Related
It happend while I was taking my cloths off for taking a bath
I dropped it inside our WC and my 2GB SD Card was gone far away inside that damn WC and never found it
I tried to pull out the battery but I couldn't pull that damn battery out for 5 min.
Anfter 5 hours drying with a hair dryer I put the battery and other stuff back and there was NO life After pushing the softreset hole some 10-20 times and putting it to charge there was a little life back some blue lines at the screen.
Now after 5 more hours it starts, but after some resets (some times there is only blue lines) and when it starts it freezez very much...
Should I send it for repairing?
Does the worranty covers it? (I bought it from Internet)
Would reflashing help?
Please advice...
tbh, I would have left it to dry normally in a warm place for 24 hrs before even considering to power it up, as (not 100% certain) I think the hairdryer creates static, which could damage the electronics inside, plus, you can't guarantee that it will have dried it out completely, which means, when you started it up, it could have still been damp in the middle and damaged something.
does it look like it has been water damaged? if not, then your best bet would be to not mention that fact, and just say it has suddenly started being funny, not booting up and freezing alot.
I doubt a reflash will fix it, but it is something for nothing, so worth a shot, however long it is.
*edit* if the company won't replace it, you could try your house insurance...
Thanks alot for the reply wytey,
I think there is something damaged, becouse when I soft reset it after freezing there comes a couple of times a light blue screen with blue and white lines...after soft reseting 3-4 times again it loads normaly again but freezez after 5-10 mins again
I was soo happy with my Jasjar >:'(
Your device has been damaged by water.
This is not covered by warranty.
It might not be covered by any insurrance you might have through your service provider.
You may be able to get it covered under home insurrance.
There isn't a case for a wet PDA. But I've read a recent article of getting back a Linksys router that has been soaked wet by rain water. See the real life experience here
http://www.grynx.com/index.php/projects/salvage-your-device-after-liquid-spill/1/
Probably you can do the same?
I dropped my Wizard in the bath, took out the battery and let it dry for about a day or so. Evrything works just fine.. So you should have dry it for over a day or more to be shure no water is left in it
Very timely.
http://www.lifehacker.com/software/hardware/save-your-electronics-from-spilled-liquid-150085.php
V
Thanks for replies guys,
Usefull article, but I think it's too late now, I couldn't take out the battery for 5 mins, then how to open the device and clean the components/circute
Can they prove it if I don't mention water?
Home insurrance would be a big lie, but who cares they get money from me every month (what to say to them? stolen? bropped in water?)
Thanks again for your times guys
I may be wrong , but I beleive there is an "indicator" in most modern equipment that shows up if there has been any water damage
anyone who knows how to repair phones and look at pcb boards etc. will KNOW right away that it has been water damaged. Impossible to hide (unless you yourself are also a technician).
I know because I own a phone repair shop and have been doing repairs for a lot of years.
One of the IC may be damaged, so when your device starts to get warm (as you said 5-10 mins) it cannot hold the power.
Just think yourself lucky that it's only an IC and not a CPU.
E-mail me on [email protected] if you need more help and advice
hb328_dtdd said:
anyone who knows how to repair phones and look at pcb boards etc. will KNOW right away that it has been water damaged. Impossible to hide (unless you yourself are also a technician).
I know because I own a phone repair shop and have been doing repairs for a lot of years.
One of the IC may be damaged, so when your device starts to get warm (as you said 5-10 mins) it cannot hold the power.
Just think yourself lucky that it's only an IC and not a CPU.
E-mail me on [email protected] if you need more help and advice
Click to expand...
Click to collapse
THanks alot for the info hb328_dtdd
If it's an IC, is it hard to repair it? how much would it cost me?
thanks
I (or whoever you decide to check the device) will have to open the unit up and clean out the residue of water and then do thorough tests first, it may not be an IC problem, even if it is an IC problem it may not actually be broken and will work again after cleaning and sonic waves passed through it.
Depending on which IC is broken and how hard it is to replace it, and also if it has caused any other side effects to the other chips, the repair in theory should not cost too much at all as it does not seem serious (from what I read from your post anyway).
E-mail me with more description of the problem and I will try and give you some tips to get it running, if that fails then you can decide whether to send it away or take it to local engineer to repair.
Hope this helps
the Gadget (Ch 5 UK )show did a piece on stuff getting wet. I htink they all came back to life one way or another but the were left to dry slowly I think for a day or 2. so you could hold out for live in the thing yet?
I hate the fact that Dopod 900 is very slippery, don't you think? I'm looking for a rubber casing like the one for O2 and Ipod.
Dopod 900 enclosure is too slippery, I'm so worry I may drop it too.
I am selling some Pocket PCs and this happened to two of my customers. But the device was an Ipaq 37XX and 38XX.
Both devices I put on a warm place and left there for 4 days. Then after this I powered them up. The Ipaq 37XX had only a bad LCD light, which was flickering sometimes and was not bright. the 38XX worked good again.
Anywasys, you need to check your device and have it cleaned. The biggest problem is the fact that there is so little space between smd mounted chips and the PCB that the water stays in between never drying and makes the metal rust. I had this experience with a cell phone already.
So you can try following:
(1) pay for cleaning and repair
or
(2) try to get it guarantee exchanged, which is also possible as for a pocket pc the technicians normally do not check for water damage. But if you have bad luck, somebody will notice this and you get nothing replaced.
I managed the same thing a while ago with my Xda2, and the symptoms were pretty much the same when it first happened (random lines and 'blotches' across the screen, freezing)..
Without haste, I removed the battery, sd card and mopped up any moisture from inside the battery compartment.. placed it in a warm place in an attempt to evaporate the moisture from the device. I left it for 24 hours before powering the device back up.
It DID work afterwards and I was a bit suprised and relieved at its resilience to liquid.
The important thing is to make sure the board and pins of the chips are not shorted by liquid, if you cannot get to the board, evaporation in a warm place is probably your best bet...Just watch out how you apply heat for the sake of the screen (and possibly the keys on the exec).
I dropped my XDA II into a canal and managed to save it. The problem is the water can't evaporate easily. I took the battery off and put it on a radiator. It took 7 days to finally dry out! It worked ok though.
You probably still have water in yours, so I would recommend putting it on a radiator or somewhere hot and just leaving it. You haven't got anything to lose
After almost 2 days inside the radiator it still has the same freezing/dying problem I thinks something is damaged inside ((( And now I can't find any electronic service in Denmark who can repare it
just because it's dry doesn't mean it fix itself, people often mistake this. Sometimes people get their phones to WORK after it's DRY but little do they know what is really happening inside the phone each time they power it back on and the residue is still there inside the phone lurking in the spaces between the pcb and the chips.
no matter what anyone says, I always tell people the same thing:
YOU MUST GET IT PROFESSIONALLY FIXED
My suggestion and this has never failed me yet.
1. After being dropped in liquid, DO NOT SWITCH ON - This is where most of the real damage will occur. If it is/was switched on remove battery as quickly as possible.
2. Strip down and remove any thing you can do easily, covers, sd card, stylus, sim, battery.
3. Waste a whole aerosol of switch cleaner, squirt it anywhere and everywhere you possibly can, literally fill it up with the stuff so it is pouring out of every hole. Do NOT use WD40, it must be electrical switch cleaner that will leave no residue at all!
4. Allow as much as possible of the switch cleaner to drip out and then allow it to dry, do not force dry with a hair dryer and even a radiator is too harsh. I find airing cupboard where the hot water tank is is the best place.
5. Leave at least 48 hours before putting everything back together and switching on, if it does not work straight away, strip it down again and leave another 24 hours, keep repeating for 7 days.
http://www.maplin.co.uk/Module.aspx?ModuleNo=27515&criteria=switch cleaner&doy=29m1
Good luck!
Hi,
As my wizard dropped in the water it got completely soaked.
I disassembled it to let it dry, see photos attached, put it together again and presto, almost everything works!!!
Just four keys of the keyboard do not work anymore, and as it all happened a week ago now I do not think this will be fixed.
Does anyone know if they do not work because of the water or because of the impact (the Wizard smashed on the street first)?
Has anybody ever fixed a faulty keypad?
Can anybody tell me where I can get a replacement keypad?
Let me know if you need instructions how to disassemble your wizard.
many thanks!
manhattan.
I have no answer to your question, but it is nice to see the inside of the wizard one time.
A couple of other people were asking about disassembly in other posts - so the instructions would probably be handy.
Hi,
I would love some complete instructions on dissasembly as I am about to take mine apart for painting and a hardware mod.
As far as the keyboard goes, you would be surpised how long they retain water, i doubt its a hardware problem, keyboard are pretty much solid state with only a tiny membrane for contacts. However it is this membrane that is most likely to be your problem, the contacts are very close together and covered in a film that can be verry attractive to water as it has rubber over it. So in essence I am saying I bet it is still wet in there, just a few droplets of condensation would do it.
Options, take it a apart and check and leave in a very warm dry place for a day, or II place whole wizard on a warm heater (not hot) for a while and see if that gets it.
T
Hi,
I also want to know the details of disassembly the wizard.
I think you had better post the instructions o disassembly here as I'm sure there are quite a few people who wuld like to know, me included.
Just a thought by looking at the picture (brave btw!)
Would it be possible to replace the 2,5mm headphone jack by an 3,5mm one and drill out a new hole for the larger connector?
Would be neat if you weren't so dependable on those stupid converters. Not a pretty sight anyway.
Thanks for sharing the photos.
I took mine apart some time ago to fix the stylist problem and when I put it back together some of the keys wouldnt work. The back light wouldnt work either. I found the problem was the little snap that secures the flat cable form the keyboard to the main board. There is a really small clasp that clicks down on the flat cable after you insert it into the connector. Once I took it back apart and snapped it, everything was normal again.
I plan on taking mine apart to change the keyboard form the English/arabic to just English, (anyone know where I can buy the keyboard/keys?) so any instructions you have will be appreciated.
Thanks
The stylii in the picture look like BA stylii.
Do I get 10 points?
will post instructions
OK guys I will put together the instructions and upload them here. I just have absolutely no time now so I hope you can wait a day or two....
Thanks for the comments. I am aware of the little lock that secures the mini flatcable that connects the keypad to the motherboard. I assume that is not the problem as I snapped it securely back in place.
I will try the heater suggestion, I suppose you mean to put the wizard in an oven set at let's say 50 degrees celsius?
The styluses in the photo are from my Qtek 2020. As the Wizard smashed I lost its stylus.... :-(
Sorry the photos do not show the display half of the wizard disassembled... I realised too late that others would benefit from pictures...
Cheers
Manhattan
I dont think I would put it in an oven. I would think that just inside a vehicle sitting in direct sunlight for a few hours would probably do, unless you are in a really cold climate. You may also try some electrical contact cleaner then get some additional heat to it after it evaportates. There is probably something that has trapped some moisture somewhere. Just for info, I dropped my Jamin the other night about 4 feet directly onto a tile floor. It bounced a couple times, ejected the SD card, and reset. But it is working fine. However, I had a bud that dropped his 2 day old Sony Ericsson P900 into water and dried it off immediatly and let it air dry. It worked, but he had problems ever since. It would drop calls and restart all the time. So there may not be a complete fix for it.
Good luck
Hey guys, someone posted the HTC Service manual for the Wizard!
In this manual you see pictures how to disassemble the phone!
It's realy the best manual to use for opening your mobile friend....
Good Luck
http://forum.xda-developers.com/viewtopic.php?t=43836
I've successfully fixed my girlfriends crappy creative keyboard once after water damage using a pencil. Depending how the keyboard is made, most of the time there will be really thin conductive tracks literally printed on the substrate. The water isn't particularly nice to these tracks and I found that in some parts there was noticale oxidation/corrosion. By very lightly scratching of the affeted paint and then going over it with a graphite pencil this did the trick.
Just an idea, personally I probably wouldn't do it to my vario but then again I'm still in the honeymoon phase with it.
Good luck
I fix phones for a living for many stores and have many phones that have water damage
what you dont do is charge it.. it will burn out the board
what you do is let it dry out, use the service manual and let it dry out in parts
then get white spirit and a toothbrush... dip it in and clean the contacts for yourk eys
once done, again let it try and then see how it goes. thats what i do, although we have a machine that sends out sonic pulses but the above method works too especially when im lazy
HTC Wizard Disassembly
hi guys. a lot of confusion over this simple matter. I don't know where the PDF file everyone's talking about is, most links didnt work, but here's some pics. USE AT YOUR OWN RISK! hahahahaha!
http://www.pdagold.com/articles/detail.asp?a=274
Hi,
I have a O2 xda model
IPL 1.01
SPL 2.21
GSM 01.12.10
OS 1.5.4.2
there is problem in formating the phone.
Even after a hard reset the Os wont boot,
it says that "formating is failed".
there is a prolem in the flash memory of the phone.
please help me with the assembly and disassembly process so that i can fix it.
Any one?
Hi everyone.
I remember some user made a topic with same problem, but i am not able to find it.
Theres some weird solution, like when you mix oil with water, inside or on top of my LCD. its in middle of the screen and the touch itself doesn't work properly where that weird patch is.
I tried drying it up but to no avail. I placed it in front of an air heater 7 to 8 inches apart. without battery, with screen side in front and then back side in front. first for 15 mins then for quite a bit of time.
First it went away but it appeared again when i turned it on. Did the drying again but it came again after some time (<-- didn't count it) i didn't even put the battery in it this time. Now i cant just keep it off so i am using it.
Any proper solution to kill this water thingy between lcd?
don't tell me to open it and clean it. The sale value would go crapppyyy low.
Hi,
I think your device has newton rings (use search in this forum to get more details). If your case matches, then send in to HTC service, this is usually covered under warranty.
If your device is not under warranty, you'll need to change the digitizer.
NOO!
This is it! i am done with this crap. Now i need to spend money in this stupidity?!?!? i just spent loads of money getting new PC, now i have to somehow ask my dad to get this repaired ? :/ and he will kill me too. whot its been 5months i got his.
I use the scotch tape to clean LCD's, but never knew one can fix it this away. nop i didn't helped.
Tried lighter trick, nop didn't helped. It moved/disappeared then came back.
i am extremely angry and disappointed.
Argh! i just spent the last 20 mins typing up a post and lost it! So lemme try this again...
Ok long story short, I goofed and dropped my s4 into a cup of coffee. It was submerged about 1/3 of the phone , on the top portion of the phone. I removed it immediately, pulled the battery and used a small vacuum to suck out as much of the liquid from the phone before i opened it up. Im pretty good with these kinda projects and have fixed many a phone over the years for friends who busted their screens etc. I hadnt been inside an S4 before this though, so i approached with caution. I used alcohol and a lint free microfiber brush to clean off anything that had coffee on it. All and all everything went pretty smoothly. After cleaning i put the phone in a bag of rice and silica gel for a few hours then put it back together and turned it on. It loaded up quick as usual, everything was pretty normal. But suddenly the screen would stop responding to my touches for a few seconds, and then start working again. So i turned it off, took it apart again and dug a lil deeper. I cleaned off all the contacts for the ribbons, and anything else that had any kinda sticky coffee residue on it. I put it back in the bag last last night and opened it up today and reassembled it. Turned it on , and like magic, everything was great! well 99% great. The phone is acting like it always has,and no more screen unresponsiveness or anything like that. All except for a small sliver of the top of the screen under the Samsung logo. Just a tiny sliver of the screen doesnt respond to my touches, which is a big pain in my butt because its just enough to not be able to swipe down the pulldown menu, and in some games i play, i cant click anything thats on the very edge of the screen in landscape mode. The screen looks normal, no signs of damage like ive seen in other devices when digitizers become damaged etc. Just that tiny little line of screen wont pick up touches.
I only went so far as to taking out the mobo and looking underneath that. I know i can go deeper, and would have to if i needed to replace the digitizer, but before i go through all that, i figured id seek the advice of the XDA Gurus first. Is there possibly anywhere else that i missed cleaning out the junk a that could be causing the problem in that area? Ive been very careful thus far and everything is working accordingly, hell the headphone jack even works still and that thing was full of coffee!! And all the other problems after the initial cleaning have gone away,and im left with this little line of screen that wont read my touches!! So i must have done something right so far! Im hoping that maybe i just overlooked another possible place to clean up any leftover junk and then will get full function of my screen again. if not, then i guess ill be ordering a new digitizer sometime soon.
Thanks for your time, anyone who reads this. I hope to hear some good news *crosses fingers* soon, and get my phone working properly again.
I'm impressed. Not just in your skills but with the build of the S4. Coffee is highly acidic. I once tore apart a keyboard that my wife spilled coffee on. The coffee etched the traces right off the P.C. board. If the S4 survived coffee on the inside workings they use a pretty good coating. It is possible they missed a spot and the coffee got it.
Sent from my SAMSUNG-SGH-I337 using Tapatalk
Hi all
I face of with a litle problem I have from some days a area of screean without touch haw can i repear this is this soft isue. I was traing few roms with the same result
florek235 said:
Hi all
I face of with a litle problem I have from some days a area of screean without touch haw can i repear this is this soft isue. I was traing few roms with the same result
Click to expand...
Click to collapse
Next time I recommend you use the search function... This has been discussed several times.
But yeah, you are not alone... This is a common problem or defect on the LG G2 (all variants). A few days ago I got the same problem where just a part of the top of the screen does not respond to touch.
As far as I could tell, the only solution is to replace the whole screen assembly or just the touch screen, but the replacing just the touch screen requires so much delicate and specialized work since the screen and the touchscreen are glued together so I recommend investing on a new screen-touchscreen replacement that will set you back about $80 USD but easier to replace by yourself.
I've been trying to figure what could have caused this on my G2 since I've never dropped it, but there are two possible scenarios for me:
1. A few days ago I was on a call on a very VERY hot and humid day, I was sweating like a pig and when I was on the phone, I noticed the receiver stopped working due to sweat coming into the speaker. I was stupid enough to blow into it trying to clear it, of course it didn't work but once it dried, the speaker worked again.
2. On a few occasions, I have forgotten to remove my phone from by back or front pocket when climbing into my car. I could imagine the phone would flex just a tiny bit and figure that might not be good, even though it was really not that much pressure nor time.
Those are the only two possible scenarios in my case. Other than that I don't see how it could have failed.
Cheers!
Rayanmx