Hello,
I found out that i need two update.app since EMUI 5. How do i use the dload method to return to stock EMUI when i'm on a custom ROM?
I have an update.zip with an update.app inside and an WAS-L21_hw_eu/update_WAS-L21_hw_eu.zip and there is also an update.app inside.
Could anyone give me a step by step instruction how to do this?
Thanks in advance
Related
Hello, today i have decided to update to nougat so i have downloaded and installed CAN-L01C150B330 from firmware search, when i go to settings the updater tab is missing, if i search updater on setting, updater is show but i can`t open it....so i have tried to do a factory reset, phone boot into recovery stared factory reset but stopped at 5%.
I am the only one with the missing updater and the factory reset error?
What i`m doing wrong?
Here are the steps fallowed to install nougat:
- unlock bootloader
- download the firmware
- extract update.app and copy to dload folder in the root of sd card
- extract recovery.img from update.app with huawei extract tool
- flash extracted recovery.img with fastboot
- boot into recovery and update to nougat.
I had the same issue. After i installed the eu update package, i got the updater in settings back.
BaLLi89 said:
I had the same issue. After i installed the eu update package, i got the updater in settings back.
Click to expand...
Click to collapse
how did you install?? i have tried to install as instructed but update failed
make it like Jozinek has written in this thread (https://forum.xda-developers.com/nova-plus/how-to/c432b320-android-7-0-available-try-t3527084)
only i have the eu update package just as extracted and installed as the full package.
1. download both zip files
2. extract the full update zip and put the UPDATE.APP file in the dload directory on the root of your sd card
3. force updating by (poweroff your phone and) holding all three buttons on right side together
4. wait until the update is complete
5. extract the eu update zip and put the UPDATE.APP file in the dload directory on the root of your sd card
6. force updating by (poweroff your phone and) holding all three buttons on right side together
7. you have it (i hope so )
Forgive me if my English is not the best
BaLLi89 said:
make it like Jozinek has written in this thread (https://forum.xda-developers.com/nova-plus/how-to/c432b320-android-7-0-available-try-t3527084)
only i have the eu update package just as extracted and installed as the full package.
1. download both zip files
2. extract the full update zip and put the UPDATE.APP file in the dload directory on the root of your sd card
3. force updating by (poweroff your phone and) holding all three buttons on right side together
4. wait until the update is complete
5. extract the eu update zip and put the UPDATE.APP file in the dload directory on the root of your sd card
6. force updating by (poweroff your phone and) holding all three buttons on right side together
7. you have it (i hope so )
Forgive me if my English is not the best
Click to expand...
Click to collapse
solved. :good:
BaLLi89 said:
make it like Jozinek has written in this thread (https://forum.xda-developers.com/nova-plus/how-to/c432b320-android-7-0-available-try-t3527084)
only i have the eu update package just as extracted and installed as the full package.
1. download both zip files
2. extract the full update zip and put the UPDATE.APP file in the dload directory on the root of your sd card
3. force updating by (poweroff your phone and) holding all three buttons on right side together
4. wait until the update is complete
5. extract the eu update zip and put the UPDATE.APP file in the dload directory on the root of your sd card
6. force updating by (poweroff your phone and) holding all three buttons on right side together
7. you have it (i hope so )
Forgive me if my English is not the best
Click to expand...
Click to collapse
Still i am not able to install the eu pack, uptade stops at 52%.
i dont know, if anything is wrong with your unlocked bootloader combined with the update package. that is the only idea i have.
BaLLi89 said:
i dont know, if anything is wrong with your unlocked bootloader combined with the update package. that is the only idea i have.
Click to expand...
Click to collapse
Bootloader was locked....i just don't know why update stops at 52%. Now i'm back on android 6, i'll wait for the oficial update.
Hu guys.. i have p9 plus and after i updte to nougat, my updater goes missing. Can sombody pls help me.. my build number changed into NDR90M test keys.. wht to do?
Iamdesireeabalos said:
Hu guys.. i have p9 plus and after i updte to nougat, my updater goes missing. Can sombody pls help me.. my build number changed into NDR90M test keys.. wht to do?
Click to expand...
Click to collapse
In got the same problem. Don't you have a small update package for eu verion? I didn't manage to install update for eu version so i'm stuck at beta version, i have to wait the official stable release.
Look here https://www.google.ro/amp/www.theandroidsoul.com
Hello,
Got a WAS-LX1A SINGLE SIM 4GB UK (with an updated WAS-LX1AC432B185 firmware).
Trying to go back to stock but all firmware (WAS-LX1AC432B179, WAS-LX1AC432B186, WAS-LX1AC432B187) which has been downloaded using Firmware Finder is failing via dload method: "Software Install Failed"
Any ideas or a link would to a firmware where I can start would be good,
Thanks
buddimanv said:
Hello,
Got a WAS-LX1A SINGLE SIM 4GB UK (with an updated WAS-LX1AC432B185 firmware).
Trying to go back to stock but all firmware (WAS-LX1AC432B179, WAS-LX1AC432B186, WAS-LX1AC432B187) which has been downloaded using Firmware Finder is failing via dload method: "Software Install Failed"
Any ideas or a link would to a firmware where I can start would be good,
Thanks
Click to expand...
Click to collapse
hi:
check this:
b182 =ds: 182, 184, 186 and so on....
b183= ss: 179, 183, 185, 187 so on...
-------------------------------------===== follow instructions of below if is bricked
now:
you need unlock bootloader
oeminfo ss
srom b183
twrp
sdcard
1- with a sdcard, create dload folder, then extract b183 and copy update.app + all was folders.
2- enable developer settings and enable oem unlock, poweroff and press vol-+power, then fastboot oem unlock code, then follow the screen(configs)
3- move twrp to c:/adb, with a cmd opened type cd c:/adb press enter, and type fatboot flash recovery recovery.img, finished type fastboot reboot plus pressing vol + till erecovery screen, shutdown and unplug, press vol+ power.
4- insert sdcard and make only a backup of your oeminfo, extract downloaded oem and copy/replace in twrp back folder, then restore in twrp. power off now only do 3buttons method
Thanks foliaje, I have tried WAS-LX1AC432B179 and its not working. The phone boots fine. Basically, I rooted and it tried to update via TWRP and failed. Now trying to restore to stock and getting this error. DO you have a link to the exact firmware that I can try - tried several of them now and its failing.
Ok, I managed to go back to stock by downloading via Firmware Finder. So, dload method via SD Card don't work with this phone or what? Would appreciate if someone can confirm?
buddimanv said:
Thanks foliaje, I have tried WAS-LX1AC432B179 and its not working. The phone boots fine. Basically, I rooted and it tried to update via TWRP and failed. Now trying to restore to stock and getting this error. DO you have a link to the exact firmware that I can try - tried several of them now and its failing.
Click to expand...
Click to collapse
links below and follow the guide of above, by the way otas doesnt work with twrp or/and root.
if your p10lite came with b183(confirm please) now you must have installed b185 or b187
https://drive.google.com/open?id=0B-k_1rnfFeEvTjkyLXNSVjVTSm8 oeminfo
https://forum.xda-developers.com/p10-lite/help/original-service-rom-huawei-p10-lite-t3688097 download servicerom b183
foliaje said:
links below and follow the guide of above, by the way otas doesnt work with twrp or/and root.
if your p10lite came with b183(confirm please) now you must have installed b185 or b187
https://drive.google.com/open?id=0B-k_1rnfFeEvTjkyLXNSVjVTSm8 oeminfo
https://forum.xda-developers.com/p10-lite/help/original-service-rom-huawei-p10-lite-t3688097 download servicerom b183
Click to expand...
Click to collapse
Hey foliaje, Thanks for your help, appreciate it.
Let me explain my issue: I have purchased my phone yesterday, it upgraded to 185 (I am assuming it was B183, didn't check) via OTA. Then I almost finished setting up the phone including ROOT but a b187 OTA appeared little bit later but failed because I had TWRP already installed. That's fine, no problem. So wanted to start again like I usually do - download the firmware, put on sd card and off you go......
But the problem with this phone is (and I had quite few Huawei one's including tablets) when I downloaded the full firmware, using the SD card dload method I get "Software Install Failed" but it seemed to have worked when I did it via Firmware Finder (I am on B187 now). So something not right - either something has changed or I need to do something else.
So what's the issue? The only think I can think of here is that you are saying that this phone require a 'service' firmware that does not do authentication or something? Right? I am downloading C432B183 from your link and will see what happens (bit slow).
I really would like to know now so I can get back to stock when I mess things up
OK...I followed as below:
Downloaded http://androidhost.ru/JS
(1) Copied main UPDATE.APP to dload folder
(2) Then renamed WAS-L01A_hw_eu\update_WAS-L01A_hw_eu.app to UPDATE.APP and copied to dload folder
Is above method correct, can we do it in one go?
Anyway, I think it has worked (had to do few reset) but the firmware version was showing WAS-LX1AC432B179 - is that correct? OTA upgraded to WAS-LX1AC432B185
buddimanv said:
WAS-LX1AC432B179 - is that correct
Click to expand...
Click to collapse
yeah it is correct, by the way in 2) is not necesary rename the update.app only copy all folders to sdcard
foliaje said:
yeah it is correct, by the way in 2) is not necesary rename the update.app only copy all folders to sdcard
Click to expand...
Click to collapse
Thanks dude, appreciate your help.
Now - any ideas why the firmware finder firmware's don't work on this phone via dload method?
buddimanv said:
Thanks dude, appreciate your help.
Now - any ideas why the firmware finder firmware's don't work on this phone via dload method?
Click to expand...
Click to collapse
In the UK and have exact same model. Filmware finder did not work for me also. The one in the link below did though! Its the first download you need. Copy the update.app and the folder 'L01A' to the 'dload' folder on your sd card. Does your phone boot? If so in the dialer type *#*#2846579#*#* and choose software upgrade then sd card update, it will then flash the filmware to pure stock.
https://forum.xda-developers.com/p10-lite/help/original-service-rom-huawei-p10-lite-t3688097
stonedpsycho said:
In the UK and have exact same model. Filmware finder did not work for me also. The one in the link below did though! Its the first download you need. Copy the update.app and the folder 'L01A' to the 'dload' folder on your sd card. Does your phone boot? If so in the dialer type *#*#2846579#*#* and choose software upgrade then sd card update, it will then flash the filmware to pure stock.
https://forum.xda-developers.com/p10-lite/help/original-service-rom-huawei-p10-lite-t3688097
Click to expand...
Click to collapse
Yes, its all good now. Bizarre - Huawei making things difficult now. Which TWRP are you using? Can the TWRP backup function works for you i.e. encryption disabled?
My device is p9 lite vns l31( c636) before i used elite roam v7.6. but now i want to go back stock roam. To go back i used roall back mm and c636b170 full ota. But now my devise build number is c900b170. I want to upgrade nauget c636. Please help me.
rathnayakepr3 said:
My device is p9 lite vns l31( c636) before i used elite roam v7.6. but now i want to go back stock roam. To go back i used roall back mm and c636b170 full ota. But now my devise build number is c900b170. I want to upgrade nauget c636. Please help me.
Click to expand...
Click to collapse
Hello man,
did you removed prevoius update.app from SD card, the one from rollback??
Maybe you forgot to do this...
If you sure you done all things right then take a look at the UNIFIED HELP THREAD...
At 6th post you'll find a L31 rollback package that will give you C900B300 global firmware.
From this flash C636B170 full ota and see if worked this time....
https://forum.xda-developers.com/huawei-p9lite/how-to/unified-help-thread-huawei-p9-lite-t3649152
Dadditz said:
Hello man,
did you removed prevoius update.app from SD card, the one from rollback??
Maybe you forgot to do this...
If you sure you done all things right then take a look at the UNIFIED HELP THREAD...
At 6th post you'll find a L31 rollback package that will give you C900B300 global firmware.
From this flash C636B170 full ota and see if worked this time....
https://forum.xda-developers.com/huawei-p9lite/how-to/unified-help-thread-huawei-p9-lite-t3649152
Click to expand...
Click to collapse
.
But i donnt know how to flash oem info and custom bin through the toolkit. Please help me.
rathnayakepr3 said:
.
But i donnt know how to flash oem info and custom bin through the toolkit. Please help me.
Click to expand...
Click to collapse
Hello dude,
in the guide i never readed to use the toolkit, that's another way i think...
Flashing the rollback package will bring you c900b300 firmware wich means global intermediate transitive firmware...
Create a dload folder in SD card, extract update.app from rollback package and put in it.
Turn off you phone. Now disconnect from PC, and let it start keeping vol+ vol- and power buttons.
When it ends turn it off and remove the SD card and the update.app from dload folder.
Download and extract update.app from L31C636B170 full update.
If you missed it...
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1164/g104/v66846/f1/full/update.zip
Put this in dload folder in SD card again and put in your phone...
Repeat vol+ vol- power buttons and it will flash...
Recommended: when finished reboot to e_recovery (vol+ power buttons) and factory reset.
If all gone well you will stay now on marshmallow firmware..
Wish you the best my friend...:fingers-crossed:
Edit: flash the rollpack package suggested in prevoius post.
All credits goes to @dariomrk and other contributors that create the thread.
Thank you guys.
Hi could someone help me with detailed instructions on how to go back to stock rom for Huawei P Smart FIG-LX1
coming from PHH AOSP project treble rom
I used firmware finder on pc
downloaded an update.zip file
Created a folder called DLOAD on my sd card ( external )PP file
copied the Update.APP file into there
I had a screen that said Installing update... 5%
The phone turned off then turned back on
I tried again and I got software installation failed
Edit: unpacking the system.img and kernel.img from the update.APP file through a tool called Huawei Update extractor and flashing through fastboot worked
OK Download the stock rom via firmwarefinder and copy it to SD Card ....Download huru updater and copy them to the update.zip. .......Boot into Twrp install ....huru updater and press Down or up the flash beginns after few minutes you can reboot .....enjoy New stock Rom ?
It'd be great if someone could help me with the following issue: my P8 lite is on firmware B896 and if I force-install the transition package, I put into the dload folder and named UPDATE.APP, I get an error during the installation. Please tell me how to do the rollback and install the stock firmware, I don't know how to do it in ADB.
Thanks
niceguy234 said:
It'd be great if someone could help me with the following issue: my P8 lite is on firmware B896 and if I force-install the transition package, I put into the dload folder and named UPDATE.APP, I get an error during the installation. Please tell me how to do the rollback and install the stock firmware, I don't know how to do it in ADB.
Thanks
Click to expand...
Click to collapse
You must EXTRACT from update.zip the UPDATE.APP, not rename it!
.
can you give me the link for the proper update.zip pls?