Phone : Yureka AO5510
OS : Wiped Already
Recovery : Cynogenmod
Incident: Once in a sudden phone got stuck (Saw something like "Trebuchet Stopped Working") and I tried to force shut down, After restart the phone was not working. Tried to flash but i got these error messages "E:Footer is wrong" and Signature verification failed (Previously I have used CM12,13 and Lineage OS 14.1 all were working).
Android Debugging was not enabled, I can enter fastboot mode. but not accepting any commands.
Either I have to enable USB Debugging, or Need to overwrite the recovery with TWRP or CWM, so far all flashing resulted with the above error messages.
Any help would be appreciated. Ready to buy a coffee if I succeed (India).
Try to flash cm-12.1-YOG4PAS8A4-tomato-signed-fastboot.zip via fastoot.
It doesn't need USB debugging to be enabled.
saurav007 said:
Try to flash cm-12.1-YOG4PAS8A4-tomato-signed-fastboot.zip via fastoot.
It doesn't need USB debugging to be enabled.
Click to expand...
Click to collapse
hey!! even i had similar problem i tried the method you mentioned following this guide
http://www.thetechnotriad.com/326/how-to-root-yu-yureka/
the phone is working good the only major problem whatsapp is not opening...when clicked opens for 0.01 sec and returns back to previous screen (flashes) ....please somebody help me with this. Thanks in Advance.
56s
Red sir
I purchase yureks AO,5510 mobile from your web and your site.But today it is not working in what up app and we will try again and again but sorry to say problem is not solved.
And in yureka mobile when power off and again power on then it is not start we try so many time .
So think that is totally cheating with us from Google and yureka company.
Related
Dear sir,
i tried to factory reset my phone and when phone rebooted YU logo shown up but after that nothing happened ,it didn't load up,black screen,shut down again.(SOFT BRICK).
i tried many attempts to install stock recovery using fast boot mode,but in cmd it ends up showing waiting for device.
i think usb debugging was disabled,that's why it is showing waiting for devices,and hence i cannot install stock recovery and reboot my phone. So is there any way to fix "waiting for device" ,is there any way to enable usb debugging even if i cannot start my phone . I need your your help ASAP.
3skanurag said:
Dear sir,
i tried to factory reset my phone and when phone rebooted YU logo shown up but after that nothing happened ,it didn't load up,black screen,shut down again.(SOFT BRICK).
i tried many attempts to install stock recovery using fast boot mode,but in cmd it ends up showing waiting for device.
i think usb debugging was disabled,that's why it is showing waiting for devices,and hence i cannot install stock recovery and reboot my phone. So is there any way to fix "waiting for device" ,is there any way to enable usb debugging even if i cannot start my phone . I need your your help ASAP.
Click to expand...
Click to collapse
yes it is soft brick. i face same problem. but make sure your pc has successfuly installed adb drivers.
if drivers are not working so you will see waiting for device.
It is fixed now i used pdanet+ then adb then flashed cm recovery then removed battery and plugged in and then it started.
3skanurag said:
It is fixed now i used pdanet+ then adb then flashed cm recovery then removed battery and plugged in and then it started.
Click to expand...
Click to collapse
i have solution for soft brick. download fast boot stock images and follow procedure.
Link for fastboot rom
Link for tool and guide in this link you will see procedure also just scroll down in this page
ashish_zarekar said:
i have solution for soft brick. download fast boot stock images and follow procedure.
Link for fastboot rom
Link for tool and guide in this link you will see procedure also just scroll down in this page
Click to expand...
Click to collapse
i tried the method you mentioned following this guide
http://www.thetechnotriad.com/326/ho...oot-yu-yureka/
the phone is working good the only major problem whatsapp is not opening...when clicked opens for 0.01 sec and returns back to previous screen (flashes) ....please somebody help me with this. Thanks in Advance.
guys i have softbricked my lenovo a6000 and its stucked on lenovo logo
i have tried adb method to flash back recovery mode but when i rum commands it gives error == device null found
when i connect my device to pc it makes an connected sound help me out of this as this is the only mobile i was having
plzzzzzzzzzz guyzzhelp me out
Bro need help I installed twrp and then cm 13 on my a6000 and by mistake I deleted backup of my stock kk rom and now when I try to go in download mode, recovery it doesn't open it show only Lenovo logo . By mistake I flashed a6000+ stock recovery and after that when I try to flash stock recovery of a6000 using adb nothing open .. so now nothing download mode or recovery mode is opening but i still boot into cm13 how solve it to revert back to kk ?
Solution
Shubhamraaj said:
guys i have softbricked my lenovo a6000 and its stucked on lenovo logo
i have tried adb method to flash back recovery mode but when i rum commands it gives error == device null found
when i connect my device to pc it makes an connected sound help me out of this as this is the only mobile i was having
plzzzzzzzzzz guyzzhelp me out
Click to expand...
Click to collapse
I had also stuck in boot logo once in a custum ROM .
but i fixed it : steps .
Download twrp recovery in your pc. ( rename it as twrp.img ) ,
Boot your phone in to fastboot mode .,
Make sure ur pc has ADB drivers ,
Once , phone get into fastboot mode ,
Type this Commands : 1)fastboot devices ( to check if ur phone is getting detected or not , if it shows no device found , check connection )
2) fastboot flash recovery twrp.img ( to flash recovery)
3) fastboot reboot recovery ( to boot into recovery )
4) download any ROM to SD card and flash it from recovery.
Hit thanks button if this helped you.
Hello guys I have a6000 (Lenovo)
But my problem I saw this video
. Which is easy to revert back to kk rom but I have installed twrp which is not useful for above video method .so when I try to to install Philly or cwm which is used in above video it not installing only twrp will installing other custom recoveries not installing so please help me!!! If anybody have the twrp backup of stock kk rom of a6000 please send me!!
My lenovo a6000 also got stock on boot logo in a custom rom. Its now in no use. Now when i try to connect ut to my pc, its only charging. My device is not being connected to pc. Now what to do ??
Androidsabya said:
My lenovo a6000 also got stock on boot logo in a custom rom. Its now in no use. Now when i try to connect ut to my pc, its only charging. My device is not being connected to pc. Now what to do ??
Click to expand...
Click to collapse
FOLLOW THIS
Need help
sasukay said:
FOLLOW THIS
Click to expand...
Click to collapse
Actually 1st i did root my lenovo a6000. Then i was trying to install cyanogen rom through sd card. But it showed e verification failed. And while booting it gets stock showing cyanogen logo. I tried my phone to connect to pc, but it only charges my phone but doesn't show up in connected device in my laptop. I went to an mobile repair shop, bcoz i thought may be i was missing something. But after visiting 3 repair shops, they also couldn't solve my problem. Now how can i get my mobile to back condition ? Need help. If anyone can help plz give quick rply. But i need to talk to someone who can help regarding this issue. So if you can talk to me, plz call me 7008678740. Thank. Plz give response.
New problem arrised
sasukay said:
FOLLOW THIS
Click to expand...
Click to collapse
I could successfully restored my lenovo a6000 kitkat rom. But a new problem arrised. When i try to power on, it just starts for 2 seconds and vanishes immediately just showing the lenovo logo. Again n again it just being on and off. When i put this battery in another a6000 plus mobile, the same problem occurs. I mean , i want to know why is this happening ? Is the battery gone !!!
Androidsabya said:
I could successfully restored my lenovo a6000 kitkat rom. But a new problem arrised. When i try to power on, it just starts for 2 seconds and vanishes immediately just showing the lenovo logo. Again n again it just being on and off. When i put this battery in another a6000 plus mobile, the same problem occurs. I mean , i want to know why is this happening ? Is the battery gone !!!
Click to expand...
Click to collapse
On first look, it seems like your phone is in bootloop and you need to flash new ROM after wiping the partitions correctly. But, then you are saying that same thing is happening when you insert this battery in another A6000. I think your battery has gone rogue due to some virus, just throw it away. Jokes apart, if another device is showing same behaviour then its almost 100% sure, that your battery has issues and need to be replaced. And, why don't you actually check switching on your phone by putting the battery from that another A6000 into your A6000.
I have checked with another battery, my phone works fine. But that particular battery is doing only on off continuously. But #important thing is , i don't think the battery has gone. Bcoz during the on off process, if i press volume down key, it shows lenovo logo and gets stock there. If the battery has problem, then how can be it stays on showing the logo ?? Confused ???
Hi all,
A strange thing happen to me, my Zuk Z1 ran out of battery and I've put it to charge and when I boot it up again it kept boot looping.
My Zuk Z1 is the international version and I have tried all of the below solutions
Clear all caches and media - No luck
Use QFIL with original rom - No luck keeps boot looping and most of the times gives an error at the very end of the QFIL ( Download Failed QDloader .... )
Used QFIL with ZUI rom - Works but most of the functions don't work, no wifi, bluethooh and so on
Erased sdl1 with fastboot ( that made the phone to seem dead, had to open it and remove the battery in order to be able to install QFIL rom again )
ADB sideload, stops at 47% everytime and the phone reboots and keeps doing the boot loop.
I can get ADB and Fastboot working but I'm running out of ideas!
Also I was thinking on rooting the phone to allow me to install Cyanogenmod to see if it works but don't know how to achieve this, Kingroot needs internet and I have no way of getting it to work.
Any idea would be very welcome !
Thanks
UPDATE:
I was able to flash TWRP and CYANOGENMOD 13, it boots but its the same as in ZUI, no wifi or bluetooth, I'm guessing it was the motherboard that fried !? The mac address displayed on the WLAN is 02:00:00:00:00:00 and i've tried several options in developer mode which didn't work.
Click to expand...
Click to collapse
I have lenova a6000 8 gb black phone
I have problem when i went to do factory reset because of network problem.but it stuck on erasing screen and moght be goes in loop as its shows erasing screen frequntly and cant start any mode or normal os.what should i do. I tried to connect to pc but it was never detected in any pc .
Give solution
Hear is link for problem video
Youtu.be/sTajWR7OV6Y
mrohb12 said:
I have lenova a6000 8 gb black phone
I have problem when i went to do factory reset because of network problem.but it stuck on erasing screen and moght be goes in loop as its shows erasing screen frequntly and cant start any mode or normal os.what should i do. I tried to connect to pc but it was never detected in any pc .
Give solution
Hear is link for problem video
Youtu.be/sTajWR7OV6Y
Click to expand...
Click to collapse
Did you installed drivers for your lenovo a6000 In your PC.
If no install driver and install twrp and erase your data
Still problem remaining
Yess i have installed lenoa usb driver for this mpbile but its not detected even in device manager also.
I have also ttied using port setting but still problem remaining.
Can u say another method to detection
mrohb12 said:
I have lenova a6000 8 gb black phone
I have problem when i went to do factory reset because of network problem.but it stuck on erasing screen and moght be goes in loop as its shows erasing screen frequntly and cant start any mode or normal os.what should i do. I tried to connect to pc but it was never detected in any pc .
Give solution
Hear is link for problem video
Youtu.be/sTajWR7OV6Y
Click to expand...
Click to collapse
I am really sorry to hear about what's happened.
You may consider flashing the stock ROM of your Lenovo A6000 to resolve the issue.
If you prefer the KitKat ( Which I highly recommend. I tried all kinds of Custom ROMs for years but now I am back to the stock, it's the best and the most compatible for our device. ), you can download the package from the link given below. All the tools needed are there including the instructions.
Code:
http://www.mediafire.com/file/vlw8t6yv0jzay1b/Lenovo_A6000_S040_150805_8G_ROW_by.reda%40gem-flash.com.zip
However, if you wish to flash Lollipop stock ROM which has many bugs, you can download the other package below. It also includes instructions and tools needed.
Code:
http://www.mediafire.com/file/dhwu78g9llbv133/Lenovo_A6000_S062_Q102113_20161223.zip
If you are still having problems, please let me know. I may be able to help you further.
Regards,
xda_borj
I think I have an unsolved problem. I know it doesn't exist, but it's very hard to find it.
I know it's not the Plus, but the Model is the Moto C XT1754 (NAMATH) Android 7.0 Nogaut - NRD90M.060
And there is no specific topic for it, but they are very similar and I thought I could post it here.
It's a very complicated problem, so I'll explain in detail what happened and why I had to come here to solve it.
(translated)
- STARTING:
I installed a TWRP through the app, without unlocking the Bootloader.
Whenever I turned it on, at boot still, the message appeared:
'red state
Your device has failed verification and may not work properly
Your device will boot in 5 seconds'
But it called normally.
I installed 'Magisk Manager 24.2' by zip and app afterwards.
I activated 'Zygisk' and in DenyList I activated/hidden from Google Play Services completely. All.
I restarted the smartphone and Sitema started having numerous errors. Most of the apps that I opened, closed with error, and other apps in the background too, mainly Google Play Services.
I tried to solve this but I couldn't because the smartphone was unusable.
I decided to format by TWRP.
But when I tried to restart the device, I always entered TWRP and continued that message in Boot ('Red State Your Device...')
I decided to reinstall Stockrom from Moto C XT1754.
When I tried to install Stockrom through flash_tool, I couldn't.
It always gives error.
'BROM ERROR : S_BROM_CMD_STARTCMD_FAIL (0x7D5)
[BROM] Can not pass bootrom start command! Possibly target power up too early.
[HINT}:'
or this one is the most common:
'BROM ERROR : ?? (0x1)
[HINT];'
I even tried installing a Custom Rom via Sdcard , 'Viper-namath-20171206-Coral-v3.1.1-UNOFFICIAL' with the GAPPs, etc.
I can install the ROM. (but the GAPPS gives an error at the end of the installation) 'open_gapps-arm64-7.1-micro-20220215'
But I think this case is because it is not installing the Custom ROM correctly. (Because of the Locked Bootloader? Maybe... I'm kind of a layman on the subject)
Because when I restart the device after installation it goes back to TWRP.
I can't get into Fastboot mode with the command by the buttons on the device, only by TWRP when I access 'Reboot>Bootloader'.
Reboot and go to fastboot (Black screen, down there written '=> FASTBOOT mode...'
I've already tried to recover/rescue the device by Motorola/Lenovo's 'Rescue and Smart Assistant'. But when I try to rescue it (with it connected to TWRP) it asks to accept the message to enable USB debugging.
But I don't have access to this window through TWRP.
Here comes the big question, why I am not able to solve my problem:
I think my 'USB Debugging' was off/disabled before I erased everything (formatted).
I'll try Stockrom's Flash through TWRP to see if it solves the problem, but I don't think it will.
I think the problem may be with the 'USB Cable' as well. He's old. I tested with a non-original USB cable that I had to see and I can't either, the errors persisted.
I plan on getting another original to test as well.
Just an observation.
My device is being recognized as 'USB MTP Device' (under 'Portable Devices')
If anyone can save me, I'd really appreciate it!
Thanks in advance for all the help! Every opinion matters!
And when I give the command 'ADB Devices' my device appears 'unauthorized'
'ZW3223CGWK unauthorized'