I am in need of the pinnout on the main board,
Replaced the charge port to no avail.
Original port not damaged, maybe circuit fail?
Thank you guys.
Related
Hi guys, I'm having problems charging my ms2.
seems that the connector has slowly deformed due to extensive use and it now does not hold the cable properly anymore.
Any suggestion how I can fix this without breaking the usb port? Maybe try another micro usb cable with better fit?
hi,
i´ve got a problem with my galaxy s3 neo. after using it 1 1/2 years, it´s not charging anymore... or - it is charging, if i put some pressure on the usb cable when connected. so i think it´s the usb connector, may i be right?
with my galaxy note 2 that´s not a big problem, because the usb connector is on a seperated board and can easily be replaced. after some research i found out, that the galaxy s3´s usb connector is soldered directly on the motherboard - so it´s not that easy to replace it. but i´ll give it a try...
so my actual question is: does someone know if there is a difference between the spare part usb connector for the s3 and the s3 neo? because i can find one for the s3 easily, but not for the neo.
thanks for your help,
regards b0sse
Hello Guys, I have a Note 4 here, which had two seconds contact with clear Water. The Screen and the Camera broke. I've tested the function of the Phone with an MHL Cable and i've got a Picture, so I ordered a new Screen/Camera and replaced it.
The Phone is working without any Problem excluding the USB Connectivity. I can charge my Phone without any Problems but I cant connect it to any PC. I've tried 6 Cables on 3 PC's and 1 Tablet but it is only charging.
I activated the Dev Settings, switched from Charging only to MTP back and forth and I get still no Notification in the Status Bar.
My USB Stick with Mini USB wont be detected either.
So I ordered a new Charging Port Flex, connected it with the Mainboard, attached a USB Cable to it but still nothing.
The Phone is charging without any Problem, only USB Connections are broken. Is it the Android 6.0.1 Update or the Mainboard broken?
Sorry for my bad English, it isnt my native Language.
Edit : Odin Mode isnt working either, so I think its a Mainboard fault.
Guys? :/
Push?
Could someone please reply with something like : yo, your Mainboard is broken, rip.
Yep, done that right after the Water contact.
If it's not the motherboard it could be a dead short between pins 2 & 3 on the USB.
I replaced the whole USB Board with Flex.
Rip Note 4? :/
Hello everyone,
Currently i have a problem with my samsung tab A 8.0. Days ago i accidentally dropped my tab while it was being charged, resulting in red Cross with lightning icon while i tried to plug it on anything, and suddenly all of my usb otg were not detected and it was not detected on my pc...even usb debugging was not detected too...i had opened its case and checked the continuity of its micro usb port and it still seemed ok...now i have no idea about how to solve this, do you know what to do if something like this happens?? I suspect its pcb track is broken so maybe i will need a new motherboard again...
Hello, anyone?
How are you checking continuity? You would need to check it between the end of the USB cable and the solder points behind the micro USB pins. No point in testing to the actual pins.
The pins that solder to the board are extremely small and difficult to resolder, some sort of magnification is really required.
The way I do it is by using a solid conductor wire wrapped around the end of a decent soldering iron. Even then it's a difficult task and requires a steady hand.
Hi folks,
I'm trying to fix my old Nubia with a broken USB port by bypassing the port.
Since it's soldered to the motherboard, it's almost impossible to solder right on the usb pins.
But I've noticed testpoints, and found the VCC one, on which I soldered a wire. another being soldered to the outside of the port for grounding.
I thought I would be able to charge it that way, but it's not showing any signs of life (with or without the battery)
So I have 2 questions:
-can I charge through the testpoints ?
-do I need to send a signal to the ID pin ? (I guess not, I opened up a charge only cable and it had only 2 wires)
Pic of the connector
I tried charging it with a lab psu and an Aukey Quickcharge 2 charger
Thanks for your help