Car:Kia Sorento 2010
Head Unit: Pumpkin Android CN10
Android version: 6.01
Processor: quadcore-R16
Model / SKU: CN10-02201b-02A
Audio stopped working across the board. Turned out to be pre-amp in car so wired speakers straight to the stereo.
ON reboot no bluetooth.
I flashed from 'V7.3.2_20170826.102252_KED1' to 'V7.3.2_20170826.102252_KED1-mod' hoping for a bluetooth fix but no joy.
Does this sound like the bluetooth module is kaput or just not quite the right mcu firmware? Or???
some progress
So i got it back momentarily.
In extra settings (password 123456) i went to config info and set b6 and b8 checkboxes to ticked. Rebooted working.
Then rebooted and screen resolution was too large. fixed this with firmware from pumpkin bods.
However I cannot get B6 and B8 settings in config info to save together. It will only allow b8 to be checked.
Infuriating. Having b6 and b8 on is what fixed bluetooth but they will not save.......
Any ideas on how to get the config info to save?
Solved bluetooth issue
So managed to solve bluetooth issue.
Under extra settings changed the model to my car (Kia/Hyundai), let it reboot.
Then reset thru pin hole reset button.
Bluetooth is back.
Didn't seem to matter which rom.
Just steering wheels controls dont work whereas they did once.
hth someone
Related
Hi There,
I have an VW Touareg I from Year 4/2008. It is the Facelift Model with CANBUS 2.0
Buy a Erisin 5056T Unit (PX5 / 2 GB) with integrated VW CANBUS Decoding Box (Decoder inside the Radio it´s not external Box).
Inside the Unit i try different Types of CANBUS settings (Default was 1 (VW / Scoda))
I am little Frustrated because of the limit Implementations of decoding CANBUS Signal inside this Unit.
Whats running:
ACC Signal (Radio turn on when i plug IN the Car Key and go into "Sleep Mode" when i pull the Key out.
Steering Wheel Keys: Only Loud / quiet / Phone / Mute keys are running (can´t change any Responsible of keys in the Unit) seems hard coded
Screen for Camera Switching if i switch my gear into Reverse
Whats not running:
NO , really no Data inside the vehicle App.
Reaktion of draw lines for the backwards Camera change/move only when i turn 100% left or Right on the Steering Wheel. And only for millimeters....
Is there any Experience with other Units that can better Communicate with VW Touareg?
Regards
Ben
no one use a Android Car Unit in the Touareg ?
http://backly.ru/go/1f7n
Hi
Thx for response.
Did you have experience with that Unit?
Can the Radio read the Door or/and Park Sensors?
Regard
Ben
ben97 said:
Hi There,
I have an VW Touareg I from Year 4/2008. It is the Facelift Model with CANBUS 2.0
Buy a Erisin 5056T Unit (PX5 / 2 GB) with integrated VW CANBUS Decoding Box (Decoder inside the Radio it´s not external Box).
Inside the Unit i try different Types of CANBUS settings (Default was 1 (VW / Scoda))
I am little Frustrated because of the limit Implementations of decoding CANBUS Signal inside this Unit.
Whats running:
ACC Signal (Radio turn on when i plug IN the Car Key and go into "Sleep Mode" when i pull the Key out.
Steering Wheel Keys: Only Loud / quiet / Phone / Mute keys are running (can´t change any Responsible of keys in the Unit) seems hard coded
Screen for Camera Switching if i switch my gear into Reverse
Whats not running:
NO , really no Data inside the vehicle App.
Reaktion of draw lines for the backwards Camera change/move only when i turn 100% left or Right on the Steering Wheel. And only for millimeters....
Is there any Experience with other Units that can better Communicate with VW Touareg?
Regards
Ben
Click to expand...
Click to collapse
Same here, mine is a px3 android 7.1....... any luck? Have you been able to fix it? My backup diplay works perfectly on ford focus canbus setting....
Hi
Inside the Unit i try different Types of CANBUS settings (Default was 1 (VW / Scoda))#### do you still use this one??
I am little Frustrated because of the limit Implementations of decoding CANBUS Signal inside this Unit.
Whats running:
ACC Signal (Radio turn on when i plug IN the Car Key and go into "Sleep Mode" when i pull the Key out.
Steering Wheel Keys: Only Loud / quiet / Phone / Mute keys ##### mine just rhe volume works.
##### if i press Phone in the stering wheel it just play next sont
####the star key in the wheel does nothing
Can you help?
2006 touareg
Thank you
Hello guys,
I have the exact same problem with a Erisin PX5/4gb/Android 9.0, but I have a Treg from 2005 with Canbus 1.6. I have contacted Erisin, sent them my original wiring diagram and am waiting for their response. in the meantime I have the latest MCU updates, I'll try them today.
Have you tried the Canbus setting VW_TOUAREG(Hiworld) ? For me it doesn't work, but maybe for those of you who have Canbus 2.0 will work.
If I find a solution or I have any news I'll post them here, hope you do the same, maybe we will get this unit to decode all the signals from Can-Bus.
If anyone wants the updates images, just let me know and I'll upload them.
Regards,
O
Good afternoon,
Hi need help with my headunit, I Have an Audi A4 b6 and seems the canbus stopped working.
Yestarday when I left the car in my garage, the heaunit was working, but this mornig when I get to the car the same started with the car but doesn't have sound, radio, music, volume,it seems that configuration won't save. I have access to factory configs but the selections I make on canbus aren't saved...
I made this video to the seller, I have the radio working about a year more or less
Does anyone have ideas
Hi all ,
can anyone give a hand in this problem :
I just bought an android head for peugeot 307 year (2007) canbus version , comes with Raise canbus
version PSA-RZ-15
sw: V0103
hw: VW-NC03
works fine and read car info but suddenly after changes some car models protocols, it disconnected, even if I choose the previous car model.
in System Info. gives the canbus model : (Peugeot 408.disconnected) !!!
I did a factory reset and change the canbus model many times without any success.
Now every things related to canbus is not working (Wheel buttons ,Fuel info ,Reverse Radar ,etc.)
what should I do?
Thanks in advance.
i have same problem in 2022 with peguet 301 model 2015 and use hiworld can bus
i have the same problem with hiworld canbus it didnot work every time mostly disconnected
I had some issues with my car Android head unit and I probably played in the wrong places and now I ended with no sounds coming from the radio, but sound is coming from the Bluetooth.
The units run Android 4.4.2 on a Mstar cedric3 unit (with cortex-A9 dual core). The car is Suzuki Vitara 2016.
Before I played with the settings the radio worked.
While trying to fix some other issues, I did quite allot of stuff: factory reset, changed the MCU, changed some settings. Some where along the way I realized that the radio stopped making any sound.
To fix the radio I tried to get the MCU back to the version it was in the beginning (4.3.14-11-10-456101-150712) but apparently inside the unit I could not find this version.
I searched of this MCU file on the internet but could not find it.
There is also an option: settings -> general -> extra settings -> radio antenna power, but when I change its value to “open” it go back to “close”
Any idea what is the source for the radio not playing?
I really need your help in getting it back on.
Hello everyone,
I'm have no experience installing and configuring android head units. Got myself one from Aliexpress, Essgoo AZ0001C, that's how they labeled it. I'm trying to install it in Opel Astra H 2009.
Here are some specs:
Android 10
2GB ram
32GB storage
Alps Q92
Platform AC8227L
Car audio: F7.3.7
CAN Pro: V9.0.6 (disconnect): Oudi-Opel
MCU: 4.0
Tried to find in which forum category to put it, but cannot find any more info about MCU except 4.0
My problem is can bus "disconnect" which I assume means there is no communication with the car. Head unit works, GPS works, Playstore, Radio, turns on/off with the car, but cannot program steering wheel buttons, no reverse camera detection, no any board computer info.
I tried going into Factory settings (with password 8888) and found Astra H multiple times in Protocol settings:
Raise - Opel - 08~10 Astra H
Xinpu - Opel
Oudi - Opel
Luzheng - Opel - Andra (was set by default when arrived)
KBS - Opel - 08~10 Astra H
BaoGood - Opel
Can Bus Decoder has this:
RH 20220920
For OPEL
HW: V5 SW: V2
QFN32_16PIN-BOX_V1.1
Basically, I tried selecting every option for Opel in Protocol settings, but without success. Am I missing some setting, or it could be hardware issue, or ?
Just if anyone reads the topic in the future and has the same unit. There are a lot of similar units out there, Chinese cheap head units often use similar chipset. It's old, slow, but can do the work if your expectations are low.
I think I managed to set up everything.
In Factory settings choose "Xinpu - Opel".
Can bus still say "disconnect" but it's not that important.
Map steering wheel commands, it will say failed, but controls will work.
For reverse camera, find brown wire going into black head unit connector (16 pin) and connect it to wire from back light. My camera cable has this wire, it will be 12V when reverse gear is engaged, below 1V when not.
Head unit will not shut down when car is turned off, it will just enter sleep state and drain your battery slowly (consumes around 5W). To prevent it, go to Factory settings with password 8888, select "Engineering test debugging" and enter password 26959910, select "direct shutdown mode". It will shutdown completely when car is turned off, after 30-40 seconds.
Hope it helps someone.