Hi! After flash my Acer S200 don't start. Just write : Cleen Boot ACER.
If someoane can help me I waitt your sugestion. Thank's very mutch.
surdu_petru said:
Hi! After flash my Acer S200 don't start. Just write : Cleen Boot ACER.
If someoane can help me I waitt your sugestion. Thank's very mutch.
Click to expand...
Click to collapse
What ROM did you flash? sounds like a bad flash... reflash, or try a different ROM
Hello!
Thank's very much, but how can I reflash if the phone dosen't start?
If someoane have the same problem please tell me how can I reflash the phone. Thank's .
surdu_petru said:
Thank's very much, but how can I reflash if the phone dosen't start?
If someoane have the same problem please tell me how can I reflash the phone. Thank's .
Click to expand...
Click to collapse
you didn't break your device , you can reflash it following the flash instructions included , for an example , in rafyvitto's rom's post .Just have a look there .
surdu_petru said:
Thank's very much, but how can I reflash if the phone dosen't start?
If someoane have the same problem please tell me how can I reflash the phone. Thank's .
Click to expand...
Click to collapse
If it dosnt start by camera press button and hold then reset button(this puts device in bootloader mode) if that doesn't place your device in bootloader mode its brick't, thats is if you have the 1.00 radio.
Hi!
rafyvitto said:
If it dosnt start by camera press button and hold then reset button(this puts device in bootloader mode) if that doesn't place your device in bootloader mode its brick't, thats is if you have the 1.00 radio.
Click to expand...
Click to collapse
Thank's Rafyvitto , but I press camera button end hold reset , the phone don't start, just write in black screen with white : S200_3.003b.00_EN
Clean Boot
acer
end don't work , don't start . I waitt 1 hour but the screen dosen't change , it's the same screen like begining. I don't know what I make , maybe I flesh it with a wrong rom , but now if you know ? it's posibile flash again or make something for start , if the phone don't start? Thank's very much....
You can save it, cause the screen that says "clean boot" is the bootloader, so you just need to press the bootloader combination of the 2.00 radio, press power + volume + camera holding all these press reset, if you see a red led blinking then its in bootloader mode, and you can flash your device.
Hi!
rafyvitto said:
You can save it, cause the screen that says "clean boot" is the bootloader, so you just need to press the bootloader combination of the 2.00 radio, press power + volume + camera holding all these press reset, if you see a red led blinking then its in bootloader mode, and you can flash your device.
Click to expand...
Click to collapse
I will try now. Thank's again.
Hi!
rafyvitto said:
You can save it, cause the screen that says "clean boot" is the bootloader, so you just need to press the bootloader combination of the 2.00 radio, press power + volume + camera holding all these press reset, if you see a red led blinking then its in bootloader mode, and you can flash your device.
Click to expand...
Click to collapse
No, my Acer S200 don't want to start reflash, I try exactaly end the red led is blinking but the all the flash rom don't start....just say update failure veryfi the connection USB. I trying with the Acer_EUU haker version 1 end 2. I thing that the phone is dad. Maybe is another solutions? I waitt...Thank's again, very much.
Heelo!
If you know , maybe it 's an solution for boot the rom on the storage card ? I thing , if the phone don't connect with the pc with usb cable is normaly that the flash don't start, maybe if I put the rom on the storage card then the phone will try to boot on the storage card, but I don't know how to make that. Thank's again.....
Hi!
Greats thank's again Rafivitto! I will try press cammera + volume + power end reset and the phone start the reflash. Merci beaucup.....
Hy all!
I have problem with clean boot logon... I done hard reset and device stuck at Clean Boot logon...
Would like to know how to flash it without activesync? I downloaded OEM ROM just can not install it without the NeoTouche beeing synchronized via active sync...
Please help how to do that without active sync...
Hi!
matjazz said:
Hy all!
I have problem with clean boot logon... I done hard reset and device stuck at Clean Boot logon...
Would like to know how to flash it without activesync? I downloaded OEM ROM just can not install it without the NeoTouche beeing synchronized via active sync...
Please help how to do that without active sync...
Click to expand...
Click to collapse
You need active sync for flash your s200 , so you plug usb cable between pc end phone with micro usb. After that you need to entre in bootloader mode ( for bootloader mode you need press simultanly power , camera end volume end reset while the red led is blinking) . If your led red is blinking then you can start flash rom with any flash , but I recomanded for you an original flash with ACER_EUU.exe hack , not originaly for that just download hack acer_euu.exe end replace it in directory flash rom. If you still can't make the reflash I need to know what is your version of rom? Your version is in the left corner on the first line. See you later....
update failed
Hello,
I wanted to update Neotouch from official rom 2.003.00_de to 3.003c.00_de.
The update failed and when i start the device, now I see on display:
- in the upper left corner: s200_3.003c.00_DE
- in the middle "clean boot"
- under it "acer"
I tryed to go in the bootloader mode:
I removed the Akku for ca. 10sek.
I connected device and PC via usb.
I pressed Volume down + camera buttons together, then the power button and when it starts to blinking the LED red, I press reset with the pen.
The LED is blinking red, but the display is black?
(it is correct?)
Then I started on PC the "EUU_Acer_S200_3.003c.00_DE_03.03.08_3.003c.00_20100205.exe"
...extracting...install prompt...ok...
window: "welcome to the device software update utility" etc. with the notifications to connect
... next..
and then:
"Update failed. The device software utility occurs trouble connecting to your device"
what am I doing wrong?
surdu or other , can you help?
Thanks!
I unpacked the originial
"EUU_Acer_S200_3.003c.00_DE_03.03.08_3.003c.00_201 00205.exe"
and replace the "ACER_EUU.exe" with
File
from this Thread
http://forum.xda-developers.com/showthread.php?t=628402
Then I clicked the "EUUFrontEnd.exe" and the "install prompt" started, then for a second, there is an Error window.
I searched in the posts here in neotouch forum for this problem, but idont understand much and my english is very bad.
Iam only user, I have no background knowledge. Please help me, if you can.
did you bring your device on "flash mode"?
what rom does it have now?
When I bouhgt mine I did excactly the same thing
It had 2.003.... official ROM and I flashed it with the new official 3.003b.....
camera+reset and then the steps as you did.
maybe it's something in the 3.003c drivers and the hacked .exe does not work..
Philippe_Raimo said:
did you bring your device on "flash mode"?
what rom does it have now?
Click to expand...
Click to collapse
1. I do not know exactly...
"I pressed Volume down + camera buttons together, then the power button and when it starts to blinking the LED red, I press reset with the pen.
The LED is blinking red, but the display is black?
(it is correct?)"
Is this really the Bootload Mode?
2. see my Post Nr. 14
Now i can see upper left corner: s200_3.003c.00_DE
maybe it's something in the 3.003c drivers and the hacked .exe does not work..
Click to expand...
Click to collapse
mmh..what should i do...
Hi!
olsching said:
1. I do not know exactly...
"I pressed Volume down + camera buttons together, then the power button and when it starts to blinking the LED red, I press reset with the pen.
The LED is blinking red, but the display is black?
(it is correct?)"
Is this really the Bootload Mode?
2. see my Post Nr. 14
Now i can see upper left corner: s200_3.003c.00_DE
Your phone S200 is not dead, you can save it, but is 2 way from the led red blinking, if your led red is on/off very well then is the bootloader, if the red led is blinking with have a small break (off) then you aren't in bootloader. Then you need press the Volume down + camera buttons + power button + reset with the pen , all the button togheter, while the red led is blinking (on / off) quickly end now you are in bootloader. After that you need Acer_EUU.exe Hack version v1 ( is exactaly - 3.432.960k ) .Just replace it end go. Good luck!
Click to expand...
Click to collapse
Hi Olscing! again
from this Thread
http://forum.xda-developers.com/showthread.php?t=628402 you download Hack v2 is no't good for you. You need v1 end the Acer S200_2.003.00_EN.
neotouch is running again
Thanks for your help surdu!
But now i could help myself
I flashed a customrom here from the forum. It stopped at 99,2%!
But the device was able to start and the rom runs.
Then i started the official acer update again and without problems it was installed. Now i happy again!
Hi room!
i have a problem with my tattoo, he won't boot at every time !
when i plug it to a PC or for charging, the red light is comming until the led light comes green.
it's not recognized on xp or win 7, and i can't enter in fastboot on recovery...
when i hold volume (+) and start, it vibrate 3 times and green led turns!!!
should i flash it with a Jitag ?
thank's
Does it show TATTOO on bootup, is it S-OFF ? What did you do to it and got it in that state ? Try to hold Volume down and then boot it up, that should get you in bootloader
...thanks for your answer!
i can't do anything (i tried to hold Volume down and boot it up but still nothing at screen).
i don't know if the old owner if he flashed it!
i have changed the battery and nothing.
S-OFF?? i can't answer.
when i plugged to my laptop or desktop, i see a red led (charging?!) but if boot it up (the light disappear and nothing at screen).
when i hold Volume up and boot it up, the phone vibrate 3 times and green led appears!!!!!!
another idea to help me ?
thanks
First of all thanks for not caring. I spend days on Internet trying to find a solution. I have Blade which I bricked thanks to my noob skills with flashing and similiar ****. I just want my normal phone back. Couldn't give a **** bout roms anymore. Sorry for the lang but Im mad. When I boot it up it just sits there on green android logo not going past. I can enter download mode if it matters. As soon as I back it up Im getting rid of cwm mode and bull****. I use my sister phone to transfer files on my sd card. I cant enter my recovery mode since I installed that **** of cwm.When I try the key combo-android logo stuck with red light on. My phone has 90-100% battery Im sure. I need a solution where I can do something from pc with download mode or something that will automatecly start when I boot up my phone that I transfered on my SD card. Please guys let me have some sleep. I've been staying all night long just to unbrick it. Dont mention any flashing rooting ****ing...I developed alergy to those words. I want it simple ..please...any help is appreciated. And sorry for my language.
Solution.
I Love The Register Video said:
First of all thanks for not caring. I spend days on Internet trying to find a solution. I have Blade which I bricked thanks to my noob skills with flashing and similiar ****. I just want my normal phone back. Couldn't give a **** bout roms anymore. Sorry for the lang but Im mad. When I boot it up it just sits there on green android logo not going past. I can enter download mode if it matters. As soon as I back it up Im getting rid of cwm mode and bull****. I use my sister phone to transfer files on my sd card. I cant enter my recovery mode since I installed that **** of cwm.When I try the key combo-android logo stuck with red light on. My phone has 90-100% battery Im sure. I need a solution where I can do something from pc with download mode or something that will automatecly start when I boot up my phone that I transfered on my SD card. Please guys let me have some sleep. I've been staying all night long just to unbrick it. Dont mention any flashing rooting ****ing...I developed alergy to those words. I want it simple ..please...any help is appreciated. And sorry for my language.
Click to expand...
Click to collapse
Calm down dude. If you can get in Download Mode , you are lucky. I even know people who had not get to Download Mode and had began to cry , cause the phones were only 3-4 Weeks old. Back to your problem.]First download here the stock rom.[/URL]
Then you need the Android SDK and the platform-tools from Google , so download it , cause you need ADB. Click here to get Android SDK.Then you need the ZTE drivers. Click here to get the drivers.Now get into download mode and connect the device via USB to your PC. Copy the boot.img (or recovery.img if it is in the ZIP package) and flash it via Fastboot (command: fastboot recovery.img) . Now you got the stock recovery. Now push the FULL update.zip at your sdcard , and now go to recovery , and update from sdcard , choose the update.zip ... Flashing takes a while. DO NOT WIPE ANYTHING BEFORE OR AFTER CHOOSING "UPDATE.ZIP" . Now your Phone should fully works normally
Hello, I have also bricked ZTE BLADE 3(I flashed a wrong kernel....). It only turns the red light on when i turn it on and blank screen, does not respond to vol + and vol - key, no android logo, but when I connect it to the computer via usb in Device Manager a COM port opens with the name ZTE DFU(Diagnostic interface). If anyone has experience of reviving this device from this mess? Thank you for your time
Zmaj5 said:
Hello, I have also bricked ZTE BLADE 3(I flashed a wrong kernel....). It only turns the red light on when i turn it on and blank screen, does not respond to vol + and vol - key, no android logo, but when I connect it to the computer via usb in Device Manager a COM port opens with the name ZTE DFU(Diagnostic interface). If anyone has experience of reviving this device from this mess? Thank you for your time
Click to expand...
Click to collapse
Your download screen is destroyed , but you are still able to get into it.
Try to get into it and flash the kernel with fastboot , the screen will bug during fastboot procedure.
My screen is completely blank and black, just the red light showing when i turn it on and it is always on. It does not respond on power button + vol. down, power button + vol. up, power button + vol. down + vol. up. When I connect it to the computer it does not show me a usb flash drive although I have the zte drivers installed and another sd card inside, but in Device Manager I can see it as a COM port(DFU) Diagnostic Interface. I tried accessing the bootloader via adb but it doesnt even list it with command "adb devices". I also tried flashing the recovery image via "fastboot recovery recovery.img" and "fastboot recovery.img" and still no luck, it just hangs at "waiting for device"...
Zmaj5 said:
My screen is completely blank and black, just the red light showing when i turn it on and it is always on. It does not respond on power button + vol. down, power button + vol. up, power button + vol. down + vol. up. When I connect it to the computer it does not show me a usb flash drive although I have the zte drivers installed and another sd card inside, but in Device Manager I can see it as a COM port(DFU) Diagnostic Interface. I tried accessing the bootloader via adb but it doesnt even list it with command "adb devices". I also tried flashing the recovery image via "fastboot recovery recovery.img" and "fastboot recovery.img" and still no luck, it just hangs at "waiting for device"...
Click to expand...
Click to collapse
When the red light still comes up , you still got chances to get it fixed...
I think so too.. but how? The only method left is JTAG... I saw a thread about using a TPT image to flash low level firmware using ZTEflash.exe but that thread was for ZTE Skate I think, I could not find the tpt.img file for zte blade 3.... Is there any other method via usb cable? Or send it to the shop?
Well, here is my situation:
Got a BLADE III Pro
Tried to root it and i played with few tools found on xda and other places (android forums). No luck at all. Tried to flash a CWM and NO LUCK neither. Tried to go back to flash stock CWM (as i was afraid of bricking it), searched for stock cwm and there is my BRICKED phone. When trying to hold volume down and power botton (both for over 20 seconds even) it will show a green android and its stuck there for hours. When trying to go to fast boot mode the same happens (with volume up and power botton).
While trying these two options the PC (Windows 7 64 bit) wont recognize the phone pluged in.
The only way the PC makes a sound is when i hold both volume up and down bottons and power it or plug it in the PC (without the battery even).
I need to know how can i fix it to boot only. PLEASE. Is this a "throw on can" phone now or it can be brought to life? PLEASE TELL ME PEOPLE.
pm me or any info as soon as you guys can.
I will respond to any question you might have.
Thank you in advance.
I have sent my phone to the shop and they said that they would need a jtag box specific for this model or a new motherboard for zte blade 3.... I think this the end for my zte blade 3