Related
Loving my Zuk, or was. I set up the screen lock for fingerprint sensor and it was working great. Recognises my thumb first time every time. Now though I can unlock with just a normal swipe. It doesn't even demand the backup pin number. I went back into settings and it still had the fingerprint setup as the screen lock so I removed it and set it up again and hey presto i was back in action but only for about 10 minutes and it went back to no security at all.
There were 4 small OTA updates today so I am guessing one of these has messed it up. Each update didn't say what it was for
Has anybody else had this issue?
Is working well for me.
Have you added other smartlock event (wifi, location, ecc) that can interfere with the lockscreen and disable it?
bartito said:
Is working well for me.
Have you added other smartlock event (wifi, location, ecc) that can interfere with the lockscreen and disable it?
Click to expand...
Click to collapse
My MOTO 360 is in smartlock as a trusted device, don't fully understand what smartlock is to be honest. If I remove it would it affect anything?
gibmonkeys said:
My MOTO 360 is in smartlock as a trusted device, don't fully understand what smartlock is to be honest. If I remove it would it affect anything?
Click to expand...
Click to collapse
Of course!
I have also a smartwatch (LG Urbane) and the watch as a trusted device. When the smartwatch is connected to the phone the lockscreen is always DEACTIVE, even if you have configured a lock screen (PIN, pattern and or fingerprint)
Power off your watch (or set if in airplane mode) to check if lockscreen turns on in the phone
bartito said:
Of course!
I have also a smartwatch (LG Urbane) and the watch as a trusted device. When the smartwatch is connected to the phone the lockscreen is always DEACTIVE, even if you have configured a lock screen (PIN, pattern and or fingerprint)
Click to expand...
Click to collapse
I have just removed my 360 as a trusted device and the screen lock now works perfectly and so I now understand how this works. Many thanks for the advice. I can now stop worrying that I have a faulty device!
gibmonkeys said:
I have just removed my 360 as a trusted device and the screen lock now works perfectly and so I now understand how this works. Many thanks for the advice. I can now stop worrying that I have a faulty device!
Click to expand...
Click to collapse
I am facing as well to a lockscreen and fingerprint issue.
I used fingerprint to open lockscreen and pattern as secondary. After showing the ZUK to somebody I needed to modify the pattern. From that time I am unable to switch back to fingerprint. Only three opportunities what I have, and no swipe or fingerprint, due to "Disabled by administrator, encryption policy or credential storage". What accessibility service messes up the fingerprint usage? Do you guys have an idea? All of them are swiched off.
---------- Post added at 01:17 PM ---------- Previous post was at 12:22 PM ----------
My problem is solved. I needed to delete credentials in security settings.
Hi. I'm having some problems with the fingerprint sensor. Is working intermitent or not. I've asked zuk support already but no answer yet. I don't know if it's a software issue or hardware. It's any way to calibrate the sensor? Maybe it's decalibrated? Any help will be usefull. Thank you.
LE I already made a factory reset. No improvement.
Cmdragan said:
Hi. I'm having some problems with the fingerprint sensor. Is working intermitent or not. I've asked zuk support already but no answer yet. I don't know if it's a software issue or hardware. It's any way to calibrate the sensor? Maybe it's decalibrated? Any help will be usefull. Thank you.
LE I already made a factory reset. No improvement.
Click to expand...
Click to collapse
I'm using the Zuk since a month, and no problems with the fingerprint at all.
In any occasions, the fingerprint sensor don't detects the finger the first time but at second try.
Since a few days, I'm on CyanogenMod (instead of Cyanogen OS) and I think the sensor is less responsive (sometimes I need to try three times or use the lock pattern).
But if you are with issues using CyanogenOS I think is due to a hardware issue.
bartito said:
I'm using the Zuk since a month, and no problems with the fingerprint at all.
In any occasions, the fingerprint sensor don't detects the finger the first time but at second try.
Since a few days, I'm on CyanogenMod (instead of Cyanogen OS) and I think the sensor is less responsive (sometimes I need to try three times or use the lock pattern).
But if you are with issues using CyanogenOS I think is due to a hardware issue.
Click to expand...
Click to collapse
I can not use the fingerprints touch button as back button anymore. this happened after last update cynogenmod. any knowledge.
thanks.
sadrettin said:
I can not use the fingerprints touch button as back button anymore. this happened after last update cynogenmod. any knowledge.
thanks.
Click to expand...
Click to collapse
Fingerprint actions has been removed by CM a few OTA updates ago.
I hope a kernel developer will add soon, but ZUK has not too much developers
Modded kernel for COS can be found in the other topic about this issue.
The OnePlus 2 sources happen to have a compatible finger print driver with capacitive button support which is currently being checked out for porting to the Chroma kernel.
So don't fret.. The feature can be restored.
iam not able to use my fingerprint lock, it was working well before but now suddenly it is not showing the option in CHOSE LOCK SCREEN- the SWIPE an d FINGER PRINT OPTION IS DISABLED.
how to enable it
Thanks ... I had the same issue & delete credentials in security settings.
I bought zuk z1 3days ago
Why We cannot use fingerprint sensor to lock and unlock the device for both purposes
Having an issue with the fingerprint sensor.....
Works fine but when push notifications(any notifications**) show up on the lock screen ..the sensor gets non responsive...mind u almost impossible to unlock
Have no choice other than security pin
And I Definitely think this is result of All IN ONE Issue
Say like.....1)fingerprint sensor integrated into hone Button, 2)Faulty software patching, 3) Me, adding two or more fingerprints
Any Suggestions from u guys Feels helpful
BTW....Bought the product via Amazon.in
Is there a provision in the ZUK Z1 which let's you interact with the device by simply tapping on the fingerprint sensor except on the lock screen?
If the device is locked and the screen is off too, simply placing my hand on the fingerprint sensor doesn't work. I always have to press on the button to wake the screen first.
Any help?
May sb tell me the modell of the finger print reader of the ZUK Z1? Pls. use AIDA64.
Gesendet von meinem Aquaris X5 Plus mit Tapatalk
@infistuff said:
Is there a provision in the ZUK Z1 which let's you interact with the device by simply tapping on the fingerprint sensor except on the lock screen?
If the device is locked and the screen is off too, simply placing my hand on the fingerprint sensor doesn't work. I always have to press on the button to wake the screen first.
Any help?
Click to expand...
Click to collapse
That's part the of custom roms. Fingerprint as home button can be activated by flashing something, you need root. But in the play store you can try https://play.google.com/store/apps/details?id=com.ztc1997.fingerprint2sleep
But it's not that what you need. Without root and a kernel where its implemented its not possible.
Hey my fingerprint was working fine till one day it just started vibrating when I tried to scan it. I tried deleting the saved fingerprints and registered new. I'm not even Able to register new fingerprints. What do I do?
Just got my second hand P8 from eBay. Someone told me the camera functions will not be working properly if I upgrade from 3.1 to 4.5 . Is this true ?
Please kindly advise.
gomcse2002 said:
Just got my second hand P8 from eBay. Someone told me the camera functions will not be working properly if I upgrade from 3.1 to 4.5 . Is this true ?
Please kindly advise.
Click to expand...
Click to collapse
You mean from EMUI 3.1( Lollipop) to EMUI 4.0( Marshmallow)?. EMUI 4.0 is way better in all aspects especially the camera which you get to have a manual mode. So go a head and update and don't listen to that someone.
battery is considerably worse for me on android 6/emui 4.0, if i were to be more precise i'd say about 30% worse compared to android 5/emui 3.1, the new emui fixed some bugs and introduced others, the UI is however a lot smoother on the new emui, transitions are a pleasure to look at, i rolled back to 5 though, battery life is most important to me
thanks for your feedback and I will stick around with Android Version 5
Arimasu said:
battery is considerably worse for me on android 6/emui 4.0, if i were to be more precise i'd say about 30% worse compared to android 5/emui 3.1, the new emui fixed some bugs and introduced others, the UI is however a lot smoother on the new emui, transitions are a pleasure to look at, i rolled back to 5 though, battery life is most important to me
Click to expand...
Click to collapse
Battery is not worse!
battery is noticable better in marshmallow, overall experience is smoother and faster, but im pissed of about music pausing when screen locked, it just hibernate stock or any music player even if i allowed it in battery optimalization, Huawei never again
b317 has bad battery life and it's a bit slower
i just updated to b321, it's way better,good battery life,it feels faster.
http://imgur.com/l5KWKvQ - from ~75% to 30% 2h41min SOT with auto brightness,wi-fi and cellular data always on,sometimes even location services and a bit of gaming....on b317 i was doing ~2h30min from 100% to 10% and i was trying hard to do this.
In Antutu i get 49915 on b321,on b317 i did ~25k
Hello,
I just updated mu huawei p8 to emui 4.0 and android 6.0 and my led notifications on viber and sms do not work.... Lite blinks when I receive mesage on whats up, messenger, when I have missed call....
But when I receive text messages led light or notification dos not work... Can you tell me how to fix this problem? Or if it is not fixable how can I go back on emui 3.1 and android 5.0 .
thank you
chipsy87 said:
Hello,
I just updated mu huawei p8 to emui 4.0 and android 6.0 and my led notifications on viber and sms do not work.... Lite blinks when I receive mesage on whats up, messenger, when I have missed call....
But when I receive text messages led light or notification dos not work... Can you tell me how to fix this problem? Or if it is not fixable how can I go back on emui 3.1 and android 5.0 .
thank you
Click to expand...
Click to collapse
This is a bug i think with the current marshmallow rom, use Light Manger app for the apps that you don't get notification for or for all apps.
p8
Is it better to go back on 5.0 or to wait for 6.0 update better then this beta version?
whit whitch version is my phone going to have better performance?
chipsy87 said:
Is it better to go back on 5.0 or to wait for 6.0 update better then this beta version?
whit whitch version is my phone going to have better performance?
Click to expand...
Click to collapse
It depends on you, i personally like Marshmallow everything works fine and better than Lollipop in all aspects, regarding the led notification you can try the app i suggested earlier, also the camera app is better on Marshmallow especially with the pro mode.
a
Rashad83 said:
It depends on you, i personally like Marshmallow everything works fine and better than Lollipop in all aspects, regarding the led notification you can try the app i suggested earlier, also the camera app is better on Marshmallow especially with the pro mode.
Click to expand...
Click to collapse
I tried light manager but led notification still doesen't work i also notised that sound on what's up notification doesen't work now...
Apparently I will have to wait 6.0 update whicth is not beta version....
thank you for answers I apreciate it
hi, my P8 lite (ALE-L21) has build: ALE-L21C185B180, anyone can guide me how to update it to Marshmallow, currently it is on Lolly-pop, on the official site there is no build for this.
Pls d mouthpiece of my honor6 is not working unless on loudspeaker when making calls.any help is appreciated tnx.
My fingerprint sensor doesn't seem to be working as when I add a fingerprint it occasionally says 'try againe' at the top of the screen and then won't register my finger print. If it does not do that then it retest eras my finger all the way till the last part and then don't respond or vibrate. How can I solve this issue?
I have the same issue.
Looks like I have the same issue as reported by my wife (I'm currently not in possession of the unit as I'm abroad and it has arrived few days back). She knows how to register as I have the Letv 1s and she was playing with it before.
The symptoms are as you say, no vibration and no detection of the fingerprint.
Can it be from the rom that came with the phone (maybe multilanguage). I can't remember if on 1s I had this problem.
Currently I have emailed the shop and I'm waiting for their reply. If you guys find a fix, please share.
Sent from my Letv X500 using XDA Free mobile app
valy_cta said:
Looks like I have the same issue as reported by my wife (I'm currently not in possession of the unit as I'm abroad and it has arrived few days back). She knows how to register as I have the Letv 1s and she was playing with it before.
The symptoms are as you say, no vibration and no detection of the fingerprint.
Can it be from the rom that came with the phone (maybe multilanguage). I can't remember if on 1s I had this problem.
Currently I have emailed the shop and I'm waiting for their reply. If you guys find a fix, please share.
Sent from my Letv X500 using XDA Free mobile app
Click to expand...
Click to collapse
Hi,
For me, the fingerprint scanner is the real weak point of this phone.
If it would have a better one, it would be flawless... except for the lack of development due to LeEco not publishing open source for their devices
And trust me : I've had the OP3 for several days before getting the LeEco. And that fingerprint scanner works as it should and in a blink of an eye you can use your phone !
What I found out is that this fingerprintscanner is really sssslllllooooowwwww....
So press it once, and then put your finger back on for several seconds.
But of course, doing so reduces the nice thing in having a fingerprint scanner as you're done quicker with "screen on" + "pattern/code"...
Really hope that LeEco can improve this... but when I see how they act on their own forums (a representative posts about every 20 days) I am not that optimistic
NexusPenguin said:
Hi,
For me, the fingerprint scanner is the real weak point of this phone.
If it would have a better one, it would be flawless... except for the lack of development due to LeEco not publishing open source for their devices
And trust me : I've had the OP3 for several days before getting the LeEco. And that fingerprint scanner works as it should and in a blink of an eye you can use your phone !
What I found out is that this fingerprintscanner is really sssslllllooooowwwww....
So press it once, and then put your finger back on for several seconds.
But of course, doing so reduces the nice thing in having a fingerprint scanner as you're done quicker with "screen on" + "pattern/code"...
Really hope that LeEco can improve this... but when I see how they act on their own forums (a representative posts about every 20 days) I am not that optimistic
Click to expand...
Click to collapse
For me the fingerprint Scanner is working perfectly. Faster than iPhone 6 und it only fails to read 1 out of 15. Got 3 prints registered and it does very well
katze94 said:
For me the fingerprint Scanner is working perfectly. Faster than iPhone 6 und it only fails to read 1 out of 15. Got 3 prints registered and it does very well
Click to expand...
Click to collapse
What version of the software are you using?
The fingerprint sensor has gotta be the worst ever in a mobile device. My phone takes good 5 seconds to unlock. Registering new fingerprints takes ages. Last I heard that this was some qualcomm tech which does scanning of skin layers under the top layer. But right now the technology is big fail.
That fingerprint sensor hardware is beta 1 in our phone. I am sure the new Le Max 3 which is coming out with Snapdragon 823 will not have this issue. They will advertise how the fingerprint is now 100x faster than before and bla bla.
magic_man said:
What version of the software are you using?
Click to expand...
Click to collapse
I am on TeamSpains Cm13 Version. In eui it wasnt that good but now its working without any problems
And to the guy over this post:. 5 seconds for fingerprint unlock? May be your device is faulty. I didnt experience this. Even not on stockrom
q
katze94 said:
I am on TeamSpains Cm13 Version. In eui it wasnt that good but now its working without any problems
And to the guy over this post:. 5 seconds for fingerprint unlock? May be your device is faulty. I didnt experience this. Even not on stockrom
Click to expand...
Click to collapse
Even my device on 15S unlockes after 5 seconds. The worst sensor and algorithm ever.
Hello guys,
One way to make finger print recognition better : save several time the same finger print.
Not very sexy but it works for me
So as I have arrived home, I've changed the firmware to 015s stock and the fingerprint started to work. Of course it's not ideal as my 1s but at least it's working. It takes about a second to read and unlock... acceptable to be honest. Maybe they will improve with the upgrades because for 1s it had improved within 2-3 firmwares to super fast recognition.
Sent from my Le X820 using XDA Free mobile app
My experiences after several ROM, the international Indian ROM has removed bug.
Recognition really fast, from 10 attempts 8 immediately.
Note!
By the installation Rome should be installed super su with.
The encoding is prevented with it.
i have the same experience here... got my max2 from geekbuying but wont even recognize my fingerprints... so i updated to 5.8 eui from india not the Chinese version and not it works... however it takes one sec to open slower than my honor 5x. ... hope leeco would make it a bit faster considering the new tech it has...
Is there a major difference between the indian rom and the stock chinese rom that has english language? Does the indian rom have english language selection?
Yes the system language is complete into English.
The fingerprint scanner on 5.8.16s is much improved It seems much faster now. There was even an upgrade notice at first boot where it said it would erase my previous prints to upgrade.
Thanks for the update, will try it.
Sent from my Le X820 using XDA Free mobile app
Guys in my device the fingerprint sensor working ONLY IN 5.6 EUI!!!no matter what rom i flash ,with full clean install i cant input a fingerprint!!!i have test every single rom who is based on EUI 5.8,EVEN THE OFFICIAL! IS NOT WORKING.i even try the latest 5.18.6s for x829...nothing..0...
any help will be appreciated pls.....
Z953RR said:
Guys in my device the fingerprint sensor working ONLY IN 5.6 EUI!!!no matter what rom i flash ,with full clean install i cant input a fingerprint!!!i have test every single rom who is based on EUI 5.8,EVEN THE OFFICIAL! IS NOT WORKING.i even try the latest 5.18.6s for x829...nothing..0...
any help will be appreciated pls.....
Click to expand...
Click to collapse
what i did on mine was download the indian rom 5.8 on my computer and renamed it as "update.zip"...then copy the file into the internal storage. ..once in internal storage, i used my file manager app to open it...then clixk update. your phone will update and wait about 15 minutes..iy will reboot and change your fingerprint via settings.... hope this helps
9449water said:
what i did on mine was download the indian rom 5.8 on my computer and renamed it as "update.zip"...then copy the file into the internal storage. ..once in internal storage, i used my file manager app to open it...then clixk update. your phone will update and wait about 15 minutes..iy will reboot and change your fingerprint via settings.... hope this helps
Click to expand...
Click to collapse
i ve try this rom too..no success...............
I am using Max pro m1 since 1 month and I face this issue where the fingerprint doesn't respond at all , It's doesn't even vibrate to acknowledge the failed recognition , I need to tap twice or more for it to know that I place a finger on the sensor and then it recognises.
I am on the latest build to date
1805.316 -> released on 12 July 2018
kenway66 said:
I am using Max pro m1 since 1 month and I face this issue where the fingerprint doesn't respond at all , It's doesn't even vibrate to acknowledge the failed recognition , I need to tap twice or more for it to know that I place a finger on the sensor and then it recognises.
I am on the latest build to date
1805.316 -> released on 12 July 2018
Click to expand...
Click to collapse
Known issue. Try tapping it with a slightly more force on the first try itself instead of just touching it lightly.
You will then get used to it after a few times.
candiesdoodle said:
Known issue. Try tapping it with a slightly more force on the first try itself instead of just touching it lightly.
You will then get used to it after a few times.
Click to expand...
Click to collapse
Ya , that's working.
Is it due to a cheap sensor , or software stuggling to render accuracy?
Thanks for the reply mate !
kenway66 said:
Ya , that's working.
Is it due to a cheap sensor , or software stuggling to render accuracy?
Thanks for the reply mate !
Click to expand...
Click to collapse
Mainly the first, partly the second.
Hi , I am using asus zenfone max pro m1, and i am facing fingerprint sensor problem as the touch is accessing 2 times, how to solve it.
https://forum.xda-developers.com/as...to/build-316-fingerprints-recognised-t3817555
similar issue
Asus zenfone max pro m1 Fingerprint Sensor Issue Solved
The issue is happened to me. Like in this issue i can't be able to use fingerprint sensor and do all the stuff to get rid of this. I even deleted all the fingerprint and after this i can't be able to add new fingerprint. But know from this trick i applied it's all solved. It's that you just have to restart your device and it all works fine. Yaa seriously.. Thankyou..
Yeah i too faced the issue. On day 1 itself after sometime my fingerprint sensor was not at all responding. I had to manually enter password to unlock. I deleted all my fingerprints. Restarted and added newly. Now Day 3 so far no problem with unlocking.
Me also faced this problem in 6gb 318 firmware
After restart working fine.
Same to me
after sometime my fingerprint sensor was not at all responding. I had to manually enter password to unlock.
Click to expand...
Click to collapse
Same for me 4GB variant user. There are times that it doesn't respond at all
hello senior experts re telegram group and custom rom link
i am looking for stable raily om for samsung trite snapdragon. sm 910
Capable of running important modern apps that require more recent android than marsmallow
for example sondbar setup headfone setup, fake gps ...the ones evryone use daily now.
not concerned about features or look of rom, just that it work properly.
the best so far aicp, however when powerd down with off button batt out in 3 days. ok if batt removed n put back.
I HAVE BOUGHT ANOTHER FONE MI 11 LITE 5G .. IT HAS NO PERMENANT MISSED MESSAGE ALERT (allways on display/alert menu option no permenant)
PLEASE
PLS could expert give me a link to telegram group with stable working daily rom that can run modern apps
OR PLS could expert give me link on xda for a stable working rom that runs the essential modern apps
Or PLS could expert give me link to the most recent aicp that would power off properly
THANKYOU
Need big led for missed messages, (or ALLWAYS on display with alert ... headfone jack, ... exp sd card storage, ir camera bluetooth and rcan un modern apps...
Ive now bought two fones as replacement, both not suitable, the other redmi note 9T 5g both no PERMENANT missed message alert while locked. (3rd party solutions ..aoe holie aodnotify dont work properly. )
Has anyone got a note 10... or s20fe or redmi note 10 pro 5g o they have permenant missed call alert please
did you find the most stable ? I am looking to.
LineageOS 18 is good but not stable (bluetooth, gps lock issues, battery drains when phone off, mobile data issues) with N910F
ResurrectionRemix....black screen at first launch after flaching
testing Havoc 4......which just crashed two days after flashing...bootloop
louisJJ said:
did you find the most stable ? I am looking to.
LineageOS 18 is good but not stable (bluetooth, gps lock issues, battery drains when phone off, mobile data issues) with N910F
ResurrectionRemix....black screen at first launch after flaching
testing Havoc 4......which just crashed two days after flashing...bootloop
Click to expand...
Click to collapse
louis.. you have the point exactly..... there seems to be no rom that makes the fone work relaiably, i dont care about features animation whatever, but fone bluetooth etc has to work reliably. "battery drains when fone off " so so so bad the rom cant be used like this. Ive bought 2 new 5g fones recently, the note 4 is way easier to use cause things like big led alert light. The latest missed message alert using aod on xiomi on many models only gives notification for 10 mins !! and 3rd party apps break on updates. please let me know and provide link if you find a note 4 snapdragon trite rom that makes the fone work reliably, and runs around android 9 so that modern apps like my soundbar setup will work.
gwm121 said:
louis.. you have the point exactly..... there seems to be no rom that makes the fone work relaiably, i dont care about features animation whatever, but fone bluetooth etc has to work reliably. "battery drains when fone off " so so so bad the rom cant be used like this. Ive bought 2 new 5g fones recently, the note 4 is way easier to use cause things like big led alert light. The latest missed message alert using aod on xiomi on many models only gives notification for 10 mins !! and 3rd party apps break on updates. please let me know and provide link if you find a note 4 snapdragon trite rom that makes the fone work reliably, and runs around android 9 so that modern apps like my soundbar setup will work.
Click to expand...
Click to collapse
louis, just so i understand, what exactly is the problem with getting a reliable stable rom, has something changed since android 9 aand 10 released, or did they never work properly? and is this a general rom problem, or is the 910f snapdragon difficult in some way? .. so if i load a custom rom onto my samsung ace 4 willi have the same problems, As said, for £150 can buy fab new 5g fone, but no permenant missed message alert led some no 3.5 jack , sd storage, infra red and of course removable battery. The most annoying is no PERMENANT missed message alert. Its difficult to find out if a particular fone have this or not from the helplines. (For others, the latest mi 11 lite 5g is max 10 mins aod, "permenant" does not exist on the settings menu. and 3rd party apps break on updates )
Actually, I am no expert so I don't what issues are there with new roms, but indeed they are not usable on a daily basis.