Related
Hi,
is it possible to relock the bootloader to original factory mode.
fastboot oem lock (will erase userdata)
Also you should restore the fbop partition: /dev/block/bootdevice/by-name/fbop
For more reference see:
https://forum.xda-developers.com/axon-7/help/lock-unlocked-bootloader-t3444044
https://forum.xda-developers.com/showpost.php?p=68738854&postcount=100
Also please don't open a thread to a question that has already been answered several times.
After i unlocked bootloader my phone now is recognized as A2017U. When i relock it will it then recognized as original A2017G ?
I am interested in a tutorial about going back to stock for G model
The procedure for the g model is no different than the U model except you have to revert the bootloader (fbop partition) because the european model is quite restricted.
For making a tutorial I would need to know exactly what you modified.
There are already good step by step guides in this forum. All I could offer you are my backup files for the recovery and bootloader for the 2017G with update B08.
Bomberus said:
The procedure for the g model is no different than the U model except you have to revert the bootloader (fbop partition) because the european model is quite restricted.
For making a tutorial I would need to know exactly what you modified.
There are already good step by step guides in this forum. All I could offer you are my backup files for the recovery and bootloader for the 2017G with update B08.
Click to expand...
Click to collapse
At the moment i am on B09 rooted but I installed it via TWRP using DrakenFx's tutorial from here : https://forum.xda-developers.com/showpost.php?p=68873485&postcount=3
Futhermore when I unlocked the bootloader I was on B03 and I saved the aboot.img and fbop_lock.img .
Now I would like to go back to fully stock to prepare for the android N update.
I would highly appreciate it if you could offer me some directions for this matter.
Never tried this method (so I take no responsibility) but in order to receive ota you need an unmodified system with locked bootloader.
To lock your bootloader:
First backup all your apps, data and internal sdcard !
Connect your phone to a PC and start adb:
Type: "adb reboot bootloader"
Phone will restart: (if you are on linux, run fastboot with root permission)
Type: "fastboot oem device-info" (just to check things)
"fastboot oem lock" (will lock your bootloader)
According to DrakenFX you should have the stock recovery already installed. So you can flash a sd card upgrade from ZTE "http://www.ztedevice.com/support/detail?id=98CEB24F9FFD433EA99EC424163149A6" (to bring you back to stock)
If you still have TWRP use DrakenFX files to flash your system back to stock, but this time do not flash supersu.
You should be good to go and just have to wait for ZTE to release the update and apply it via the updater UI.
BTW this is my fastboot oem device-info output:
(bootloader) Device tampered: false
(bootloader) Device unlocked: true
(bootloader) Device critical unlocked: false
(bootloader) Charger screen enabled: true
(bootloader) Display panel:
OKAY [ 0.059s]
finished. total time: 0.059s
Click to expand...
Click to collapse
dodo34 said:
Hi,
is it possible to relock the bootloader to original factory mode.
Click to expand...
Click to collapse
You mind my asking the reason WHY you want to Relock?
If is cuz the N update , I'll rather keep it unlock base on @lokissmile thread and I'm 100% sure I'll be releasing N TWRP Flashable Zips for all variants when N is available.
i have G model and flashed the aboot of the U modell.
How to flash back now the aboot of the G modell back ?
Any help for the G modell ?
dodo34 said:
Any help for the G modell ?
Click to expand...
Click to collapse
as far my understanding the G model have factory images right? just download the one you were using and flash it using custom recovery.
LifeSupportZ said:
as far my understanding the G model have factory images right? just download the one you were using and flash it using custom recovery.
Click to expand...
Click to collapse
@dodo34
This is correct, the full image should be the one that contains both the emmc_appsboot.mbn (this is your aboot or bootloader partition) and the fastboot.img (the fbop or fastboot command partition) as well as recovery.img. This will set everything back to stock in one swoop. Otherwise you have to reflash the signed (tenfars) TWRP to flash back the fastboot image and then falsh back stock, since regular TWRP will either not be there anymore or will not run since BL is locked now
P.S, you can leave the fastboot alone for the purposes of OTA, no update so far hes checked on it and i am not sure if there is a G package with it since it has not changed from release, so as long as the image you flash has the bootloader and recover you should be good for N
P.S.2 Actually I see a little catch 22 here. If you lock the BL first, then you will not be able to run TWRP or boot into system if it was modified. You would need to flash the "signed" version of TWRP or flash stock recovery before locking the BL. Stock would be preferable since it can flash the factory package withouht modifications. If using TWRP i think you have to change updater-script to remove a .... and i just found another catch 22. The updater-script will look for product name P996A04 and if yours shows as 2017U the it will report back P996A01 so you will have to have a signed TWRP on there no matter what. Either to flash the backed up aboot fbop and recovery and then flash the full factory package through stock recovery or mod the updater-script and remove the assert line and flash the whole thing with TWRP. What do you get in TWRP shel when you run this "getprop ro.product.model"
peramikic said:
@dodo34
This is correct, the full image should be the one that contains both the emmc_appsboot.mbn (this is your aboot or bootloader partition) and the fastboot.img (the fbop or fastboot command partition) as well as recovery.img. This will set everything back to stock in one swoop. Otherwise you have to reflash the signed (tenfars) TWRP to flash back the fastboot image and then falsh back stock, since regular TWRP will either not be there anymore or will not run since BL is locked now
P.S, you can leave the fastboot alone for the purposes of OTA, no update so far hes checked on it and i am not sure if there is a G package with it since it has not changed from release, so as long as the image you flash has the bootloader and recover you should be good for N
P.S.2 Actually I see a little catch 22 here. If you lock the BL first, then you will not be able to run TWRP or boot into system if it was modified. You would need to flash the "signed" version of TWRP or flash stock recovery before locking the BL. Stock would be preferable since it can flash the factory package withouht modifications. If using TWRP i think you have to change updater-script to remove a .... and i just found another catch 22. The updater-script will look for product name P996A04 and if yours shows as 2017U the it will report back P996A01 so you will have to have a signed TWRP on there no matter what. Either to flash the backed up aboot fbop and recovery and then flash the full factory package through stock recovery or mod the updater-script and remove the assert line and flash the whole thing with TWRP. What do you get in TWRP shel when you run this "getprop ro.product.model"
Click to expand...
Click to collapse
if he mod the updater_script from official zte update to make it flash friendly, this is what i'll do,
* Mod updater script and remove aboot and recovery for now
* flash new zip without file mention above
* boot to bootloader while having custom recovery
* lock back the bootloader
* boot to custom recovery and perform " format data "
* create a flashable zip with stock aboot and recovery
* flash new zip with aboot and recovery
* reboot to recovery and check if boot to stock recovery and while in there perform a factory reset
i know is a lot of steps but, seems like is the way to go to get everything back in place without zte noticing anything.
Now i am on B06.
I put update.zip B08 and select update. But it boots to TWRP recovery and update fails.
@dodo34 If you are trying to restore from the OS system update you need to reflash your stock recovery for it to work properly. Wait for someone to confirm what I just said, but that's how it worked for me.
how can i flash my original recovery. what is the command for cmd ?
Please help restoring back original recovery.
dodo34 said:
Please help restoring back original recovery.
Click to expand...
Click to collapse
rczrider said:
Putting Your Axon 7 Back to Stock
If you want to revert back to stock and re-lock your bootloader (eg. sending the phone in for warranty work or are selling it), you should be able to do that using the steps below. It worked for me, anyway, exactly as written below.
Copy everything off your internal storage that you don't want to lose. If you're not rooted (so already stock, but with unlocked bootloader), skip to step 6 below. Otherwise, continue.
Grab the "StockSystem" zip for your variant from this thread and place on your microSD card: http://forum.xda-developers.com/axon-7/development/rom-guide-updates-to-stock-files-via-t3469484
Reboot into TWRP and wipe system, data, dalvik, and cache
Flash the StockSystem zip and power off (doing so will restore stock boot but does not appear to restore recovery)
Boot into EDL mode and flash stock recovery only: http://forum.xda-developers.com/axon-7/development/wip-axon-7-root-bootloader-unlokced-t3441204
Power off the phone, plug from computer, and then boot into stock recovery (hold Vol+ and press Pwr, continue holding Vol+ until recovery comes up)
Select "Wipe data / factory reset" and then "Yes"
After that finishes, select "Reboot to bootloader"
Plug in your phone into your computer and do: fastboot oem lock (see second post if this doesn't work and says <waiting for device>)
Your phone will reboot and should have been totally wiped (including internal storage) by doing the above
This should leave you with a stock, locked, and unrooted phone that can take OTAs. Note: it's possible (in fact, likely) that an OTA could break the ability to unlock your bootloader and gain root again, so be careful about going back to stock if you think you'll want to unlock/root later on!
If you need any stock files for B20 or B27 (stock recovery for re-locking, for example), you can get them here: http://forum.xda-developers.com/axon-7/development/untouched-b20-boot-recovery-files-t3443818
Click to expand...
Click to collapse
Try this guide from newbie unlock thread.
I get this error.
C:\Users\Intel\Downloads\Axon7\ADB>axon7tool -r
Usage:
axon7tool -r <boot|recovery|gpt> ...
axon7tool -w <boot|recovery>
C:\Users\Intel\Downloads\Axon7\ADB>axon7tool -r recovery
Connecting to device...
S: failed to read command
S: Failed to receive hello
terminate called after throwing an instance of 'std::runtime_error'
what(): error: Unknown error
This application has requested the Runtime to terminate it in an unusual way.
Please contact the application's support team for more information.
what i did.
Flashed Draken TWRP System Image B06
Flashed Draken TWRP Stcok Recovery B06
Flashed full update.zip B08
Now my phone is recognized as A2017G on the PC
But when i reboot the phone i get a message that the phone is unlocked and not trusted ?
why ?
Recently,something went wrong with my PH-1,so I decided to restore my phone.
My PC has been installed ADB and Fastboot system-wide with 15 seconds ADB Installer v1.4.3.It works fine with my Oneplus3 and Nexus6P but ruined my PH-1.
After unlocking the bootloader, the PH-1 was not being recongized via fastboot.Only with vendor ID,fastboot can work.
Code:
Code:
fastboot devices -i 0x2e17
I didn't treat it as a big deal.I fellow this thread [STOCK][DUMPS][FIRMWARE] Essential stock firmware and rom dumps to restore my PH-1.I got no errors, but unfortunately,my PH-1 was caught in a bootloop,it was keeping reboot into bootloader.I tried running flash-all.sh in Ubuntu,but changed nothing.
After a few days working on this problem,I finally figure out that maybe outdated fastboot were to blame. I uninstalled old fastboot driver and executables and replace them with Offical Essential device driver.Finally,after running one-click script flash-all.bat,my PH-1 come back to live!
If you run into those problem below,you may need to replace your installed fastboot with offical driver:
1. In Fastboot, you can use this command:
Code:
fastboot devices
After you run this command and you got nothing return.It means fastboot doesn't recognise your PH-1.
2. In Fastboot, you can use this command:
Code:
fastboot getvar current-slot
After you run this command and you cannot get a result of what partition your system is currently on (a or b).
3. When fastboot sends a large partition image( e.g. system) to PH-1 ,fastboot doesn't send it separately.
Normally fastboot will separate system image into four parts.
i got stuck in boot loop while flashing stock rom with mi flash tool.
i forgot to backup. i am on partition b. help me to get back on partition a
:crying::crying::crying::crying:
Command on PC should be:
"fastboot set_active a" or "fastboot set_active b"
To check your current slot type:
fastboot getvar current-slot
If you are flashing via Mi Flash and don't disturb the process in the middle, the slot doesn't really matter. Because Mi flash will flash both slots with same version during the process.
I wanted to make this post about my adventure with my old Pixel 2. I was getting non-stop red lines out of the log in TWRP. Many times I would have problems mounting system and vendor partitions as well as vendor partitions needing "to be cleaned".
This led me to believe that I may have a corrupted partition, so I did some research into how the partitions are organized, and what happens when you flash a lot of ROMs. Perhaps you want to go back to the stock firmware? Perhaps - like in my case - you want to install a ROM such as GrapheneOS that's meant to lock the bootloader afterwards, and act more like the stock ROM.
What I didn't understand up until recently is how exactly the A and B slots of phones like the Pixel 2 work. They work because the firmware allows updating OTA to the opposite slot of what's active. That way - in the worst case scenario - you can actually boot into the opposite slot and regain access to your phone. I'm not an expert on this, but that's my basic understanding.
So now that that's covered, another important aspect is flashing ROMs. If you are like me and like testing many different ROMs, you may end up running into issues such as the one I stated above with TWRP.
The only way I was able to avoid these types of issues is to run some commands through fastboot.
One such command is
Code:
fastboot format system
This command will format the system partition and make it easier to install ROMs without running into issues.
Another command is
Code:
fastboot format vendor
This command was very important in my case, because the vendor partition was actually unusable for my slot A. Doing this command finally fixed that issue.
Another thing to note is ROMs can be installed in both slots. A lot of people don't do this, because they leave their bootloader unlocked and probably just run the ROM for half a day, and flash another. In my case, I needed to flash both slots in order to lock the bootloader in GrapheneOS, and allow the OS to update OTA. If you don't flash both slots, that won't work.
Just to clarify further, these are the commands (at the bootloader) I ran (from a command prompt in Windows) in order from start to finish when I was flashing a ROM I wanted to keep:
Code:
fastboot --set-active=a
fastboot format system
fastboot format vendor
fastboot reboot bootloader
fastboot --set-active=b
fastboot format system
fastboot format vendor
fastboot reboot bootloader
fastboot flash bootloader bootloader.img
fastboot reboot bootloader
fastboot flash radio radio.img
fastboot reboot bootloader
fastboot update rom.zip
// Let the phone reboot into the new ROM, let it sit for a minute,
// then reboot into bootloader manually and then continue with fastboot:
fastboot --set-active=a
fastboot flash bootloader bootloader.img
fastboot reboot bootloader
fastboot flash radio radio.img
fastboot reboot bootloader
fastboot update rom.zip
Once I've done this, and can confirm it successfully loads into the ROM I've installed, I can now say that I have a clean, fresh install in BOTH slots A and B.
I'll update this thread if I can think of anything else that can help newbies like me.
Cheers!
HCFL said:
I wanted to make this post about my adventure with my old Pixel 2. I was getting non-stop red lines out of the log in TWRP. Many times I would have problems mounting system and vendor partitions as well as vendor partitions needing "to be cleaned".
This led me to believe that I may have a corrupted partition, so I did some research into how the partitions are organized, and what happens when you flash a lot of ROMs. Perhaps you want to go back to the stock firmware? Perhaps - like in my case - you want to install a ROM such as GrapheneOS that's meant to lock the bootloader afterwards, and act more like the stock ROM.
What I didn't understand up until recently is how exactly the A and B slots of phones like the Pixel 2 work. They work because the firmware allows updating OTA to the opposite slot of what's active. That way - in the worst case scenario - you can actually boot into the opposite slot and regain access to your phone. I'm not an expert on this, but that's my basic understanding.
So now that that's covered, another important aspect is flashing ROMs. If you are like me and like testing many different ROMs, you may end up running into issues such as the one I stated above with TWRP.
The only way I was able to avoid these types of issues is to run some commands through fastboot.
One such command is
Code:
fastboot format system
This command will format the system partition and make it easier to install ROMs without running into issues.
Another command is
Code:
fastboot format vendor
This command was very important in my case, because the vendor partition was actually unusable for my slot A. Doing this command finally fixed that issue.
Another thing to note is ROMs can be installed in both slots. A lot of people don't do this, because they leave their bootloader unlocked and probably just run the ROM for half a day, and flash another. In my case, I needed to flash both slots in order to lock the bootloader in GrapheneOS, and allow the OS to update OTA. If you don't flash both slots, that won't work.
Just to clarify further, these are the commands (at the bootloader) I ran (from a command prompt in Windows) in order from start to finish when I was flashing a ROM I wanted to keep:
Code:
fastboot --set-active=a
fastboot format system
fastboot format vendor
fastboot reboot bootloader
fastboot --set-active=b
fastboot format system
fastboot format vendor
fastboot reboot bootloader
fastboot flash bootloader bootloader.img
fastboot reboot bootloader
fastboot flash radio radio.img
fastboot reboot bootloader
fastboot update rom.zip
// Let the phone reboot into the new ROM, let it sit for a minute,
// then reboot into bootloader manually and then continue with fastboot:
fastboot --set-active=a
fastboot flash bootloader bootloader.img
fastboot reboot bootloader
fastboot flash radio radio.img
fastboot reboot bootloader
fastboot update rom.zip
Once I've done this, and can confirm it successfully loads into the ROM I've installed, I can now say that I have a clean, fresh install in BOTH slots A and B.
I'll update this thread if I can think of anything else that can help newbies like me.
Cheers!
Click to expand...
Click to collapse
Would this help in bootloop as well? I have a pixel 1st gen that does. I have flashed and or tried to anyways factory images...OTA and even was able to boot twrp and get lineage to flash, only to get a random reboot and bootloop. I would need to flash the factory image in order to get this phone operable. Should I flash a factory image and then do your steps or should I do the steps first and then flash the factory image?
Nope. Did not work. Seems as if the stock recovery is fubar
Things are changing with the advent of project treble and seamless updates. OnePlus will no longer release ROMs flashable via recovery (either stock) because is no more needed. The updates will be done on the slot not used for example if you are using slot a the update will be installed on slot b and the slot b will be set as default. If you brick and you are in bootloop how you can restore the rom? You can't with Stock ROM you have, because the zip can be only installed via Update Engine, so what can you do? Flash a stock rom via fastboot. I have extracted all images from the stock zip and i have made a new zip with the Fastboot ROM with a flash-all.bat included. This will work only if your bootloader is unlocked. This will erase all your data and will wipe your internal storage.
HOW TO FLASH
This version is only for not branded devices
Download the zip;
Unpack the zip in a folder;
Reboot the OnePlus 8 in fastboot-bootloader mode (Power and volume + and volume-);
Connect the OnePlus 8 to PC;
Run flash-all.bat flasher you need;
Wait until the process end;
The phone will automatically reboot.
DOWNLOAD
All roms on Sourceforge: https://sourceforge.net/projects/fastbootroms/files/OnePlus 8
BRANDED PHONE
For now branded device are not supported
MANUAL FLASH: Windows - OSX - Linux
If you want to manual flash these roms these are the commands (You need the latest sdk platform tools, you can find it here
Is reccomended to format data or the rom cannot boot:
Code:
fastboot -w
Others Commands to flash a fastboot rom
Code:
fastboot flash aop aop.img
fastboot flash bluetooth bluetooth.img
fastboot flash boot boot.img
fastboot flash dsp dsp.img
fastboot flash dtbo dtbo.img
fastboot flash LOGO LOGO.img
fastboot flash modem modem.img
fastboot flash oem_stanvbk oem_stanvbk.img
fastboot flash qupfw qupfw.img
fastboot flash storsec storsec.img
fastboot flash multiimgoem multiimgoem.img
fastboot flash uefisecapp uefisecapp.img
fastboot flash recovery recovery.img
fastboot --disable-verity flash vbmeta vbmeta.img
fastboot --disable-verity flash vbmeta_system vbmeta_system.img
fastboot flash opproduct opproduct.img
fastboot reboot fastboot
fastboot flash system system.img
fastboot flash vendor vendor.img
fastboot flash product product.img
fastboot reboot
REMEMBER
"Invalid sparce file format at header magic" is not an error, you need to wait a bit when you see that string, just wait.
If the device automatically reboot in Stock Recovery mode don't reboot it and wait the flash end.
These ROMs can't be used to update or downgrade your phone but just to restore your phone.
If the rom seems doesn't start go in recovery stock and follow this guideline: English -> Wipe data and cache -> Erase everything.
If you want to rebrand your phone from HydrogenOS to OxygenOS you can follow this guide: Rebrand Guide
If you want you can use also my tool to flash Factory Images, unlock bootloader, flash twrp or to understand if the device is recognized: https://toolaio.tk/
If you got some problems like write error or no partition, check this: https://forum.xda-developers.com/showpost.php?p=76658555&postcount=34
DONATE LINK
If you want to support this and others my projects please consider making a donation, thanks.
Branded devices is for example a Chinese version with HydrogenOS to which OxigenOS has been installed? If so, how can a branded device be recovered?
Thanks
Hi guys, i'm here again to ask for your support, actually with android 10 Google introduced a lot of changing, from dynamic partitions to the new keymaster 4 encryption/decryption. Teamwin is working hard to update TWRP but they will still take some time. Currently some things already work but there are difficulties in bringing them to the OnePlus 8/8 Pro, for example decryption already works but creates some problems on the OnePlus devices. That's why I decided to create a Paypal moneybox to be able to bring you the latest updates in the shortest time possible. As I have previously done, I assure you of a support of at least 2 years (within the limits of my possibilities). In addition to the TWRP I will improve the fastboot roms and add OnePlus 8/8 Pro to my TOOL ALL IN ONE (and maybe I will also bring the RevengeOS). By getting hold of a OnePlus 8 or 8 Pro I will also be able to improve the TWRP for OnePlus 7T and 7T Pro.
OnePlus 8/8 Pro PayPal MoneyBox: https://www.paypal.com/pools/c/8pfrIOL3Qa
If you are unable to participate in the PayPal moneybox, you can make a normal donation (perhaps specifying that it is for the moneybox), however all private donations that I will receive for this or other projects will be included in the moneybox.
Private PayPal Donations: https://www.paypal.me/MauronofrioTool
Why after flash it, it boot up to Qualcomm crashdump mode and how to fix?
sakun-ice said:
Branded devices is for example a Chinese version with HydrogenOS to which OxigenOS has been installed? If so, how can a branded device be recovered?
Thanks
Click to expand...
Click to collapse
I think unbranded devices mean the device bought from T-Mobile or Verizon. Nothing to do with chinese versiion flash oxygenOS, if I'm not wrong.
Can't seem to get this to work. I'm trying to flash a stock rom for my OnePlus 8 after bricking it during a rooting process.
The device' bootloader is obviously unlocked and i can get the phone into Fastboot mode and connected to my PC.
The only issue is when i execute the flash-all.bat file, it can't seem to flash any of the files and gives an error consisting of the message "FAILED (remote: 'Flashing is not allowed for Critical Partitions').
What to do guys? Can anyone help me out.
Does anyone know where to find mobile oneplus 8 5g tmobile from mine is bricked I had same error as post above
KJStar said:
Can't seem to get this to work. I'm trying to flash a stock rom for my OnePlus 8 after bricking it during a rooting process.
The device' bootloader is obviously unlocked and i can get the phone into Fastboot mode and connected to my PC.
The only issue is when i execute the flash-all.bat file, it can't seem to flash any of the files and gives an error consisting of the message "FAILED (remote: 'Flashing is not allowed for Critical Partitions').
What to do guys? Can anyone help me out.
Click to expand...
Click to collapse
Try to flash fastboot rom with "tool all in one),It worked for me.
I needed modem I forgot to fastboot reboot fastboot guy in post 6 that's all you need to do is reboot fastboot then flash all I was looking for different file
Never mind I fixed it by downloading ota and going to system updates in settings because fastboot won't flash to modem right
I am having issues flashing. flashing not allowed on critical partition. please help I tried to use the large address aware program but nothing has changed.
bluemoel said:
I am having issues flashing. flashing not allowed on critical partition. please help I tried to use the large address aware program but nothing has changed.
Click to expand...
Click to collapse
Make sure your on the latest update: 10.5.8
mauronofrio said:
Things are changing with the advent of project treble and seamless updates. OnePlus will no longer release ROMs flashable via recovery (either stock) because is no more needed. The updates will be done on the slot not used for example if you are using slot a the update will be installed on slot b and the slot b will be set as default. If you brick and you are in bootloop how you can restore the rom? You can't with Stock ROM you have, because the zip can be only installed via Update Engine, so what can you do? Flash a stock rom via fastboot. I have extracted all images from the stock zip and i have made a new zip with the Fastboot ROM with a flash-all.bat included. This will work only if your bootloader is unlocked. This will erase all your data and will wipe your internal storage.
HOW TO FLASH
This version is only for not branded devices
Download the zip;
Unpack the zip in a folder;
Reboot the OnePlus 8 in fastboot-bootloader mode (Power and volume + and volume-);
Connect the OnePlus 8 to PC;
Run flash-all.bat flasher you need;
Wait until the process end;
The phone will automatically reboot.
DOWNLOAD
All roms on Sourceforge: https://sourceforge.net/projects/fastbootroms/files/OnePlus 8
BRANDED PHONE
For now branded device are not supported
MANUAL FLASH: Windows - OSX - Linux
If you want to manual flash these roms these are the commands (You need the latest sdk platform tools, you can find it here
Is reccomended to format data or the rom cannot boot:
Code:
fastboot -w
Others Commands to flash a fastboot rom
Code:
fastboot flash aop aop.img
fastboot flash bluetooth bluetooth.img
fastboot flash boot boot.img
fastboot flash dsp dsp.img
fastboot flash dtbo dtbo.img
fastboot flash LOGO LOGO.img
fastboot flash modem modem.img
fastboot flash oem_stanvbk oem_stanvbk.img
fastboot flash qupfw qupfw.img
fastboot flash storsec storsec.img
fastboot flash multiimgoem multiimgoem.img
fastboot flash uefisecapp uefisecapp.img
fastboot flash recovery recovery.img
fastboot --disable-verity flash vbmeta vbmeta.img
fastboot --disable-verity flash vbmeta_system vbmeta_system.img
fastboot flash opproduct opproduct.img
fastboot reboot fastboot
fastboot flash system system.img
fastboot flash vendor vendor.img
fastboot flash product product.img
fastboot reboot
REMEMBER
"Invalid sparce file format at header magic" is not an error, you need to wait a bit when you see that string, just wait.
If the device automatically reboot in Stock Recovery mode don't reboot it and wait the flash end.
These ROMs can't be used to update or downgrade your phone but just to restore your phone.
If the rom seems doesn't start go in recovery stock and follow this guideline: English -> Wipe data and cache -> Erase everything.
If you want to rebrand your phone from HydrogenOS to OxygenOS you can follow this guide: Rebrand Guide
If you want you can use also my tool to flash Factory Images, unlock bootloader, flash twrp or to understand if the device is recognized: https://toolaio.tk/
If you got some problems like write error or no partition, check this: https://forum.xda-developers.com/showpost.php?p=76658555&postcount=34
DONATE LINK
If you want to support this and others my projects please consider making a donation, thanks.
Click to expand...
Click to collapse
Hi, do you know if patching with local update a Oxygen OS Europe release from a Global release may cause problems to the fingerprint? I have a IN2010 with the Global OxygenOS but I would like to switch to the European versione becasue I live in Italy like you
Why not flash reserve.img?
nnyd said:
Why not flash reserve.img?
Click to expand...
Click to collapse
Because it is placed in userdata and not in a dedicated partition
I have an issue trying to flash on fastboot. It's says I can't flash on critical partitions. Yes I know alot of people are saying that but what I haven't seen is this:
This is my problem:
Fastboot get device-info
(Bootloader) device unlocked:true
(Bootloader) device critical unlock: false
(Bootloader) charger screen enabled: true
I have already tried "fastboot flashing unlock_critical"
It says bootloader already unlocked. I then re lock bootloader which I know is not a good idea( reflash stock with msm tool) and it lock then I try unlock critical command again and it still says device critical unlock: false
i need help please ..
i tried this method not the latest version i tried the 10.5.4 global
so it gave me all failed and error to foramt and others
then it restart my phone to show me crashdump
what should i do ?
should i use latest version ?
i hope you replay fast .. thank you
Alucardo1 said:
i tried this method not the latest version i tried the 10.5.4 global
so it gave me all failed and error to foramt and others
then it restart my phone to show me crashdump
what should i do ?
should i use latest version ?
i hope you replay fast .. thank you
Click to expand...
Click to collapse
Try again with 10.5.7. When it reboot to recovery, let it continue to run till it reboots on its own.
Unbrick from fastboot method
I hope I can help someone since I spent the whole night trying various methods to unbrick my Oneplus 8 and only this one worked for me JUST FOR INTERNATIONAL VERSION
You must have the drivers installed (Adb & Fastboot)
You must have your phone with the bootloader unlocked
1.- Download the file
2.-Unzip it
inside you will find Flash-all.bat
3.-Enter Fastboot mode
4.-Double click on the Flash-all.bat command
5.-It will direct you to the recovery, select the English language and restart in fastboot mode so that the process continues, wait for it to finish flashing everything and ready, the phone restarts on the latest version
https://mega.nz/folder/8tpUSSrR#7wH4NX_ccr2a6Ub8LXpsEA
Donate Link to support my work
https://paypal.me/pakomorales?locale.x=es_XC
cannot relock bootloader on oneplus 8
bro thanks for fastboot room for oneplus 8,i flash your fastboot room 10.5.9 everthing ok,but i relocked to boot loader it the phone be correpted. what should i do ,
please help me.