Database Users

Note killed? (After Rocket-ROM) please help me!

Sorry of my poor English but because, which is only a translation of google. But i can read and understand english.
Unfortunately I am in despair, because apparently I shot my note. So you are my last hope.
Do not worry, I do not expect that Rocket-ROM was the cause, but still my note do not want.
I had recently been used the very cool Rocket V8, and then install the game from Gameloft M99. At the first call about the game loads down 1100MB, or rather it wants. So did release my misery, because every time at 70 MB to 100 MB, the note went into the SoD, and could only be by a long press the power button to move to restart. After several attempts to download via Wi-Fi yet to get out, then the my note shows only in the boot animation and stayed there seemingly stuck in a loop (until min to 30. Wait). Several attempts later, I tried in recovery-mode to delet cache and Davlik, but also did not lead to success. I then tried a in the recovery a full wipe-making, where the note was then stuck too (also up to 30 min. Wait).
Since this has not brought anything, I wanted to flash with Odin 3 (1.85) a stock-ROM (N7000XXKKA_N7000XEUKK3_N7000XXKK5_HOME.tar.md5), but in Odin "<ID:0/003> NAND Write Start!" remains standing.
I have at thecond trie to flash a three part ROM, but the log-screen from odin shows following:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_N7000XXKJ1_CL627135_REV02_user_low_ship.tar.m d5 is valid.
<OSM> MODEM_N7000XXKJ1_REV_05_CL1067428.tar.md5 is valid.
<OSM> GT-N7000-MULTI-CSC-OXAKJ1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Sbl.bin
...... and ........ stands and stands and stands .......... ...........
I have also tried to flash just a kernel, with the same result. Even my attempt to redefine the partitions (with suitable PIT) and then flash the firmware ends similarly, that confirms (again for 30 minutes waiting and nothing is happening.)
<OSM> Check MD5 .. Thurs unplug not the cable ..
<OSM> Please wait ..
<OSM> N7000XXKKA_N7000XEUKK3_N7000XXKK5_HOME.tar.md5 is valid.
Checking MD5 <OSM> Successfully finished ..
Leave <OSM> CS ..
<ID:0/003> Odin v.3 engine (ID: 3) ..
File <ID:0/003> analysis ..
<ID:0/003> Setup connection ..
<ID:0/003> Initialzation ..
Set PIT <ID:0/003> file ..
DO NOT TURN OFF TARGET <ID:0/003>!
I hope someone of you has an idea, because I really could cry!
P.S. CWM now I'm no longer pure, normal boot will stand with the Samsung logo. Download mode goes. The DL-counter shows number 1.

if you can go to download mode again your note is not killed
try to do same ones more time
it has to go right
did you do like this ?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Note sure if I got it right but it sounds liek you can still boot into recovery. Have you made Backup which you can restore?

I've already tried countless times today over again, even with PIT for the repartitioning.
If I use a PIT in the Flash plug operation stucks after the PIT.

In the recovery-mode can't I'm no longer, and my backups I have on the external SD moved.

I guess you put the phone into ODIN-mode by holding Vol- + midle key + On/Off right?
I have not had this before.. so you could try to flash again via ODIN that way.. in case you have not tried already. Not sure if KIES will communicate with the Note in ODIN mode. But also this would be worth a try.

thommic said:
I guess you put the phone into ODIN-mode by holding Vol- + midle key + On/Off right?
I have not had this before.. so you could try to flash again via ODIN that way.. in case you have not tried already. Not sure if KIES will communicate with the Note in ODIN mode. But also this would be worth a try.
Click to expand...
Click to collapse
1. So i have it do anytime.
2. Kies will not communicate with my Note in Odin-Mode.
A normal boot without push of the key-comnbination, let the note show the screen with smartphone ... "exclamation mark" ... PC.

try to download this rom
http://hotfile.com/dl/135702954/9c9d385/N7000XXKKA_N7000OXXKK6_XEO.zip.html
then thick PDA in odin
then put your note in download mode(odin mode) vol down+home+off button
then push start in odin

I have try it, but the result is:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXKKA_N7000OXXKK6_N7000XXKK5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img
and here stop the flash.
I give the Note back to Amazon.

pctelco said:
I have try it, but the result is:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXKKA_N7000OXXKK6_N7000XXKK5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img
and here stop the flash.
I give the Note back to Amazon.
Click to expand...
Click to collapse
just do a factory reset/clean install:reinstall all the sofware maybe its damaged..format your sd...and install a stock rom

Nicht zurück geben !!!
Follow this instruction
http://jjpda.blogspot.com/2011/11/n7000-how-to-flash-n7000zskk1-236.html

nowy57 said:
try to download this rom
http://hotfile.com/dl/135702954/9c9d385/N7000XXKKA_N7000OXXKK6_XEO.zip.html
then thick PDA in odin
then put your note in download mode(odin mode) vol down+home+off button
then push start in odin
Click to expand...
Click to collapse
First of all make sure the Kies is installed on your computer correctly. If the USB Samsung Drivers are corrupted ODIN will not be able to access Note properly! I would try to uninstall and install Kies again. Good luck!!!!

Haddar said:
First of all make sure the Kies is installed on your computer correctly. If the USB Samsung Drivers are corrupted ODIN will not be able to access Note properly! I would try to uninstall and install Kies again. Good luck!!!!
Click to expand...
Click to collapse
exactly !!
if you are not shure reinstal kies once more time by the newest version of kies

gerardroid said:
just do a factory reset/clean install:reinstall all the sofware maybe its damaged..format your sd...and install a stock rom
Click to expand...
Click to collapse
I can't do that. I came only in the DL-Mode, but not in CWM!
I would like to do so, but i can't.

Maybe this can help:
http://www.ebay.com/itm/UnBrick-USB...937128?pt=PDA_Accessories&hash=item3a6dc827e8

gerardroid said:
just do a factory reset/clean install:reinstall all the sofware maybe its damaged..format your sd...and install a stock rom
Click to expand...
Click to collapse
budalica said:
Nicht zurück geben !!!
Follow this instruction
http://jjpda.blogspot.com/2011/11/n7000-how-to-flash-n7000zskk1-236.html
Click to expand...
Click to collapse
Sorry, but this ended by the same results, then all my other tries to rescue my note.
I have no other option than to send the note back to Amazon.

pctelco said:
Sorry, but this ended by the same results, then all my other tries to rescue my note.
I have no other option than to send the note back to Amazon.
Click to expand...
Click to collapse
The ebay dongle supposedly works...

I have no problem in the DL mode to come, which should help me the USB JIG then?
Unfortunately I can not flash ROM with Odin, because it is always aborted.

@ hotweiss
You're right, supposedly!!?
Would have been interesting but the use of USB-JIG @ SGN is still ****ty.
edit:
@ pctelco
I wrote it already in another forum.
An USB-JIG can unbrick you phone. Can!
The procedure might go like this:
http://www.pocketpc.ch/galaxy-note-...tfernen-flashcounter-reseten.html#post1250472

I know this might seem pointless but it helped me before. Very simple step is unplug phone and do a complete shutdown(not restart) of your computer.

[GUIDE] How To Restore A Stuck Samsung Galaxy SI, SII and SIII

Restoring A Stuck Samsung Galaxy SI, SII and SIII​
Is your phone stuck like this?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Then read on! If not, this may only be useful for those who want to go back to the original Samsung Firmware.
Introduction
Too many people are getting stuck on the Samsung logo so I decided to make a tutorial on how to
get yourself off it. It is a simple tutoiral and noob friendly, but it will take time and patience because
the stock firmware is not just 300mb but can go into 1GB and more. This should on Samsung
Galaxy SI, SII, SIII. They are all tested and working, you may experiment on other phones if you
wish and you have no other choice. Read on for the downloads and instructions.
Downloads
Odin v3.07 - Click Here
Your Firmware - Find Here
Instructions
1. Go here and select your phone and its correct version's official firmware here: http://samsung-updates.com/latest-firmware/
2. Download Odin v3.07
3. Turn phone off completely and put it into download mode (Down Volume, Home Button and Power Button together).
4. After downloading the official firmware extract it and open Odin.
5. Select Auto Boot and F. Reset and put that .md5 file in the PDA section. NOTE: There should be COM: (PORT NUMB) in the first box.
6. Click Start and wait. If it succeeded then it will say PASS in green.
NOTE: This has worked for me and other people have confirmed it working for them after testing.
But if something more happens to your phone, I am not responsible.
Good luck.

Will be attaching more tutorials soon.
Sent from my GT-I9300 using xda premium

This is just a stock firmware flash via Odin as per multiple guides on the forum .
Its not getting off a stuck logo its re flashing full firmware in many cases a factory reset should be the first step or a reflash through recovery of the custom rom .
Multiple exact same guides in my view only confuse noobs .
jje

JJEgan said:
This is just a stock firmware flash via Odin as per multiple guides on the forum .
Its not getting off a stuck logo its re flashing full firmware in many cases a factory reset should be the first step or a reflash through recovery of the custom rom .
Multiple exact same guides in my view only confuse noobs .
jje
Click to expand...
Click to collapse
Got me off stuck on a logo.
Sent from my GT-I9300 using xda premium

AndroidPlant said:
Got me off stuck on a logo.
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
A wipe data often fixes that too, if you have custom recovery,a dalvik/cache wipe could potentially fix it.
A re-flash of the Rom could fix it
.....indeed many things "could" fix it........I know your intentions are good, but could you refrain from posting links to this thread every time a problem comes up, because often the solution is much easier

There doesn't seem to be any i9300 firmwares on that site.

Hi, im doing everything as it says but gives me this
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-m0-m0xx-gti9300.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Added!!
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> recovery.img
<ID:0/007> NAND Write Start!!
<ID:0/007> cache.img
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
please help me

Try different USB cables and USB ports. Try flashing the latest stock ROM from sammobile.com.

help plz
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGOF1_I9300OXXGOF1_I9300XXUGNB1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> tz.img
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Cant pass this part.

audit13 said:
Try different USB cables and USB ports. Try flashing the latest stock ROM from sammobile.com.
Click to expand...
Click to collapse
Yes, i've already done that still nothing.
Could it be hardware related issue?

You confirmed the model # in download mode? It fails with the original Samsung usb cables too?

[Q] Bricked Galaxy Tab 4 7.0 Stuck in Odin

Hello everyone! Its been a while since my rooting days(HTC ONE) and I'm a bit if not very rusty . I recently bought a Galaxy Tab 4 7.0. I attempted a root process through Odin and of course...it failed. Now I am stuck in the download mode and no matter what combination of buttons I use it returns there. I tried to see if I can get the original firmware through samfirmware.com for t230NU but to no avail. Any suggestions? I'd really appreciate it as I need the tablet. :fingers-crossed:

[email protected] said:
Hello everyone! Its been a while since my rooting days(HTC ONE) and I'm a bit if not very rusty . I recently bought a Galaxy Tab 4 7.0. I attempted a root process through Odin and of course...it failed. Now I am stuck in the download mode and no matter what combination of buttons I use it returns there. I tried to see if I can get the original firmware through samfirmware.com for t230NU but to no avail. Any suggestions? I'd really appreciate it as I need the tablet. :fingers-crossed:
Click to expand...
Click to collapse
stock firmware
http://forum.xda-developers.com/showthread.php?t=2778374
root
http://forum.xda-developers.com/showpost.php?p=53020637&postcount=87

Android Terminal Emulator cant find mrw
ShinySide said:
stock firmware
http://forum.xda-developers.com/showthread.php?t=2778374
root
http://forum.xda-developers.com/showpost.php?p=53020637&postcount=87
Click to expand...
Click to collapse
Thank you ShinySide for all your help! I was able to root successfully however when I try to replace vroot with Superuser with the terminal its unable to find the mrw file. I did extract and place the folder to the internal storage. I tried putting the file on the sdcard and that did not work either. What i ended up doing was downloading Superuser from the playstore. Will this have the same effect and will it update the binary correctly? My last question is-My Tab4 is says its a model T230NU but when i registered it n Samsung it shows SM-T230NZWAXAR...will the stock firmware conflict since the build is T230NUUEUOANE2?
Sorry for all the newb questions. I'm so glad I was able to unbrick my device and root though...Thank you so much!

[email protected] said:
Thank you ShinySide for all your help! I was able to root successfully however when I try to replace vroot with Superuser with the terminal its unable to find the mrw file. I did extract and place the folder to the internal storage. I tried putting the file on the sdcard and that did not work either. What i ended up doing was downloading Superuser from the playstore. Will this have the same effect and will it update the binary correctly? My last question is-My Tab4 is says its a model T230NU but when i registered it n Samsung it shows SM-T230NZWAXAR...will the stock firmware conflict since the build is T230NUUEUOANE2?
Sorry for all the newb questions. I'm so glad I was able to unbrick my device and root though...Thank you so much!
Click to expand...
Click to collapse
Post the exact terminal output. You shouldnt have any issue
Theres 2 model numbers. One for the white one for the black. Your tab 4 is SM-T230NZWAXAR which is the white one. SM-T230NYKAXAR is the blacks model number. It doesnt matter which you have its the same firmware. Samsung is just reading your full model number,

hi, iam the same problem, just 3 days ago my tab 4 7" (white) was stuck in a blacl screen with a yellow triangle, said: firmware upgrade encountered an issue, please select recovery mode in kies & try again.
The problem here is i cant enter in DOWNLOAD mode, in other tutorials said, for cellphones, that i need to put over the battery, but, in a tablet, how can i do this? i download a firmware from sammobile, my model number said SM-T230NU , i cant find the american version (i purchase this in radioshack USA) but i downlod the mexican version of Telcel, but nothing, OdIn always find an error, watch:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T230NUUEU0ANE2_T230NUXAC0ANE2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> loke_1st.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> loke_2nd.bin
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
THIS IS ANOTHER try:
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T230XXU0ANE6_T230OXX0ANE2_T230XXU0ANE6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> timh.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
please i need help.
and about the post of ShinySide (http://forum.xda-developers.com/showthread.php?t=2778374 ) what is the diference about NE2 firmware and ND9 firm?

nismo87 said:
hi, iam the same problem, just 3 days ago my tab 4 7" (white) was stuck in a blacl screen with a yellow triangle, said: firmware upgrade encountered an issue, please select recovery mode in kies & try again.
The problem here is i cant enter in DOWNLOAD mode, in other tutorials said, for cellphones, that i need to put over the battery, but, in a tablet, how can i do this? i download a firmware from sammobile, my model number said SM-T230NU , i cant find the american version (i purchase this in radioshack USA) but i downlod the mexican version of Telcel, but nothing, OdIn always find an error, watch:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T230NUUEU0ANE2_T230NUXAC0ANE2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> loke_1st.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> loke_2nd.bin
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
THIS IS ANOTHER try:
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T230XXU0ANE6_T230OXX0ANE2_T230XXU0ANE6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> timh.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
please i need help.
and about the post of ShinySide (http://forum.xda-developers.com/showthread.php?t=2778374 ) what is the diference about NE2 firmware and ND9 firm?
Click to expand...
Click to collapse
Your problem is you are trying to flash the wrong firmware. Youre trying to flash a firmware meant for data/service enabled tabs. Check my first post in this thread. Flash one of those.
Just bug/kernel fixes.
btw if youre seeing that message, you are in download mode.

Cant find mrw file
ShinySide said:
Post the exact terminal output. You shouldnt have any issue
Theres 2 model numbers. One for the white one for the black. Your tab 4 is SM-T230NZWAXAR which is the white one. SM-T230NYKAXAR is the blacks model number. It doesnt matter which you have its the same firmware. Samsung is just reading your full model number,
Click to expand...
Click to collapse
i have tried several times and still the same result. I get this message and then the tablet reboots. The Superuser app I downloaded from the Playstore did update the binary and all. However i would like to know what I did wrong for future reference with the mrw file. Thanks!

ShinySide said:
Your problem is you are trying to flash the wrong firmware. Youre trying to flash a firmware meant for data/service enabled tabs. Check my first post in this thread. Flash one of those.
Just bug/kernel fixes.
btw if youre seeing that message, you are in download mode.
Click to expand...
Click to collapse
thanks for the answer, but, excuse about my question, in u`r post about the firmwares, i just download this: Latest Firmware Version Download NE2, (the first link posted) but said me the same message in odin, (FAIL) i dont know if the options in ODIN are bad, i choose auto rebot and F.Reset Time.
or, need i erase the termination md5 with only .tar?

[email protected] said:
i have tried several times and still the same result. I get this message and then the tablet reboots. The Superuser app I downloaded from the Playstore did update the binary and all. However i would like to know what I did wrong for future reference with the mrw file. Thanks!
Click to expand...
Click to collapse
Do a search for each of those file names and give me the exact file names and locations. Someone else mentioned on another thread they had to ediit the script because they were a little different for some reason for them.
nismo87 said:
thanks for the answer, but, excuse about my question, in u`r post about the firmwares, i just download this: Latest Firmware Version Download NE2, (the first link posted) but said me the same message in odin, (FAIL) i dont know if the options in ODIN are bad, i choose auto rebot and F.Reset Time.
or, need i erase the termination md5 with only .tar?
Click to expand...
Click to collapse
Na those options wouldnt matter. That first time you flashed, loke_1st.bin flashed successfully then loke_2nd.bin failed. You might need to find a pit file for the tab 4 7inch and re-partition the device. Only one tho.... to get the pitfile you need hiemdall and hiemdall isnt compatible with the tab 4. least not yet. I saw a post a while ago for creating a pitfile on a device. Let me see if I can find it and see if itll work on my tab and create one and Ill post it if I can find it and create one
Okay this is all i can find. Just one issue...I have straight linux and no windows on my pc so I cant use or try to use it to get the pit, so 2 options if you want to try repartitioning it, try using this tool in download mode or find someone with windows willing to try to get the pitfile from their device
http://forum.xda-developers.com/galaxy-s2/orig-development/tool-updated-09-06-14-efs-professional-t1308546

ShinySide said:
Na those options wouldnt matter. That first time you flashed, loke_1st.bin flashed successfully then loke_2nd.bin failed. You might need to find a pit file for the tab 4 7inch and re-partition the device. Only one tho.... to get the pitfile you need hiemdall and hiemdall isnt compatible with the tab 4. least not yet. I saw a post a while ago for creating a pitfile on a device. Let me see if I can find it and see if itll work on my tab and create one and Ill post it if I can find it and create one
Click to expand...
Click to collapse
OK, thanks for the support, i will considering make a donation for this $$
so, in conclusion, iam really ina hole with this issue, no? i dont know how i can get brick in this form my tablet, only 3 weeks with it and is stuck...
i dont know much about this and samsung devices, but, need i another file apart of the firmware? the Pit file?

nismo87 said:
OK, thanks for the support, i will considering make a donation for this $$
so, in conclusion, iam really ina hole with this issue, no? i dont know how i can get brick in this form my tablet, only 3 weeks with it and is stuck...
i dont know much about this and samsung devices, but, need i another file apart of the firmware? the Pit file?
Click to expand...
Click to collapse
Check my previous post. I had just edited while you were responding Haha I have the donation link up because some people asked if I had one when I was compiling Carbon for s4's. I never accept them tho so its just there for "show" Ahaha
Its just one file. Contains all the partition block sizes, names, etc etc and willl delete everything and repartition the devices partitions, etc etc
Im guessing the loke bins are the bootloader. And since one flashed for you, it might be failing at a check point.

ShinySide said:
Check my previous post. I had just edited while you were responding Haha I have the donation link up because some people asked if I had one when I was compiling Carbon for s4's. I never accept them tho so its just there for "show" Ahaha
Its just one file. Contains all the partition block sizes, names, etc etc and willl delete everything and repartition the devices partitions, etc etc
Im guessing the loke bins are the bootloader. And since one flashed for you, it might be failing at a check point.
Click to expand...
Click to collapse
Hi again Shinyside,
today was a great day for my tablet jeje, its ALIVE again¡¡¡¡¡¡
what i made?
Just desinstall KIES, and reboot the Pc, install again the drivers for samsung, after, download again the Original firmware from your Link ( chrome://mega/content/secure.html#!I49V3YZB!LkqiYAvZF0dyL0YMbVMGlGWIhn7BQbFi84z4CIFQhKw
i downoad again because, sometimes in large files, the download is corrupted for X reason, unzip this in desktop (i dont know if this is good or not).
the next step was plug to charge for 1 hrs the tab 4, with the black screen turn on, Open Odin 3.07 , wait 2 minutes and upload the ND5 file previous downloaded, plug the TAB 4 in the Pc with (this is important) the OEM cable, i was plugin with other micro usb in the past attempted, so, just when Odin finish to charge 100% the firmware, just press START and wait a couple of minutes, the tablet autoreboot and now is alive.
but... i dont know but when my tab turn on again, all apps, pictures,etc was there so, i dont know if my tablet only was bricked temporarily or not completely bricked..... i dont know, only know that i have a tab again and thanks Shinyside for all support.
So, your link about donation is working or not? i want to invite u a beer, minimum :silly:
i want leave the Odin record about this, if anybody have the same problem:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T230NUUEU0ANE2_T230NUXAC0ANE2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> loke_1st.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> loke_2nd.bin
<ID:0/003> param.lfs
<ID:0/003> DTim.Primary
<ID:0/003> DTim.Recovery
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> NVM.img
<ID:0/003> cache.img

nismo87 said:
Hi again Shinyside,
today was a great day for my tablet jeje, its ALIVE again¡¡¡¡¡¡
what i made?
Just desinstall KIES, and reboot the Pc, install again the drivers for samsung, after, download again the Original firmware from your Link ( chrome://mega/content/secure.html#!I49V3YZB!LkqiYAvZF0dyL0YMbVMGlGWIhn7BQbFi84z4CIFQhKw
i downoad again because, sometimes in large files, the download is corrupted for X reason, unzip this in desktop (i dont know if this is good or not).
the next step was plug to charge for 1 hrs the tab 4, with the black screen turn on, Open Odin 3.07 , wait 2 minutes and upload the ND5 file previous downloaded, plug the TAB 4 in the Pc with (this is important) the OEM cable, i was plugin with other micro usb in the past attempted, so, just when Odin finish to charge 100% the firmware, just press START and wait a couple of minutes, the tablet autoreboot and now is alive.
but... i dont know but when my tab turn on again, all apps, pictures,etc was there so, i dont know if my tablet only was bricked temporarily or not completely bricked..... i dont know, only know that i have a tab again and thanks Shinyside for all support.
So, your link about donation is working or not? i want to invite u a beer, minimum :silly:
i want leave the Odin record about this, if anybody have the same problem:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T230NUUEU0ANE2_T230NUXAC0ANE2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> loke_1st.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> loke_2nd.bin
<ID:0/003> param.lfs
<ID:0/003> DTim.Primary
<ID:0/003> DTim.Recovery
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> NVM.img
<ID:0/003> cache.img
Click to expand...
Click to collapse
Sweet good deal man. Glad you got iit back up and running. I didn't even think about the cable. We an issue with using some different usb cables on the s4 too. But glad you got it back up and running. And yeah it works

the next step is, how to root my tab 4......

nismo87 said:
the next step is, how to root my tab 4......
Click to expand...
Click to collapse
Check post 2

ShinySide said:
Check post 2
Click to expand...
Click to collapse
Hope this is ok area to post this in. I am having a problem with Tab 4 T230NU wifi only. I am trying to get to download mode to flash with Odin, but I can not? It flashes on with screen. "Firmware Upgrade encountered an error an issue. Please select recovery mode in Kies & try again. " It just flashes then turns back on... I tried holding home and volume up. Home and volume down. home and volume up and down in the middle. I tried volume up, volume down. I have charged this for quite a while also, few hours. I also have a Jig that works with the s3 to go to download mode, that did not work.
I think if I can get to download mode I can get working again, but have not been able to get to that. Any help please? Thank you in advance.

jaredlappa said:
Hope this is ok area to post this in. I am having a problem with Tab 4 T230NU wifi only. I am trying to get to download mode to flash with Odin, but I can not? It flashes on with screen. "Firmware Upgrade encountered an error an issue. Please select recovery mode in Kies & try again. " It just flashes then turns back on... I tried holding home and volume up. Home and volume down. home and volume up and down in the middle. I tried volume up, volume down. I have charged this for quite a while also, few hours. I also have a Jig that works with the s3 to go to download mode, that did not work.
I think if I can get to download mode I can get working again, but have not been able to get to that. Any help please? Thank you in advance.
Click to expand...
Click to collapse
You are in download mode

Help!
Okay so I've been trying to root my Galaxy Tab 4 and everything I attempt fails, its stuck on ODIN mode and I cant seem to root it, recover it or anything. I need help

Devon S said:
Okay so I've been trying to root my Galaxy Tab 4 and everything I attempt fails, its stuck on ODIN mode and I cant seem to root it, recover it or anything. I need help
Click to expand...
Click to collapse
D,
while in odin reflash your custom recovery for your device with auto/restart checked.
odin will remain stuck in that mode until it restarts after successfully flashing an image.
m

This worked for me I was in soft brick I don't know if this will for you
1.download Odin v3
2.download twrp (sm-t230)
3.connect your tab to your PC and turn it on (make sure you have drivers installed)
4.you should see ADDED! ON ODIN (if you don't see it you probably didn't install the drivers correctly) click PDA and select the twrp rar file 5.wait for it to flash it (your tab may or may not reboot wait for Odin to say done or succeeded)
6.download a stock ROM for your tab
7.move the stock ROM onto a SD card
8.put SD card into tablet and mount it
9.tap install and look for the stock ROM
10.you may need to clear dalvik cache and/or data
I hope it helped. Pm me if you need help were to get the drivers and the stock ROM I'll be glad to help!
Sent from my SM-T230 using XDA Free mobile app

Bricked phone: Tried from CM to official 5.0

Hey guys,
I unfortunately bricked my device:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Information from the top left corner:
ODIN MODE
PRODUCT NAME: GT-I9505
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x1
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enable
eMMC BURST MODE enabled
The center text:
Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again.
The current ROM was Dirty Unicorn Lollipop and I wanted to flash the original samsung firmare.
After I flashed my phone restarted like this. I tried some things to flash via odin now, even my phone won't boot into recovery again.
Could someone help me what to do now? As I said I tried a few things from other guys with like the same problem.
I downloaded a package "I9505XXUHOA7_OXAHOA7" with CP, AP, CSC, PIT and BL but it didn't work as well.
Sincerely,
mrclaver

Flashing a stock ROM via Odin, with the ROM loaded in the BL slot, should restore your S4. You'll want to check your cable and make sure it's the original, and that it's plugged into the computer, not a hub. Use a different port if necessary.

Would you be so kind to give me a link to a rom you suggest I should try? Because the original ones I downloaded had five different files.
Sent from my SM-G900F using XDA Free mobile app

The rom should be only one of the files. The other files are something else.
Generally, you can get stock roms from sammobile. But their download speeds are excruciatingly slow..

GDReaper said:
The rom should be only one of the files. The other files are something else.
Generally, you can get stock roms from sammobile. But their download speeds are excruciatingly slow..
Click to expand...
Click to collapse
Yeah, but which file is necessary for flashing via odin? CP, AP, CSC, BL? AP is for PDA I think.
Sent from my SM-G900F using XDA Free mobile app

The .tar.md5 file. Put it into AP to flash.

Strephon Alkhalikoi said:
The .tar.md5 file. Put it into AP to flash.
Click to expand...
Click to collapse
This is what odin says:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_I9505XXUHOA7_CL3996895_QB3867680_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
This was after I tried to flash the ap file in PDA.
This is the official rom: I9505XXUHOA7_OXAHOA7
And these are the files which were in there:
I was thinking of using antoher usb port maybe? I hope it'd be that easy.

Odin is telling you that you have no PIT partition. That means you'll need to use a PIT file with the 2.4GB MD5 file in AP to flash. The PIT file can be found on the forums, along with instructions for using it.

mrclaver said:
This is what odin says:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_I9505XXUHOA7_CL3996895_QB3867680_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
This was after I tried to flash the ap file in PDA.
This is the official rom: I9505XXUHOA7_OXAHOA7
And these are the files which were in there:
I was thinking of using antoher usb port maybe? I hope it'd be that easy.
Click to expand...
Click to collapse
In 99% of the cases that error is caused by using a "wrong" usb port. Try all the ports on your pc and/or try a different usb cable.

You guys are awesome! It really was a wrong usb port! I tried then with AP in PDA but it wasn't successfull. So I decided to use all four files (AP, CSC, CP and BL). It took more than 10 minutes in odin but then it finally started! Thank you so much! Thread can be closed!

@Lennyz1988: I did mention switching USB ports, but I forgot to remind mrclaver of that. So leave it to me to forget the obvious.
@mrclaver: Glad everything worked out.

Odin3 v3.13 - Complete(Write) operation failed. S7 Edge - PDA G935FXXU2EREM

I've been having problems with my phone after the Oreo update. (freezing / bootloops / random restarts)
Already did a factory reset on my phone but the issue was not fixed so I've decided to flash my phone but I'm having problems.
Details
Phone - SM-G935FD - Non Rooted
Software: Odin3 v3.13.1 - Downloaded from https://dl.sammobile.com/Odin3-v3.13.1.zip
Only Auto Reboot and F. Reset Time are ticket - Pit tab not changed. Loaded BL AP CP and CSC/HOME_CSC from firmware below.
Firmware - GALAXY S7 edge / SM-G935FD - PDA G935FXXU2EREM - Downloaded from https://updato.com/firmware-archive-select-model?record=36A47F5A6E2711E89F15FA163EE8F90B
After several retries, ODIN still fails to flash my phone. It gets stuck at system.img
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> skip file list for home binary
<ID:0/005> param.bin
<ID:0/005> modem_debug.bin
<ID:0/005> Home Binary Download
<ID:0/005> Total Binary size: 4200 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Hope you guys can help me out. Thanks!

What is the Phone model on the back of ur phone
SM-935what
Is your phone rooted?
Possibilities are that the firmware and your phone are non compatible also send a screenshot of your odin.
You might have the wrong version selected.
Usually if your getting bootloops it's best to flash 1 checkbox at a time.
Make sure the port doesn't say com 3.
Com4 or com7 is OK.
The boxes don't really matter except the boxes u are flashing like the ap cp bl and csc
If your phone is 935fd then it is also compatible with 935f firmware which is more updated latest version is ERG2. Dual sim functuality is the same.

pingufanpoy said:
What is the Phone model on the back of ur phone
SM-935what
Is your phone rooted?
Possibilities are that the firmware and your phone are non compatible also send a screenshot of your odin.
You might have the wrong version selected.
Usually if your getting bootloops it's best to flash 1 checkbox at a time.
Make sure the port doesn't say com 3.
Com4 or com7 is OK.
The boxes don't really matter except the boxes u are flashing like the ap cp bl and csc
If your phone is 935fd then it is also compatible with 935f firmware which is more updated latest version is ERG2. Dual sim functuality is the same.
Click to expand...
Click to collapse
Thanks, my phone is a SM-935FD stock before I tried all of this.
I'm using Com4. In the screenshots I'm trying to flash to older 7.0 firmware.
By one checkbox at a time you mean I can uncheck BL after success right?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Would it be ok to flash to SM-G935F firmware even if my phone is carrier locked?
Thanks

dhysics said:
Thanks, my phone is a SM-935FD stock before I tried all of this.
I'm using Com4. In the screenshots I'm trying to flash to older 7.0 firmware.
By one checkbox at a time you mean I can uncheck BL after success right?
Would it be ok to flash to SM-G935F firmware even if my phone is carrier locked?
Thanks
Click to expand...
Click to collapse
You can flash oreo 935f firmware on a 935fd but your phone will still be locked to smart sim.
The only way to unlock your sim imei would be to pay the company around 150 usd on average usually most companies won't do it because of money and people terminating their contracts early.
You will still be able to call and text from your smart Sim.
Just flash the CSC named SMA after installing if you want the smart branding it's not necessary tho.

pingufanpoy said:
You can flash oreo 935f firmware on a 935fd but your phone will still be locked to smart sim.
The only way to unlock your sim imei would be to pay the company around 150 usd on average usually most companies won't do it because of money and people terminating their contracts early.
You will still be able to call and text from your smart Sim.
Just flash the CSC named SMA after installing if you want the smart branding it's not necessary tho.
Click to expand...
Click to collapse
Thanks, I'm downloading the 935f oreo version.
Specifically this one: https://updato.com/firmware-archive-select-model?record=489AC01E8C1E11E89F15FA163EE8F90B
Hopefully it works, will post back here later

Unfortunately it still failed. Anything else I can try?

https://forum.xda-developers.com/showpost.php?p=77167218&postcount=14

ajox said:
https://forum.xda-developers.com/showpost.php?p=77167218&postcount=14
Click to expand...
Click to collapse
Thanks! Tried it but mine fails at the AP part I think.

download lastOdin3_v3.13.1

Fixed this. It was a USB cable issue.

What did you have to do?
dhysics said:
Fixed this. It was a USB cable issue.
Click to expand...
Click to collapse
Hey
I have a similar issue. The process starts and then just freezes, always in the same spot. I haven't even gotten through the BL file yet. At this point I don't mind if I have to completely wipe the phone and start over, I just want it to boot again.
I've tried with 2 different cables, though neither is an "original" cable as that one broke ages ago. Any tips?
Code:
<ID:0/009> Added!!
<ID:0/009> Odin engine v(ID:3.1401)..
<ID:0/009> File analysis..
<ID:0/009> Total Binary size: 5 M
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> NAND Write Start!!
<ID:0/009> SingleDownload.
<ID:0/009> sboot.bin
<ID:0/009> param.bin
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

dhysics said:
Fixed this. It was a USB cable issue.
Click to expand...
Click to collapse
Hi there
Do you know what cable you used? I am using a mixture of original Samsung cables but not sure if they are for the galaxy s7, probably S5 days.