It's not a perfect FR). After it I did a bit different FR:
-1. in the normal android/ settings menu/Privacy/Back up my data -thick off. So it won't make any backup
-2. swich off the phone
-3. take the battery out for 30sec then put back
-4. press the volume down and hold it while you press the power on button but hold the volume down for more 4 sec. you will see an android robot with an exclamation mark.
-5. press the volume up and down together that's how you enter to the Recovery menu.
-6. first chose the "Wipe cache partition" (you can move with the volume buttons and select with the power button) -wait till "Cache wipe complete"
-7. then chose the "Wipe data/factory reset" - wait till "Data wipe complete"
-8. after these chose the "Reboot system now"
-9. if your phone doesn't want to start just get the battery out for 30sec and take back.
note: you will lose everything of your personal details, installed apps...
note2: it's my FROYO's (android 2.2.2) menu probably yours is different
Sorry for my English, hope you understand though.
hope this helps
If your are trying to connect on windows vista or 7 I think you must be loged on as admin of the computer. I had same problem but when I used windows XP it worked fine this is for rsd lite
going to try ,i really hope it will help
thx
i have flashed cm7 and still not able to connect it to PC
i am quite sure it is not software problem, maybe it is about the USB cable?
is that possible the USB cable can charge but not able to transfer data?
hi tommy1994 ,
i'm having the same problem as you, when i'm in the bootloader screen the rds lite program don't find my defy...
have you found any solution?
Thank you very much

[Q] Gionee E7 (32GB) got bricked

I tried to downgrade from Kitkat to JB via flashtool this morning which I often successfully flashed with the same method. But while the flashing is going on and almost finish the flashing (system.img, userdata.img, etc. are already flashed), there seems to be some problem and popped out that the flashing is fail. And then the device does not boot up. While I tried to reconnect the device to PC, the PC cannot recognize the device as shown in the picture. Unable to process any further method. Does anyone in this forum knows how to recover the bricked device like this?
The phone starts? In a black screen?
If the PC detects it like that the phone has some energy and connection...
Does anything apears on the screen? Can you go to the Recovery Mod?
Have you tried to force the driver installation on that USB item that appears on device manager?
Do you have access via ADB or fastboot?
Did you nottest in what partition did the error message appeared?
Please provide some answers to these questions so i can try to help you...
RSGI_PT said:
The phone starts? In a black screen?
If the PC detects it like that the phone has some energy and connection...
9Does anything apears on the screen? Can you go to the Recovery Mod?
Have you tried to force the driver installation on that USB item that appears on device manager?
Do you have access via ADB or fastboot?
Did you nottest in what partition did the error message appeared?
Please provide some answers to these questions so i can try to help you...
Click to expand...
Click to collapse
Nothing on the screen. Not able to boot into recovery or adb is not working. The phone is just death. But, when I insert the usb cable, the pc can detect it. I even approach the Customer Care here in Aizawl, but they cannot fixed. Even when I followed the instruction as per one xda member posted here, The qualcom hs - 9006/8 is displayed on the device manager and when I tried to flashed it with emergency mode, the result always the same. FAILS
hruaiapunte said:
Nothing on the screen. Not able to boot into recovery or adb is not working. The phone is just death. But, when I insert the usb cable, the pc can detect it. I even approach the Customer Care here in Aizawl, but they cannot fixed. Even when I followed the instruction as per one xda member posted here, The qualcom hs - 9006/8 is displayed on the device manager and when I tried to flashed it with emergency mode, the result always the same. FAILS
Click to expand...
Click to collapse
Try this:
- Start GNQC with the phone disconnected
- Connect the Phone and see GNQC recognizes the QLoader
- If so, press power button until the phone vibrates
- Wait for the GNQC recognizes again the QLoader and press Download on Emergency Mode
Use this KIKAT ROM: https://docs.google.com/uc?id=0B8H5JoBDpTnJMGE2QTJPR0FWX0E
This worked for me, i had the phone completly died, not even recognized by the PC, waited a day and tried again.
Once the QLoader is recognized your good to go!!
I'm having another problem after that, now theres no GSM/3G signals....
I need a EFS backup with the TWRP recovery.... No one seems to have
RSGI_PT said:
Try this:
- Start GNQC with the phone disconnected
- Connect the Phone and see GNQC recognizes the QLoader
- If so, press power button until the phone vibrates
- Wait for the GNQC recognizes again the QLoader and press Download on Emergency Mode
Use this KIKAT ROM: https://docs.google.com/uc?id=0B8H5JoBDpTnJMGE2QTJPR0FWX0E
This worked for me, i had the phone completly died, not even recognized by the PC, waited a day and tried again.
Once the QLoader is recognized your good to go!!
I'm having another problem after that, now theres no GSM/3G signals....
I need a EFS backup with the TWRP recovery.... No one seems to have
Click to expand...
Click to collapse
my e7 died. you are stuck using flash tools. is not even recognized by most PCs. maybe it drain? I can do? help me
I have the same problem, screen is completely black after trying to instal newer official rom. When I connect it to PC, it detects "hid device". I tried power + volume buttons combinations, but nothing changes. Sometimes notification led turn red for a few seconds but nothing else. And once win xp randomly detected phone as that "q..." thing, but it doesn't anymore. What else can I do?
Can anyone help me? I tried everything and my phone is still hardbricked.
Hello guys
Today i received my E7 and i tried to update via the tool unfortunately something went wrong and now i cant open it nor fastboot or recovery. Some hours ago i tried to connect via usb and appeared on the GNQC but later it showed as unknow device. It was my first day with the phone. Right when i connect /disconnect the usb i can hear the sound but i cant do anything. Is it dead or i can revive it somehow?
It was the first day:crying::crying:
Reinstall the drivesbob the PC, press 30 secs on the power button than connect the phone to the PC. If appears a QLoader port use emergency download on gnqc 1.6.9.0
RSGI said:
Reinstall the drivesbob the PC, press 30 secs on the power button than connect the phone to the PC. If appears a QLoader port use emergency download on gnqc 1.6.9.0
Click to expand...
Click to collapse
PLZ HELP i try to update using this http://www.needrom.com/download/gionee-elife-e7-32g/comment-page-2/#comment-165291 but now my phone doest enen boot or fast boot or anything.. in the proces it said "firehose ping phone fail" and stopped updating since then my phone isnt booting or anything and my pc dont recognize it any more.. plz help
---------- Post added at 15:32 ---------- Previous post was at 15:29 ----------
RSGI_PT said:
The phone starts? In a black screen?
If the PC detects it like that the phone has some energy and connection...
Does anything apears on the screen? Can you go to the Recovery Mod?
Have you tried to force the driver installation on that USB item that appears on device manager?
Do you have access via ADB or fastboot?
Did you nottest in what partition did the error message appeared?
Please provide some answers to these questions so i can try to help you...
Click to expand...
Click to collapse
plz help...
PLZ HELP i try to update using this http://www.needrom.com/download/gion...comment-165291 but now my phone doest enen boot or fast boot or anything.. in the proces it said "firehose ping phone fail" and stopped updating since then my phone isnt booting or anything and my pc dont recognize it any more.. plz help
thianpa he thil hi i solve thei toh m

Bricked Jiayu S3 Advanced help!

Yesterday i flashed my Jiayu S3 to lolipop (i tought) and i just bricked my phone!
After reboot it was just dead.. when i plug into pc with USB i hear the connect sound and after 2 seconds the disconnect sound. This keeps on going until i pull the USB plug. When i look in DeviceManager i see it refresh after every sound, but nothing pops up (unknown device or whatever). I deletet all usb drivers with usbdeview, restart pc but still no changes.
I tried with or without battery, but without it does nothing at all.. i tried holding Vol+ or - or both or with power button, but nothing.
Read some threads about unbrick and install correct usb driver for jiayu s3, but all the options they came with does not work on my device!
I'm a little despered now and don't know what to do.. i get the feeling that my 2 weeks old phone is dead? :'(
My pc has windows 7
Did the flash with SP Flashtool 5.1516
Did not untick preload in flashtool, i guess i got the wrong preload or something??
Please help!
No one..? :crying:
Lowrida said:
Yesterday i flashed my Jiayu S3 to lolipop (i tought) and i just bricked my phone!
After reboot it was just dead.. when i plug into pc with USB i hear the connect sound and after 2 seconds the disconnect sound. This keeps on going until i pull the USB plug. When i look in DeviceManager i see it refresh after every sound, but nothing pops up (unknown device or whatever). I deletet all usb drivers with usbdeview, restart pc but still no changes.
I tried with or without battery, but without it does nothing at all.. i tried holding Vol+ or - or both or with power button, but nothing.
Read some threads about unbrick and install correct usb driver for jiayu s3, but all the options they came with does not work on my device!
I'm a little despered now and don't know what to do.. i get the feeling that my 2 weeks old phone is dead? :'(
My pc has windows 7
Did the flash with SP Flashtool 5.1516
Did not untick preload in flashtool, i guess i got the wrong preload or something??
Please help!
Click to expand...
Click to collapse
so you cannot boot into recovery or fastboot either?
Lowrida said:
Yesterday i flashed my Jiayu S3 to lolipop (i tought) and i just bricked my phone!
After reboot it was just dead.. when i plug into pc with USB i hear the connect sound and after 2 seconds the disconnect sound. This keeps on going until i pull the USB plug. When i look in DeviceManager i see it refresh after every sound, but nothing pops up (unknown device or whatever). I deletet all usb drivers with usbdeview, restart pc but still no changes.
I tried with or without battery, but without it does nothing at all.. i tried holding Vol+ or - or both or with power button, but nothing.
Read some threads about unbrick and install correct usb driver for jiayu s3, but all the options they came with does not work on my device!
I'm a little despered now and don't know what to do.. i get the feeling that my 2 weeks old phone is dead? :'(
My pc has windows 7
Did the flash with SP Flashtool 5.1516
Did not untick preload in flashtool, i guess i got the wrong preload or something??
Please help!
Click to expand...
Click to collapse
Just flash it again, but this time with "Firmware upgrade " in SP Flashtool instead of "Download". Change from KK to LL needs reepartitioning, so firmware upgrade.
The reason why you don´t "see" the S3 any longer on the pc is, that the USB storage mode from KK, which is driverless for windows, don´t work right now on LL.
Once flashed to LL you will need to install a driver, for windows to connect to the S3.
@ Dior DNA:
No i can't. Phone does nothing with the buttons. Only diference if i hold Vol - then time from connect sound and disconnect sound is a little longer.. about 10 seconds. But still nothing happens.
@1testi:
Flashtools can't see my phone. I tried it a hundred times. With battery, without battery, with Vol - and with Vol +.
When i connect the USB cable i hear the connect sound and after 2 a 3 seconds i hear disconnect sound. This goes on and on until i pull the USB cable out. In devicemanager i see a refresh going on, but nothing pops up.
I'm realy despered on what to do now?
Lowrida said:
@1testi:
Flashtools can't see my phone. I tried it a hundred times. With battery, without battery, with Vol - and with Vol +.
When i connect the USB cable i hear the connect sound and after 2 a 3 seconds i hear disconnect sound. This goes on and on until i pull the USB cable out. In devicemanager i see a refresh going on, but nothing pops up.
I'm realy despered on what to do now?
Click to expand...
Click to collapse
Why the SP Flashtool isn´t working any longer? You didn´t deinstalled the driver, did you? Just try to flash again with "Firmware Upgrade".
I don´t know a way to reinstall the driver in windows without the preloader. The only thing you can do, as far as i know, is to use a linux
pc to flash again. Linux don´t need a driver for SPF, only some rules.
Lowrida said:
@ Dior DNA:
No i can't. Phone does nothing with the buttons. Only diference if i hold Vol - then time from connect sound and disconnect sound is a little longer.. about 10 seconds. But still nothing happens.
(
Click to expand...
Click to collapse
Booting into recovery or flashtool I meant regardless of pc and/or spflashtool.
If I recall correctly:
hold volup and power boots recovery
hold voldn and power boots flashtool
If you can boot recovery then which one is it? Maybe you can restore something or manually flash preloader bin from there.
After the flash i reboot and then the connect and disconnect sound appears. So i tried differend things, but could not connect. I wanted to flash again, but flashtool did not reconice the phone and nothing in DeviceManager. That's why i thought to remove the driver and try to re-install it. But that did not help..
Holding Vol - or + button with power button or both Vol buttons with power button does nothing.. i tried to hold all combinations at least 30 seconds, but nothing at all.
I have no Linux pc or any knowhow to make a Linux pc.. or a pc to install Linux on..
One last thing you can try: remove the battery, wait a little, insert the battery again. Hold vol+ key, keep holding it and press power
button, while still holding the vol+. If you don´t see anything happening then you bricked the phone.
You will need help from a professional or at least from someone with a linux machine, sorry.
I'll try that.
You have any idea what could have caused the brick?
As i wrote above, moving from KK to LL with wrong parameter "Download" in SPF.
....and a not working recovery.
You should try this method :
darmowyinternet.net/forum/temat-poradnik-jak-uruchomic-uceglony-telefon-po-wgraniu-zlego-romu-test-point_383
unfortunately you have to translate before
Ok i tried that site with google translate and i could a little make up what they are saying.
But that is a very drastically operation, and i would like to give it some other tries before dismantling my phone.
So i googled and googled.. came here: http://forum.xda-developers.com/showthread.php?t=889128
Had enough electronics lying around from my former 27mc hobby, so searched for the right resistors,
cut up a micro usb cable and give it a try... well.. nothing! Tried for about an hour and gave up.
Then i googled on Unbrick Jigs, but for what i read they are only for Samsung phones, so i gues the trick
with the resistors were also?
So googling again... came here: http://forum.xda-developers.com/showthread.php?t=2454004
Reading the tread and the comments, someone mentioned a download for "Mediatek Driver Auto Installer".
Downloaded that and installed the drivers. Plugged in my phone and... whoohoo!! Something is happening! :silly:
My devicemanager saw an "Alcatel single RNDIS interface". I unplugged and plugged my phone a few times to
be sure it was my phone. Sooo... one step further! :good:
Then i googled on this device.. came up with all sorts of network devices, not helpfull. Then googled on Jiayu with
this device. Came up with this tread: https://www.china-devices.com/topic...vcomm-drivers-onto-your-pc-win-7vistaxp-only/
It's a tread about bricked Jiayu G3 devices, but i thought, 'What the heck, lets give it a try!'.
I downloaded the "MTK Megapack - All Tools Here!" and unpacked. Wend back to device manager and manually updated the driver
of the Alcatel device. Show all devices - browse - wend to Megapack map and there were MTK drivers for the 65xx device.
And yess.. when i plug in my phone there's the device: " MTK USB Port (COM7) "
SP Flashtools sees my phone again! :good:
Tried to flash a stock preloader, but got an error: "BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) – [EMI] Enable DRAM failed!"
But for now that's a problem for tomorrow.. it's almost 2:30 and i have to got some sleep!
(sorry for the misspellings or telling things not clear, i'm tired and english is not my main language)
Grats!
You can google the error. This leds you in the right direction.
It's alive!!!!!! :laugh::silly::victory:
Because the kitkat stockrom i downloaded gave me the same error over and over i searched for something else.
So i downloaded TF Extreme lolipop 5.1 this morning and give it a try. And all went well. I pulled the usb plug and
pushed power button.. only vibration but nothing. Then pulled the battery and after few seconds put it back in
and try power again. Only 1 vibration.. then tried Vol + and - combinations but nothing. (dammn!)
Then plug the usb in and i saw the battery icon.. it was total empty! (because of a week trying).
So now it's charging and i hope it starts, can't wait!!
Thanx all for the effort in helping me out! :good:
Edit: Ok, so i could not wait and hit power! It shows green screen with Jiayu S3 logo and text "New Load". So i guess it's prepairing for first startup!
my s3 basic is not charging when on.. also when connected to pc thru usb, ipc shows device malfunctioning ,and there is no indication on phone..I try to connect to sp flash tool also no success..same error"usb device not recognized pops up every 2s.everything else is fine..Any method to upgrade to 5.1 now on official kk
Kinda need help, happened something similar
It happened something similar to me.
I flashed the whole ROM, bootloader included, I was very sure that my model, Jiayu S3 3GB ROM + 32GB RAM, was the correct, but still bricked my phone.
There's no problem at all when I plug it into my PC, I installed the lastest MTK drivers on windows 10, having to disable the signature enforcement.
The problem comes when I start flashing. I only mark the bootloader, then I press "Download" (on the lastest version of SP Flash Tools), and plug the phone, with the battery in it (I've tried without battery, pressing all possible combinations and does nothing), when I plug it in with the battery and pressing no buttons, the driver is detected as MTK USB Port. That's a good thing I guess. But It does not pass from the red bar, and gives me the known error "Enable DRAM Failed".
I've tried to google any possible solutions, reinstalling other version of the MTK drivers, on different versions of Windows, with other versions of official ROMs, and the result is always the same.
The only thing that's left to try is flashing it with an Ubuntu machine, which is something I do not expertise to be honest, but I'm gonna gather some info and try to do it.
However, if someone has any idea of what I might be doing wrong (excluding the part when I flashed the bootloader, I'll never do it again), I would be really grateful for any kind of help.
Thank you!
Kiei said:
It happened something similar to me.
I flashed the whole ROM, bootloader included, I was very sure that my model, Jiayu S3 3GB ROM + 32GB RAM, was the correct, but still bricked my phone.
There's no problem at all when I plug it into my PC, I installed the lastest MTK drivers on windows 10, having to disable the signature enforcement.
The problem comes when I start flashing. I only mark the bootloader, then I press "Download" (on the lastest version of SP Flash Tools), and plug the phone, with the battery in it (I've tried without battery, pressing all possible combinations and does nothing), when I plug it in with the battery and pressing no buttons, the driver is detected as MTK USB Port. That's a good thing I guess. But It does not pass from the red bar, and gives me the known error "Enable DRAM Failed".
I've tried to google any possible solutions, reinstalling other version of the MTK drivers, on different versions of Windows, with other versions of official ROMs, and the result is always the same.
The only thing that's left to try is flashing it with an Ubuntu machine, which is something I do not expertise to be honest, but I'm gonna gather some info and try to do it.
However, if someone has any idea of what I might be doing wrong (excluding the part when I flashed the bootloader, I'll never do it again), I would be really grateful for any kind of help.
Thank you!
Click to expand...
Click to collapse
Oeps it might be the same problem with the 32GB version as I have.
See http://forum.xda-developers.com/showpost.php?p=68036678&postcount=295
I am waiting for a stock ROM backup.
I have learned to never flash the original preloader again.
xtyphoon said:
Oeps it might be the same problem with the 32GB version as I have.
See http://forum.xda-developers.com/showpost.php?p=68036678&postcount=295
I am waiting for a stock ROM backup.
I have learned to never flash the original preloader again.
Click to expand...
Click to collapse
You're right, with the 32GB rom version (which is still unavaliable for public use) it worked! I still got it here, so anyone feel free to ask me the link too.
Thanks to xtyphoon and Dior DNA and everyone who made this possible, if you ever come to Girona city, I'll buy you a drink ;D
Kiei said:
[...]if you ever come to Girona city[...]
Click to expand...
Click to collapse
I was around there few weeks ago

Categories

Resources