Related
Only fresh flashed bootloader locked XT1058 AT&T - ROM LPAS23.12-21.7-1, and XT1060 VZW - ROM LPAS23.12-39.7-1 are supported!
See archive content for instructions. Time to install ~20 min. If you experience problems after Android boot, like not working buttons or quick settings, wipe cache + data partitions. Don't update SuperSU (disable auto updates), it won't work. Later I'll post complete debloated ROMs with fresh SuperSU version, and simplify instructions. Be informed also, that this method doesn't give you read-write rights like unlocked bootloader. You may read and write having root-rights, but only till a restart or shutdown occurs, and every change will be undo by the Qualcomm protection (like HTC' s=on).
At the moment patch includes:
SuperSU 2.65 Free
Xposed Framework v86 (installer, modules)
Busybox 1.25.0.YDS, path /system/xbin/busybox
Download
P.S. Install only on indicated above ROM versions, and it's obvious that you must have enough theory knowledge and practical experience to make use of 9008 patch, so I'm not responsible for any consequences, etc. Greets go to: CrashXXL (method inventor), Sabissimo (our former OP), and serg_gangubas (ROM guru).
==============================================================================================
31.07.2017 - Full ROM Patch for Bootloader Locked Moto X ATT/VZW/etc
Based on the same principle, and not depend on system partition content, so it suits any bootloader locked Moto X Gen1 ATT/VZW (possibly any model, besides 1049 RepW / 1055 US Cell), but takes about 4 hours to be done - prepare for that, 100% battery level only!
This full ROM patch includes:
SuperSU 2.82 Free
Xposed Framework v87 (installer, modules)
Busybox 1.26.2, path /system/xbin/busybox
ViperFX 2.5.0.5 - sorry needs polishing, removed now (
Gallery and Camera not depend on Moto services
Gboard instead AOSP Keyboard. If it eats too much RAM, see Simple Keyboard
GAPPSes updated. Use command like adb shell pm uninstall --user 0 com.blahblah.blah to block any unwanted app or service
ES File Explorer Free Edition (a clone, you can disable and install yours )
"Jedy" gesture
AdBlock support (effect lasts till the 1st reboot yet, I'll think about make it constant). Please, choose /data/hosts instead of /system/etc/hosts
ROM debloated, but not deodexed.
Download
Instruction
Be careful, phone will be WIPED then flashed in 9008 "brick" mode (CrashXXL idea). Before you start install Moto drivers, latest RSD Lite, and fully charge the battery.
1) Download and unpack zip on С: (or any), open Python27, launch RUN_path.bat (needs to be launched only single time), install driver QHSUSB_driver.exe, and launch file _Moto.X.BootLocked.*.exe (where * - is desired ROM).
2) Go into fastboot mode, execute RUN_blbroke.bat. Screen gets black, Device Manager in Windows finds "QHSUSB_DLOAD", and installs it as "Qualcomm HS-USB QDLoader 9008 (COM*)". If it doesn't install, google for Windows driver digital signature disable.
3) Now launch RUN_root.bat, and see that patching process took start.
4) A small patch *SPEAKERS.BOOST.exe (if exists) boosts both speakers' volume.
P.S. Please, don't flash anything extra into the phone. In case of trouble, all you need is inside this folder. Just make it work.
To make "Battery OK" in fastboot use fastboot_cyclecharge.bat
Completely drained out battery causing "USB input device" needs disassembly of the phone to charge externally.
In case Titanium Backup shows error "Batch backup interrupted: insufficient free storage space", delete default backup folder, and make a new:
Titanium Backup > Menu > Preferences > Backup folder location > Storage Provider > DocumentProvider storage > Show Internal Storage > Internal Storage > Select Internal Storage > Create the folder > Use the current folder. Done!
Notes for myself: Viper, force wipe, readme.txt, volume patch, Adblock, advanced debloat
Debloated, rooted, lightweight ROM - soon! )
PUBLISHED. Sorry, took long time.
As soon as I can actually get 5.1 flashed I'll try this.
Though I'm afraid I'll have to try to go to stock and use sunshine first, still have a locked BL.
But this is great, I didn't expect root so soon.
DownTheCross said:
As soon as I can actually get 5.1 flashed I'll try this.
Though I'm afraid I'll have to try to go to stock and use sunshine first, still have a locked BL.
But this is great, I didn't expect root so soon.
Click to expand...
Click to collapse
This method is working on locked BL.
DownTheCross said:
As soon as I can actually get 5.1 flashed I'll try this.
Though I'm afraid I'll have to try to go to stock and use sunshine first, still have a locked BL.
But this is great, I didn't expect root so soon.
Click to expand...
Click to collapse
Wait wait... If you can have now possibility to unlock bootloader - go for it immediately! You will have normal FULL root-rights (SuperSU 2.49). Don't install 5.1, if you plan to unlock, because Sunshine app (25$) works only on 4.4.2 Android.
This topic is to help those AT&T users that are boot locked forever (who missed out possibility to unlock on 4.4.2 by proceed to 5.1) to give them READ-ONLY root. Yes, it's limited, but anything at least.
s5610 said:
If you can have now possibility to unlock bootloader...
Click to expand...
Click to collapse
I guess anyone on 4.4.4 today. There is no possibility to use Sunshine anymore.
Anyway spasibo za method
Ahh, if I don't have to be BL unlocked that's great lol.
I haven't read too much into the 5.1 updates or sunshine for that matter.
I've been on krypton 1.4.1 since it was released, and I haven't been able to successfully upgrade to any 5.1 roms yet.
Works great!
Works great for me on Windows 10 RTM 64-bit! Thanks a ton, I was waiting for a post like this.
I only had 3 minor hiccups:
1. RSD Lite gave me an error about "getvar", so I had to go into flashfile.xml in the ROM zip and remove the line that said getvar
2. I had to reboot to disable driver signature enforcement twice for some reason because Windows Update
3. The run-root.bat got stuck on "Executing..." because I installed the wrong driver (the correct file is qcusb.inf when installed from device manager -> browse my computer for driver software -> let me pick from a list -> all devices -> have disk)
Otherwise, everything runs just as well as KitKat, including Xposed.
Hehe got to love step 9
System Write
How can we help in getting the system write to zero using the same method,because I have xt1058 model bootloader unlocked and I provide any file needed to disable the pesky system write...
How can we help in getting the system write to zero using the same method,because I have xt1058 model bootloader unlocked and I provide any file needed to disable the pesky system write...
Click to expand...
Click to collapse
First, never quote op. It takes way to much space and is redundant.
Second, to get write off we would need to some how either start a custom kernel some magical way or disable it via a kernel mod like htc guys did. Another way, which was done before was to burn the efuse but kernel has been patched since then.
Need some help, I did all steps until step 9. I installed the QHSUSB_DLOAD driver manually, and I can see 'Qualcomm HS-USB QDLoader 9008 (COM4)' showed in my Device Manager, but when I run 'RUN_Root.bat', I got this
c:\Python27>python qdloadRoot.py MPRG8960.bin -ptf root/partitions.txt
QDLoad utility version 1.2 (c) VBlack 2014
Found TTY port: com4
Sending MAGIC ...
QCOM fast download protocol targ:
Version: 7
Compatible version 2
Maximum block size 1024 (0x00000400)
Base address of Flash 0x00000000
Flash: eMMC
Window size: 30
Number of sectors: 128
First sector size: 2097152 (0x00200000)
Feature bits: 09
Sending SBL Reset...
Done
c:\Python27>pause
Press any key to continue . . .
Then I tried to run 'RUN_Root.bat' again, then I got
c:\Python27>python qdloadRoot.py MPRG8960.bin -ptf root/partitions.txt
QDLoad utility version 1.2 (c) VBlack 2014
Found TTY port: com4
Requesting Params...
Params:
Version: 8
Min version: 1
Max write size: 1536 (0x00000600)
Model: 144
Device size: Invalid or unrecognized Flash device, or Flash device progr
amming not supported by this implementation
Device type: Intel 28F400BX-TL or Intel 28F400BV-TL
Requesting SoftwareVersion...
Version: PBL_DloadVER2.0
Requesting SerialNumber...
Serial number: 00,00,48,03
Requesting HW Id...
HW Id: 00,00,48,03,e1,10,7e,00
Requesting PublicKey...
PublicKey: 39,c4,ee,3e,b5,be,eb,87,8e,2f,e3,b8,53,4d,14,6f,91,ca,fd,bb,94,2a,0d
,aa,d0,1e,b0,87,62,d4,b9,b8
Uploading file 'MPRG8960.bin' to addr 0x2a000000...
Executing...
Could not find Qualcomm device in Emergency download mode
Done, with errors!!!
c:\Python27>pause
Press any key to continue . . .
any suggestions? Thanks
jahrule said:
First, never quote op. It takes way to much space and is redundant.
Second, to get write off we would need to some how either start a custom kernel some magical way or disable it via a kernel mod like htc guys did. Another way, which was done before was to burn the efuse but kernel has been patched since then.
Click to expand...
Click to collapse
Ill put the files here
Fantastic!!! I was looking this. All the last week I was sleeping about 3 hours per day trying to root my phone.
----
I scream "Victory" before the process finish.
Damn! My phone reboot and stay in the android doll fallen screen.
DejanPet said:
Ill put the files here
Click to expand...
Click to collapse
What to do with these files?
Those files are needed by Jahrule
Sabissimo
Hello.
I did everything as instructed, but eventually got the screen "no command".
The only thing I did not flash rom - a month ago updated by an OTA to 5.1, thought it was not necessary.
Factory reset does not help.
Advise something.
In the end, everything worked, thank you))
It works
It works great! Thank you very much! ATT xt1058.
eze_cba17 said:
Damn! My phone reboot and stay in the android doll fallen screen.
Click to expand...
Click to collapse
Follow the OP instruction EXACTLY, no exceptions!
If you got your current 5.1 through AT&T OTA, it's not enough for root patching procedure. A full RSD 5.1 official SBF flash over is required.
Could someone please do a video on this. I'm having a little trouble.
All developments are carried out thanks to donations on Purchase of these or other devices
thank
Please do not copy files to other file shares
the project is under constant development and refinement
Project name ROM Droid Mini/Maxx/Ultra L!te FW 4-21 ML
Tagline Faster Lighter Economical
SYSTEM Firmware SU4-21 Multilingual
- firmware Deodex - allowing resources using modifiers such GravityBox apply all when firmware odex, it sometimes limited customization or going awry
- tzdata 2015e
- icudt51l last
- return "the gesture of the Jedi" (after installing the firmware of the old sensor /*** it does not threaten the phone)
- delete more apps VZW & MOTO
- replaced by sound WirelessChargingStarted
- old gapps for long work phone
- uppdate apps Chrome, LatinIME, Skip, TouchLess, MotCamera, MotGallery, Migrate
- tetering work
- removed a lot of the background services collect and send data on the type of phone DropBox, MotoCare, MotoConntect, Drive, FaceLock ... etc.
- added Russian, Ukrainian language
for Unloked Device
Install for Custom Recovery
Root not PreInstalled
Download there https://yadi.sk/d/jp8ykQqFindY8/Droid
for Loked Device
Install for QDLoad9008
Root, Xposed, BusyBox is PreInstalled
- Root SuperSU v2.46
- XPosed 2.6.1
- BusyBox v30
DISCLAIMER
Author is not responsible for totally bricked devices, broken arms, legs, plane crashes and your wife's cheating.
All actions taken is your own risk.
Instructions to install
You:
- shouldn't be afraid of Qualcomm HS-USB QDLoader 9008;
- do not change any files, pathes;
- can install drivers manually;
- need to install python-2.7.9 and pyserial-2.7.win32;
- unzipp _Rus_4_4_4_VZW_SU6-7_BL_V30.BA_Stock.rar to Cython27;
Method is dangerous, however gives results.
you must have firmware SU6-7 receiving is not in the form of an update (OTA) and stitched through the RSD Lite.
00 Flash CFC-obakem_verizon-user-4.4.4-SU6-7-release-keys.xml firmware
01 Unzipp everything to Cython27.
02 Run BLBROKE.bat.
03 After you got Qualcomm HS-USB QDLoader 9008, install drivers manually
04 Run RUN_Rus_Part1.bat. Parts XX of system.
*** You can also run a file if you are sure that your phone can work 4-5 hours with the screen RUN_Rus_VZW_Full.bat
then repeat this step X times (the number of times equal to 6)
while (found next part) do
***
>> fastboot to hold 10 minutes that would have been charged a little phone
>> Run BLBROKE.bat.
>> Run RUN_Rus_Part**.bat. Parts XX of system.
***
end
99 Turn device on. Now you have SU DEODEX PreRooted
installed application Xposed 2.6.1
Xposed launched clicked install, reboot your phone
I see that the application is launched is set app_process 58 (pre-installed in the system) and XPosedBridge.jar 54 version (made with the application)
then uploaded GravityBox [KK], a check mark, the next reboot, and everything works
Drivers, Soft there -> https://yadi.sk/d/p458Cy0XineRC
Scripts, ROM there -> https://yadi.sk/d/kxbxpTnziSg35/Droid/4.4.4 SU4-21
Please do not copy files to other file shares
the project is under constant development and refinement
XDA:DevDB Information
[ROM] Droid Mini/Maxx/Ultra L!te FW 4-21 ML, ROM for the Motorola Droid Ultra
Contributors
CrashXXL
ROM OS Version: 4.4.x KitKat
ROM Kernel: Linux 3.4.x
ROM Firmware Required: Android 4.4.4 SU6-7 (Flash on RSDLite)
Version Information
Status: Stable
Current Stable Version: 1.02
Stable Release Date: 2015-09-01
Current Beta Version: 0.01
Beta Release Date: 2015-08-15
Created 2015-10-08
Last Updated 2015-10-08
Reserved
Reserved
Update Available
Log
- Launcher with a mesh 4 * 5 with no search string
- Smart Action Moto return ... The assistant working all options
for blocked Patch_SmartAction_Launcher.4x5.NoBar.rar https://yadi.sk/d/kxbxpTnziSg35/Droid
for unlocked MotLauncher.4x5.NoBar.zip https://yadi.sk/d/jp8ykQqFindY8/Droid and SmartActions.zip https://yadi.sk/d/jp8ykQqFindY8/SmartActions
Reserved
I'm a bit confused here. A few months ago I used your set of steps to upgrade to SU6-7 with permanent root (even though I still have locked bootloader). Does this new set of steps allow downgrading to SU4-21 and then the ability to use Sunshine to unlock bootloader? Thanks!
Can I do Write Protection with this ROM?
OscarBrito16 said:
Can I do Write Protection with this ROM?
Click to expand...
Click to collapse
Write protection is still enabled so the root is limited as far as what you can do with it.
classic757 said:
Write protection is still enabled so the root is limited as far as what you can do with it.
Click to expand...
Click to collapse
I mean to install a custom recovery or flash a custom rom!
No, you would not be able to install a custom recovery with method. Unless you have su4-21 or lower your bootloader is locked and at this time there isn't a method to unlock it.
Also you can't downgrade to an older su version, once you have su5-24 or above the qfuse is blown.
As said above you can achieve root, but since the system is still write protected root access is limited. The other option is to perm root your device, and try safestrap, I hope I'm allowed to post that in the thread, sorry if I'm not.
Sent from my XT1080 using XDA mobile app
OscarBrito16 said:
I mean to install a custom recovery or flash a custom rom!
Click to expand...
Click to collapse
Without write protection disabled you cannot install custom recovery or flash custom roms.
Also, if you are on 4.4.4 there is no full root available at this time.
any chance to implement/add Czech language on this ROM?
dcoaster said:
I'm a bit confused here. A few months ago I used your set of steps to upgrade to SU6-7 with permanent root (even though I still have locked bootloader). Does this new set of steps allow downgrading to SU4-21 and then the ability to use Sunshine to unlock bootloader? Thanks!
Click to expand...
Click to collapse
I have the same concerns. Are we supposed to downgrade to the SU4-21???Will this grant us the ability to use Sunshine and unlock our bootloaders?? I thought it wasn't possible to downgrade??? Please I'm lost here I want to do this but I'm am unsure of the outcome?
You can add any language, but it takes a lot of time.
can you tell me how to do it?
- unpack apk
- transtale xml value-en to value-cz
- pack
- install on update from twrp
- check work
@CrashXXL
how can I add the gesture of jedi to my phone? what files do I need to take from your rom?
I do not want to take the whole rom, would be great if i could only take a few files and push the diff to my phone
Can i use this to flash it right over my rooted SU6-7 (rooted with your method months ago, Crash) or do i need to re-flash original stock (without root)?
will my phone be still rooted if i factory reset it..?
I guess this contains only Russian and/or English language, am i right?
Einheit-101 said:
I guess this contains only Russian and/or English language, am i right?
Click to expand...
Click to collapse
no, localization saved and added 2 more Russian and Ukrainian
Yeah, so no German
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Welcome to the NitrogenOS Q&A Megathread. Here you can find answers for the most popular problems and questions about NitrogenOS. I started this thread, so that new users don't repeatedly ask the same questions multiple times. While I am fairly new to coding in Java, I can definitely say I know a lot about Android phones and NitrogenOS, but you'll have to trust me on that. If you need any more help, you can even PM me and I'll try to reply as soon as I can.
You can find the original NitrogenOS thread here.
ROM info
Developer: xyyx
Latest Android version: 8.1 Oreo
NOS Download (latest): https://sourceforge.net/projects/nitrogen-project/files/kenzo/kenzo_test/8.1/
Bugs and updates
- A (very) small amount of users reported Google Dialer not working properly while installed through OpenGapps or the Play Store, you can still use stock dialer
1. Test or stable?!?!
Test in this case doesn't mean less stable. xyyx named the two versions a little confusingly.
Test means Oreo (Android 8.0 and 8.1) and Stable means Nougat (Android 7.1.2).
So let's make this a little less confusing:
Oreo (8.0) builds -> Download from here
Oreo (8.1) builds -> Download from here
Nougat (7.1.2) builds -> Download from here
2. Youtube PiP (Picture in Picture mode)
Google has patched PiP a long time ago, so it doesn't work with the latest Youtube releases. The last official release working with PiP is 12.34.55, which you can download from ApkMirror.
My preferred option however is iYTBP (injected YouTube Background Playback), a modified version of Youtube, but it gets a little confusing as there are multiple options.
You can download it from this thread.
Now the tricky part - choosing the right version. I always prefer the Vanced version, which can be found in the 2nd post. Again you have multiple options, but I will not go through all of them since they are explained pretty good in the post itself. While iYTBP enables PiP, it also blocks ads and adds a lot of useful settings and new updates come very frequently. There are multiple installation methods, but I prefer the Magisk one, since it offers options like detaching the Youtube app from Play Store. What this means is, that you don't have to disable auto-updates and it will not bug you to constantly update it.
You can try these methods:
Magisk Module (Easiest):
1. Open Magisk Manager
2. Go to Downloads
3. In the search bar type "Youtube", you should see two results
4. Choose either the normal or the black theme (I personally prefer the black one)
5. Press the download arrow and then "Install"
6. Wait for a while (it's a big package to download and unpack)
7. Reboot
This is by far the easiest option and the module is updated fairly often.
Manual:
1. Delete or uninstall any previous release of Youtube. If you installed it as a system app, disable it or delete the /system/app/YouTube folder. If you had to delete the folder, reboot.
2. Download the Youtube apk
3. Make a folder called YouTube (watch the caps!)
4. Move the apk to this folder and rename it as YouTube (again with the caps)
5. Copy/move the folder to /system/app (The directory should look like this: /system/app/YouTube/YouTube.apk)
6. Reboot
Magisk (manual):
1. Download the Youtube apk, the iYTBP universal installer and the use_this_settings.sh file. Check that they are in the downloads folder.
2. Edit the use_this_settings.sh file if you want. Since we're installing from Magisk, you'll need to set MAGINSTALL to YES (MAGINSTALL="YES"). I usually also enable detach (DETACH="YES"). This will make the Play Store think Youtube isn't installed and it will not bug you for updates.
3. Open Magisk Manager, go to Modules and press the + button. Now select the universal installer zip and flash it in Magisk.
4. Reboot
Recovery method:
Same as for Magisk, but MAGINSTALL is set to NO (MAGINSTALL="NO"). In case you didn't read the Magisk method, here is the recovery method...
1. Download the Youtube apk, the iYTBP universal installer and the use_this_settings.sh file. Check that they are in the downloads folder.
2. Edit the use_this_settings.sh file if you want. I usually enable detach (DETACH="YES"). This will make the Play Store think Youtube isn't installed and it will not bug you for updates.
3. Reboot to recovery, go to Install and choose the universal installer zip, flash it.
4. Reboot
If you open a video in fullscreen mode and press the home button, it should open it in PiP mode. If you want to change some advanced settings, you can go to your Account (the round icon with your profile picture) -> Settings -> iYTBP Settings
3. Goodix & FPC - What are they
Goodix and FPC are two different types of fingerprint sensors (or rather sensor manufacturers). They both work in Android 8.1 builds. Custom kernels or mods may break the fingerprint sensor functionality.
4. Rooting
tl;dr: rooting NitrogenOS is the same as rooting any other custom rom, just flash Magisk, SuperSU, phh's superuser or anything else.
Now for the extended version.
Magisk:
Magisk is a great open-source root manager, developed by topjohnwu. It features a feature rich app, but most people prefer it because of it's "modules", packages which can do a bunch of things, from installing apps like Viper4AndroidFX or Dolby Atmos, to modifying system settings, like the volume steps increase. Magisk also features an option called "Magisk Hide", which can bypass Android's SafetyNet.
Check out the Magisk thread.
You can directly download the latest version of Magisk from https://tiny.cc/latestmagisk
SuperSU:
SuperSU is an alternative root manager. It used to be developed by Chainfire, but has recently been purchased by another company. I still prefer Magisk, but SuperSU is a great alternative for new users. My problem with it though is, that it is not open-source and the new buyer is pretty secretive so I don't really trust them.
Check out the SuperSU website for the download link.
phh's SuperUser:
Another open-source root manager, but the great thing about this one is, that it's very minimalistic and very small in size.
Check out the SuperUser thread and phh's Build Bot.
5. Google Apps (gapps)
Google apps are a vital part of custom roms. You might not know this, but AOSP and CM based roms are made from Google source code. Google actually makes Android open-source, but the Play Store and other Google apps are not. That's why roms like NitrogenOS do not come with the Play Store preinstalled. That is where Open Gapps come in. They are prepackaged apps, updated almost daily. They come in various sizes and versions, but they can all be flashed in TWRP like a normal zip file.
Platform: arm/arm64/x86/x86_64 - RN3 has an arm64 processor (Think of it as a 64-bit CPU for phones)
Android: 8.0/7.1/7.0... - This is the android version, NOS is Oreo based so choose 8.0 (Or 7.1 for Nougat) [Check below for OpenGapps 8.1]
Variant: This is where it gets complicated. There are a LOT of versions to choose from. For more in-depth resources check the OpenGapps' package comparison.
But OpenGapps are a lot more customisable, to the level where you can choose individual apps you want installed. The easiest way to do this, is to flash the Aroma package, which enables you to choose exactly which packages you want installed. Another option is to configure any of the selected packages using a gapps-config.txt file. You can learn more about that in the Advanced Features and Options section.
You can download daily builds for any Android version from https://opengapps.org/
6. TWRP (Recovery)
A recovery is a partition, used to flash files like ROMs, gapps and any other modifications. You do (in most cases) need an unlocked bootloader to use it. Unlocking your bootloader will not be described on this thread, as there are a lot of resources for our device.
Official TWRP - This is the official TWRP (Team Win Recovery Project) for our device
You can find the latest updates for TWRP on their website.
Red Wolf - This is a modified version of TWRP, my absolute favourite because of it's custom features.
Flashing TWRP:
If you don't have a custom recovery installed and you have unlocked your bootloader, then download the latest version of your preferred recovery and follow these steps:
1. Download Minimal ADB and Fastboot on Windows, or use sudo apt install android-tools-adb android-tools-fastboot if you're on Linux.
2. Enable USB Debugging (Settings -> About phone -> Press "Build number" 7 times to enable Developer options). You should find the Developer options in settings above "About Device". Find USB Debugging and enable it.
3. Connect your PC to the phone via a cable. Open Minimal ADB and Fastboot (which will open CMD) or Terminal on Linux and type this (same for both OSs): adb devices. Select "Always allow on this computer" and confirm access on your phone.
4. Reboot your phone to fastboot/bootloader (By holding Power and Vol-, releasing the power button after a vibration and holding the Vol- button until you see the Xiaomi mascot).
5. Type (In CMD/Terminal): fastboot devices, to confirm if the phone has been recognised, then fastboot flash recovery /path/to/recovery.img
6. After it has succesfully finished, remove the cable and reboot directly to recovery (Power and Vol+, release power after vibration, but keep holding the Vol+ button until you see the TWRP or RedWolf logo).
If you do already have a custom recovery installed and just want to update it, flash the .img or .zip file in your already installed recovery and select "Reboot to recovery".
7. NOS asks me for a password after flashing?!!?!?
This is actually not NitrogenOS's fault, it's a byproduct of your previous rom, most often MIUI. What this means is, that your internal storage is encrypted and the only way to fix this, is to backup everything on your internal storage, which you can do by connecting your phone to your pc while in recovery. You should be able to access the phone's storage and move the files from there. If you for some reason can't do that, you can still put in an sdcard and copy the files to it in TWRP. Bottom line, backup the files and then go to "Wipe" and find the "Format data" button. You might see a "wipe data" button, but this is not the same. When you "wipe data" you are wiping your system, cache, dalvik cache and data partitions, but formatting data will format your internal partition as well and thus remove the encryption.
You can finally reflash NOS and gapps or whatever other modification you want.
8. Firmwares
Check out this link to download the latest firmware for our device.
What is firmware? - It's what connects hardware to software (don't confuse it with a kernel). It's what, for example, makes the camera work.
Do I really need firmware - Yes (but it's already installed, even after completely wiping the stock rom, since it's on separate partitions).
Do I need the most up-to-date firmware - Actually no, the only difference you will notice is in the signal and WiFi strength. If yours are good enough, you don't need to update, otherwise feel free to download the newest version from the link above.
What is emmc_appsboot.mbn? - It's a bootloader update. Bootloader or fastboot is the partition in which you have unlocked your bootloader and flashed the recovery. If you have officially unlocked your bootloader, then you can flash firmware with emmc_appsboot.mbn, but if you have unofficially unlocked your bootloader, do not flash these files as they will re-lock it. But you can still flash the version without emmc_appsboot.mbn.
Kenzo? Kate? - Kate devices are the same as kenzo ones but are a little bigger.
Some comparisons:
Kenzo
Size: 150 * 76 * 6.85 mm
Weight: 164g
Kate
Size: 152 * 76 * 6.85 mm
Weight: 167g
Model numbers:
Kenzo: 2015116
Kate: 2015161
Kate devices are 32/3 GB, and some kenzo devices are as well (some are 16/2 GB), not really sure about this part.
Global stable or developer? - Most people use developer roms, but again, this is not the actual ROM, just the firmware extracted from the rom, it doesn't really matter which one you choose.
When do I need to flash firmware? - If you're coming from MIUI8 (or 9), then you probably have the newest firmware. In this case you don't need to flash it, because MIUI roms already have firmware included in the update. If you're coming from a CM or AOSP based rom you also probably don't have to flash it, but I suggest you update it just in case. If your signal is good enough though, there really is no need.
9. How to flash the rom
Flashing is pretty straight forward. Just go to the Install section of TWRP and flash it like any normal zip, nothing special.
If you're coming from MIUI, then the full procedure is this:
1. Unlock your bootloader (google it, useless explaining it here)
2. Flash TWRP
3. Make a full device backup (Nandroid backup)
4. Copy or move all important files from the internal storage to an sdcard or your pc
5. Format data, or in other words, wipe EVERYTHING (excluding external storage) - This will delete all your photos and anything else in internal storage
6. Flash the latest NOS "test" build (Oreo)
7. Flash gapps (I recommend opengapps.org, check above)
8. Reboot to system
10. OTA?
What is OTA? - OTA means Over The Air (Update)
Does NOS have OTA? - Actually yes and no, newer updates (from March 2018 on) do have partial OTA (it does check for updates and notify you, while also giving a direct download link to SourceForge, but you will have to manually flash every update in your recovery.
What about incremental updates? - Sorry, but no. You'll have to download full packages every time. If you have a bandwidth cap then just download an update every week or two, you can check the changelog to see if you think it's worth updating to.
11. Google Camera
If you're having problems with the official Google Camera or just want some added features then look no further than modded camera apps. Check out this thread by emime12, it's very frequently updated and features a lot of different camera mods, including Google Camera, MIUI Camera, MOTO Camera and many more.
Recommended settings:
3x3 Grid - For better photos
I usually disable "Save location" and "Camera sounds"
Model: Pixel XL (corr) - default
Config camera HDR+: NEXUS 6
HDR+ parameters: Default
Panorama resolution: High
Advanced: Enable both
Experimental: I usually leave this disabled but it's your choice.
Back camera video resolution: UHD 4K (30 fps)
In case your camera doesn't work check if you have these two files and delete them:
/System/framework/com.google.android.camera.experimental2016.jar
and
/System/etc/permissions/com.google.android.camera.experimental2016.xml
Credits go to: @emime12 and Njaiker.
You can find more info about problems and updates on emime12's thread.
Settings may differ a lot, so check emime12's recommended or just test until you find ones that work for you
12. RAM Management - Low free RAM
Android's RAM (Read Only Memory) management doesn't work like Windows'. Android manages RAM very well, "Free RAM is wasted RAM" is a very common expression on XDA. Android loads the first couple of apps into the RAM and priorities the open one. More used ram means more apps loaded in ram which means faster load times. Don't worry about it too much and just enjoy the fast loading speeds.
13. VoLTE?
VoLTE should work on Android 8.1. Magisk, Viper or any other mods may break it.
14. Custom kernels
While there are a lot of custom kernels, I suggest you stick with the stock one, as it is made specifically for NOS and thus it is the most stable. If you still want a custom kernel, you can try Radon or Agni but they might break VoLTE or your fingerprint sensor.
Agni XDA Thread - By psndna88
Radon XDA Thread - By Umang96
15. Daily driver or not?
Yes, NitrogenOS Oreo is very stable, definitely enough for a daily driver. It is the best Oreo rom for our device (in my opinion), as it offers just the right amount of customization and stability.
15. GPS
Some users have reported low accuracy, but you should be fine if you turn on High Accuracy mode and/or install Faster GPS.
Update: In recent updates GPS shouldn't be a problem anymore as xyyx has fixed it, but some users have still reported low accuracy.
16. Viper4Android FX
(There may be other ways, but I haven't tested them yet so I can't confirm if they work) By far the easiest way to install Viper4Android FX is using Magisk. There is Magisk module called ViPER4Android FX Materialized. Download and install that module from the Magisk repo, choose your preferred installation option (By pressing Vol+ or Vol- to select which version you want installed and if you want it materialized - for newest materialized version press Vol+ 2 times) and finally reboot. Try playing some music and open the Viper app. Turn on the "Master Power" switch and the "Playback Gain Control" (the easiest way to tell if it worked). If after a little time the volume increases, it means that Viper4Android FX works. If not, press the three dots and choose "Exit" (without turning off the master power or gain control). Now open the app again and it should work. You can also check that in the side menu under "Driver status", if it's enabled and processing, then everything works.
You may or may not have to exit and re-enter the app after reboot to enable processing (in my case I had to).
I would show you my recommended settings (as requested), but to be honest I only use:
Headset
Viper Bass (Natural bass, 40 HZ frequency, 8 dB)
Viper Clarity (Natural, 6 dB)
Sometimes I use Field surround with default settings
Phone speakers
eXtra loud (Slight, 4x max gain, -1.9 dB max output)
Bluetooth device
Playback gain control (Moderate, 6x max gain, -1.9 dB max output)
If I'm at a party with my bluetooth speaker I pump it up to Extreme and 8x max gain
Viper Bass (Natural, 40 HZ frequency, 8 dB), 17 dB for parties
Viper Clarity (Natural, 3.5 dB)
I don't use equalizers or if I do, they are song-specific. I also don't USB/Dock, so I can't recommend anything there.
Of course these settings can vary depending on the song, so choose those, which you like the most and don't stick with just those I chose, try all the functions to see which you prefer.
17. AdAway (Root)
AdAway is a great open-source root ad blocker, which can automatically download and update sources and works by adding those to the hosts file. It work well on the internet, but also inside apps (most of the time).
Check out the official AdAway website. You can also download it from F-Droid.
Adaway v3.2 (60) (direct download link)
Adding custom host sources:
Go to "Host sources" and add your own sources or check out these: AdAway's host sources
Be careful when adding all of them, since some can block legitimate links like goo.gl.
AdAway also offers an option to scan for Adware, which can be found under "Scan for adware". This will bring up a new window, press "Start scanning". If you don't need/want the mentioned apps you can uninstall them, but AdAway can't block their ads.
You can also check out my recommended settings:
wow,really appreciated that sir., it is very helpful specially for those who wanted to try, flashing rom or any mods on their device like me. thanks and keep up the good work sir God bless!
i think i can add up little bit here.
1) u r on miui & u want to flash nitrogen so u go to recovery and backup ur current rom in case if u dont like nitrogen u can restore back to miui with all ur setting & app. now assume u r on nitrogen, after 4-5 days u dont like nitroge & u decided to come back to miui, so u go to recovery and restore yr backup that u have taken earlier. after success booting the screen with pin or password will appear. so u would enter/guess any previous password, pin u used earlier but it will not open. here the real problem come. i have also faced same issue & got upset searching endless solution on google . u will get mad on u. security bypass will also not work. after spending endless hour i come with solution. download aroma zip search on net. flash it through recovery this will help u to get in system its ike file manager. then head to data, system and delete all file u see below
locksettings.db, locksettings.db-shm, locksettings.db-wal, gatekeeper.password.key, gatekeeper.pattern.key
and then restart, yr problem would be solve.
2) nitrogen os does not support video calling via jio. none custom rom other then then miui support.
3)xposed is not available for oreo.
4)i have used nitrogen oreo for about 2 weeks it is stable but not as miui. some time r net would not work, jio call drop, lagging u have to restart on every time u faced problem. i suggest that wait for some time to roll out nought port for kenzo with zero bug & this will happen soon.
saifuk said:
i think i can add up little bit here.
1) u r on miui & u want to flash nitrogen so u go to recovery and backup ur current rom in case if u dont like nitrogen u can restore back to miui with all ur setting & app. now assume u r on nitrogen, after 4-5 days u dont like nitroge & u decided to come back to miui, so u go to recovery and restore yr backup that u have taken earlier. after success booting the screen with pin or password will appear. so u would enter/guess any previous password, pin u used earlier but it will not open. here the real problem come. i have also faced same issue & got upset searching endless solution on google . u will get mad on u. security bypass will also not work. after spending endless hour i come with solution. download aroma zip search on net. flash it through recovery this will help u to get in system its ike file manager. then head to data, system and delete all file u see below
locksettings.db, locksettings.db-shm, locksettings.db-wal, gatekeeper.password.key, gatekeeper.pattern.key
and then restart, yr problem would be solve.
2) nitrogen os does not support video calling via jio. none custom rom other then then miui support.
3)xposed is not available for oreo.
4)i have used nitrogen oreo for about 2 weeks it is stable but not as miui. some time r net would not work, jio call drop, lagging u have to restart on every time u faced problem. i suggest that wait for some time to roll out nought port for kenzo with zero bug & this will happen soon.
Click to expand...
Click to collapse
Thanks for the tip, will update the thread.
@JustMeErazem volte on 2nd sim works well. I myself use it. After flashing magisk just v need to hide root from all system apps to make sure volte works flawless even after reboot. Plz edit it in the description. I hav been using nos since many time so with experience i am giving my feedback. Thanks?
@saifuk what kind of nougat port u are expecting of ?
Aditya1011 said:
@JustMeErazem volte on 2nd sim works well. I myself use it. After flashing magisk just v need to hide root from all system apps to make sure volte works flawless even after reboot. Plz edit it in the description. I hav been using nos since many time so with experience i am giving my feedback. Thanks
Click to expand...
Click to collapse
I haven't rooted my phone, VoLTE still not working.
---------- Post added at 03:37 PM ---------- Previous post was at 03:34 PM ----------
@justmerazem Change VoLTE point again to previous. I installed NOS on mine & my other two friends' phone. They've not used magisk or superSU nor me. But VoLTE doesn't work on 2nd Sim for us.
AtomR said:
I haven't rooted my phone, VoLTE still not working.
---------- Post added at 03:37 PM ---------- Previous post was at 03:34 PM ----------
@justmerazem Change VoLTE point again to previous. I installed NOS on mine & my other two friends' phone. They've not used magisk or superSU nor me. But VoLTE doesn't work on 2nd Sim for us.
Click to expand...
Click to collapse
Flash latest firmware of developer rom. And volte is sure shot working.
Aditya1011 said:
Flash latest firmware of developer rom. And volte is sure shot working.
Click to expand...
Click to collapse
Mate, I'm already on 7.9.22 firmware. Lots of people are reporting it. Yours is working, must be some kind of random.
@Aditya1011 Mate, what happened? No reply? Huh. Latest firmware. No magisk, no any kind of root. No sound mod. Still Volte not working on 2nd Sim on 3 different Kenzos.
@JustMeErazem Please include in your post that VoLTE is indeed buggy.
how to install via dualboot patcher as secondary rom?
AtomR said:
@Aditya1011 Mate, what happened? No reply? Huh. Latest firmware. No magisk, no any kind of root. No sound mod. Still Volte not working on 2nd Sim on 3 different Kenzos.
@JustMeErazem Please include in your post that VoLTE is indeed buggy.
Click to expand...
Click to collapse
Idk bro y that happening to u. Flash miui EU rom n thn the nos rom. Mayb that should work.... Bcuz I had done that for the 1st time whn my volte wasn't working at any cost. Best of luck.
smjhh said:
how to install via dualboot patcher as secondary rom?
Click to expand...
Click to collapse
I don't think dual boot patcher supports oreo roms. Try asking on their thread to see if it does.
Google HDR camera 5 or 5.1 work with this ROM??
sagar13190 said:
Google HDR camera 5 or 5.1 work with this ROM??
Click to expand...
Click to collapse
Read op!
I tried google HDR camera v5 n v5.1 on lineage Oreo, MAOSP Oreo nitrogen Oreo ROM bt its not working...bt in ROM based on nogut 7.1.2 its work great
sagar13190 said:
I tried google HDR camera v5 n v5.1 on lineage Oreo, MAOSP Oreo nitrogen Oreo ROM bt its not working...bt in ROM based on nogut 7.1.2 its work great
Click to expand...
Click to collapse
It works for many users. Did you flash my zip or install an apk?
Sim card detection issue
Sometimes nitrogen os Oreo does not detect sim cards after reboot so I changed ROM and installed aosp extended. I know that Xyyx has already mentioned this as bug. Due to this bug it is not daily driver. Hope xyyx will fix this as soon as possible. If you have solution, please share it.
dhavalmehta said:
Sometimes nitrogen os Oreo does not detect sim cards after reboot so I changed ROM and installed aosp extended. I know that Xyyx has already mentioned this as bug. Due to this bug it is not daily driver. Hope xyyx will fix this as soon as possible. If you have solution, please share it.
Click to expand...
Click to collapse
Dude, it's really not a big problem, it detects it like 95% of the time. Just reboot and you're done. Or wait about 2 min and it should detect it. You could also just remove the sim and reinsert it. But since the latest few updates for me it gets detected 100% of the time. So update to 28/10/2017 build and you should be fine.
@JustMeErazem You're giving flase info. to others saying that VoLTE works on both sim. Actually, it works only on first sim. Tried, tested on 3 different Kenzo's. Clean flashed.
Conclusion: VoLTE doesn't work on 2nd sim.
I guess global version will come within 2 days.
http://www.oneplusbbs.com/forum.php?mod=viewthread&tid=3876301&mobile=2
Step by Step Guide - Android 8.0 Chinese beta. Clean/dirty flash lock/UL BL.
Hello Guys,
To make things easy heres a step by step guide to install the chinese oreo beta on locked/unlocked Bl for the 5T
So I got my hands on the android oreo chinese beta (H2OS) and flashed it on my oneplus 5t which was on a locked bootloader and running stable 4.7.6 with star wars theme enabled. Here's a step by step guide to install H2os Oreo beta rom wtihout losing any data.
WARNING : BACKUP - BACKUP - BACKUP and flash at your own risk. I would not be responsible for any loss.
METHOD 1 : FOR LOCKED/UNLOCKED BL BUT WITH STOCK RECOVERY
1) Download the rom from this link : https://goo.gl/4nPrxx
2) Ensure you have backed up all your important data and make sure you have atleast 50% battery.
3) Copy the downloaded zip to phones internal memory (make sure its in the main directory and not in any folder.
4) Go to settings > system updates > top right hand corner tap the settings icon > tap local upgrade > tap on the downloaded file > tap update now and wait for it to finish installing the update. ( first boot will take 8 to 10 minutes so please dont panic.
5) Once first boot is done you may have a force close for 1 or 2 apps just uninstall them and reinstall from the play store and you are good to go. Also star wars theme continues to work and all basic functions work as expected.
6) If you want a clean install or having many force closures please perform a factory reset and everything should be resolved.
https://forum.xda-developers.com/oneplus-5t/how-to/step-step-guide-android-8-0-chinese-t3726772
Yup, I'm downloading now. This should be fun.
Mike02z said:
Yup, I'm downloading now. This should be fun.
Click to expand...
Click to collapse
When you're done, can you tell us what exactly has changed? I went to the chinese page, but google translator wasn't so helpful tbh.
devil188 said:
When you're done, can you tell us what exactly has changed? I went to the chinese page, but google translator wasn't so helpful tbh.
Click to expand...
Click to collapse
This update ushered in based on the new Android O (8.0) hydrogen OS
【desktop】
- Optimized application shortcut menu
- Integrate icon options with app shortcuts
- Shot on OnePlus Add photos upload function
【system】
New shortcut settings panel design
- Android O new features, including but not limited to:
****1. Add Picture in Picture function
****2 new auto-fill (Auto-Fill) function
****3 new smart text selection (Smart Text Selection)
- Update Android system patch
Known Issues
1. WeChat fingerprint payment can not be used temporarily
2. Third-party applications may not compatible list, please download the attachment compression package. Android O may not be compatible with the application list. Rar (25.83 KB, Downloads: 364)
This a translation of the update. I used g translate. :good:
It seems to run OK. Obviously some stuff is still in Chinese. I tried to flash TWRP and TWRP booted but even after a clearing cache/Div the ROM then would not boot. I just got a white light.
For initial install I did a complete data format then loaded the stock recovery ,and the latest stable OOS, then flashed the Chinese O.. You do need to pull a PlayStore .APK and reload all the Google apps after a flash.
Unless this one is different than the one they have on their main site, it's not Oreo. I flashed it, tried flashing Gapps and Gapps said I had to flash appropriate Gapps for 7.1 :/
Very nice. Thanks for the write-up!
Already open beta 3 now.
Hey guys.
I am using magisk 15.3 to debloat the v29a system systemlessly.
Systemless Debloat with the magisk module (terminal debloater) means that the system partition isn't touched!
Hence, it don't breaks safetynet (also with the help of Universal safetynet fix beta 5).
Requirements:
BL unlocked
TWRP installed, up and running
Here is a short how to guide:
When you already on v29a and you have modify the system partition (adaway, supersu, TiBu,...) just flash the stock v29a system partition again and don't touch it (no supersu, no adaway,...)!
Here is the link: https://forum.xda-developers.com/g4/development/h815-nougat-stock-t3659860
Flash magisk 15.3 in TWRP and boot up.
Here is the Link: https://forum.xda-developers.com/apps/magisk/official-magisk-v7-universal-systemless-t3473445
Go into magisk manager and check safetynet status. In my case cts profile fails. No problem...
Go into twrp and flash the universal safetynet beta 5 fix. DONT USE the stable, use the BETA!
Here is the link: https://forum.xda-developers.com/apps/magisk/xiaomi-safetynet-fix-t3600431
Restart phone and check safetynet status. It should pass booth checks.
Now you are rooted and pass safetynet. You can install and use Netflix, Super Mario Run, banking apps... victory
To get adaway working and not breaking safetynet, open it, go to settings and set the hosts file location to /data/. Press update/install hosts file. Adaway will ask you to create a symlink on system. Do it, this will not break safetynet!
From magisk manager you can install "terminal debloater" and use my list to Debloat the rom without breaking safetynet.
Here is the List:
1 - Google Play Books
2 - DRM Service
3 - Docs
4 - Sheets
5 - Slides
6 - GNSS Air Test
7 - gnsslogcat
8 - LG GNSS 2.1
9 - GnssTest 1.2
10 - Google Text-to-speech Engine
11 - HTML Viewer
12 - Hangouts
13 - Hidden Menu
14 - HiddenSIMUnlockMenu
15 - LG Account
16 - LGAirDrive
17 - LG Backup Launcher
18 - LGDrm
19 - FOTA Update
20 - Audio share
21 - LGSmartcardService
22 - Smart cleaning
23 - LGWernickeManager
24 - LteConfigs
25 - Google Play Newsstand
26 - PacProcessor
27 - Google Play Games
28 - Google+
29 - Print Spooler
30 - Use DLNA feature
31 - SmartShareProvider
32 - Google Play Movies
33 - Wfd Service
34 - atfwd
35 - ELTest
36 - ServiceMenu
37 - TalkBack
38 - BackupRestoreConfirmation
39 - LG Health Agent
40 - Cloud
41 - Battery drain info
42 - GCUV
43 - Game battery saver
44 - IceContacts
45 - InCalAgent
46 - LG AirDrive
47 - Clock
48 - App Updates
49 - LG Mobile Switch
50 - Internet
51 - Calculator
52 - Calendar
53 - Cell Broadcast
54 - Smart Notice
55 - Contacts
56 - LGSmartCover
57 - Software update
58 - Email
59 - Exchange
60 - File Manager
61 - FormManager
62 - Answer me
63 - LGInstallService
64 - LDB
65 - LGMapUI
66 - Messaging
67 - Music
68 - Music
69 - LG P2p Service
70 - LG Bridge Service
71 - LGPartnerBookmarksProvider
72 - LG RCS Services
73 - RcsCall
74 - SharedSketch
75 - SnapPage
76 - Tasks storage
77 - Update Center
78 - Voice Recorder
79 - LG WFDS Services
80 - LIA Informant
81 - LIA S4URecommender
82 - LG Connectivity Service
83 - My Places Engine
84 - My Place
85 - RCSProvider
86 - SmartSetting
87 - Tags
88 - qcrilmsgtunnel
Click to expand...
Click to collapse
Now you are rooted, have adaway, pass safetynet & debloated all the LG s*** out of this rom.
Go to the magisk manager download section and find other great systemless mods
THX goes to:
@twrp team and @steadfasterX for TWRWP
@kessaras for v29a flashable zip
@Deic for universal safetynet fix beta 5
All the others I forgot.
pOpY
What does the author of this thread mean by "systemless debloat"?
Isn't just disabling/freezing apps enough?
Also, how can you pass safetyNet? I cannot pass it even with safetyNet Universal fix...
Reserved
So, there is no way to pass Safety net with roms like H-rom g4 or even worse, Los, right?
polfrank said:
So, there is no way to pass Safety net with roms like H-rom g4 or even worse, Los, right?
Click to expand...
Click to collapse
Sorry, i havent installed the roms and just done this on v29a stock.
Have updated the Op with better instructions on how i have done it.
Would be nice if you could try it and report back.
pOpY
polfrank said:
So, there is no way to pass Safety net with roms like H-rom g4 or even worse, Los, right?
Click to expand...
Click to collapse
I was passing Safety net back on the last Official LOS 14.1 using at the time 15.0 Magisk, universal safety fix and magisk hide. I don't remember all the settings, Now I am on CypherOS and still passing with 15.3 and universal. I mod and change my /system all the time and pass.
What is your setup? Maybe with more information I can help.
Edit: also nice post OP. I'll probably be installing Adaway soon, just never bothered. Also for the terminal debloater, what exactly does that do? Just hide the apps? I mainly just use the TWRP terminal and remove apps from /system that way, but I leave some that I am unsure if they are needed or not. Do you know which ones are always required?
Thx, for your kind words.
Adaway is a must have [emoji3]
No ads, yeah.
Regarding the terminal debloater module, it removes the apk and write a placeholder file. The result is the same like you do (remove the apk), BUT you can disable the whole module or enable single apps and system partition isn't touched!
The list above I have written down from several threads and by trial and error.
Until now, no issues...
Wait... One.. Better battery life [emoji56]
pOpY
Gesendet von meinem LG-H815 mit Tapatalk
popy2006 said:
Thx, for your kind words.
Adaway is a must have [emoji3]
No ads, yeah.
Regarding the terminal debloater module, it removes the apk and write a placeholder file. The result is the same like you do (remove the apk), BUT you can disable the whole module or enable single apps and system partition isn't touched!
The list above I have written down from several threads and by trial and error.
Until now, no issues...
Wait... One.. Better battery life [emoji56]
pOpY
Gesendet von meinem LG-H815 mit Tapatalk
Click to expand...
Click to collapse
Thats pretty cool. I may check it out soon. I'm trying to not to use a lot of Magisk modules on such a new rom (CypherOS 5.1) to be sure everything works. But better battery life is my aim right now. Thanks for the explanation.
tambukey said:
Thats pretty cool. I may check it out soon. I'm trying to not to use a lot of Magisk modules on such a new rom (CypherOS 5.1) to be sure everything works. But better battery life is my aim right now. Thanks for the explanation.
Click to expand...
Click to collapse
You are welcome
Final step, OPEN Terminal Emulator and type:
su
debloat
^^the app list to debloat (in OP) are found in both options #1 and #2
One note: Print Spooler is necessary if you plan to print any documents/pictures onto paper from a printer.
Thanks for the guide!!
Guys I can't run Magisk on my LG G4 H815 with Nougat v29a. After removing Supersu and flashing magisk 17.1 with twrp, the phone doesn't boot normally. It reboots recovery when I click reboot system. It always reboot recovery. I don't know why.
Do you have any Idea?
Use magisk 16.0, that's the version I am using. With 17 and 17.1 I also had those issues.
Good luck
pOpY
Gesendet von meinem LG-H815 mit Tapatalk