A dreaded white circle..any solutions??? - LG V20 Questions & Answers

Hi guys
I used uppercut/lgup with my F800L Korean version V20
I was able to put the phone in download mode and connect to the computer and flash the proper .KZD file. It fully flashes and completes without error HOWEVER after disconnecting the usb cable as the phone reboots, for a split second a large whitish circle pops up in the loading screen and says "erasing" below the circle. The phone does not continue on booting, just stuck at the starting logo.
Anyone know how to solve this? Thanks a lot in advance!!!

Anyone?

markmessier8888 said:
Hi guys
I used uppercut/lgup with my F800L Korean version V20
I was able to put the phone in download mode and connect to the computer and flash the proper .KZD file. It fully flashes and completes without error HOWEVER after disconnecting the usb cable as the phone reboots, for a split second a large whitish circle pops up in the loading screen and says "erasing" below the circle. The phone does not continue on booting, just stuck at the starting logo.
Anyone know how to solve this? Thanks a lot in advance!!!
Click to expand...
Click to collapse
Boot into recovery and Wipe. Power it off (Battery Pull), hold volume down, push power untill it vibrates. The LG logo will pop up, click the power button for a sec. (still holding the volume down button).

Excudent said:
Boot into recovery and Wipe. Power it off (Battery Pull), hold volume down, push power untill it vibrates. The LG logo will pop up, click the power button for a sec. (still holding the volume down button).
Click to expand...
Click to collapse
I have this same issue with a US996. I previous had LineageOS with TWRP, potentially with encryption. I did the LGUP to the stock KDZ and I am in stuck in the same boot loop. Doing the factory reset as described here, does not help.
---------- Post added at 02:39 PM ---------- Previous post was at 02:24 PM ----------
ck609 said:
I have this same issue with a US996. I previous had LineageOS with TWRP, potentially with encryption. I did the LGUP to the stock KDZ and I am in stuck in the same boot loop. Doing the factory reset as described here, does not help.
Click to expand...
Click to collapse
Turned out my battery was dead. Now it is stuck on the Secure start-up screen, asking for a PIN. I tried using any previous PINs doesn't seem to work. I will try to charge for a bit and factory reset again.

Related

LG G2 802 Soft Bricked

Hello.
I have an LG G2 802 that i managed to royally screw up last night, I was about to install the new firmware update for my phone, completely forgetting that i had a custom rom installed on it. After the firmware update was finished downloading, the phone rebooted into TWRP and would not boot normally after that, could not boot into the previous custom rom i had installed... I decided to wipe all the data, and try to use an old backup i had laying on the internal storage, got to it, wiped all data and started recovering the old backup. But the revovery wasn't working properly and it gave me an error, after fiddling around with TWRP a little more, i went into wipe -> advanced wipe -> and wiped everything, because i had an idea that i could just force a new rom over by ADB from my PC, and this all resulted in that I have no operating system, the phone boots into TWRP all the time, I've tried to hard reset it, but it just boots into TWRP whatever i do
Please help
Just flash a new KDZ over it. And next time check XDA if someone had the same problem as you and you will find the solution.
I've done a quick search about flashing a new kdz, and they involve getting into download mode, I can't access download mode, it just sends me to TWRP no matter what i do
Popps said:
Hello.
I have an LG G2 802 that i managed to royally screw up last night, I was about to install the new firmware update for my phone, completely forgetting that i had a custom rom installed on it. After the firmware update was finished downloading, the phone rebooted into TWRP and would not boot normally after that, could not boot into the previous custom rom i had installed... I decided to wipe all the data, and try to use an old backup i had laying on the internal storage, got to it, wiped all data and started recovering the old backup. But the revovery wasn't working properly and it gave me an error, after fiddling around with TWRP a little more, i went into wipe -> advanced wipe -> and wiped everything, because i had an idea that i could just force a new rom over by ADB from my PC, and this all resulted in that I have no operating system, the phone boots into TWRP all the time, I've tried to hard reset it, but it just boots into TWRP whatever i do
Please help
Click to expand...
Click to collapse
Are you able to boot into download mode?
---------- Post added at 09:42 AM ---------- Previous post was at 09:40 AM ----------
Ok Hold the power button until the phone flashes twice and then let go off the power button. When it's off, hold volume up and then connect it to USB simultaneously.
I just tried doing that, held the power off button until the LG logo flashed twice, the phone turned off, and then i held volume up button, LG logo appeared and then it just went straight into TWRP
Popps said:
I just tried doing that, held the power off button until the LG logo flashed twice, the phone turned off, and then i held volume up button, LG logo appeared and then it just went straight into TWRP
Click to expand...
Click to collapse
Ok, this time hold volume up and power button constantly while connected to USB. Report back.
Popps said:
I just tried doing that, held the power off button until the LG logo flashed twice, the phone turned off, and then i held volume up button, LG logo appeared and then it just went straight into TWRP
Click to expand...
Click to collapse
For those who have similar issues, I did the below steps:
1. While connected to computer in CWM recovery, install the drivers via PdaNet (these replace any original LG drivers)
http://forum.xda-developers.com/show....php?t=1983470
2. Connect to phone via ADB while still connected in CWM recovery (see below ADB download if you didn't already have it or forgot where it was)
http://forum.xda-developers.com/show....php?t=2317790
3. While connected via ADB you can use the same method as in the below thread (use the first one).
http://forum.xda-developers.com/show...1696&nocache=1
MK45A said:
Ok, this time hold volume up and power button constantly while connected to USB. Report back.
Click to expand...
Click to collapse
Tried it, it turns off, then the notification light at the top of the phone (beside the front camera) blinks 8 times if i constantly hold the volume up and power button, as soon as i release power button and volume up, the phone boots with the LG logo and then goes into TWRP.
Popps said:
Tried it, it turns off, then the notification light at the top of the phone (beside the front camera) blinks 8 times if i constantly hold the volume up and power button, as soon as i release power button and volume up, the phone boots with the LG logo and then goes into TWRP.
Click to expand...
Click to collapse
What he meant was, hold the Volume Up button & connect the phone to your PC. Don't have to hold power button at all. Try this mate.
Sent from my GT-I9000 using Tapatalk
robin786 said:
What he meant was, hold the Volume Up button & connect the phone to your PC. Don't have to hold power button at all. Try this mate.
Sent from my GT-I9000 using Tapatalk
Click to expand...
Click to collapse
Well, i tried this right now, the phone boots, LG logo shows, then it just goes straight into TWRP and nothing happens, i held the volume up, plugged the USB cable in (i could hear the sound in windows when you plug a device into your PC)
Popps said:
Tried it, it turns off, then the notification light at the top of the phone (beside the front camera) blinks 8 times if i constantly hold the volume up and power button, as soon as i release power button and volume up, the phone boots with the LG logo and then goes into TWRP.
Click to expand...
Click to collapse
When the notification LED starts to blink, let go of both buttons for a split second and hold them back again. Make sure USB is connected. Since you have TWRP working, Download should also be available.
---------- Post added at 02:24 PM ---------- Previous post was at 02:21 PM ----------
robin786 said:
What he meant was, hold the Volume Up button & connect the phone to your PC. Don't have to hold power button at all. Try this mate.
Sent from my GT-I9000 using Tapatalk
Click to expand...
Click to collapse
The problem is that you have to have the phone off to even attempt to get in to download mode.
MK45A said:
When the notification LED starts to blink, let go of both buttons for a split second and hold them back again. Make sure USB is connected. Since you have TWRP working, Download should also be available.
---------- Post added at 02:24 PM ---------- Previous post was at 02:21 PM ----------
The problem is that you have to have the phone off to even attempt to get in to download mode.
Click to expand...
Click to collapse
If i try to power off the phone WITH the usb cable connected to it, it just reboots automatically, so i cannot power off the phone without it rebooting all by itself, and then going into TWRP.
I tried to hold volume up and power while my phone was in TWRP and it rebooted, LG logo came up and then the red notification light started blinking, then i tried to do what you told me to, quickly release volume up and power button, while the LED was blinking, but nothing happened, other than the phone just rebooting, and then the LED started blinking red again, this just looped over and over again...
Turn it off, hold volume up and connect USB cable. Does it go to download mode?
robogo1982 said:
Turn it off, hold volume up and connect USB cable. Does it go to download mode?
Click to expand...
Click to collapse
No, the LG logo shows, then it goes into TWRP
have you tried this http://forum.xda-developers.com/showthread.php?t=2451696
Popps said:
Hello.
I have an LG G2 802 that i managed to royally screw up last night, I was about to install the new firmware update for my phone, completely forgetting that i had a custom rom installed on it. After the firmware update was finished downloading, the phone rebooted into TWRP and would not boot normally after that, could not boot into the previous custom rom i had installed... I decided to wipe all the data, and try to use an old backup i had laying on the internal storage, got to it, wiped all data and started recovering the old backup. But the revovery wasn't working properly and it gave me an error, after fiddling around with TWRP a little more, i went into wipe -> advanced wipe -> and wiped everything, because i had an idea that i could just force a new rom over by ADB from my PC, and this all resulted in that I have no operating system, the phone boots into TWRP all the time, I've tried to hard reset it, but it just boots into TWRP whatever i do
Please help
Click to expand...
Click to collapse
I had the same problem, stuck on logo lg , when i tried to go to download mode, i got stuck in the first step of it (i can't see the step with firmware update etc...) and when i tried to make a factory hard reset, it goes on the recovery mod.
After seeing many forums since 3-4 days, i tried to flash the kitkat kernel, so i used the adb sideload ---> so connected on recovery mod, then make install from sideload, then on your command (on windows) type adb sideload thenameofthekernel /sdcard/ and normally the recovery should install himself the kernel and you can reboot your phone
I still have an issue, can't access on download mode but i can use the phone as before, so if anyone can help, i listen you ^^
XxZombiePikachu said:
have you tried this http://forum.xda-developers.com/showthread.php?t=2451696
Click to expand...
Click to collapse
Just tried this, and when i turn on my phone, it only shows the LG logo, no TWRP this time, but i can't turn my phone off, it just restarts itself, and shows only the LG logo, cant get into download mode, i can get into the factory reset mode, but why would i go there when my phone doesn't have anything on it.....
Need some serious help
Popps said:
Just tried this, and when i turn on my phone, it only shows the LG logo, no TWRP this time, but i can't turn my phone off, it just restarts itself, and shows only the LG logo, cant get into download mode, i can get into the factory reset mode, but why would i go there when my phone doesn't have anything on it.....
Need some serious help
Click to expand...
Click to collapse
Hold down the power button till the it turns off and keep it held down the LG logo will flash up again then go off after that release it and wait a few seconds making sure the phone does not boot up again. Then hold down the volume up button and with the usb connected to the computer plug the USB into the phone this should then put it into download mode.
Why don't you sideload a rom in twrp recovery via adb?
twon23 said:
Hold down the power button till the it turns off and keep it held down the LG logo will flash up again then go off after that release it and wait a few seconds making sure the phone does not boot up again. Then hold down the volume up button and with the usb connected to the computer plug the USB into the phone this should then put it into download mode.
Why don't you sideload a rom in twrp recovery via adb?
Click to expand...
Click to collapse
I've already tried to get into download mode, and it doesn't let me, but now it wont even let me into TWRP, it's stuck at the LG logo, the notification light at the top is blinking in all different colors.
As i said, no download mode, now no TWRP...
Sangoku91 said:
I had the same problem, stuck on logo lg , when i tried to go to download mode, i got stuck in the first step of it (i can't see the step with firmware update etc...) and when i tried to make a factory hard reset, it goes on the recovery mod.
After seeing many forums since 3-4 days, i tried to flash the kitkat kernel, so i used the adb sideload ---> so connected on recovery mod, then make install from sideload, then on your command (on windows) type adb sideload thenameofthekernel /sdcard/ and normally the recovery should install himself the kernel and you can reboot your phone
I still have an issue, can't access on download mode but i can use the phone as before, so if anyone can help, i listen you ^^
Click to expand...
Click to collapse
I am in the same boat as you. Dont' know what to do.
When I try to boot into download mode - I see the initial screen but computer doesn't detect anything

G2 wont boot after hard reset, won't enter TWRP

Hi,
I`m ashamed to admit it, but i think i might have bricked my phone.
Long story short, i flashed TWRP 2.7.0.0, entered it, and did a hard reset, the one you have to type yes to confirm.
Then thinking i get a clean slate (stupid me) i rebooted, and now after the t-mobile logo there is NOTHING. just a green/blue flashing led.
I tried holding power+volume - but the phone is on, and i cannot turn it off. So i held both buttons till it reset and then after i saw the logo released and held again. Then i get a blinking red light.
I must have somehow deleted everything the phone contains?! even twrp? How is that possible, and why would it be an option in twrp?
Any help greatly appreciated!
Normally you should be able to switch the phone of completely by pressing only the power button till it reboots, but then don't release the power button for another let's say 5 seconds. After this your phone will be off completely and you can press power + volume down till the LG logo appears, then release very shortly and press again till it asks for factory reset. Press the power button till it says factory reset processing and it will boot into twrp. Normally you cannot whipe twrp with twrp [emoji6]
---------- Post added at 10:29 PM ---------- Previous post was at 10:28 PM ----------
When you can enter twrp you can sideload a Rom from your pc or install via otg
pffff, that was the trick.. managed to boot into twrp and now sideloading a rom.
thanks!

Help Please... Messed up new LG G2

Hey Guys... I've been searching XDA and the internet for a couple hours now on this, and am finally posting. I just got a new LG G2 on AT&T. I rooted with Towelroot, and rushed to change the DPI in Build.Prop without installing TWRP first, which was quite stupid... I changed it from 480 to 400 which has worked for me in the past on a previous G2 (on Verizon)...I don't have USB debugging enabled either.
In any case, when the phone boots up, it shows the AT&T logo, and then an error "Unfortunately the process com.android.systemui has stopped". I can hit OK...then I get a screen with just the wallpaper and an error "Unfortunately Home has stopped", and I can't hit anything.. it doesn't respond.
I installed the phone drivers from LG's site... I can't seem to connect via ADB or Fastboot (although I less familiar with Fastboot)... If I enter recovery by holding down power and volume down, it asks if I want to reset the phone, but doing so just gives me an error "error: boot certification verify" and reboots...
Is there any way I can connect via adb, fastboot, or some method to modify the build.prop file?
Thank you!!
@rockon83 I dont think there is a way to enter fastboot mode like that without a modded bootloader and adb also not.
You can try to get into download mode and flash stock kdz/tot again and then normal flash to keep your app data.
Thanks wulsic... If I press and hold the volume up and then plug in the usb cable, it just shows the charging battery symbol... I can't seem to get into download mode....
Am I screwed?
If You're just rooted can't you simply enter stock recovery and factory reset? Turn off the phone, hold vol down + power button together, when LG logo appears release then just hold power button. That should get you into stock recovery where you can factory reset.
revan17 said:
If You're just rooted can't you simply enter stock recovery and factory reset? Turn off the phone, hold vol down + power button together, when LG logo appears release then just hold power button. That should get you into stock recovery where you can factory reset.
Click to expand...
Click to collapse
Thanks revan... I tried that and I get an "error: boot certification verify" and the phone simply restarts....
Sent from my LG-D850 using Tapatalk
Same situation happened to me except for the not being to get into download mode part. Only way I was able to resolve it was to flash back to stock via the tot method. I used this video How to Unbrick or Restore the LG G2 ATT Version: http://youtu.be/kqw_LFuyHbE
I think there is a thread on here on how to fix not being able to get into download mode. But I think it's for the D802.
---------- Post added at 03:00 AM ---------- Previous post was at 02:58 AM ----------
Found it, but like I said I don't know if it will help you out.
http://forum.xda-developers.com/showthread.php?t=2582142
You can do try a factory reset. Hold down the VOL - and power, when you see the LG logo, let go then press and hold the power again.

[Q] Can't get into download mode, won't turn off, no boot logo

Rooted G2, tried to install TWRP custom recovery, the phone bricked.
- The phone is still on, but with a black screen.
- Windows recognizes something is plugged in and tries to format 16 partitions.
- The phone will not turn off. Everythign I could find (VolDown + pwr, VolUp + pwr, all 3 buttons, and just holding the power button) make the phone reboot over and over again. I can't see the screen power cycle, and I don't get any LG boot logo, but the phone keeps vibrating to let me know that it's power cycling every 5 - 6 seconds.
- I can't get into download mode, recovery mode, or even get the phone to show anything other than a black screen.
- LG flash tool throws errors when the phone is plugged in.
Any ideas on how I would get back to download mode?
screamatamonkey said:
Rooted G2, tried to install TWRP custom recovery, the phone bricked.
- The phone is still on, but with a black screen.
- Windows recognizes something is plugged in and tries to format 16 partitions.
- The phone will not turn off. Everythign I could find (VolDown + pwr, VolUp + pwr, all 3 buttons, and just holding the power button) make the phone reboot over and over again. I can't see the screen power cycle, and I don't get any LG boot logo, but the phone keeps vibrating to let me know that it's power cycling every 5 - 6 seconds.
- I can't get into download mode, recovery mode, or even get the phone to show anything other than a black screen.
- LG flash tool throws errors when the phone is plugged in.
Any ideas on how I would get back to download mode?
Click to expand...
Click to collapse
Pm me. Do you have a team viewer?
---------- Post added at 12:36 AM ---------- Previous post was at 12:29 AM ----------
screamatamonkey said:
Rooted G2, tried to install TWRP custom recovery, the phone bricked.
- The phone is still on, but with a black screen.
- Windows recognizes something is plugged in and tries to format 16 partitions.
- The phone will not turn off. Everythign I could find (VolDown + pwr, VolUp + pwr, all 3 buttons, and just holding the power button) make the phone reboot over and over again. I can't see the screen power cycle, and I don't get any LG boot logo, but the phone keeps vibrating to let me know that it's power cycling every 5 - 6 seconds.
- I can't get into download mode, recovery mode, or even get the phone to show anything other than a black screen.
- LG flash tool throws errors when the phone is plugged in.
Any ideas on how I would get back to download mode?
Click to expand...
Click to collapse
Use Srk tool you can Google and find the XDA page with the download.
xmayhemreturnsx said:
Pm me. Do you have a team viewer?
---------- Post added at 12:36 AM ---------- Previous post was at 12:29 AM ----------
Use Srk tool you can Google and find the XDA page with the download.
Click to expand...
Click to collapse
Dude, you are a LIFE SAVER! That Srk tool brought my phone back from the dead! Thank you so much!

Need Help- Bricked my LG G-2

accidentally flashed D80230e lollipop on my device which needed D80230d update. I flashed the .kdz using LG_Flash_Tool_2014. But after flashing the devices rebooted with the Android logo and then rebooted again with the LG logo and the LED light flashing. But the LED light (Bluish-green in color) keeps on flashing and the device won't turn on or go beyond that screen. I also can't get it into Download mode, it stays on the screen saying Download mode and doesn't go into actual Download Mode screen (pic attached). Help me get this thing in download mode please, I tried this method (http://forum.xda-developers.com/show....php?t=2582142) to access the partitions in Ubuntu but it didn't help as Ubuntu wasn't recognizing my phone or any partitions. The phone gets into official recovery mode where I get only one option i.e to factory reset and that doesn't help, after resetting the phone again turns on and stays @ LG logo with LED flashing. Kindly help me please
have a look at skr tools, see if it helps to get download mode to work.
Didn't help. When I start my phone normally, the laptop detects it as LGE Android DEvice. But in download mode the phone doesn't go beyond that screen shown above and the PC doesn't detect it either
http://forum.androidbg.com/showthread.php?tid=60499&pid=1225058#pid1225058
but this is bulgarian language
this help me for my bricked lg g2 D802
i had back up on my phone
but you can try usb otg after you go to recovery
---------- Post added at 09:33 AM ---------- Previous post was at 09:25 AM ----------
i had the same problem and this post save me bro try to fallow steps from the post
mostly the combination of the bottons
inserted is in fastboot and no exit or entry way in recovery, and to restore the system. I thought that there must be a button combination to enter in recovery, and ultimately there-On completely disconnected phone (to me had to stay for more than ten seconds Power key) is pressed first Volume Down and held simultaneously with Power button and it was held together with the Volume Down to the appearance of the logo of LG, placed in both the button and once again pushed to the appearance of menu Hard reset. Confirm by pressing the Power button and your phone after resetting enter into Rekoveri where it's easy, in my instances Restore ... Good luck
this si the translation from bg

Categories

Resources