I have problem in my HP 6815rw, during update software my handset turned off because of my computer reboot and now it’s like a dead and not able to turn on and only red light appear when charging or usb cable switched is there possible that its loader reload again?? pls help me accordingly
Regards
Mani
Hi.
My phone stuck on boot. But when I plug with an usb cable to my pc it detects for 17 secs and in this short time the kdz tool cant detect my phone
BATTERY OUT.
VOLUME DOWN + PLUG USB CABLE phone will start in emergency mode now flash KDZ.
You also can try by following the instructions cited above but pressing volume down and up at the same time.
I was playing Clash of Clans and charging my phone. It turn off and I couldn't do anything with it.
I saw this video www youtube com watch?v=EL12Cq9X3oo and I tried but I have some problems.
At first, phone was detected by Qcom Phone Download Tools v2:1.0.1 , and I could start download. It stopped at 3% and since this moment the phone is not detected like COM PORT. It is detected like Human Interface USB.
I don't know what I have to do. I have waited 2 days, to drain the batery and computer is recognized as the same, Human Interface USB
I am using a virtual machine with XP 32bits.
Please help.
Dawhol said:
I was playing Clash of Clans and charging my phone. It turn off and I couldn't do anything with it.
I saw this video www youtube com watch?v=EL12Cq9X3oo and I tried but I have some problems.
At first, phone was detected by Qcom Phone Download Tools v2:1.0.1 , and I could start download. It stopped at 3% and since this moment the phone is not detected like COM PORT. It is detected like Human Interface USB.
I don't know what I have to do. I have waited 2 days, to drain the batery and computer is recognized as the same, Human Interface USB
I am using a virtual machine with XP 32bits.
Please help.
Click to expand...
Click to collapse
simply don't use a VM but do it on natively OS
nziria said:
simply don't use a VM but do it on natively OS
Click to expand...
Click to collapse
yes, now i am travelling, so I have my laptop with VM. Tomorrow I will stay at home and I will try with XP computer, but I think it wont work.
The video I've linked is in a VM too.
nziria said:
simply don't use a VM but do it on natively OS
Click to expand...
Click to collapse
Hello!!
I have tried in XP 32bit PC and it didn't work. Computer detects the phone as HID :S
Before connect the phone, I installed the QCom drivers but nothings special happends when I plug the phone. No recognized as COM Port.
I don't know what I need to do, I think it should exist a solution
Please help!!!
Dawhol said:
Hello!!
I have tried in XP 32bit PC and it didn't work. Computer detects the phone as HID :S
Before connect the phone, I installed the QCom drivers but nothings special happends when I plug the phone. No recognized as COM Port.
I don't know what I need to do, I think it should exist a solution
Please help!!!
Click to expand...
Click to collapse
Windows 7 32bit should be okay. Try my guide in the gionee elife e7 general thread. If it doesnt work, keep uninstalling the usb input device and try different combos with the volume and power buttons before plugging USB to computer. If your LED light blinks red while you are connected as USB input device that increases your probability of succeeding.
Sent from unbricked Elife e7.
StarLord21 said:
Windows 7 32bit should be okay. Try my guide in the gionee elife e7 general thread. If it doesnt work, keep uninstalling the usb input device and try different combos with the volume and power buttons before plugging USB to computer. If your LED light blinks red while you are connected as USB input device that increases your probability of succeeding.
Sent from unbricked Elife e7.
Click to expand...
Click to collapse
I did. I have unbricked the phone. I made a factory cable and the PC recognized the phone.
I have one problem. Battery is always 1%.... and if i disconnect the charger mobile turn off in less than minute.
I am updating to KitKat with the phone update. I hope update fix the error.
EDIT: I used Win7 64bits.
Dawhol said:
I did. I have unbricked the phone. I made a factory cable and the PC recognized the phone.
I have one problem. Battery is always 1%.... and if i disconnect the charger mobile turn off in less than minute.
I am updating to KitKat with the phone update. I hope update fix the error.
EDIT: I used Win7 64bits.
Click to expand...
Click to collapse
Phone after disconnect charger went off. When I connected the phone to the pc the problem returns... It recognized as HID. I tried some restarts, push PW button 12 second and after disconnect the cable, etc...
When I was triying to detect the phone as port com, light red was freeze and turned on without the usb cable.
I press power, vol+ and vol- for few seconds and red light stopped. After that the phone was charging normally.
When I woke up it was 100% .
Have u tried Qualcomm fastboot
Three days ago, my phone went off by itself and I had a hard time starting again, it was just loading the bootanimation, I tried to reinstall the ROM, but it did not go into TWRP, although the message Recovery appears on the screen, I insisted and after several attempts, I got into the recovery, formatted everything and I installed the AICP ROM again, and I had to restart,my phone freezes in the LeEco bootloader, then again I insisted until the ROM finally started, but soon realized that it was taking too long to start (30 minutes waiting and nothing).
So I rebooted again, and from then on, I can not go into any mode anymore, trying to access the TWRP, the phone only stays on the Recovery screen until reboot after 2 minutes, when letting the phone try to start the ROM, it only stays on the LeEco screen and restart after 2 minutes, when entering Fastboot, it enters the screen in Fastboot mode, but is not recognized by the computer, not even as unknown device, the same for Download mode.
Is there anything I can try?
Doesn't seem like a a fried motherboard. In my experience, If you fried the CPU, you would still be able to access Fastboot, if you fried the GPU part of the chip, or if the LCD has failed you would feel vibrations..
Do you thin it is possible that you accidentally put the phone into EDL mode? It can sometimes be hard to get out of, and it will give you similar issues.
To leave EDL press and hold volume down and power for 1 minute or longer.
Try this
Install the All in One tool and use it to update your android and fastboot drivers. Afterwards see if the computer recognises the phone port connection by going to Control Panel>System> Device Manager* ( Even though, you may not see the drive, you will maybe still see unknown device or te port)
Maybe a Brick?
If it does not see the phone or show a unknown USB device with port 9008
Try placing the phone into EDL mode by pressing and holding the Vol Up (+) and Vol Down (-) together while simultaneously connecting the phone by USB cable to the computer. Do you see the port or phone now? If you see port 9008 you possibly are bricked, follow the steps on my unbricking thread., if you can not get back to TWRP, or fastboot,and the phone keeps a charge. Then I would think that you are definitely bricked.
Other possible issues
The issue could be the battery. Have you tried using other USB C Cables? If you can use a different usb cable let it charge for a couple of hours then see if you can get into TWRP again . If you can enter fastboot mode try reflashing TWRP, you can use the All in One tool for this.
tsongming said:
Doesn't seem like a a fried motherboard. In my experience, If you fried the CPU, you would still be able to access Fastboot, if you fried the GPU part of the chip, or if the LCD has failed you would feel vibrations..
Do you thin it is possible that you accidentally put the phone into EDL mode? It can sometimes be hard to get out of, and it will give you similar issues.
To leave EDL press and hold volume down and power for 1 minute or longer.
Try this
Install the All in One tool and use it to update your android and fastboot drivers. Afterwards see if the computer recognises the phone port connection by going to Control Panel>System> Device Manager* ( Even though, you may not see the drive, you will maybe still see unknown device or te port)
Maybe a Brick?
If it does not see the phone or show a unknown USB device with port 9008
Try placing the phone into EDL mode by pressing and holding the Vol Up (+) and Vol Down (-) together while simultaneously connecting the phone by USB cable to the computer. Do you see the port or phone now? If you see port 9008 you possibly are bricked, follow the steps on my unbricking thread., if you can not get back to TWRP, or fastboot,and the phone keeps a charge. Then I would think that you are definitely bricked.
Other possible issues
The issue could be the battery. Have you tried using other USB C Cables? If you can use a different usb cable let it charge for a couple of hours then see if you can get into TWRP again . If you can enter fastboot mode try reflashing TWRP, you can use the All in One tool for this.
Click to expand...
Click to collapse
Thanks for answering. I've tried everything.
But I can not see the smartphone when connected. USB drivers are properly installed (I used to recover other LeEco x651, x526 and x520 devices)
I left it restarting for more than hours holding the power button and volume down, no results.
The device does not appear in the Windows device manager in any way, not even as Unknown or 9008 port.
I tried several usb cables.
There is no communication with TWRP or ROM installed and neither with the computer, even though I enter into fastboot / 9008 mode. Only LeEco / recovery logo and Fastboot screen.
I think my main memory is damaged or something.
kakobr said:
Thanks for answering. I've tried everything.
But I can not see the smartphone when connected. USB drivers are properly installed (I used to recover other LeEco x651, x526 and x520 devices)
I left it restarting for more than hours holding the power button and volume down, no results.
The device does not appear in the Windows device manager in any way, not even as Unknown or 9008 port.
I tried several usb cables.
There is no communication with TWRP or ROM installed and neither with the computer, even though I enter into fastboot / 9008 mode.sl Only LeEco / recovery logo and Fastboot screen.
I think my main memory is damaged or something.
Click to expand...
Click to collapse
Well that sucks, if you feel like sending to the phone to China for repair, you can find several shops that are offering to repair any damaged Leeco for $10 and an average cost of $30 for resoldering. On the TaoBao website, use Chrome for translation. Some of their ads mention overseas repair
If it's memory it would be an easy fix for them.
If you don't want to fix it, I highly recommend the Mi8 if it's within your budget, its a perfect phone and you can find them for close to $300. My brother has a Redmi note 6 Pro which is also really nice. He paid $190.
Good Luck.
Sent from my Xiaomi MI 8 using XDA Labs
kakobr said:
Thanks for answering. I've tried everything.
But I can not see the smartphone when connected. USB drivers are properly installed (I used to recover other LeEco x651, x526 and x520 devices)
I left it restarting for more than hours holding the power button and volume down, no results.
The device does not appear in the Windows device manager in any way, not even as Unknown or 9008 port.
I tried several usb cables.
There is no communication with TWRP or ROM installed and neither with the computer, even though I enter into fastboot / 9008 mode. Only LeEco / recovery logo and Fastboot screen.
I think my main memory is damaged or something.
Click to expand...
Click to collapse
Check out this possible do it yourself fix : https://forum.xda-developers.com/showpost.php?p=79302729&postcount=71
so been trying to update my axon 7 and ended up with no fastboot but unlocked, with stock oreo
played about abit further and phone would show as zte diagnostics dfu when plugged in (using stock cable)
i might of been in edl? mode (not flashing anything or doing anything as no tools would detect phone but was in device manager as zte diagnostics. i think i unplugged it to reboot but now it does nothing at all
no led, no haptic buzz no screen
tried removing sim and microsd, tried long presses and short presses. nothing
pc doesnt detect it when plugging in
any ideas? :'(