Related
Requirement :
Should haveWugfresh Nexus Root Toolkit installed on your computer [with all updates installed ( not necessary),Should wait for it to download necessary updates for your device ( If no net connection then also no prob just wait) ]
( To download nrt visit wugfresh site(can't post link soory) )
You should how to connect your device using nrt, else, follow these steps,
Navigate to about phone section, while you are in the About Phone section, click on the Build Number option seven times to enable Developer mode. Then,go back to settings menu scroll down to developer options, in the Developer mode options, enable USB debugging. A screen will pop up on your phone when the program attempts to make a connection. Make sure to allow it.
Installing drivers :If the program and computer aren't recognizing your device, you will have to install software drivers. In the Nexus Root Toolkit, click on the "Full Driver Installation Guide" button and follow steps one to four. This is the most difficult part of the process. Be sure to follow the steps exactly.
Should know how to boot into bootloader.( can't post a link on where to find out sorry)
How to find if your nexus is bricked:
You see a message "Boot failed...." on your device.
The device is not booting but is staying on boot animation screen for long time (>30 minnutes).
The device is bootlooping means the device is rebooting again and again upto boot animation.
And any other problem that might result in your device, not being able to boot.
What you should do:
Don't panic this error is 100% rectifiable.
if you happened to end up in "boot failed" message on your device after the computer you were using switched off halfway through the flashing process.Then you have to restart your computer and then boot your nexus into bootloader mode and connect it to your computer.
Open Nrt ( Nexus root toolkit)
You should select change in your model type and set "select the android build you are currently running to the version of android you were trying to flash if you were trying to flash some other ROM, then just leave this step.
Then select "soft-bricked or bootloop" or "device is on or normal" depending on your device's current state and press on "Flash stock + Unroot".
you will have to either download a factory image and browse to it when asked so by the software, or let the software download it for you.
( For obtaining factory image for your nexus and search for your device based on build number of your device... )
All the screen on your computer read and do as necessary (Most of the times it is "OK" button that you have to press)
The device should be back to normal after it reboots.
Else just let me know......!
This can be done without a toolkit, Flashing factory image with fastboot instead.
Toolkits cause many of the issues on here, learning to do it manually with fastboot can both avoid issues, and fix issues. And teach people valuable skills.... As adb/fastboot are essential tools, especially with a Nexus. ?
But thanks for the info. Contributions like this are always good. ?
Problems with "Boot Failed"
visnkmr said:
Requirement :
Should haveWugfresh Nexus Root Toolkit installed on your computer [with all updates installed ( not necessary),Should wait for it to download necessary updates for your device ( If no net connection then also no prob just wait) ]
( To download nrt visit wugfresh site(can't post link soory) )
You should how to connect your device using nrt, else, follow these steps,
Navigate to about phone section, while you are in the About Phone section, click on the Build Number option seven times to enable Developer mode. Then,go back to settings menu scroll down to developer options, in the Developer mode options, enable USB debugging. A screen will pop up on your phone when the program attempts to make a connection. Make sure to allow it.
Installing drivers :If the program and computer aren't recognizing your device, you will have to install software drivers. In the Nexus Root Toolkit, click on the "Full Driver Installation Guide" button and follow steps one to four. This is the most difficult part of the process. Be sure to follow the steps exactly.
Should know how to boot into bootloader.( can't post a link on where to find out sorry)
How to find if your nexus is bricked:
You see a message "Boot failed...." on your device.
The device is not booting but is staying on boot animation screen for long time (>30 minnutes).
The device is bootlooping means the device is rebooting again and again upto boot animation.
And any other problem that might result in your device, not being able to boot.
What you should do:
Don't panic this error is 100% rectifiable.
if you happened to end up in "boot failed" message on your device after the computer you were using switched off halfway through the flashing process.Then you have to restart your computer and then boot your nexus into bootloader mode and connect it to your computer.
Open Nrt ( Nexus root toolkit)
You should select change in your model type and set "select the android build you are currently running to the version of android you were trying to flash if you were trying to flash some other ROM, then just leave this step.
Then select "soft-bricked or bootloop" or "device is on or normal" depending on your device's current state and press on "Flash stock + Unroot".
you will have to either download a factory image and browse to it when asked so by the software, or let the software download it for you.
( For obtaining factory image for your nexus and search for your device based on build number of your device... )
All the screen on your computer read and do as necessary (Most of the times it is "OK" button that you have to press)
The device should be back to normal after it reboots.
Else just let me know......!
Click to expand...
Click to collapse
Well I had a different kind of problem.
My Nexus was running fine in 4.4.4 when I rooted it since it was out of warranty. It upgraded to Lollipop 5.0 without a problem and continued to function in rooted state.
It made several attempts at updating to 5.0.2 but always ended with "Failed" message. I figured unrooting the device might help with the OS upgrade. It did not and screwed up everything. I then Set it to Factory default and it went to wiped 5.0 state. Then disaster struck. I tried rooting it , unfortunately with older Chainfire which bricked the device and would not let me install 5.0. So I tried to force install 4.4.4 and then the device got bricked. I simply get the message "Boot Failed" I boot into fastboot mode and I get the basic display with green start in the upper right corner, large Android icon in the center of the screen and the standard fine text on the lower let side. Unfortunately Windows ( x64 - Ultimate) insists on recognising the device as "Unknown Device" and when I go into properties this is is what is states ...
"Windows has stopped this device because it has reported problems. (Code 43)"
Do you think I might have better luck if I tried this on a Win XP machine ? I have both, x86 and x64.
Now, can you please tell me how I can get around this problem ?
BTW I do remember olden days of Cassiopeia PDAs before the flash memory came on the stage. The original OS would be on a plugged in masked rom daughter board in the event of losing all battery power. You could always force it to load it and get to factory mode. I think it is high time Android device manufacturers reverted to this process. I believe it can live side by side with the current system at a very marginal higher cost but have a whole lot of satisfied and LOYAL customers. It would give the user ability to go to factory mode albeit without any OS updates/upgrades but a fully functional device.
Would very much appreciate your feedback.
Hi guys,
a week ago my ZUK Z1 started to bootloop without any evident reason.
I found it in this state picking it up from my pocket, so I guessed it was due to some random reboot that occasionally happened to it.
So, stating that:
- I'm with original stock CyanogenOS,
- I never rooted, or even accessed to the recovery menu prior to this event,
- I'm perfectly able now to communicate and send commands to device via adb or in fastboot mode,
problem is that I did NOT enable "USB debugging" and I did NOT OEM unlock when I had the chance to reach Developer options menu through the Android GUI (now I'm blocked by bootloop), resulting in an obvious "no unlocked device" error message each time I try to flash or write system partitions.
The output from "fastboot oem get-info" confirms this status.
I'm operating from a shell with adiministrator's grant in Windows 8.
No luck with "fastboot oem unlock", "fastboot flashing unlock_critical" or "adb root".
I used also "-i 0x2b4c" (vendor code) option in my commands.
Then, my question for you:
is there still a way to unlock bootloader in order to recover with CyanogenOS stock image, in this condition?
I saw there's a "debuggable" image on Cyanogen site, but I've no hint on how to use it and if it could help me.
Maybe ZUK has to provide to me an unlock key: I read on this forum that OnePlus and Huawei have similar option.
Thanks a lot in advance for any hint and suggestion you can give to me.
---------- Post added at 05:43 PM ---------- Previous post was at 05:43 PM ----------
[/COLOR]
dalviking said:
Hi guys,
a week ago my ZUK Z1 started to bootloop without any evident reason.
I found it in this state picking it up from my pocket, so I guessed it was due to some random reboot that occasionally happened to it.
So, stating that:
- I'm with original stock CyanogenOS,
- I never rooted, or even accessed to the recovery menu prior to this event,
- I'm perfectly able now to communicate and send commands to device via adb or in fastboot mode,
problem is that I did NOT enable "USB debugging" and I did NOT OEM unlock when I had the chance to reach Developer options menu through the Android GUI (now I'm blocked by bootloop), resulting in an obvious "no unlocked device" error message each time I try to flash or write system partitions.
The output from "fastboot oem get-info" confirms this status.
I'm operating from a shell with adiministrator's grant in Windows 8.
No luck with "fastboot oem unlock", "fastboot flashing unlock_critical" or "adb root".
I used also "-i 0x2b4c" (vendor code) option in my commands.
Then, my question for you:
is there still a way to unlock bootloader in order to recover with CyanogenOS stock image, in this condition?
I saw there's a "debuggable" image on Cyanogen site, but I've no hint on how to use it and if it could help me.
Maybe ZUK has to provide to me an unlock key: I read on this forum that OnePlus and Huawei have similar option.
Thanks a lot in advance for any hint and suggestion you can give to me.
Click to expand...
Click to collapse
Sideload the official stock rom with zuk z1 tool. That s how i managed to un-brick my zuk. Download the stock rom , cm-12.1-YOG4PAS3OH-ham-signed.zip from this page https://cyngn.com/support. Use the toolkit provided here : http://forum.xda-developers.com/zuk-...alpha-t3235964 to sideload the rom. Wait until the phone restarts and thats it. You must also install adb and fastboot and have adb driver installed.I used the shenqi adb composite driver, but i guess the universal adb driver can work too. I had the same problem. Stuck in bootloop with USB debugging not enabled and bootloader locked.
Or you can try to fastboot the stock rom with the command provided in this useful tool.
Extentho said:
---------- Post added at 05:43 PM ---------- Previous post was at 05:43 PM ----------
[/COLOR]
Sideload the official stock rom with zuk z1 tool. That s how i managed to un-brick my zuk. Download the stock rom , cm-12.1-YOG4PAS3OH-ham-signed.zip from this page https://cyngn.com/support. Use the toolkit provided here : http://forum.xda-developers.com/zuk-...alpha-t3235964 to sideload the rom. Wait until the phone restarts and thats it. You must also install adb and fastboot and have adb driver installed.I used the shenqi adb composite driver, but i guess the universal adb driver can work too. I had the same problem. Stuck in bootloop with USB debugging not enabled and bootloader locked.
Or you can try to fastboot the stock rom with the command provided in this useful tool.
Click to expand...
Click to collapse
Thanks a lot Extentho for your feedback.
I've already tried your fair suggestion: unfortunately, I'm stuck at the end of sideloading the signed .zip.
In fact, I see on screen logs that it's applying the update "unconditionally" (that sounds good), but nevertheless, when finished it returns "xfer: 1.00x" on PC shell and in recovery menu, on device.
Now, either if I reboot or power down and boot it again, the result is the same: still bootloop-ing.
Of course, at any other attempts leveraging on administrative privilege, it says that "device is locked", including those done through the shell tool.
Some excerpts from my last launched commands:
c:\_APP\CM>adb devices
List of devices attached
51f8941d sideload
c:\_APP\CM>adb shell
error: closed
c:\_APP\CM>adb kill-server
c:\_APP\CM>adb root
error: closed
c:\_APP\CM>adb kill-server
c:\_APP\CM>adb usb
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
error: closed
c:\_APP\CM>adb kill-server
c:\_APP\CM>adb devices
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
List of devices attached
51f8941d sideload
c:\_APP\CM>adb sideload cm-12.1-YOG4PAS3OH-ham-signed.zip
Total xfer: 1.00x
You must have the phone in sideload mode. There is an option to sideload in recovery menu.
Then use the command to sideload from the toolkit. The stock rom must pe renamed sideload and placed on desktop.
If the phone communicates in any way with pc, there is still hope. When you start the sideload process from pc, the phone should show an animation showing the flashing process. Post some pictures from where you are stuck, so i can make an idea about what is going on
my zuk z1 stuck to bootloop,
and android debugging is disabled.
phone can not detecting in fastboot mode.
please help.
Extentho said:
You must have the phone in sideload mode. There is an option to sideload in recovery menu.
Then use the command to sideload from the toolkit. The stock rom must pe renamed sideload and placed on desktop.
If the phone communicates in any way with pc, there is still hope. When you start the sideload process from pc, the phone should show an animation showing the flashing process. Post some pictures from where you are stuck, so i can make an idea about what is going on
Click to expand...
Click to collapse
I've tried also with the toolkit, but it's heavy bugged (also in 5.4 version) and, after all, it gets the exact same problem like me (not surprising, it launches my same commands ).
There's no useful image or snapshot I can share, because I see the animated green android logo moving its antennas on my device, while logs below saying that it's verifying package and then it's unconditionally overwriting system partition.
It seems all so normal and plain.
At the end of the process, no "installation complete" message, but simply I get back to recovery menu (where I started from).
In other attempts, I also wiped cache and user data, prior to rebooting, just to test if it was going to change something, but no luck.
The phone reboots, the "Cyanogen" logo starts to glow for 7/8 times and then... bzzzz, short vibration and all over again (i.e. bootloop).
I tried with an older official signed .zip from Cyanogen OS (cm-12.1-YOG4PAS3AJ-ham-signed, instead of newer cm-12.1-YOG4PAS3OH-ham-signed), but even worst, it fails at "verify package" step, aborting procedure.
MD5 signatures triple-checked each time versus source.
I saw some threads where it seems possible to change the bit, on system image, controlling developer option, to manually post-enable unlocking, but it's suitable only for Nexus or OnePlus One. No instructions for ZUK Z1.
Or maybe do I need a "donor" sharing a stock .zip with this option yet enabled?
Bootloop would be still there, but I possibly could enable to "flash", "boot" and "shell" vs the device, giving me much more options to try.
One last doubt anyway. If I press "Volume Down" + "Power" button at boot, I get into a menu like this:
http: // postimg.org/image/s5badiefh/ (remove extra spaces).
Viewing other examples posted on forums, I noted that at least the "Factory reset" is missing.
Could it be an hint for anything useful?
dalviking said:
I've tried also with the toolkit, but it's heavy bugged (also in 5.4 version) and, after all, it gets the exact same problem like me (not surprising, it launches my same commands ).
There's no useful image or snapshot I can share, because I see the animated green android logo moving its antennas on my device, while logs below saying that it's verifying package and then it's unconditionally overwriting system partition.
It seems all so normal and plain.
At the end of the process, no "installation complete" message, but simply I get back to recovery menu (where I started from).
In other attempts, I also wiped cache and user data, prior to rebooting, just to test if it was going to change something, but no luck.
The phone reboots, the "Cyanogen" logo starts to glow for 7/8 times and then... bzzzz, short vibration and all over again (i.e. bootloop).
I tried with an older official signed .zip from Cyanogen OS (cm-12.1-YOG4PAS3AJ-ham-signed, instead of newer cm-12.1-YOG4PAS3OH-ham-signed), but even worst, it fails at "verify package" step, aborting procedure.
MD5 signatures triple-checked each time versus source.
I saw some threads where it seems possible to change the bit, on system image, controlling developer option, to manually post-enable unlocking, but it's suitable only for Nexus or OnePlus One. No instructions for ZUK Z1.
Or maybe do I need a "donor" sharing a stock .zip with this option yet enabled?
Bootloop would be still there, but I possibly could enable to "flash", "boot" and "shell" vs the device, giving me much more options to try.
One last doubt anyway. If I press "Volume Down" + "Power" button at boot, I get into a menu like this:
http: // postimg.org/image/s5badiefh/ (remove extra spaces).
Viewing other examples posted on forums, I noted that at least the "Factory reset" is missing.
Could it be an hint for anything useful?
Click to expand...
Click to collapse
For me, this method worked exactly as described, booting into stock rom correctly.
now, if you mentioned it in the picture, there is another option. so, i ve noticed too this menu. There is an app called QPST wich can help you. Follow this thread: http://forum.xda-developers.com/zuk-z1/help/bricked-zuk-z1-t3277257 .
So when you enter in QFIL, connect the phone to computer and boot with volume down+ power into this menu from your picture. The Qfil app should detect some ports. You must choose the 9008 one, from what i have read.
Anyway, for me this method, didn t work because the pc couldn t detect the right port, only the zuk tookit did it for me.
You read the thread i suggested, and try that method, it may work for you.
Extentho said:
For me, this method worked exactly as described, booting into stock rom correctly.
now, if you mentioned it in the picture, there is another option. so, i ve noticed too this menu. There is an app called QPST wich can help you. Follow this thread: http://forum.xda-developers.com/zuk-z1/help/bricked-zuk-z1-t3277257 .
So when you enter in QFIL, connect the phone to computer and boot with volume down+ power into this menu from your picture. The Qfil app should detect some ports. You must choose the 9008 one, from what i have read.
Anyway, for me this method, didn t work because the pc couldn t detect the right port, only the zuk tookit did it for me.
You read the thread i suggested, and try that method, it may work for you.
Click to expand...
Click to collapse
Thanks again Extentho.
I saw QPST trick, but it's not catching right port and/or not getting right permission to stop phone from re-booting.
I think that adb/toolkit method should work also for me. I made attempts with other official ROMs: I noticed that for the older ones, the result is a bit different. They get stuck in a "black screen + notify led lighted in blue" state, rather than bootlooping.
Maybe erasing system partitions is needed, but I'm very reluctant to such dangerous way, without expertised advice.
Weirdest thing is that I did anything to get this situation, I just found my device in this mess.
Of course ZUK official support is well silent at my requests.
dalviking said:
Thanks again Extentho.
I saw QPST trick, but it's not catching right port and/or not getting right permission to stop phone from re-booting.
I think that adb/toolkit method should work also for me. I made attempts with other official ROMs: I noticed that for the older ones, the result is a bit different. They get stuck in a "black screen + notify led lighted in blue" state, rather than bootlooping.
Maybe erasing system partitions is needed, but I'm very reluctant to such dangerous way, without expertised advice.
Weirdest thing is that I did anything to get this situation, I just found my device in this mess.
Of course ZUK official support is well silent at my requests.
Click to expand...
Click to collapse
Try to post some pics about the troubles you encounter. If we receive a solution, this may be helpful for all of us in the future. Now, exactly, what can you acces on phone(recovery, fastboot, )?
Also, check varios threads from other phones with the same problems(one plus one, lg , htc) ,etc. Find a solved situation like yours, and we may adapt that solution to you
Hi guys,
Just to close this topic.
I was finally able to install the ZUI ROM through the QFIL program.
It's a little bit tricky, due to the fact that it is strongly suggested:
- to use a Windows 7 machine started without Signature Enforcement enabled;
- to start QFIL (admin mode) and be prepared with all needed files loaded in its GUI;
- to power off the phone, then, while pressing volume up button, inserting the USB cable, attached (better if) on a 2.0 port to PC;
- to be fast pressing "Download" button on QFIL program.
After that, I unlocked the bootloader and performed a lot of alternative recovery process.
So, I installed on the device:
- ZUI ROM
- Cyanogen OS convert from ZUI ROM
- Cyanogen OS last updated ROM
- CyanogenMod 12.1 last nightly ROM
- CyanogenMod 13.0 last nightly ROM
and the winner is...
...
...
...
... none of the above.
Each time the very same behaviour: bootloop. So, my last conclusion is: hardware failure (I guess wi-fi module).
I give up.
But for anyone searching a safe way to unlock a bootloader without accessing to developer options: the QFIL method works like a charm (once installed properly).
Thanks for support.
Messed my zuk z1
I tried to flash stock room in my zuk z1 , I downloaded Qualcomm file for the ROM and installed the required in my laptop,I wiped all data in my phone using TWRP .though my power button is not working I used tool kit to reboot my phone by connecting into fast boot mode,here comes the prob by mistake I entered the wrong command which locks my bootloader .I don't know what to do...help me.....
I have unlocked the bootloader but I can not figure out how to root this thing at all. Has anyone had any success? I would like TWRP and SuperU.
this device is new yet. give it time
Tmobilefan906 said:
this device is new yet. give it time
Click to expand...
Click to collapse
Yeah I didn't realize how new this was whenever I posted it.
TWRP and root instructions available now in post 1 of
https://forum.xda-developers.com/android/general/huawei-ascend-xt-h1611-t3507933/
dabadguycr said:
I have unlocked the bootloader but I can not figure out how to root this thing at all. Has anyone had any success? I would like TWRP and SuperU.
Click to expand...
Click to collapse
divineBliss said:
TWRP and root instructions available now in post 1 of
https://forum.xda-developers.com/android/general/huawei-ascend-xt-h1611-t3507933/
Click to expand...
Click to collapse
You've already been helping me before you posted this.
People reading this thread might not realize we have root now. It's for their benefit .
dabadguycr said:
You've already been helping me before you posted this.
Click to expand...
Click to collapse
divineBliss said:
People reading this thread might not realize we have root now. It's for their benefit .
Click to expand...
Click to collapse
Good Point, I know my thread shows up first on Bing whenever I search for my phone and rooting help.
I have another XT and followed all instructions fine but no SuperSU when checking the phone. I tried flashing it twice (the one from the OP in main thread) and nothing. Am I missing a step?
I had installed fine on the first phone. this new one is 100% stock, unlocked bootloader, installed TWRP successfully but no supersu and root checker confirms no root.
Is it B140 or what? If you are missing a step, only you can check that.
powerserge1 said:
I have another XT and followed all instructions fine but no SuperSU when checking the phone. I tried flashing it twice (the one from the OP in main thread) and nothing. Am I missing a step?
I had installed fine on the first phone. this new one is 100% stock, unlocked bootloader, installed TWRP successfully but no supersu and root checker confirms no root.
Click to expand...
Click to collapse
divineBliss said:
Is it B140 or what? If you are missing a step, only you can check that.
Click to expand...
Click to collapse
Fixed
Can someone check the EMUI Huawei website for the unlock bootloader? Is it still working for requesting code? It keeps loop me back to the EMUI 5.0 page
sweetboy02125 said:
Can someone check the EMUI Huawei website for the unlock bootloader? Is it still working for requesting code? It keeps loop me back to the EMUI 5.0 page
Click to expand...
Click to collapse
Ya same. I got angry since I spent hours trying to find it so I just paid $4 and had DC-Unlocker unlock my bootloader.
sweetboy02125 said:
Can someone check the EMUI Huawei website for the unlock bootloader? Is it still working for requesting code? It keeps loop me back to the EMUI 5.0 page
Click to expand...
Click to collapse
webosFTW said:
Ya same. I got angry since I spent hours trying to find it so I just paid $4 and had DC-Unlocker unlock my bootloader.
Click to expand...
Click to collapse
If you follow this guide there should be no issue. The rootmygalaxy link should be pretty straightforward at unlocking the bootloader. The guide should be stickied in the OP.
https://forum.xda-developers.com/showpost.php?p=70515102&postcount=649
powerserge1 said:
If you follow this guide there should be no issue. The rootmygalaxy link should be pretty straightforward at unlocking the bootloader. The guide should be stickied in the OP.
https://forum.xda-developers.com/showpost.php?p=70515102&postcount=649
Click to expand...
Click to collapse
The issue is that https://emui.huawei.com/en/plugin.php?id=unlock that page hasnt worked for days. Keep redirecting me to the main page.
webosFTW said:
The issue is that https://emui.huawei.com/en/plugin.php?id=unlock that page hasnt worked for days. Keep redirecting me to the main page.
Click to expand...
Click to collapse
Yes use a different browser. Not working with chrome but working with edge. Go to the same link, it will bring you to EMUI 5.0 page, towards the top click on "download" then on the following page under the search bar click on "unlock bootloader" and it will bring you to the unlocking page. Just confirmed working. Updating the guide and will make a new post for root and twrp
Updated guide: https://forum.xda-developers.com/android/development/huawei-ascend-xt-h1611-feb27-2017-t3564389
Unlocked the boot loader, now adb/fastboot-15 Second won't work
Hello guys!
I used the 15 Second minimal adb/fastboot package from this site to unlock the boot loader. All seemed to go well, a screen message said success or something like that. It's been over 2 weeks since I had to put the phone down and take care of some other business. Now, after turning the phone off and then back on again when I am ready when I type in "fastboot devices" in the elevated cmd window in the adb directory the only message that comes back is "waiting on the device." Or the equivalent. I have tried what I could find from searching with Google to no avail. I am pretty sure that I am using the same cord, laptop, and everything that worked when I unlocked the boot loader. So, I am at a loss.
My goal originally was to use madvane20's slim downed version of b180 just to get it working again as my almost 2 years old P10 was stolen. I have no money in my budget for a new phone until Feb. 2020. I last talked with him in a series of PM's ending around May of last year, when a reply stated he had to get back to work on the last part of it. I have since seen a post referencing that it was ready in a package that after I had successfully unlocked the boot loader, it would root and install everything. This would have made me a happy guy... but I also noticed a custom ROM is now to be had based on Android 7. In order to get my Bank App's updated version of it's Mobile App to work, I have to install Android v 7 or higher. That's the main app that needs v 7 or better that I use daily. Several times...
But, now when I power up the phone, the first message is, "Your device has been unlocked and cannot be trusted... Press the Power Key now to reboot. Or the device will automatically reboot in 5 seconds." Which it does, the first time walking me through the Set-Up process, now it just boots into Huawei's EMUI 4.1. But, I cannot get adb to find the phone to follow the remainder of the instructions in the guide, "AT&T Huawei Ascend XT H1611 Feb27, 2017 update all things Root and TWRP (guide)"
Nor, can I get into the Recovery mode using the Vol Down/Power Keys.
So, where have I gone wrong or what is my next step? Since the phone can not be found and I can not get into Recovery using the proper keys what do I need to do and how do I do it?
I want to:
Root the phone.
Install the custom ROM I mentioned.
Or, Install an upgrade, if possible, to Android v 7... But,
can not get the phone recognized to get into a Recovery mode (is that right?) to push TWRP to it as well as the other files
it needs and to do whatever the Guides tell me to do.
Specs on the phone:
Model: H1611
Build: H1611C07B180
EMUI v: 4.1
Android v: 6.0.1
Security Patch level: September 1, 2017
Baseband v: 20234
Kernal v: 3.10.49-g03b627c
Sorry for the long post, but I thought it might answer some questions that came to mind before replying back.
Thanks in advance. I'm not here often, but when I am I am always relieved to get out of some jam I have gotten myself into!
mike0921
mike0921,
What happens if the phone is in normal mode and you type "adb devices" from the PC adb directory command prompt?
divineBliss said:
mike0921,
What happens if the phone is in normal mode and you type "adb devices" from the PC adb directory command prompt?
Click to expand...
Click to collapse
I just now found a new(er) USB cable for the phone. I also uninstalled the H1611 under Portable Devices in the Device Manager and rebooted the laptop. Where before, under Events the message was ".... needs further installation..." it now showed a successful install.
At the "adb devices" command, nothing happened, no response. I went and found the directions and explanations for the use of the top 30 commands. It told me to reboot the bootloader. A screen on the phone had me confirm the RSA command. Afterwhich the Fastoot&Recovery Mode screen with the little green Android guy with the message Phone Unlocked, FRP Unlock messages.
I went back to the elevated cmd window and at the adb directory command prompt entered "fastboot devices" and Voila! There were some letters and numbers, five or six spaces and the word "fastboot."
So, am I good to go with the rest of the steps in the guide from here? A question, about him saying to flash the Superuser zip file using TWRP. Is that suppose to already be on my SD card to flash it or can I flash it from my laptop without having to touch the phone or current USB cable? It seems stable but I am a bit gunshy and don't have much faith left in the old equipment I am having to use. A very old, refurbished HP Elitebook 8460P which is running really wonky, a not too new USB cable, the last of five I dug up and have used and finally works but is a bit loose, and Windows 10 1903 etc., which has disappeared all kinds of things I am having to run down) Can I use the "push" command to move the zip file to the SD card? And is that a fastboot function or an adb function? I seem to have read somewhere along the way to this point here that "push" is what I want to do, but powerserge1's Step 7 states to flash it using TWRP. I just want to check. And should questions from here on out be placed in his 184-page thread? I still haven't managed to read the whole thing, it seems to go off in so many other directions that I don't think I need to travel down. But, I will follow your advice.
I want to say a hearty thanks for your help. I was stuck, confused and frustrated at getting no results from Googling and reading for hours and getting nowhere it seemed. And I think I am good to go now.
Thoughts? Suggestions?
Just to be clear, The SuperSU zip file is currently on my laptop in the adb directory. Not on the phone.
mike0921 said:
I just now found a new(er) USB cable for the phone. I also uninstalled the H1611 under Portable Devices in the Device Manager and rebooted the laptop. Where before, under Events the message was ".... needs further installation..." it now showed a successful install.
At the "adb devices" command, nothing happened, no response. I went and found the directions and explanations for the use of the top 30 commands. It told me to reboot the bootloader. A screen on the phone had me confirm the RSA command. Afterwhich the Fastoot&Recovery Mode screen with the little green Android guy with the message Phone Unlocked, FRP Unlock messages.
I went back to the elevated cmd window and at the adb directory command prompt entered "fastboot devices" and Voila! There were some letters and numbers, five or six spaces and the word "fastboot."
So, am I good to go with the rest of the steps in the guide from here? A question, about him saying to flash the Superuser zip file using TWRP. Is that suppose to already be on my SD card to flash it or can I flash it from my laptop without having to touch the phone or current USB cable? It seems stable but I am a bit gunshy and don't have much faith left in the old equipment I am having to use. A very old, refurbished HP Elitebook 8460P which is running really wonky, a not too new USB cable, the last of five I dug up and have used and finally works but is a bit loose, and Windows 10 1903 etc., which has disappeared all kinds of things I am having to run down) Can I use the "push" command to move the zip file to the SD card? And is that a fastboot function or an adb function? I seem to have read somewhere along the way to this point here that "push" is what I want to do, but powerserge1's Step 7 states to flash it using TWRP. I just want to check. And should questions from here on out be placed in his 184-page thread? I still haven't managed to read the whole thing, it seems to go off in so many other directions that I don't think I need to travel down. But, I will follow your advice.
I want to say a hearty thanks for your help. I was stuck, confused and frustrated at getting no results from Googling and reading for hours and getting nowhere it seemed. And I think I am good to go now.
Thoughts? Suggestions?
Just to be clear, The SuperSU zip file is currently on my laptop in the adb directory. Not on the phone.
Click to expand...
Click to collapse
And after backing up in TRWP, I just checked the SD card's contents for the backup and saw the SuperSU zip file neatly placed on it as well. Just to be clear!??!
Okay, I somehow screwed this up I think. I was a little distracted by a friend dropping by. After telling her to give me a minute, I looked back at the phone after following Step 6:
Step 6: Confirm phone goes to FASTBOOT & RESCUE mode.
a) fastboot devices (to make sure your device is recognized)
b) fastboot boot TWRP.img (boots TWRP.img from Step 3)
c) The phone will boot into TWRP. Always select Keep Read Only from the first screen every time you go into TWRP.
Peek around a bit if you want to, then use TWRP to backup your stock recovery to external micro SD.
d) Reboot bootloader from inside TWRP to flash this custom recovery image (no adb command this time, you are rebooting to the bootloader from TWRP, you will see this option under "reboot" in TWRP).
e) fastboot flash recovery TWRP.img (now flashes TWRP recovery to the phone)
I then went to Step 7:
Step 7: After phone reboots, get into TWRP recovery repeating Step 6, a and b or hold the power button and volume up button from power-off state, then release when you see Huawei logo.
But now, the phone isn't being recognized again. And when I shut it off, hold Volume Up and Power buttons, I get a screen that asks if I want to: Reboot system now; Wipe data/factory reset; Wipe cache partition. Not the Recovery Screen with the options I got used to seeing in little green characters.
I tried the Reboot system now option and I'm back into the Huawei EMUI with everything appearing unchanged. Powered off, did the Vol Up + Power buttons and am back with the screen offering the three options I mentioned above. And the phone not being recognized after the "Devices" command.
Can you clarify my confusion? What am I doing wrong? Or not doing?
Thanks.
mike
---------- Post added at 06:47 PM ---------- Previous post was at 05:53 PM ----------
mike0921 said:
I just now found a new(er) USB cable for the phone. I also uninstalled the H1611 under Portable Devices in the Device Manager and rebooted the laptop. Where before, under Events the message was ".... needs further installation..." it now showed a successful install.
At the "adb devices" command, nothing happened, no response. I went and found the directions and explanations for the use of the top 30 commands. It told me to reboot the bootloader. A screen on the phone had me confirm the RSA command. Afterwhich the Fastoot&Recovery Mode screen with the little green Android guy with the message Phone Unlocked, FRP Unlock messages.
I went back to the elevated cmd window and at the adb directory command prompt entered "fastboot devices" and Voila! There were some letters and numbers, five or six spaces and the word "fastboot."
So, am I good to go with the rest of the steps in the guide from here? A question, about him saying to flash the Superuser zip file using TWRP. Is that suppose to already be on my SD card to flash it or can I flash it from my laptop without having to touch the phone or current USB cable? It seems stable but I am a bit gunshy and don't have much faith left in the old equipment I am having to use. A very old, refurbished HP Elitebook 8460P which is running really wonky, a not too new USB cable, the last of five I dug up and have used and finally works but is a bit loose, and Windows 10 1903 etc., which has disappeared all kinds of things I am having to run down) Can I use the "push" command to move the zip file to the SD card? And is that a fastboot function or an adb function? I seem to have read somewhere along the way to this point here that "push" is what I want to do, but powerserge1's Step 7 states to flash it using TWRP. I just want to check. And should questions from here on out be placed in his 184-page thread? I still haven't managed to read the whole thing, it seems to go off in so many other directions that I don't think I need to travel down. But, I will follow your advice.
I want to say a hearty thanks for your help. I was stuck, confused and frustrated at getting no results from Googling and reading for hours and getting nowhere it seemed. And I think I am good to go now.
Thoughts? Suggestions?
Just to be clear, The SuperSU zip file is currently on my laptop in the adb directory. Not on the phone.
Click to expand...
Click to collapse
And after backing up in TRWP, I just checked the SD card's contents for the backup and saw the SuperSU zip file neatly placed on it as well. Just to be clear!??!
Okay, I somehow screwed this up I think. I was a little distracted by a friend dropping by. After telling her to give me a minute, I looked back at the phone after following Step 6:
Step 6: Confirm phone goes to FASTBOOT & RESCUE mode.
a) fastboot devices (to make sure your device is recognized)
b) fastboot boot TWRP.img (boots TWRP.img from Step 3)
c) The phone will boot into TWRP. Always select Keep Read Only from the first screen every time you go into TWRP.
Peek around a bit if you want to, then use TWRP to backup your stock recovery to external micro SD.
d) Reboot bootloader from inside TWRP to flash this custom recovery image (no adb command this time, you are rebooting to the bootloader from TWRP, you will see this option under "reboot" in TWRP).
e) fastboot flash recovery TWRP.img (now flashes TWRP recovery to the phone)
I then went to Step 7:
Step 7: After phone reboots, get into TWRP recovery repeating Step 6, a and b or hold the power button and volume up button from power-off state, then release when you see Huawei logo.
But now, the phone isn't being recognized again. And when I shut it off, hold Volume Up and Power buttons, I get a screen that asks if I want to: Reboot system now; Wipe data/factory reset; Wipe cache partition. Not the Recovery Screen with the options I got used to seeing in little green characters.
I tried the Reboot system now option and I'm back into the Huawei EMUI with everything appearing unchanged. Powered off, did the Vol Up + Power buttons and am back with the screen offering the three options I mentioned above. And the phone not being recognized after the "Devices" command.
Can you clarify my confusion? What am I doing wrong? Or not doing?
Thanks.
mike
Sorry for the delay. What's the latest status with attempts to root the phone?
I'll be making a video for this with the 7 inch tablet on Nov. 29th or 30th (depending on the time I have)
General Disclaimer: I'm not responsible if you brick your tablet. This is how I did it personally as other methods here didn't work for me. I have yet to test this method on a 7 inch, also do not have access to the Surf variants. This has only been tested on the 10.1 inch with the keyboard. Will update when I test with the 7 inch.
What's Needed:
MTK Fastboot Drivers: https://online.mediatek.com/Public Documents/MTK_Android_USB_Driver.zip
Magisk Manager Canary: https://forum.xda-developers.com/apps/magisk/dev-magisk-canary-channel-bleeding-edge-t3839337
Stock Boot Image: https://forum.xda-developers.com/wa...eral/stock-stock-backups-images-otas-t3998227
ADB and Fastboot: https://www.xda-developers.com/what-is-adb/
Prerequisites:
Personally, I had issues getting my PC to recognize the tablets in Fastboot mode. The drivers wouldn't install. This might be optional for some of you, but I thought I'd include it just in case.
Installing MTK Fastboot Drivers from the link above
If you plugin your device in fastboot mode and your PC doesn't recognize it, follow these steps. If it did, skip this part.
1.) Download the drivers above and unzip the Zip file somewhere on your PC (desktop or My Documents is easiest)
2.) Boot your Tablet into Fastboot Mode by holding Vol + and Power, then select Fastboot from the Menu
*NOTE* There is a bug with these tablet's that the volume buttons are mislabeled. Really dumb, but I guess that's why they were 55 bucks for the 10 inch on black friday
3.) Plug the device into your PC and open Device Manager by pressing WinKey+R and typing devmgmt.msc, hit Enter
4.) If there's an Other Device listed called Android, follow these steps. If it isn't there, follow the next set of steps
5.) Open a Command Prompt window as Admin and type the following command
Code:
bcdedit.exe /set nointegritychecks on
6.) Hit enter, then restart your PC
7.) Once the PC is restarted, make sure your tablet is connected in Fastboot mode and open Device Manager again
8.) Right click Android under Other Devices and select Update Drivers
9.) Click the Browse my Computer for driver software button and select the MTK Folder you extracted from the download link above
10.) From there, you can open command prompt, type fastboot devices and see if your tablet shows up and move on to root!
Unlocking your Bootloader
From here, you can unlock your bootloader very easily to Root your device
This will wipe all data off the tablet!
0.) Enable OEM Unlock and USB Debugging on the tablet by going to Settings->About and tap Build Number 7 times. From here, enter the new Developer Options that unlock and turn on OEM Unlock and USB Debugging.
1.) Boot your tablet into Fastboot mode and connect it to your PC
2.) Open a Command Prompt window and type the following command, then hit enter
Code:
fastboot flashing unlock
3.) Follow the instructions on screen to unlock your bootloader
4.) Now Boot your device and we'll move on to making a rooted Boot Image
Creating a Rooted Boot Image with Magisk Manager
0.) Make sure you already have Wifi setup and connected before the first time you open Magisk Manager on your device! Make sure it auto connects as well
1.) Download Magisk Manager Canary from the link above
2.) Install it to your device
3.) Download boot Image from the Stock Boot Image part of the Prerequisites above and put the boot.img on your devices internal memory
4.) Open Magisk Manager and select Install Magisk
5.) Select Patch File and select the boot.img from your internal storage
6.) Once its done patching the image, take magisk_patched.img from the downloads folder of your device and move it onto your PC
7.) Boot your tablet into Fastboot mode and plug it into your PC
8.) Open Command Prompt and type the following command and hit enter (make sure you know your magisk_patched.img file location)
Code:
fastboot flash boot magisk_patched.img
9.) Reboot the device and you'll be Rooted!
Optional Steps like Modules and Debloating
My basic debloat script: https://forum.xda-developers.com/wa...s-general/root-walmart-bloat-remover-t4011639
Will be testing GSI roms on the spare 7 inch and will list those here
Recommended Magisk Modules:
Viper4Android Legacy
FDE.AI
MagiskHide Props Config
Systemless Hosts
Youtube Vanced Black
Magisk Setting to Enable:
Magisk Hide
Rename Magisk Manager App (keeps app from detecting magisk root)
Credits:
Myself for this root method @byproxy for reminding me to add the steps for OEM Unlock and enabling wifi before opening Magisk Manager for the first time
I'll start this off saying i'm an amateur at this, but I cannot for the life of me get an option to show up in magisk to patch the boot image even though it's on my 7" tablet. Any thoughts?
The bootloader was unlocked and it was successful so that's not the issue.
Are you online? I had the same problem.
Xavster2 said:
I'll start this off saying i'm an amateur at this, but I cannot for the life of me get an option to show up in magisk to patch the boot image even though it's on my 7" tablet. Any thoughts?
The bootloader was unlocked and it was successful so that's not the issue.
Click to expand...
Click to collapse
Xavster2 said:
I'll start this off saying i'm an amateur at this, but I cannot for the life of me get an option to show up in magisk to patch the boot image even though it's on my 7" tablet. Any thoughts?
The bootloader was unlocked and it was successful so that's not the issue.
Click to expand...
Click to collapse
Sorry, been a busy few days, but make sure you're connected to Wifi, close Magisk Manager, then reopen it and you'll be good to go!
Onn 8" walmart tablet
I purchased the 8" Onn walmart tablet second hand from a store called dirt cheap. Box didnt look to be opened but it had been. The tablet had been setup with someones gmail account that i do not know. The tablet was for a 4yo girl to use to learn preschool. Is there just any simple way to remove this google FRP lock ? I dont care if i lose the info on it as its not mine. I just want her to be able to use the tablet. Any help would be much appreciated please
CoachDad said:
I purchased the 8" Onn walmart tablet second hand from a store called dirt cheap. Box didnt look to be opened but it had been. The tablet had been setup with someones gmail account that i do not know. The tablet was for a 4yo girl to use to learn preschool. Is there just any simple way to remove this google FRP lock ? I dont care if i lose the info on it as its not mine. I just want her to be able to use the tablet. Any help would be much appreciated please
Click to expand...
Click to collapse
Forced factory reset should do it. There is small pin hole near the power button. I believe pressing this hidden button(with a Sim card ejector, or paper clip).
If pressing does not do anything. Maybe press the button then hold power button too
mrmazak said:
Forced factory reset should do it. There is small pin hole near the power button. I believe pressing this hidden button(with a Sim card ejector, or paper clip).
If pressing does not do anything. Maybe press the button then hold power button too
Click to expand...
Click to collapse
Thank you for responding so fast. I've boot into recovery mode /wiped everything...its back to factory. The pinhole reset button does nothing other than reboot it . Ive tried all combos to with the reset button but nothing. Also i've read that its possible to use odin? if i can get it into download mode.
Ive downloaded the stock rom posted on an sdcard wondering if i can possibly update in recovery mode? Im sorta a newb at this stuff. I've been reading for 4 days on this matter. I've practiced a root on an old tablet with success. I guess at this point unless i can sell it as is giving the customer that it has this frp lock on it. If the know how to fix it so be it. Im not sure there is a working solution for frp bypass on these tablets.
CoachDad said:
Thank you for responding so fast. I've boot into recovery mode /wiped everything...its back to factory. The pinhole reset button does nothing other than reboot it . Ive tried all combos to with the reset button but nothing. Also i've read that its possible to use odin? if i can get it into download mode.
Ive downloaded the stock rom posted on an sdcard wondering if i can possibly update in recovery mode? Im sorta a newb at this stuff. I've been reading for 4 days on this matter. I've practiced a root on an old tablet with success. I guess at this point unless i can sell it as is giving the customer that it has this frp lock on it. If the know how to fix it so be it. Im not sure there is a working solution for frp bypass on these tablets.
Click to expand...
Click to collapse
This is an mtk device not Samsung. So there is no Odin or download mode. There is spflash tool, and preloader.
And if you flash firmware (with default frp partition) then frp lock is cleared.
But you will have to find that file. It maybe in the stock firmwares that are shared, I do not know.
EDIT:
i was having issues but figure it out. maybe it should be so common knowledge that it shouldn't need to be included as a step, but since i don't do this THAT often i didn't think about it and it took me a bit to figure out why i was having issues.
once you get your computer to recognize your device (mine did without needing to mess with any drivers) you need to first make sure to got into the tablet settings -> about and then tap on the build number 7 times to access developer options. then you need to go into developer options and turn on OEM Unlocking & USB Debugging.
THEN follow the guide to unlock bootloader.
then (since the tablet is factory reset once you unlock) do the above AGAIN to turn USB Debugging back on after you reboot.
also note that you need to have an internet connection on the tablet to utilize magisk. once you got all that square, then continue on with steps for full root.
hope that helps!
byproxy said:
EDIT:
i was having issues but figure it out. maybe it should be so common knowledge that it shouldn't need to be included as a step, but since i don't do this THAT often i didn't think about it and it took me a bit to figure out why i was having issues.
once you get your computer to recognize your device (mine did without needing to mess with any drivers) you need to first make sure to got into the tablet settings -> about and then tap on the build number 7 times to access developer options. then you need to go into developer options and turn on OEM Unlocking & USB Debugging.
THEN follow the guide to unlock bootloader.
then (since the tablet is factory reset once you unlock) do the above AGAIN to turn USB Debugging back on after you reboot.
also note that you need to have an internet connection on the tablet to utilize magisk. once you got all that square, then continue on with steps for full root.
hope that helps!
Click to expand...
Click to collapse
I did not realize I didn't include that step. Total noob mistake when typing a tutorial up for android. I do this almost daily at work, so I forget to include it
CoachDad said:
Thank you for responding so fast. I've boot into recovery mode /wiped everything...its back to factory. The pinhole reset button does nothing other than reboot it . Ive tried all combos to with the reset button but nothing. Also i've read that its possible to use odin? if i can get it into download mode.
Ive downloaded the stock rom posted on an sdcard wondering if i can possibly update in recovery mode? Im sorta a newb at this stuff. I've been reading for 4 days on this matter. I've practiced a root on an old tablet with success. I guess at this point unless i can sell it as is giving the customer that it has this frp lock on it. If the know how to fix it so be it. Im not sure there is a working solution for frp bypass on these tablets.
Click to expand...
Click to collapse
I was able to remove FRP lock on one of mine by flashing the stock rom with SP Flash Tool. I used the full wipe and download selection with every partition selected including boot.
no worries! i didn't think about it either until i was having issues. thanks for the tutorial... it was super helpful!! btw it definitely works on the 8" tablet.
Hello! I'm new to all of this, but what I'm trying to accomplish is removing the Google account from this tablet and putting a new image on the ONA19TB002, ONA19TB003, ONA19TB007, Surf 7 and 10 tablets. I followed all of the steps as far as installing the drivers. I had to go through hoops to get the MediaTek Drivers installed, but I have a "warning" cone by it. I haven't been able to find any resolution to this. Any help would be appreciated. I' have a Windows 10 64-bit system that I'm using and the tablet I'm specifically working on at the moment is the ONN ONA19TB003 tablet. The tablet is not being recognized by my laptop when I run the 'fastboot devices' command in PowerShell. Is there something that I'm missing? Any help would be appreciated.
'Quis said:
Hello! I'm new to all of this, but what I'm trying to accomplish is removing the Google account from this tablet and putting a new image on the ONA19TB002, ONA19TB003, ONA19TB007, Surf 7 and 10 tablets. I followed all of the steps as far as installing the drivers. I had to go through hoops to get the MediaTek Drivers installed, but I have a "warning" cone by it. I haven't been able to find any resolution to this. Any help would be appreciated. I' have a Windows 10 64-bit system that I'm using and the tablet I'm specifically working on at the moment is the ONN ONA19TB003 tablet. The tablet is not being recognized by my laptop when I run the 'fastboot devices' command in PowerShell. Is there something that I'm missing? Any help would be appreciated.
Click to expand...
Click to collapse
Personally, I avoid PowerShell at all costs. This kinda stuff has always just seemed to work better with CMD.exe instead of Powershell.
These tablets are kind of a nightmare for this. If you've done the mediatek drivers and still have the warning cone icon, I'm not sure what's next as I haven't hit that wall myself. All I can maybe recommend is right click delete drivers in Device Manager, then start over with the driver install
Removing the Google Account would be needing a FRP Bypass. Someone above stated "I was able to remove FRP lock on one of mine by flashing the stock rom with SP Flash Tool. I used the full wipe and download selection with every partition selected including boot. " so if you can get it recognized, try that
KaptinBoxxi said:
Personally, I avoid PowerShell at all costs. This kinda stuff has always just seemed to work better with CMD.exe instead of Powershell.
These tablets are kind of a nightmare for this. If you've done the mediatek drivers and still have the warning cone icon, I'm not sure what's next as I haven't hit that wall myself. All I can maybe recommend is right click delete drivers in Device Manager, then start over with the driver install
Removing the Google Account would be needing a FRP Bypass. Someone above stated "I was able to remove FRP lock on one of mine by flashing the stock rom with SP Flash Tool. I used the full wipe and download selection with every partition selected including boot. " so if you can get it recognized, try that
Click to expand...
Click to collapse
Ok, thank you! This is a shot in the dark, but in order for ADB to work, USB debugging has to be enabled. I can't do that as the tablet is locked by FRP and I have looked countless times on Google and MSN to see if it's possible. Do you have any tips for that?
I don't know what I'm doing wrong, but for some reason I can't seem to get. The tablet to stay in fastboot mode. It just says waiting for device.
will this root onn 8 inch tablet running android 9
soateufel said:
I don't know what I'm doing wrong, but for some reason I can't seem to get. The tablet to stay in fastboot mode. It just says waiting for device.
Click to expand...
Click to collapse
Sorry for late reply. Been away from home with work. When fastboot mode indicates "waiting for device," it generally means that your device is not properly communicating with your PC or laptop. This is nearly always due to missing or incorrect drivers 9n your computer. There are several comprehensive guides here on XDA for installing necessary ADB & Fastboot drivers.
installed magisk manager on onn 8 and also have img zip but win i go to patch it magisk manager crashes
when you mean patch boot img do mean to unzip file on onn 8
Hello,
I'll try to be as specific as I can with my steps, so sorry If you don't like the format (or if its not even allowed), it's the best way I can explain step by step everything I did.
so... what do I want to do? Simply install some custom ROM to my SM-G570M so I can get rid of all the bloatware.
What's stopping me from doing it like I did it before? well...
>I flashed last version of TWRP via Odin
>Download mode (V- + Power + Home), Odin, the flash itself, everything went well, at least it appeared so
>When trying to load into it (V+ + Power + Home), I get a blue screen with android's logo and the words "Instaling system update"
>Immediately after I get another screen, this time android's logo is laying down, with a yellow ! above and the words "No command"
>Waiting a few seconds will get me to Android Recovery (the clasic move with Volume select with Power menu) with this in it:
#fail to open recovery_cause(No such file or directory)#
#Reboot recovery cause is [UNKNOWN]#
No support SINGLE-SKU
Click to expand...
Click to collapse
>I don't really know what to do, TWRP is nowhere to be seen
>I factory reset my phone (I don't really know why)
this is when things get interesting (that is, frustrating af)
>Phone boots fine, but OEM Unlock is not available. Not even greyed out, not even locked. It's not there at all
>I Google about it and try about... 50 different "solutions"
>Change system date to 7+ days to the past and trigger a false Update lookout, restart... nothing
>Triggered Update lookouts twice to make the sure the phone "knows" I searched for it 10 days ago and today... nothing
>I Literally write the steps down and start superpermutating that **** for around two hours... nothing
>Some other random non-Samsung, non-my-phone-specific "solutions"... nothing
>I come across adb (never used it before, never had to)
>It claimed I could do the OEM Unlock from Windows cmd
>I download adb 15 seconds installer, adb and fastboot drivers (both), I already had Samsung specific USB drivers, everything I need
>open CMD and do adb devices
>see my device there, nice
>adb reboot bootloader
>it boots there, n i c e
>fastboot devices
>... nothing
>fastboot device, maybe it was without the s
>stuck in waiting for device
>close everything, start again
>this time I do directly fastboot OEM unlock
>waiting for device
here I'll explain what I saw in Device Manager in all my adb odyssey:
Drivers are recognized in its normal state (that is, phone connected, no dev ****, just using it) with its full name (Samsung J5 Prime bla bla bla). Besides that I have some Samsung USB Drivers showing as modems? idk why. Once I change my phone state (let's say, I do adb reboot bootloader) drivers completely dissapear. Not even showing as *Unrecognized !*, no "Android Device 1.0". It's not there at all. Only thing I see is is the usb modems? drivers.
And yes, I used every USB Port I have, the only thing it changes is a #n besides the modem drivers.
I did read you have to install drivers twice? Once in each state? I did so and nothing.
I did "Added Legacy Hardware", where I saw different ones: ADB Interface, Samsung ADB Interface, Bootloader Interface, etc. Added every single one of them, updated them (I even got the Google USB thing, it did nothing) Sometimes it would bring some error (Can't do that right now or something like that), sometimes "It's already the best we have", but still not regognizing it in cmd fastboot devices.
I also superpermutated every step I could, even doing things completely illogical. I didn't care, I stayed awake until 9AM doing it... and nothing
I did noticed, at around 5am, half asleep, that my "bootloader" window (in my phone) was... not... really... a bootloader? whenever I would adb reboot bootloader it would get me to the same Download Mode I would get by pressing V- + Power + Home. I dismissed it, not only it was really late, It could have just been a normal misunderstanding... you know, language barriers and such (I'm not english native, so I'm constantly reading things in practically two languages, maybe *Bootloader* and the *DW Mode* where actually the same and people are arbitrarily obtuse, I thought) but it still bothers me nonetheless.
I also tried, since, you know, all I want is a custom ROM, to play with Recovery Mode adb sideload? But I would always get some error 21 and other I didn't really catch.
That's my problem(s). I don't really know what to do, and I don't want to wait seven days (or more, because I read some people waiting for weeks) to have the actual OEM Unlock option in my Dev Options.
Can I get a hand with this? Is my bootloader even active? Can I even do OEM unlock in my current state? did I miss a driver, among the 100+ I downloaded even from dubious webs? Never worked with phones before so I'm practically new on this, last time I touched android I did perfectly flash TWRP through Odin and did everything from there.
please
pretty please
Nezvanova said:
Hello,
I'll try to be as specific as I can with my steps, so sorry If you don't like the format (or if its not even allowed), it's the best way I can explain step by step everything I did.
so... what do I want to do? Simply install some custom ROM to my SM-G570M so I can get rid of all the bloatware.
What's stopping me from doing it like I did it before? well...
>I flashed last version of TWRP via Odin
>Download mode (V- + Power + Home), Odin, the flash itself, everything went well, at least it appeared so
>When trying to load into it (V+ + Power + Home), I get a blue screen with android's logo and the words "Instaling system update"
>Immediately after I get another screen, this time android's logo is laying down, with a yellow ! above and the words "No command"
>Waiting a few seconds will get me to Android Recovery (the clasic move with Volume select with Power menu) with this in it:
>I don't really know what to do, TWRP is nowhere to be seen
>I factory reset my phone (I don't really know why)
this is when things get interesting (that is, frustrating af)
>Phone boots fine, but OEM Unlock is not available. Not even greyed out, not even locked. It's not there at all
>I Google about it and try about... 50 different "solutions"
>Change system date to 7+ days to the past and trigger a false Update lookout, restart... nothing
>Triggered Update lookouts twice to make the sure the phone "knows" I searched for it 10 days ago and today... nothing
>I Literally write the steps down and start superpermutating that **** for around two hours... nothing
>Some other random non-Samsung, non-my-phone-specific "solutions"... nothing
>I come across adb (never used it before, never had to)
>It claimed I could do the OEM Unlock from Windows cmd
>I download adb 15 seconds installer, adb and fastboot drivers (both), I already had Samsung specific USB drivers, everything I need
>open CMD and do adb devices
>see my device there, nice
>adb reboot bootloader
>it boots there, n i c e
>fastboot devices
>... nothing
>fastboot device, maybe it was without the s
>stuck in waiting for device
>close everything, start again
>this time I do directly fastboot OEM unlock
>waiting for device
here I'll explain what I saw in Device Manager in all my adb odyssey:
Drivers are recognized in its normal state (that is, phone connected, no dev ****, just using it) with its full name (Samsung J5 Prime bla bla bla). Besides that I have some Samsung USB Drivers showing as modems? idk why. Once I change my phone state (let's say, I do adb reboot bootloader) drivers completely dissapear. Not even showing as *Unrecognized !*, no "Android Device 1.0". It's not there at all. Only thing I see is is the usb modems? drivers.
And yes, I used every USB Port I have, the only thing it changes is a #n besides the modem drivers.
I did read you have to install drivers twice? Once in each state? I did so and nothing.
I did "Added Legacy Hardware", where I saw different ones: ADB Interface, Samsung ADB Interface, Bootloader Interface, etc. Added every single one of them, updated them (I even got the Google USB thing, it did nothing) Sometimes it would bring some error (Can't do that right now or something like that), sometimes "It's already the best we have", but still not regognizing it in cmd fastboot devices.
I also superpermutated every step I could, even doing things completely illogical. I didn't care, I stayed awake until 9AM doing it... and nothing
I did noticed, at around 5am, half asleep, that my "bootloader" window (in my phone) was... not... really... a bootloader? whenever I would adb reboot bootloader it would get me to the same Download Mode I would get by pressing V- + Power + Home. I dismissed it, not only it was really late, It could have just been a normal misunderstanding... you know, language barriers and such (I'm not english native, so I'm constantly reading things in practically two languages, maybe *Bootloader* and the *DW Mode* where actually the same and people are arbitrarily obtuse, I thought) but it still bothers me nonetheless.
I also tried, since, you know, all I want is a custom ROM, to play with Recovery Mode adb sideload? But I would always get some error 21 and other I didn't really catch.
That's my problem(s). I don't really know what to do, and I don't want to wait seven days (or more, because I read some people waiting for weeks) to have the actual OEM Unlock option in my Dev Options.
Can I get a hand with this? Is my bootloader even active? Can I even do OEM unlock in my current state? did I miss a driver, among the 100+ I downloaded even from dubious webs? Never worked with phones before so I'm practically new on this, last time I touched android I did perfectly flash TWRP through Odin and did everything from there.
please
pretty please
Click to expand...
Click to collapse
Too much long bro
Let me know if you untick the autorestart at odin when you wanna install twrp
Or seen:just enable OEM and usbdebug at dev option
Make sure that download right and latests version of twrp for your phone(so important)
And install that via odin and untick the autoreboot at odin( bc if you don't that android will uninstall it)
When you see the done message on odin unplug your phone and turn it off and after that try to go recovery mode by V+home and power
Hope that works
amirizad_7436 said:
Too much long bro
Let me know if you untick the autorestart at odin when you wanna install twrp
Or seen:just enable OEM and usbdebug at dev option
Make sure that download right and latests version of twrp for your phone(so important)
And install that via odin and untick the autoreboot at odin( bc if you don't that android will uninstall it)
When you see the done message on odin unplug your phone and turn it off and after that try to go recovery mode by V+home and power
Hope that works
Click to expand...
Click to collapse
I made it long so I don't have to reply a hundred times to things I already did.
Yes, I did untick autorestart. No, I can't enable OEM Unlock (that's the problem I'm having), and usbdebug es required to use adb, so yes, I do have that enabled.
Can't do Odin, it always fails.
Nezvanova said:
I made it long so I don't have to reply a hundred times to things I already did.
Yes, I did untick autorestart. No, I can't enable OEM Unlock (that's the problem I'm having), and usbdebug es required to use adb, so yes, I do have that enabled.
Can't do Odin, it always fails.
Click to expand...
Click to collapse
Well
Try to reset factory and use you phone for a week or a month!i don't know any way
If you find one i would be happy to know
I have exactly same problem!
Hello! Maybe its too long ago but did you manage to solve it??
same problem U9 no OEM unlock option :/