hi, I have a problem with the print server. I use it in an office with 6 PCs connected to the network. The problem is that sometimes it prints many pages with strange characters.
the printer is a lexmark e352dn, regularly recognized by cups via ppd.
the raspberry is connected to a network via LAN a cisco linsys e3000 router. The 6 computers are windows (7 and 10).
the printer is connected via the usb port to the raspberry.
I usually print these strange characters when I print from a web page (e-mail receipts or when I open the pdf in the browser) but sometimes it does so with word 2010.
The printer is just usb and is far from the other computers, so I thought of connecting it to the rasp and sharing it with the others. I checked this morning and in the printer properties it is not connected to any ip address, as if it were not connected via ip. practically I went in ret, I looked for the printer among the shared resources and I installed the drivers through windows on windows
Related
i got usb wlan adapter. it's ip is 192.168.1.130.
the lan adapter in my pc has 192.168.1.84 ip.
all computers on my local wired network has 192.168.1.* addresses and 255.255.255.0 subnet.
i fixed the IP of SD sandisk wifi adapter on my mda compact to 192.168.1.131.
Usb adapter is in peer-to-peer (ad-hoc) mode and i normaly connect with ppc to it. i got 80-100% signal all the time.
the problem/question #1: why i cant ping from ppc to PC ? firewall turned off.
#2 - if i could ping it, would i be able to ping all the other ip's on my wired network?
#3 - if i could be able to ping all of those computers, how should i set-up a workgroup on ppc and be able to map network drives through wlan link?
#4 - if i would be able to map the drive over wifi link, would i be able to add mine 20.000 mp3s to the pocketmusic's playlist and play them wirelessly?
thanks in advance!
And when i ping from PPC - i see on pc that "received" packets are raising -
ie. now it shows 12 packets received, when i run ping on ppc to pc, the
number increases to 16 (4 pings!) but all are time-outed....
And if the IP on both sides are set to "automaticly", they got assigned
169.254.*.* IP's. Then the ping goes through correctly but i can't still
access the network. The network bridge between LAN and WLAN connection only
made things worser, making my internet connection unusuable (DSL through the
same LAN connection) so i deleted the bridge. Now - ping is going but i
still cant map my pc's drive.... what could be the problem...
Same problem
Dakky,
I have the exact same problem. I bought a Netgear WG111 Wireless USB dongle. I created an ad-hoc network, connected to it but can't connect to the internet or browse my shared. On my desktop the sent packet go up but not the recieved.
Are we both being stupid, can't you connect your PPC to your PC using an ad-hoc network? I have now tried to connect with two different desktops to my XDA and a friends XDA IIs running WM5 to my desktop but had no success. I can connect to an access point and browse file/internet no problem.
I have an XDA EXEC and run XP Pro on desktop.
I've got similar problem. I have Linksys Wireless-G usb network adapter, i assign same class IP adresses (192.168.2.1, 192.168.2.2, mask 255.255.255.0) the wifi connects in ad-hoc modebut how can sync over wifi ?, if I am able to sync over wify i will be able to use my pc's internet connection wich is a lot faster than any gprs/edge
I don't think you can network in this way - basically you have a bunch of clients but no 'server' I think you need a wireless hub (with Internet connection in there somewhere) in there somewhere.
If you do a search on microsoft web site ther is some info about using a PC as an internet share for other PCs but you have to use a very specific IP address rnge for this and set the share PC up in a certain way
Anyone get these two to play nice together?
Details:
Cisco PIX 501e at the office
WM6 3g phone (HTC TyTn II)
vista/xp laptop (working properly on either would be great right now )
VPN setup on the pix is, i believe, fine. I could be wrong tho, i set it up by trial and error + reading the manual having never even touched a cisco device before
It works tho and has worked flawlessly for months now with Cisco VPN Client on XP or Vista machines.
Old phone was WM5 and used the clunky and annoying modem emulator to enable a laptop to use it to connect to intarwebs in the middle of nowhere, this was great and after faffing about getting it setup worked fine (required you to be logged in as administrator on vista tho :\ and not just a user account with admin privileges, actually administrator. Annoying.)
New phone is WM6 and uses internet sharing to connect with a laptop, this is a much better solution with no faffing about in vista and XP
Problem: Cisco VPN client connects to the pix through Internet Sharing on the phone just fine, however no traffic gets through.
Cannot ping, web browse, dns, rdc or anything to the network at work. Tried with Cisco VPN client v4.6.00.0049 and v5.0.01.0600 on XP and v5.0.00.0340 on Vista, none work.
This sucks
Now, i know its not a problem with the laptop or the vpn software on the laptop as these work fine when connected over ethernet or wifi.
Its not a problem with the phone's 3g connection, i installed a trial of bluefire vpn client onto it and that connects to the vpn and works just fine when the phone is in standalone mode.
However for the life of me i cannot get the two bloody things to work together.
Plz halp
Hi,
Often times, the inability to ping a local host (computers or other connected devices e.g router, hardware firewall, printer, PPC, etc) or hosts, is due to the firewall not allowing traffic through the router. It can also be that the hosts are incorrectly configured to be on different subnets, even though they are local, as in your own case.
Proceed as follows to troubleshoot:
a). Ping the router
Note that the idea is to see if we can establish communication with the router or hardware firewall such as the Pix.
At command prompt (c:\>) type:
ping 192.168.0.1
(each router manufacturer uses a different default internal IP address for its router) - the one above is for a Netgear or D-Link router - for a Cisco router, you would need to know the Cisco IOS command - see your router manual for this.
b). ipconfig /all
Note: there is a space before the forwardslash.
When it returns the parameters, check to see that the IP addresses are all on the same subnet.
This is crucially important for you to take good note. If you are not able to ping a local host or gateway, it's most likely due to this.
c). Ping the Pix Firewall (using its IP address)
d). Ping a remote IP address, e.g. your ISP's gateway or DNS server
e). Is there traffic? If it returns successfully, then ping the other hosts, including the VPN client.
Pix Firewall
Check to see that the Access Control List is configured correctly by ensuring that the IP addresses of the connected hosts have been entered, with the relevant access rights.
Router
Log on to the router. Whilst there:
Ensure that the hosts (computers, etc) are all on the SAME subnet. If they are on different subnets, you must correct the IP addresses to reflect that they are on the same subnet.
Note: If you do really want them to be on different subnets, then you need to use a default gateway.
Hope this helps.
kiwi992.
I have been searching for more than 3 hours for some kind of driver for my T-Mobile Dash, to use it as a GPRS/EDGE Modem. My iBook is an old G3 model, so even if I were willing to purchase Missing Sync (which I'm not, btw), my iBook is not supported, as it is not a G4 or better.
I am looking for a FREE driver for OS X 10.4 Tiger, specifically an "RNDIS" driver. I am not particularly looking for speculation. I believe I have the correct modem scripts, but I can't get my Mac to see the USB Modem. Yes, I have put my Dash into ICS mode. Yes, I am running Windows Mobile 6. Yes, I have all of the updates to OS X. Yes, I have tried searching the forums (this one, and several others). Yes, I have tried "Googling it", which produced much good information, but no solutions to my problem. Although my Dash is Bluetooth enabled, my iBook is not. Yes, I know I can add a USB Adapter. I may well do that in the near future. Right now, however, I'm just looking for an RNDIS USB driver for Mac OS X. I don't need Synchronization features, at the moment.
Anyone have any ideas??
Correction: Does anyone have any "good" ideas??
Thanks,
--Aaron
I just wanted to touch this and see if anyone had any information to help. My girlfriend has a new Pantech Duo and I would like to get USB tethering working for that. I did find a couple sites that may help (HowTo: USB Internet Sharing With Linux And Windows Mobile 6), but I don't know enough about the technology to feel comfortable trying it. Thanks.
I use my wizard as a modem sometimes just using Internet Sharing in my TNT Rom. You may be able to find a .cab for it. From there just use activesync/WMDC. I haven't tried it on activesync, only on WMDC.
he's using mac
download wmwifirouter by chainfire or the free trial of walkinghotspot (if your handset and mac have wifi), or a micro bluetooth dongle if not.
leoni1980 said:
download wmwifirouter by chainfire or the free trial of walkinghotspot (if your handset and mac have wifi), or a micro bluetooth dongle if not.
Click to expand...
Click to collapse
Pantech Duo doesn't have Wifi. That was my first attempt before I realized it didn't have it, because I'm using that solution with my Kaiser.
RE: bluetooth. I haven't had a lot of success with a reliable connection. I've tried with my Kaiser and successfully configured it, using it to connect three or four times from my house, but as soon as I went on the road, I couldn't get it to connect at all, using the same steps as before. I'm sure that's either karma or equipment smarter then operator, but I'm hoping for a USB solution for simplicity (theoretically) as well as the better data throughput.
SyncMate
Well, if you are using a Mac then here is what i used to do before I got Missing Sync.
For Syncing contacts and dates and such i used Eltima Softwares SyncMate. Runs pretty good and can be done using the USB cable. It also provides the option to do it over Wifi, which is faster. The Full version allows your to Sync even more stuff I believe.
For Syncing files, I simply paired my phone with my mac and transfered the mp3's, jpg's, etc.
Hope this helps,
Paul
Welcome to the hell which is created when you have a Mac and a WM device!
I have been mucking around with trying to get my internet connection shared with my MacBook pro for a couple of months. Here is what I have tried
- Bluetooth PAN - There is an issue with the MacBook Pro whereby the bluetooth PAN will produce incredibly bad latency issues rendering it useless
- Modem Scripts (Bluetooth)- Have never found one which would connect....I have tried a few
- Mobile Stream (USB) - Never managed to get a connection. The support team said that they had never seen the issues I sent in logs. They will investigate and hopefully resolve in future releases.
-PDAnet (Bluetooth)- It actually works! although it seems to hang the dialer process on the Mac periodically which requires a reboot to resolve
-Wifirouter - It works although it caused issues with access points in the office and drained the battery very quickly.....even when powered from the MAC it would empty the battery. Worked OK when using a mains charger.
-VMware Fusion to XP desktop (USB) - Works and works well however you can't provide (well i havent got it working) an internet connection to the Host Mac.
At the moment I am using the PDAnet 'solution' but I am always looking for something more reliable. A usb connection would be better and more reliable as there seems to be big issues on the Mac bluetooth environment.
Cheers
Aidan
Hell, I couldn't even find an RNDIS driver for windows (apart from installing ActiveSync) which is why I made the Linux post.
Yeah, OSX is *nix based, but I don't think you can use Linux packages on it, what I know about macs could be written on the back of a postage stamp though.
Regarding the VMWare solution, did you try enabling internet sharing for WinXP in the VMWare session (using a different IP to the one the Mac uses) and set the default gateway of the Mac to the IP of the XP machine in VMWare?
What I mean here is that the PPC shares the connection to the VMWare windows machine via USB and the VMWare windows shares the connection to the Mac via TCP/IP.
To be honest I never really played about with sharing the virtual machine with OSX too much. I was a bit put off with running fusion like that all the time as it sucks the life out of the battery when out and about.
Until a better solution is available I will stick with PDAnet. It does put me off windows mobile (slightly) moving forward. It would be interesting to see if the Bluetooth PAN connection works correctly without the latency issue on the diamond when it is available. If it worked properly it would be the best solution.
Cheers
Aidan
Read http://forum.xda-developers.com/showthread.php?p=2398248 for a review & comparison of WalkingHotSpot
With VMWare Fusion, setup VPN connection for the OS X host to connect through guest
evilc said:
Hell, I couldn't even find an RNDIS driver for windows (apart from installing ActiveSync) which is why I made the Linux post.
Yeah, OSX is *nix based, but I don't think you can use Linux packages on it, what I know about macs could be written on the back of a postage stamp though.
Regarding the VMWare solution, did you try enabling internet sharing for WinXP in the VMWare session (using a different IP to the one the Mac uses) and set the default gateway of the Mac to the IP of the XP machine in VMWare?
What I mean here is that the PPC shares the connection to the VMWare windows machine via USB and the VMWare windows shares the connection to the Mac via TCP/IP.
Click to expand...
Click to collapse
I was reading this thread and you gave me the idea which led me to a workable solution so I thought I'd share back. I'm in the same boat as many ppl with latest MBP which doesn't work well with BT PAN (slooooowwwww). I sort of needed Fusion anyway since I'm starting to write WPF apps and performance is terrible over RDP from OSX (different subject). Anyway, here are some keys to getting this to work:
1. Setup a private network (not bridged or nat)
2. Install activesync on guest and fire up 'Internet Sharing' from WM6 device and connect device to Mac with USB cable.
-at this point you should be able to get online from the guest OS through the mobile device as previous post indicates-
Here is where the fun starts:
3. Create an advanced network connection on the guest (accept incoming connections, aka VPN connection)
4. *IMPORTANT* Go to the TCP/IP settings for the advanced network connection and setup a range of IP addresses in the same subnet as the active interface attached to the WM6 device (run ipconfig to determine). Make sure that 'clients can request their own IP address' is unchecked. Make sure this range falls outside of the IP address assigned to the guest interface from the WM6 device.
5. On the host Mac, create a new VPN connection (PPP) and set the host to the private IP address assigned to the guest (again, you can determine that through running ipconfig on the client). *IMPORTANT* Go to the advanced settings for the VPN connection on the Mac and set the DNS to point to the IP address of the router of the guest WM6 device interface.
6. Connect to the VPN from the Mac host and you should be off and running.
It works flawlessly with very good speed (relatively speaking) over the 3g connection. To get online in a pinch, now I just need to fire up the guest (which takes just a couple of seconds from a saved state), connect my device via usb with internet sharing started, and then connect to the vpn from the Mac.
What is the method for configure the remote desktop program on this device.?
The computer you want to control needs to be XP professional, W2K professional, Vista business or ultimate, or one of the various windows server versions.
On the computer, right click My Computer, select properties, go to the remote tab (on vista select Remote Properties on the left).
Select Allow remote connections.
If you're running a Home version, then as you're not a business user, you are deemed to not need this business function.
Look up RDP and MSTSC in google.
1)configure allow remote desktop connection as described in above post
2)now how is ur pc connected to net?
its recommended that u should not be behind firewall and ur pc should be directly connected to internet with its own ip and make sure ur antivirus firewall is also preferably disabled
3) today's dsl service providers usually allot dynamic public ip adresss to pc so just click the properties of ur dail up broadband connection and note down ur ip adress ( dsl modems are usually always online connection you have to check and modify ur dsl router settings to bridge connection mode and create a dail up connection on desktop ;before modifying any setting in dsl modem make sure u have ur username password for dsl connection and have a back up of dsl router settings)
4)just note down ip and write it in computer box in remote desk top connection in ur handheld
in username field put ur pc user name
in password field put ur pc password
5)just press connect hopefully its done
but some times it really sucks......
Definitely make sure you're behind a firewall! You usually are with your asdl router.
Open port 3389 and forward it to your PC.
For extra security, you can configure your PC to listen on a different port, and configure the router to use that of course.
As commando0 says, you're most likely to have a dynamic IP address, meaning whenever your router connection drops, you'll more than likely get a new address from your ISP, so do get around this, you can use dynamic dns (check dyndns.org).
So use your dyndns address to connect via the internet, and your PC's name for when connecting at home via wifi.
xaccers said:
Definitely make sure you're behind a firewall! You usually are with your asdl router.
Open port 3389 and forward it to your PC.
For extra security, you can configure your PC to listen on a different port, and configure the router to use that of course.
As commando0 says, you're most likely to have a dynamic IP address, meaning whenever your router connection drops, you'll more than likely get a new address from your ISP, so do get around this, you can use dynamic dns (check dyndns.org).
So use your dyndns address to connect via the internet, and your PC's name for when connecting at home via wifi.
Click to expand...
Click to collapse
hi i forwarded port 3389 to my pc (192.169.1.5)
enabled the firewall to listen to that port,
enabled remote connection on vista
but its still not connecting.. i tried using my external as well as lan ip.. nothing seems to work
btw, yes ive been connecting using wifi
anyone uses logmein on here??
Just to confirm, what version of Vista are you running? Business or Ultimate?
On the remote tab of System properties, make sure you've selected "Allow connections from computers running any version of Remote Desktop (less secure)"
Click the "Select Users" button and make sure it says your username already has access, if not, add your username to the list.
Once you've done that, open a cmd window and type:
telnet localhost 3389
then press enter and you should get a blinking curser.
That means your computer is accepting remote desktop connections.
Hold down ctrl and press ] then at the prompt type exit to close the telnet session window.
Then try from your phone.
Logmein.com works perfect over the internet to connect to your pc from a WM device, realy fast and smooth and you can customise the display settings to maximise your speed and refresh rate. 100% recommended
The best use I ever had with Logmein was using it with my HTC Universal, it was so good having VGA and a qwerty keyboard.....
I remember once sat in a pub I needed a file from my PC at home ASAP (to settle an alchole fueled argument, lol), I connected within 30 secs and E-mailed the file to my phone from home. Amasing, also works with any windows OS, I have been using it for about 4 years and its still 100% free.
I'm having issues trying to share my tethered connection with Windows 10 Internet connection sharing. This seems to work just fine on my 2 windows 7 machines. After I had set up ICS on windows 10, The correct IP address shows up with DNS information on my LAN, however It says it has no internet connection when tether is connected. Could this be a result of the using using Win-32 adapter? When I check the other devices on the network, they don't even seem to be getting an IP address. The LAN adapter has the default 192.168.1.1 and is connected to a network hub (not router).
https://forum.xda-developers.com/ge...d-tether-fix-windows-10-t3598634#post76318015
hello check out my thread it will fix it for sure!