Related
Hello,
I have a big problem. I don't know what to do.
I wanted to make a clean install of OxygenOS 4.5.8 and so i downloaded it, did it on SD card together with Magisk and no_verity_op5.zip (because i read that this decrypt the data).
So i cleand data and installed no_verity_op5.zip via TWRP, but when i wanted to reboot it takes way to long (i waited 30minutes but it stays on boot circle)
After that i booted into TWRP and decided to made a factory reset and to install OxygonOS 4.5.8 in a clean version. But it was not possible anymore!
When i want to install the .zip it says Patching system image unconditionally... and it loads. after the blue is full it says:
writing static_nvbk image...
patching firmware images...
script succeeded: result was [1.000000]
And when i want to boot into system it says no OS installed.
I tried also to flash this rom or even any other custom rom through ADB Sideload but it does not work. Same like above..
What can i do? I do not know what to do
I hope my phone is not bricked.
Thank you for any suggestion.
Go to oneplus 5 official download page, download stock recovery and latest stock firmware and follow instructions on the download page.... But first with TWRP take a backup of all your data because restoring stock firmware will ERASE everything... Don't panic it will works
First off, don't panic! you're not bricked as long as you can reach your bootloader and recovery.
This happened to me as well and luckily the fix is easy!
You probably tried to flash the OxygenOS build from the Oneplus downloads right?
Somehow these won't flash properly through TWRP and you must therefore also flash the Oxygen recovery image listed in the downloads.
Here are some steps that'll fix your problem.
1 - Backup all of your private data from internal storage because flashing OxygenOS will WIPE/ENCRYPT all data on your device.
2 - Go to the Oneplus download center and download both the latest OxygenOS and it's appropriate recovery:
http://downloads.oneplus.net/oneplus-5/oneplus_5_oxygenos_4.5.8
3 - Boot into your bootloader and flash the stock recovery you just downloaded. (fastboot flash recovery <recovery>.img)
4 - Boot into the Oxygen recovery and flash OxygenOS.
This should get you up and running again.
Once you get tired of OxygenOS simply reboot back into your bootloader and flash TWRP and any rom of your liking.
In the future if you want to flash OxygenOS from TWRP you have to grab a build from XDA I guess. I'm not entirely sure why flashing from within TWRP won't work with stock OOS but I believe it expects to be flashed from withing the stock recovery.
I'm pretty confident this will solve your problems.
Please backup your data first though, don't want anything to get messed up in there!
Good luck!
Ok thank you.
i will try it.
So you are right, i tried to install OxygenOS with TWRP.
So is it not possible to have official OxygenOS with TWRP, Magisk and Root?
So i cannot backup OxygenOS with TWRP?
manuelbvb said:
Ok thank you.
i will try it.
So you are right, i tried to install OxygenOS with TWRP.
So is it not possible to have official OxygenOS with TWRP, Magisk and Root?
So i cannot backup OxygenOS with TWRP?
Click to expand...
Click to collapse
It is possible to have both OxygenOS and TWRP for sure!
Only a clean flash from a non-encrypted state in TWRP seems to break stuff. You can use a modified OOS build from the forums.
TWRP can indeed backup your OOS install so that shouldn't be a problem.
The only exception seems to be flashing a clean install of OxygenOS (from Oneplus Download center) through TWRP.
Other than that everything works as expected.
Ok thank you.
So i will follow you instructions and i hope it will work.
And i think so.
And after it i will install TWRP again (because i need the backup tool), i will install magisk. will this work?
So i can use everything as in a custom rom, but cannot make a clean install? So official Oneplus OTA will work with TWRP or not?
Thank you soooo much!
Also, Magisk/root works just fine on OxygenOS.
Once you flashed OOS from the stock recovery and have everything set up simply boot into your bootloader and flash TWRP.
From there you flash Magisk and everything should be fine.
OTA's from Oneplus also install fine through TWRP as long as you go into Magisk and uninstall 'root' first. When OxygenOS tells you there's an update simply remove Magisk as I said above and it'll update fine.
Ok thank you!
It worked!!!!! I am very happy!
So i will now install TWRP, and then magisk (newest version).
I have a question, because the last time i installed magisk it did not fully work.
If i install it i have root or? But how can i get saftynet in magisk?
manuelbvb said:
Ok thank you!
It worked!!!!! I am very happy!
So i will now install TWRP, and then magisk (newest version).
I have a question, because the last time i installed magisk it did not fully work.
If i install it i have root or? But how can i get saftynet in magisk?
Click to expand...
Click to collapse
First off! YAY!! glad it worked out!
Be sure to use the TWRP build from the twrp.me website. The one listed on these forums are 'unofficial'. Not saying those are bad, but the official one has a pretty impressive track-record.
After flashing Magisk you are root-enabled so yeah, congrats you are now root! In order to pass safetynet you must enable 'magisk hide' in the magisk manager (the app that should now be installed on your phone).
If you do not have an app called 'magisk manager' then you can download this app from the magisk forums. It should however install itself while flashing the Magisk zip. So assuming you have it installed find the 'magisk hide' service and enable it.
From my experience you sometimes need to reboot in order for it to pass safetynet check.
Glad it all worked out for you!
Everything worked!
Now i have OxygenOS 4.5.8 (with OTAs in future), magisk + root + saftynet and i can install something throug TWRP and backup.
SO PERFEKT.
You are a hero
manuelbvb said:
Everything worked!
Now i have OxygenOS 4.5.8 (with OTAs in future), magisk + root + saftynet and i can install something throug TWRP and backup.
SO PERFEKT.
You are a hero
Click to expand...
Click to collapse
That's great to hear!
Enjoy and take care!
no os
sideloaded zip for rom in twrp, says successful but then no os installed and I can't find the zip anywhere in twrp. help :]
xda___ said:
sideloaded zip for rom in twrp, says successful but then no os installed and I can't find the zip anywhere in twrp. help :]
Click to expand...
Click to collapse
Can't you just connect your phone to your PC and use MTP for the file transfer? Make sure to have MTP disabled under TWRP-> Mount -> Enable MTP
Zocker1304 said:
Can't you just connect your phone to your PC and use MTP for the file transfer? Make sure to have MTP disabled under TWRP-> Mount -> Enable MTP
Click to expand...
Click to collapse
I tried, windows recognizes my phone, but when I try to transfer files it it says device is not available or has been disconnected (something like that...)
xda___ said:
I tried, windows recognizes my phone, but when I try to transfer files it it says device is not available or has been disconnected (something like that...)
Click to expand...
Click to collapse
Well just flash a different twrp via fastboot flash recovery *path to file*
Pretty straight forward for those of us who like a nice clean flash. Not you dirty dogs.
1 clean flash lastest Android 10 factory image and install
2 setup the device don't set a password or pin
Install latest canary Magisk manager
3 pull the boot.img out of the Factory image zip.
4 move the boot image to phone internal storage
Patch boot.img with Magisk.
5 download latest twrp.img and fastboot boot it
Install the patches boot.img to your boot
Mount opposite partition if A then mount b, if b mount a
Ignore the error.
And repeat flashing patched boot.img like you did the first time
Mount original partition reboot. And boom
So installing the magisk canary build via zip in TWRP does not work?
---------- Post added at 04:07 PM ---------- Previous post was at 04:05 PM ----------
Also, did you use .019 or .020 build from the factory image website?
ne0ns4l4m4nder said:
Pretty straight forward for those of us who like a nice clean flash. Not you dirty dogs.
1 clean flash lastest Android 10 factory image and install
2 setup the device don't set a password or pin
Install latest canary Magisk manager
3 pull the boot.img out of the Factory image zip.
4 move the boot image to phone internal storage
Patch boot.img with Magisk.
5 download latest twrp.img and fastboot boot it
Install the patches boot.img to your boot
Mount opposite partition if A then mount b, if b mount a
Ignore the error.
And repeat flashing patched boot.img like you did the first time
Mount original partition reboot. And boom
Click to expand...
Click to collapse
Is patching the boot.img in magisk mentioned in step 4 an option in magisk? How do I "patch" the boot image?
How do I do this portion of step 5?:
Install the patches boot.img to your boot
Mount opposite partition if A then mount b, if b mount a
Does magisk store the patched boot image somewhere (and it tells you where) that is accessible in TWRP? then we need only go to that file path in TWRP under the "install" tab?
What does this mean?:
And repeat flashing patched boot.img like you did the first time
Do you mean on the partition you were originally on?
So if we're on A, mount B, install the patched boot image on A, remount A, install the patched boot image on B, and then reboot?
How do we "install to th boot?"
I used the .20 from the factory. And Magisk saves the patches boot.img for me in downloads, which I can access in twro
Good instructions but you don't even need TWRP if you want to save time. I just patched the boot.img with the Canary. 20 Magisk build and moved it over to my pc so that I could just flash it using the fastboot flash boot boot.img command. Worked like a champ and did not have to disable my security pin and jack with mounting A or B with TWRP.
I just flashed .20
Booted it once.
Then using fastboot I booted twrp, installed magisk 19.3
and Im rooted.
?* lol w.e works ?
Which magisk modules are workings?
tweaked said:
I just flashed .20
Booted it once.
Then using fastboot I booted twrp, installed magisk 19.3
and Im rooted.
Click to expand...
Click to collapse
Clean or dirty flash of A10?
I just flashed the canary magisk zip (from a booted/not installed TWRP) and it was fine... I didn't go through any extra steps.
hmm so now i have root following these instructions, but i cant seem to do much with it.. i cant seem to make system rw. cant edit build.prop to enable tether, cant edit host files for adaway. those are the two reasons i root, and neither seem to work.
edit: got adaway to work, needed to enable systemless hosts in magisk settings, reboot, then adaway works.
phyl0x said:
hmm so now i have root following these instructions, but i cant seem to do much with it.. i cant seem to make system rw. cant edit build.prop to enable tether, cant edit host files for adaway. those are the two reasons i root, and neither seem to work.
edit: got adaway to work, needed to enable systemless hosts in magisk settings, reboot, then adaway works.
Click to expand...
Click to collapse
I just flashed the factory image without the -W let it boot. Rebooted back to fastboot, booted Twrp, Flashed Twrp, Flashed magisk 19.3. All modules are working including Adaway except for the active edge mod.
dmarden said:
I just flashed the canary magisk zip (from a booted/not installed TWRP) and it was fine... I didn't go through any extra steps.
Click to expand...
Click to collapse
Which Canary please?
humdrum2009 said:
Which Canary please?
Click to expand...
Click to collapse
https://forum.xda-developers.com/apps/magisk/dev-magisk-canary-channel-bleeding-edge-t3839337
tweaked said:
I just flashed .20
Booted it once.
Then using fastboot I booted twrp, installed magisk 19.3
and Im rooted.
Click to expand...
Click to collapse
Did the same coming from 9.
What was new for me was the android 'no command' screen; power+volume-up -> menu .
Also had to reinstall Magisk in the manager (19.3), even as it was already installed, to get AdAway (systemless) to be able to alter the hosts.
Adb recognizes my phone and I manage to restart bootloader, but when I try to boot TWRP img it says "waiting for a device.."
What is wrong?
phyl0x said:
hmm so now i have root following these instructions, but i cant seem to do much with it.. i cant seem to make system rw. cant edit build.prop to enable tether, cant edit host files for adaway. those are the two reasons i root, and neither seem to work.
edit: got adaway to work, needed to enable systemless hosts in magisk settings, reboot, then adaway works.
Click to expand...
Click to collapse
I got tethering working (Verizon grandfathered unlimited plan)
1. Magisk -> Downloads -> MagiskHide Props Config
2. Magisk -> Downloads -> BusyBox
3. Reboot
4. Adb shell -> type ‘props'
5. Select ‘5’ -> ’net.tethering.noprovisioning’ -> y -> y
6. Wait for reboot
7. Adb shell -> settings put global tether_dun_required 0
8. Reboot
Adaway and tethering are my only reasons to be rooted as well. Glad both are working now on 10.
barski said:
I got tethering working (Verizon grandfathered unlimited plan)
1. Magisk -> Downloads -> MagiskHide Props Config
2. Magisk -> Downloads -> BusyBox
3. Reboot
4. Adb shell -> type ‘props'
5. Select ‘5’ -> ’net.tethering.noprovisioning’ -> y -> y
6. Wait for reboot
7. Adb shell -> settings put global tether_dun_required 0
8. Reboot
Adaway and tethering are my only reasons to be rooted as well. Glad both are working now on 10.
Click to expand...
Click to collapse
Awesome, yeah I am in the exact same boat as you, thanks for sharing that I will probably take the plunge and root as well. Which magisk version and twrp versions you use?
What kernel if any?
I'm running 10 now with root, I just flashed the latest canary build in twrp, didn't need to modify anything else. I do have a question though, has anybody been able to load up Titanium Backup? It just keeps crashing for me.
murphyjasonc said:
I just flashed the factory image without the -W let it boot. Rebooted back to fastboot, booted Twrp, Flashed Twrp, Flashed magisk 19.3. All modules are working including Adaway except for the active edge mod.
Click to expand...
Click to collapse
This is the way i usually root my device as well.
Flash a fresh rom
fastboot boot twrp.img
flash twrp.zip in twrp, reboot recovery
flash magisk.zip in twrp
reboot.
However after i flashed twrp then rebooted into it, the touch screen wouldn't work. I had to hold power + vol down to reboot into fastboot then i did the boot into twrp.img again and then i flashed magisk from there.
I have no idea why the flashed twrp is not working with the touchscreen. The twrp img and the twrp zip that i used were version 3.3.0-0 and magisk was 19.3.
In Magisk manager it says it is installed properly and that safety net check passes.
If we don't have TWRP,
How do we root the device?
Magisk has the option to patch a boot.img file. Technically, you could:
1. pull the boot.img file from the A10 OB1 zip
2. copy it to the phone's internal storage
3. install latest magisk manager, click on install - patch boot.img - choose the boot.img
4. copy the patched boot.img to a pc with ADB and USB drivers
5. put the phone in fastboot mode, sideload the boot.img
I have no idea if this would work, but you could give it a go. I believe that someone else already made a guide for exactly this here in the OP6T forum.
Refer to the twrp thread for OB 10.
https://forum.xda-developers.com/oneplus-6t/help/how-to-flash-twrp-android-10-beta-1-t3986345
Either do the OTA local upgrade and magisk uninstall then install to inactive slot method, or use the boot patch which there is another thread on that on the ROM Dev section.
I used the first, worked fine. But there is no supported twrp yet. Only magisk root is officially supported on Q.
Hello, After Root, it's impossible for me to boot on recovery mode
Always i'll want to do or, thé phone reboot on fastmode.
g4seb said:
Hello, After Root, it's impossible for me to boot on recovery mode
Always i'll want to do or, thé phone reboot on fastmode.
Click to expand...
Click to collapse
Yes, likely because the update flashed to the inactive, and there is no recovery now. So...if you want recovery, only way is to full wipe and do a MSM or flash all and wipe with older stable.
OP support/forums made announcements on their thread on what will happen with upgrading, or rolling back.
They have a rollback file you can download if you want it all working again including recovery. But you will get wiped as mentioned, and be back on the last stable and firmware. Then you can twrp and root all over again.
That is Beta testing for you!!
I've been running custom roms since before android was a thing so I'm usually pretty good at this stuff.
I'm running 11.0.9.9 IN11AA
It refuses to root. I'm not sure if there is some step I'm missing that's so obvious nobody mentions it?
I was rooted, but when the new Magisk 23 came out without Magisk hide.. it was a big problem for me. I have corporate apps that will refuse to work on a rooted device. I restored the stock images (just like I do to get my OTA).. but then I uninstalled Magisk 23 and Installed 22.1. I then patched the bootloader (Dire3ct Install) and all was good, until I rebooted and had no root.
My bootloader is unlocked.
So I downloaded the full stock rom v11.0.9.9 IN11AA directly from Oneplus.
Extracted payload.bin
Used Payload dumper to get the proper boot.img.
Copied boot.img to my device and used magisk 22.1 to patch the file.
Downloaded the patched boot.img to my desktop.
Used ADB to flash it
adb reboot bootloader
fastboot flash boot patched_boot.img
fastboot flash boot_a patched_boot.img
fastboot flash boot_b patched_boot.img
fastboot reboot
Nothing. No Root.
I tried this over and over with different versions of magisk.
I tried downloading pre-patched version, and using fastboot boot patched_boot.img.
The device just hangs, and then boots using the stock image. No root.
I have no idea what could be wrong.
Ideas?
I just updated from v11.0.8.8 to v11.0.9.9 today on the EU variant.
Downloaded the update via Oxygen Updater, then used the built in updater with the local file downloaded.
Before restarting the device, opened up Magisk, then clicked "Install to inactive slot" since the new update gets put on the inactive slot. After it installed, rebooted the phone, and done. Updated to latest, and kept root. Didn't even turn off the modules, although I only have 1 installed.
This is my usual method to keep root while updating.
I'm not sure where you got your Magisk from, but i'm using v23.0 from the official github page (HERE), and it still has MagiskHide built-in, and currently using it for all of my banking apps, and it works.
Most likely the issue is that you have used the old Magisk version to patch the file.
Download the app from the link above, and use that to patch your boot.img file.
While the extracted file should work as flashed, I like to just boot from it rather than flash it and make it "permanent".
Use fastboot boot patched_boot.img to boot using the file once only.
After starting up, you should have Magisk installed in a couple of seconds. It might prompt you to restart the phone when opening it first time, but just ignore that and do not restart as you'll lose the root. Alternatively, you can install the app when you're not rooted yet, and when you boot using the patched boot.img, you won't need to restart.
When done, Magisk should tell that you have 23.0(23000) installed.
Then just use the built-in Install > Direct Install (Recommended) option within Magisk to install it to the current slot.
Do NOT install it to inactive slot. This option only to be used when updating via OTA.
Other option:
Download the Magisk app from the link above, and rename it to magisk.zip then copy it to your phone.
Download TWRP from HERE to your PC and use fastboot flash recovery twrp.img to flash this recovery.
Reboot to recovery. (Might take 2-3 mins to boot first time)
Flash the magisk.zip using recovery.
That's all you should need to be able to root.
I appreciate the help.
I was so hopeful you gave me what I needed, but it didn't work.
So, It wasn't an update issue... it was more of an attempt to downgrade Magisk.
I always OTA the same way as you and it always works.
I also always get Magisk from the official Github page.
What I got excited about was that I wasnt aware there was a working TWRP! So I thought.. THAT will fix it.
I didnt flash it, I just booted from it. I flashed Magisk that way, BUT... still not rooted.
Here is the interesting bit.. when flashing Magisk via TWRP, it detected that my boot.img was already Magisk patched and not stock (Which is right). It's like the boot.img is correctly patched, Magisk just isn't seeing it.
I'd be ok with a full wipe and factory reset at this point, but I'm not even sure that will fix it.
** Edit - I tried manually flashing the latest full OOS downloaded from Oneplus. It didnt help. I finally factory reset and it's working now.
This is my fav. root method.
[GUIDE] Easiest way to root/magisk Oneplus 8 Pro
This method will not flash any custom recovery or any custom boots. Caution: I don't take any responsibility. Proceed with your own risk and resilience in mind Prerequisites: Oxygen OS 11 (tested with 11, issues reported with 10) and a PC with...
forum.xda-developers.com
ps000000 said:
This is my fav. root method.
[GUIDE] Easiest way to root/magisk Oneplus 8 Pro
This method will not flash any custom recovery or any custom boots. Caution: I don't take any responsibility. Proceed with your own risk and resilience in mind Prerequisites: Oxygen OS 11 (tested with 11, issues reported with 10) and a PC with...
forum.xda-developers.com
Click to expand...
Click to collapse
Agreed, this is a great method. I tried that too before I ended up doing a reset... no good. I somehow broke something with the rom outside of Magisk so that Magisk wouldnt work. Whatever it was, A full wipe fixed it..
Hello there, back in the day (2019 in March or April the phone shipped with Android 9) I rooted my galaxy S10+ Exynos with Magisk and stock recovery (because TWRP method did not exist yet or did but non twrp method looked safer, I forgot the reason)
Then I forgot about TWRP and even upgraded to Android 10 like this:
(standard procedure, download android with Friya, then patch ap file with magisk, then flash it with odin)
Well I used my phone as always, forgot about twrp, but always had a little voice in my head telling me, that twrp is good idea, what if something happens, I would at least be able to copy my data)
So I decided to flash twrp, to ease my mind a bit, and also be able to copy apps to /system/priv-app
So I am using Android 10 (see no reason to upgrade, what I need is there I prefer OneUI 2.0 over later versions and I dont want to make my device slower or loose some obscure api function that I dont even know exists until I need it)
Now, can I just use official twrp app and let it do its thing (I have root), or do I need to download twrp with the app, but prepatch it with magisk before I install it? (I read conflicting info, on xda they say you need to prepatch it, while on twrp guide: https://twrp.me/samsung/samsunggalaxys10plus.html
They say to just use the app if you already have root, so I am confused now
It seams using the app is the easiest and most safe method
Thanks for Anwsering and Best Regards
only in case recovery and boot share the same partition, you will lose magisk after flashing TWRP (does not apply)
alecxs said:
only in case recovery and boot share the same partition, you will lose magisk after flashing TWRP (does not apply)
Click to expand...
Click to collapse
well, I gues this did apply to me, because I tried to flash TWRP with the app (latest version: twrp-3.7.0_9-2 that the app offered, it offered 2 files .img or .img.tar, and I chose to flash .img), and now my phone cannot boot, its stuck in download mode it says with red letters
kernel: Could not do normal boot, (DT LOAD failed)
I don't know know what happened, I only flashed recovery, and bootloader is unlocked
adb doesn't work
I cannot even get to recovery
So what now? Can at least flash TWRP somehow back so I can get ot my files (I have most of my videos on an SD card, but 2 or 3 are on internal storage )
I would reflash Android 10 anyway if it wasn't for the files
you can flash recovery.img as tar file but that is useless for backup stock ROM userdata. if you still have the magisk_patched.tar you can flash it to get your data back. don't flash unpatched stock boot.img this will most likely result in data loss.
I would first try older TWRP as DT LOAD failed (device tree) looks like TWRP problem to me.
alecxs said:
you can flash recovery.img as tar file but that is useless for backup stock ROM userdata. if you still have the magisk_patched.tar you can flash it to get your data back. don't flash unpatched stock boot.img this will most likely result in data loss.
Click to expand...
Click to collapse
OK
after installing TWRMP
3.4.0 I got into recovery
I guess the latest version twrp-3.7.0_9-2 is broken (because I tried flashing from Odin and I got the same error
but 3.4.0 works now
Well then I got into a non rooted android state (I couldnt boot into the rooted one because if I held volume up I just got into TWRMP)
I do have my magisk patched AP file (I did keep that), so I tried flashing it by odin to get into rooted state again, but then got scared because I was aftaid it would delete my data, so pulled the plug out, immediately after I discovered its flashing system.img (it just started)
thats where I interupted it
<ID:0/035> SingleDownload.
<ID:0/035> dt.img
<ID:0/035> dtbo.img
<ID:0/035> system.img
<ID:0/035> __XmitData_Write
<ID:0/035> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
So then phone would not boot, not in TWRMP not in android anymore, so I flashed TWRMP again and now at least
I am in TWRMP (I can see my files, but they are encrypted (they have wierd names but size does seam to match my files)
So how do I reflash android now, without messing with /data partition?
or can I somehow backup just data partition, reflash android and flash /data back?
let the magisk_patched.tar flash, just make sure you don't flash CSC (HOME_CSC is fine it won't erase userdata)
alecxs said:
let the magisk_patched.tar flash, just make sure you don't flash CSC (HOME_CSC is fine it won't erase userdata)
Click to expand...
Click to collapse
Yey, that did it (that was scarry), now root works, as well as android 10 (for some reason Magisk Manager does not open (but all the magisk modules work)
Now, I did patch this ap file back in the day I updated android to 10 so
I used Magisk Manager 7.4.1.291c718b
and if I remember corecly (thanks got I recorded everything) I patched the AP file for Magisk 20.2-11b7076a)
Now I have Magisk Manager 8.0.7 installed
So after I downgraded my Magisk manager to 7.5.0 it opened
Now I just have to figure out how to install Magisk v21.4 which is the version that belongs to my Magisk Manager 8.0.7, because Magisk Manager won't let me install a custom magisk, it only wants to download the latest version
you can install latest Magisk apk and patch stock boot.img again. Anyway I would do a backup with Migrate and adb pull -a /sdcard first.
or you can paste this url as custom channel and install older magisk if you want to.
https://raw.githubusercontent.com/topjohnwu/magisk_files/b0694fad86/stable.json
alecxs said:
you can install latest Magisk apk and patch stock boot.img again. Anyway I would do a backup with Migrate and adb pull -a /sdcard first.
Click to expand...
Click to collapse
aha, I see
is there any other way besides patching my AP file again? (I mean Magisk can clearly update itself somehow)
I mean, Magisk Manager does open (but only version 7.5.0, not version 8.0.7), and I have root its just that I don't have Magisk Manager 8.0.7
So how do I install a specific Magisk version from Manager? (I did try to install like a Magisk module, but now I am stuck in download mode again, so lets install Android 10 again )
look in the json for download link
https://github.com/topjohnwu/Magisk/releases/download/manager-v8.0.7/MagiskManager-v8.0.7.apk
https://github.com/topjohnwu/magisk_files/commits/master/stable.json
https://github.com/topjohnwu/magisk-files/commits/master/stable.json
alecxs said:
look in the json for download link
https://github.com/topjohnwu/Magisk/releases/download/manager-v8.0.7/MagiskManager-v8.0.7.apk
https://github.com/topjohnwu/magisk_files/commits/master/stable.json
https://github.com/topjohnwu/magisk-files/commits/master/stable.json
Click to expand...
Click to collapse
OK, after I installed Android again (with my older prepatched magisk)
Not sure what happened but now Magisk Manager 8.0.7 opens and says I have 20.2-11b7076a installed
of course as this combo should not exist, magisk Manager cannot see any modules (modules are there in /data/adb/modules and they do work, its just that Magisk Manager cannot see them installed, which means you can not easly delete them and you could install them over and over again, since Manager would not know that they are there)
So now I need to find a way to update to Magisk 21.4
So how would I do that (I tried the module install method before (I downloaded 21.4 from official github release pages) , but that just got me stuck into download mode again, so any other way, is there a patcher for computer maybe?
I mean I can only install the latest version, even if I disable internet, I cannot select a specific version
refer to post #8
Thanks, after spending 3hours to get into magisk I decided to share my procedure (because I forget it a lot)
FIrst: make sure your phones last state was power off (you can eather power off from red button or from recovery)
Then turn phone on and start holding power button + bixby + volume up, and count to 10 then release (not 11, 10, if you count to 11 you will get to recovery)
To try out if you are in magisk mode (without ruining your saved wifi passwords), you can plug the phone into the charger, if it turn on normaly, you are in magisk, if it shows battery charging, then you are not in magisk mode)
OK, I tried updating Magisk with https://raw.githubusercontent.com/topjohnwu/magisk_files/b0694fad86/stable.json
but for some wierd reason, it doesn't want to update, its stuck on 20.2-1
OK,. I tried installing Magisk Manager v7.4.1 and when launching it, it said that it patched dtbo.img and it needs reboot, so after I reboot, I am stuck on download mode again
It sayd: DT table header check fail
well, lets install Android 10 a third time
wait, you're booting into recovery to get into Magisk? you can use Nemesis kernel to skip this.
https://forum.xda-developers.com/posts/81316371
alecxs said:
wait, you're booting into recovery to get into Magisk? you can use Nemesis kernel to skip this.
https://forum.xda-developers.com/posts/81316371
Click to expand...
Click to collapse
Yes I am, but its allright, I am used to this
one day I will have to compile my own kernel anyway (to add some drivers to the phone)
Now I have to figure out why Magisk 21.4 won't install
I tried patching my AP file with it, but no matter what I do, I cannot get into it for some reason? (even my trust and tried method does not get me into it, while it got me into 20 all the time)
Is this version broken?
Whats the latest magisk version that still supports Magisk Hide (usefull thing that always worked for me)
With Nemesis kernel no need for button dance, it boots straight into Magisk. Magisk Hide exist up to v23 but there is also unofficial Magisk v25
[Discussion] Magisk Delta - Another unofficial third-party Magisk fork
This is not an officially supported topjohnwu project. If you are looking for official Magisk source, please go to this page Introduction Custom Magisk fork by HuskyDG. Sync with official Magisk adding back MagiskHide...
forum.xda-developers.com
alecxs said:
only in case recovery and boot share the same partition, you will lose magisk after flashing TWRP (does not apply)
Click to expand...
Click to collapse
Magisk needs the ramdisk of the recovery/TWRP to patch it. If flashing a non-prepatched image you will lose root.
WoKoschekk said:
Magisk needs the ramdisk of the recovery/TWRP to patch it. If flashing a non-prepatched image you will lose root.
Click to expand...
Click to collapse
Yea, I discovered that already
Now I am trying to get it back and failing
UPDATE: after installing Magisk 23 (last version that has Magisk Hide), prepatching AP file, and flashing it like 10th time, I finaly have root
Do I dare to try TWRP again? (I guess I need to prepatch it with Magisk before I install it with odin? (but which file do I install there are 2 files provided (twrp-3.4.0-2-beyond2lte.img.tar or twrp-3.4.0-2-beyond2lte.img)?
patch the tar file