Steps:
Prepare and Notice
A. Warning! Flash phone might get it bricked. I am not responsible for it.
B. Phone is already Oreo firmware, only tested same brand update and downgrade.
C. Backup data, it might be restore factory default setting especially using downgrade ROM version.
D. Unlock bootloader before flash steps.
E. After update successfully, device might be locked again.
F. HWOTA8 Package (HWOTA8_2017110501.zip)
Flash Update
A. Use Vol-Dn + USB Cable to boot into fastboot mode.
B. Use Replace_Recovery.bat in HWOTA8 to flash TWRP recovery.
C. Disconnect USB cable, use Vol-Up + Power to boot into TWRP.
D. Create "HWOTA8" directory in MTP sdcard.
E. Put hwota8_update.zip, MHA_RECOVERY8_NoCheck.img, and three huawei update package (update.zip, update_data_public.zip, and update_all_hw.zip) files into "HWOTA8" directory.
F. TWRP install sdcard hwota8_update.zip, it will reboot and install update automatically.
Downgrade Nougat
A. Put update.zip, update_data_public.zip, and update_all_hw.zip files into HWOTA8 repack directory.
B. Run repack.bat to update zip files.
C. Go through "Flash Update" steps and use repacked zip files.
D. Enter recovery and do factory reset.
Rebrand
A. Put Put hwota8_rebrand.zip and "OEMINFO.bin" (From HWOTA) into SDCard HWOTA8 directory.
B. Use Replace_Recovery.bat in HWOTA8 to flash TWRP recovery.
C. Disconnect USB cable, use Vol-Up + Power to boot into TWRP.
D. Install hwota8_rebrand.zip, it reboots and factory reset failure.
E. Enter fastboot mode and unlock device again.
F. Use Replace_Recovery.bat in HWOTA8 to flash TWRP recovery and enter it.
G. Do "Downgrade Nougat" steps to the rebrand firmware, it fails and reboot but fine.
H. When going to system press "Vol-Up" to enter eRecovery, do "Low-level format data partition".
I. Wait all done and recovery menu show up, reboot and do "Downgrade Nougat" again.
J. Update should be successful this time, rebrand done.
Just one question my friend. This is only for update Oreo to Oreo right? Not for downgrade?
albertobom said:
Just one question my friend. This is only for update Oreo to Oreo right? Not for downgrade?
Click to expand...
Click to collapse
You should be able to install ROLLBACK with it.
I'm going to test later today.
Ok, this is update oreo for oreo?
aureliomilitao said:
Ok, this is update oreo for oreo?
Click to expand...
Click to collapse
Yes I belive and rollback as well.
albertobom said:
Just one question my friend. This is only for update Oreo to Oreo right? Not for downgrade?
Click to expand...
Click to collapse
ante0 said:
You should be able to install ROLLBACK with it.
I'm going to test later today.
Click to expand...
Click to collapse
Rollback installed now.
You have to modify script a little though, as rollback has no public zip.
So simply remove the line that says
echo --update_package=/sdcard/HWOTA8/update_data_public.zip > /cache/recovery/command
in hwota8_update.zip's update-binary.
You should even be able to install something that's not a ROLLBACK, as long as you factory reset after.
The rollback factory resets automatically.
ante0 said:
Rollback installed now.
You have to modify script a little though, as rollback has no public zip.
So simply remove the line that says
echo --update_package=/sdcard/HWOTA8/update_data_public.zip > /cache/recovery/command
in hwota8_update.zip's update-binary.
You should even be able to install something that's not a ROLLBACK, as long as you factory reset after.
The rollback factory resets automatically.
Click to expand...
Click to collapse
Amazing. Thanks my friend.
albertobom said:
Amazing. Thanks my friend.
Click to expand...
Click to collapse
Going Oreo directly to C432B197 does not work, fails at 6% in recovery.
But good that rollback installs.
ante0 said:
Going Oreo directly to C432B197 does not work, fails at 6% in recovery.
But good that rollback installs.
Click to expand...
Click to collapse
Thanks for the info my friend that works for me. :good:
---------- Post added at 05:43 PM ---------- Previous post was at 05:42 PM ----------
ante0 said:
Going Oreo directly to C432B197 does not work, fails at 6% in recovery.
But good that rollback installs.
Click to expand...
Click to collapse
BTW you change script back before test it right?
albertobom said:
Thanks for the info my friend that works for me. :good:
---------- Post added at 05:43 PM ---------- Previous post was at 05:42 PM ----------
BTW you change script back before test it right?
Click to expand...
Click to collapse
Of course xD
I did forget first though, and it failed because it couldn't find files...
Rollback installs fine with SuperSU and Adaway (modifies /system) installed.
ante0 said:
Of course xD
I did forget first though, and it failed because it couldn't find files...
Rollback installs fine with SuperSU and Adaway (modifies /system) installed.
Click to expand...
Click to collapse
OK then. This means I can stay beta and update whenever I want
---------- Post added at 06:08 PM ---------- Previous post was at 06:06 PM ----------
@mankindtw my friends you're the best.
it worked, I used the rom on the 13th and it appeared in the FF a rom on the 27th, I downloaded the files and I did this procedure and now whenever new roms appear, just follow here
Is there a way to root Mate 9 with Oreo and which is the best method?
It works on MHAL29C567B190 EMUI 5.1?
Can I do this procedure to update ?
ante0 said:
Going Oreo directly to C432B197 does not work, fails at 6% in recovery.
But good that rollback installs.
Click to expand...
Click to collapse
Add "Downgrade Nougat" and new HWOTA8 package.
Curiousrge said:
It works on MHAL29C567B190 EMUI 5.1?
Can I do this procedure to update ?
Click to expand...
Click to collapse
No, you should use below HWOTA, not HWOTA8
https://forum.xda-developers.com/mate-9/how-to/guide-mate-9-flash-update-package-t3593108
mankindtw said:
Add "Downgrade Nougat" and new HWOTA8 package.
Click to expand...
Click to collapse
Did I just say how much I love you?
albertobom said:
Did I just say how much I love you?
Click to expand...
Click to collapse
I guess, you might love me even more now.
Have fun playing with it.
mankindtw said:
I guess, you might love me even more now.
Have fun playing with it.
Click to expand...
Click to collapse
You're the man.
Is there a way to disable vibration of the floating navigation dock when long pressed on oreo it is really annoying?
Related
http://consumer.huawei.com/my/support/downloads/detail/index.htm?id=75624
Huawei in the international edition of the official subcontract, tested MT7-L09, MT7-L10
B513 or B511 SD card falls back to 100% B500 version,
SD card upgrade any version 5.1.1 to fall back to 5.1
How to use this downgrade pack
1) Download this downgrade pack and made sure you have a usable micro sd card.
2) After the download is complete, kindly extract the file and copy the file "UPDATE.APP" into the micro sd card and placed it into a new folder named "dload" at the top level of the micro sd card
NOTE: Before proceed with the downgrade process, please ensure that you have perform any necessary backup in order to avoid any data loss.
3) Once you are ready to downgrade, launch the dialer and key in *#*#2846579#*#* and select option "4. Software Upgrade" > "SDCard Upgrade". You will then be prompted a message box, kindly check on "OK" to proceed with downgrade.
4) This downgrade will take about 5-10minutes, at the end you may even see a Warning Notifcation indicating "Software Upgrade Failed", but that's totally fine, You can now reboot the phone by following the on screen instructions.
5) Congratulations ! You are now free to install any available stable Lollipop version by accessing to http://consumer.huawei.com/my/support/index.htm
Thanks download and upload to mega and Put to my topic.
Send frome globe
Hi,
I simply cant reach step 4. When I try to launch the UPDATE.APK, my mobile restart to TWRP and nothing happen. I guess it is because the TWRP is here? Is there a way to unistall it? Or Is there an other way to launch that UPDATE.APK?
Thx a lot for any help.
I guess I need to flash stock recovery? Anyone has stock recovery download link, which can be used for B511?
Yeeeeah... The ultimate, simple and easy to follow guide! Just 2 files to mess with and you are good to go. Worked great on the first try. For the others, you have to be using stock recovery and it is preferred not to be rooted.
Thanks!
Someone has tested for TL10? It works?
Sent from my JAZZ using XDA Free mobile app
just tried it. worked a treat. thanks
Zolocofxp said:
Yeeeeah... The ultimate, simple and easy to follow guide! Just 2 files to mess with and you are good to go. Worked great on the first try. For the others, you have to be using stock recovery and it is preferred not to be rooted.
Thanks!
Click to expand...
Click to collapse
So after using the trasition package and restart you eill still in marshmallow ? Or cb500 ?
---------- Post added at 10:20 AM ---------- Previous post was at 09:26 AM ----------
windfield said:
I guess I need to flash stock recovery? Anyone has stock recovery download link, which can be used for B511?
Click to expand...
Click to collapse
I have a tool that is awesome if you still dont have stock recovery for lollipop then replay to me and i will send you the file by miga !!
Noomy said:
So after using the trasition package and restart you eill still in marshmallow ? Or cb500 ?
---------- Post added at 10:20 AM ---------- Previous post was at 09:26 AM ----------
Click to expand...
Click to collapse
Correct, you will still be on MM.
Thanks man ..
Thanks, tested on MT7-TL10, the best way for to return on Lollipop after MM
Could you please tell me how to get from B500 (downgraded with your tutorial) to B522?
Thank you very much!
I'm still downgrade my phone but i'm block after step 4. I have alaway MM.
I need download a Lolipop rom and retry step 3 ?
KoganFR said:
I'm still downgrade my phone but i'm block after step 4. I have alaway MM.
I need download a Lolipop rom and retry step 3 ?
Click to expand...
Click to collapse
If you are in b500 indeed you are ready to downgrade with a lollipop stock rom. Use the same steps but with the LL rom
meric54 said:
If you are in b500 indeed you are ready to downgrade with a lollipop stock rom. Use the same steps but with the LL rom
Click to expand...
Click to collapse
I'm on B500 too, but I'm unable to downgrade or even upgrade to other version. Maybe I don't have right version, so could you please tell me which version to use? When I tried to downgrade to B329 (official from Huawei site), updater goes to 5%, than I get error: "Software install failed!".
Please, help me out and thanks!
Try b331
Send from hell ✌
Or B326.
Sent from my HUAWEI MT7-L09 using Tapatalk
chudy_85 said:
Try b331
Send from hell
Click to expand...
Click to collapse
Pablo87 said:
Or B326.
Sent from my HUAWEI MT7-L09 using Tapatalk
Click to expand...
Click to collapse
With both of this ROMs I get EMUI logo with 3 options too choose:
- Reboot system now
- Wipe data/factory reset
- Wipe cache partition
Any hint?
Thanks!
Push 3 bottom and when you see huawei logo release power and hold 10 sec volume
Send from hell ✌
Please help me, my Mate 7 MT7-L09 says "Installing update... 5%".
Since lollipop there is no manual update option in huawei updater and even the huawei stock recovery has no or less interface which has no adb sideload option. This became a crunch to flash the update which your friend got and which u dont.
This Method is Universal for all huawei devices
In order to apply ota update using this method , root access is a major requirement so be sure your device is rooted.
If u had twrp recovery , at first flash SuperSu package to root your device (Try systemless root only) .
After successfull root ,flash stock recovery from twrp and reboot system.
Step 1:
In my case b370 is the last ota i found for kiw-l22 which vsriram92 posted here . Thanks to him for posting the update before 99% users got their update :good:
Download the relevant update package (ota) which you need a relevant base package to install it on . Ex: b360 as base for b370 update
step 2:
just remember the path where u downloaded the package . Install Flashify from playstore or From Here
Select Zip file which is the third option in flashify .
step 3 :
Navigate to the path where u downloaded ota package select the update.zip (ota package).
flashify starts downloading the package to its path asks you for root access .
Grand Su permissions , Select Cwm recovery if flashify asks as the next option.
Now the phone reboots to recovery and starts flashing.
After the ota update , your device will be unrooted . so take a backup of your stock recovery by following below guide.
Enable Usb debugging and connect ur phone to pc.
navigate to adb folder and place twrp.img or recovery.img in adb folder ,open command window from the same folder and type
Code:
adb reboot bootloader
Now type
Code:
fastboot boot recovery.img
or what_ever_its_name.img
now it temporarily boots twrp , take a backup of your stock recovery and then flash twrp for permanent install and then reroot ur device.
Happy flashing :laugh::good:
it gets zip signature verification failed....the method is similar to installing the zip file directly from the recovery but that doesn't work unless zip signature is verified
rbtrai said:
it gets zip signature verification failed....the method is similar to installing the zip file directly from the recovery but that doesn't work unless zip signature is verified
Click to expand...
Click to collapse
You might have installed a zip which is not stock ota update . i haven't posted this without trying . I installed b370 with this method and made this live here .
i downloaded from the link provided above which vsriram92 posted...
rbtrai said:
i downloaded from the link provided above which vsriram92 posted...
Click to expand...
Click to collapse
Were you in b360 before doing this ?
Thanks again Gopi. Another great contribution.
vsriram92 said:
Were you in b360 before doing this ?
Click to expand...
Click to collapse
yes ofcourse
This only for rooted phone ?
I'm having honor 4x unroot and I don't know how to install the ota file. Is there any way for upgrading a phone without root option and in my phone there is no local update option
Ajith san said:
This only for rooted phone ?
I'm having honor 4x unroot and I don't know how to install the ota file. Is there any way for upgrading a phone without root option and in my phone there is no local update option
Click to expand...
Click to collapse
Nope. It was there in EMUI 3 previously. Now, we can't unless it has only update.app.
so b370 is only for the ones who gave root access to their phones?
Like your contribution. Perfectly updated to B370.
rajibie said:
Like your contribution. Perfectly updated to B370.
Click to expand...
Click to collapse
great
Hello together, I tried flashing the B360 update for my L21 with this method but unfortunately I did not succeed. I followed every step but when flashify reboots to the stock recovery nothing happens. Just nothing.
I used the file for the L21 that I linked to in this post.
Any suggestions how to get it to work?
Zacki06 said:
Hello together, I tried flashing the B360 update for my L21 with this method but unfortunately I did not succeed. I followed every step but when flashify reboots to the stock recovery nothing happens. Just nothing.
I used the file for the L21 that I linked to in this post.
Any suggestions how to get it to work?
Click to expand...
Click to collapse
Are you on B350D0003 or some earlier firmware? I'm on stock B350, just rooted with Magisk+phh's superuser, and it doesn't want to flash that big file at all; tried flashing OTA update (200MB file) and it failed at 80%, causing a damn bootloop. Gah, I thought my old phone was pain in the ass...
ShadySquirrel said:
Are you on B350D0003 or some earlier firmware? I'm on stock B350, just rooted with Magisk+phh's superuser, and it doesn't want to flash that big file at all; tried flashing OTA update (200MB file) and it failed at 80%, causing a damn bootloop. Gah, I thought my old phone was pain in the ass...
Click to expand...
Click to collapse
I'm on B350D003. After I tried the OTA instead of the full package I came across the same problem with the stock recovery, but when flashing it from TWRP it did flash it, but exited with an error.
No bootloop but as a file was missing for the full update process wifi (and probably bluetooth) are not working.
If you are interrested to solve it, have a look here. It looks like there is a way to fix the problem and we are currently investigating.
Zacki06 said:
I'm on B350D003. After I tried the OTA instead of the full package I came across the same problem with the stock recovery, but when flashing it from TWRP it did flash it, but exited with an error.
No bootloop but as a file was missing for the full update process wifi (and probably bluetooth) are not working.
If you are interrested to solve it, have a look here. It looks like there is a way to fix the problem and we are currently investigating.
Click to expand...
Click to collapse
TBH, I'm on a verge to start building LOS or PAC/Slim/whatever is properly maintained and fast for my own needs and ditch EMUI completely....
I'm searching for other firmwares now via FirmwareFinder, there is a probability that one is a leaked test or something like that, because it simply doesn't want to flash. If I find out something, I'll continue on thread you've linked, to avoid flooding this one.
Hi. Thanks for your guide.
I need to update my phone with several ota updates. I just need to repeat this guide's procedure until updated to the last ota or there is a better way to do that?
Can't update.. Its fake i think.. I m still in B360
---------- Post added at 08:39 PM ---------- Previous post was at 08:37 PM ----------
rajibie said:
Like your contribution. Perfectly updated to B370.
Click to expand...
Click to collapse
How to update step by step.. Mention it plz
Tapan Patel said:
Can't update.. Its fake i think.. I m still in B360
---------- Post added at 08:39 PM ---------- Previous post was at 08:37 PM ----------
How to update step by step.. Mention it plz
Click to expand...
Click to collapse
Just because you can't do it, that doesn't mean it's fake.
Tapan Patel said:
Can't update.. Its fake i think.. I m still in B360
---------- Post added at 08:39 PM ---------- Previous post was at 08:37 PM ----------
How to update step by step.. Mention it plz
Click to expand...
Click to collapse
Just follow the procedure and you will be done
I just randomly went to firmware finder to refresh and found a new update for the FRD-L04, did anyone attempt to install this yet?
EDIT: I tried to install it through firmware finder and it didn't pass the verification at the end
https://drive.google.com/open?id=0B4baHcoSeBbgY21CVjlPNk45YlE
https://drive.google.com/open?id=0B4baHcoSeBbgYTZiR1ZDeUpoWnc
https://drive.google.com/open?id=0B4baHcoSeBbgV0g3ejBlMXlzdkk
I have downloaded the 3 zips in this update and verified the md5 they are all good if someone figures out how to install this
krchi said:
I just randomly went to firmware finder to refresh and found a new update for the FRD-L04, did anyone attempt to install this yet?
Click to expand...
Click to collapse
I found the same... Gonna try!
Jessooca said:
How did that work out for you Jorge??
Sent from my FRD-L04 using XDA-Developers Legacy app
Click to expand...
Click to collapse
Hi!
I tried but didnt worked. There´s no option to begin the update in the app...
JorgeCS said:
Hi!
I tried but didnt worked. There´s no option to begin the update in the app...
Click to expand...
Click to collapse
Top right download full update it'll download once you hit that and remove the proxy but it won't get authorized when you go to install it.
Well the good news I see out of this even if we cannot install is that the update is finally coming after 2 months of the other versions enjoying it for that long. Hopefully it fixes the battery drain.
Sent from my FRD-L04 using Tapatalk
Received the OTA update for the B380 version on my FRD L09C185 yesterday. But no notable change in the battery life till now.
krchi said:
Top right download full update it'll download once you hit that and remove the proxy but it won't get authorized when you go to install it.
Click to expand...
Click to collapse
Yep, you can't install this...
Can you install the full firmware from B162 though?
Gus194 said:
Can you install the full firmware from B162 though?
Click to expand...
Click to collapse
You can try and tell us
Thanks for the find! Your file sizes are off unfortunately, they should be:
400MB - update_data_full_public.zip
622MB - update_full_FRD-L04_hw_usa.zip
1.3GB - update.zip
Here are the correct files: https://drive.google.com/open?id=0B0zE1Kk8sIB6M2R4QUVsN3JBOGs
Jessooca said:
So the 622mb update file is the correct B385 update file? Can i push it to the phone via adb? Or what's the best way to install it??
Click to expand...
Click to collapse
Likely you'd push both update.zip and the region specific zip to where the stock recovery is expecting, then from a powered-off state use the key combinations to force-udpate. I'm unsure why there are 3 zips this time though since B360 was only 2 zips, I haven't had time yet to look at the contents.
Telperion said:
Thanks for the find! Your file sizes are off unfortunately, they should be:
400MB - update_data_full_public.zip
622MB - update_full_FRD-L04_hw_usa.zip
1.3GB - update.zip
Here are the correct files: https://drive.google.com/open?id=0B0zE1Kk8sIB6M2R4QUVsN3JBOGs
Click to expand...
Click to collapse
Mines was just the OTA files you have the full ota files
Jessooca said:
Did you install the update you found?
Click to expand...
Click to collapse
I tried.
I think you have to extract the update.app and do the update via recovery....if I remember correctly. I'd do it now but no USB-C cable here at work...
usmcnyc said:
I think you have to extract the update.app and do the update via recovery....if I remember correctly. I'd do it now but no USB-C cable here at work...
Click to expand...
Click to collapse
Tried that, compatibility error.
Telperion said:
Tried that, compatibility error.
Click to expand...
Click to collapse
:crying:
---------- Post added at 03:30 PM ---------- Previous post was at 02:44 PM ----------
In theory, we could also just extract the recovery.img, system.img and vendor.img and flash via fastboot.....or no? I know that's generally the way I've flashed things on my Shield TV
usmcnyc said:
:crying:
---------- Post added at 03:30 PM ---------- Previous post was at 02:44 PM ----------
In theory, we could also just extract the recovery.img, system.img and vendor.img and flash via fastboot.....or no? I know that's generally the way I've flashed things on my Shield TV
Click to expand...
Click to collapse
Just tried that too, boot, recovery, and system will flash but vendor fails. When I load to the system it still shows B360 but certain parts of the OS don't work -- can't access Developer Options, for example. It seems as if this package just doesn't work right.
Update: If anybody else wants to attempt it, remove all PIN/password protection first. I had to factory reset.
Telperion said:
Just tried that too, boot, recovery, and system will flash but vendor fails. When I load to the system it still shows B360 but certain parts of the OS don't work -- can't access Developer Options, for example. It seems as if this package just doesn't work right.
Update: If anybody else wants to attempt it, remove all PIN/password protection first. I had to factory reset.
Click to expand...
Click to collapse
Sounds like we're stuck...thanks for trying all that though, saved me a huge headache...
usmcnyc said:
Sounds like we're stuck...thanks for trying all that though, saved me a huge headache...
Click to expand...
Click to collapse
Of note is that the 72309 firmware (B360) zips can be flashed from TWRP with no issue. This zip however fails to install.
Things I tried which failed:
Unpacking UPDATE.APP and force-updating from /external_sd/dload/ folder
Flashing extracted images from bootloader*
Modifying updater-script and flashing in TWRP (mountencrypt was throwing an error, others too)
Updating updater-script and update-binary and flashing in TWRP (same errors)
Flashing images from bootloader, boot and system worked but vendor failed, but the device did boot. It didn't, however, show the new software version -- but that may be because the software version is read from the vendor partition which wouldn't flash. In any event, flashing this way the device was unstable. I couldn't set a screen PIN and Developer Options would crash the Settings menu when I attempted to access it.
Someone more skilled than me would need to extract the contents of all 3 zips and make one TWRP-flashable zip.
Telperion said:
Of note is that the 72309 firmware (B360) zips can be flashed from TWRP with no issue. This zip however fails to install.
Things I tried which failed:
Unpacking UPDATE.APP and force-updating from /external_sd/dload/ folder
Flashing extracted images from bootloader*
Modifying updater-script and flashing in TWRP (mountencrypt was throwing an error, others too)
Updating updater-script and update-binary and flashing in TWRP (same errors)
Flashing images from bootloader, boot and system worked but vendor failed, but the device did boot. It didn't, however, show the new software version -- but that may be because the software version is read from the vendor partition which wouldn't flash. In any event, flashing this way the device was unstable. I couldn't set a screen PIN and Developer Options would crash the Settings menu when I attempted to access it.
Someone more skilled than me would need to extract the contents of all 3 zips and make one TWRP-flashable zip.
Click to expand...
Click to collapse
There's a 1.9gb OTA on firmware finder...I'd download it here at work but the internet is too slow, it'd take hours.
Hello, anybody got NXT-L29C432B580 full zip?
It appears on http://hwmt.ru/oth/HWFF/info/view.php?find_model=NXT-L29C432 but I'm unable to download it.
I've downloaded b581, but I can't flash (or dload) it over b560 (I assume that I need to do b560 -> b580 -> b581).
A new update do fast ? Have anyone had success to install this without root?
Boosik said:
Hello, anybody got NXT-L29C432B580 full zip?
It appears on http://hwmt.ru/oth/HWFF/info/view.php?find_model=NXT-L29C432 but I'm unable to download it.
I've downloaded b581, but I can't flash (or dload) it over b560 (I assume that I need to do b560 -> b580 -> b581).
Click to expand...
Click to collapse
I've successful to download the full package of the B580 via Firmware Finder app but that's all! I did'nt test more. Because at moment where I've been motivated to test it, people (OldDroid) talked us about of B581. I don't see the B581 with FF, so I can't have the full package and I tried the B581 via dload. Doesn't work like B580! If I install it via TWRP, I miss some apps... and sometimes they are really important in order to start a fresh installation, like keyboard. I've already had this issue.
Finally, i'm not sure it will work with TWRP like I want.
franzyroy said:
I don't see the B581 with FF, so I can't have the full package and I tried the B581 via dload.
Click to expand...
Click to collapse
Hope this help!
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G753/g104/v84296/f1/full/update.zip
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G753/g104/v84296/f1/full/public/update_data_full_public.zip
http://update.hicloud.com:8180/TDS/...l/NXT-L29_hw_eu/update_full_NXT-L29_hw_eu.zip
Tony66 said:
Hope this help!
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G753/g104/v84296/f1/full/update.zip
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G753/g104/v84296/f1/full/public/update_data_full_public.zip
http://update.hicloud.com:8180/TDS/...l/NXT-L29_hw_eu/update_full_NXT-L29_hw_eu.zip
Click to expand...
Click to collapse
Cannot flash this
unable to install
Hi,
I'm also unable to install this firmware... when attempting to flash it I get errors (error 7).
process followed:
- format data
- wipe (all, but sd card)
- install root
- install hw_eu
- install public
- install update.zip
- reboot
- factory reset
The build number states NRD90M test-keys instead of the actual build number.
How to properly go to that L29 ROM?
I installed 581 by extracting the .img files from update.app. Couldn't do it any other way. I had issues with tethering greyed out and now it works. That's about all it did for me.
NMonster69 said:
I installed 581 by extracting the .img files from update.app. Couldn't do it any other way. I had issues with tethering greyed out and now it works. That's about all it did for me.
Click to expand...
Click to collapse
Could you explain the steps to do the install like u did?
Successful update by Huawei updater 2.0 + HiSuite (proxy activate)!
kuprij said:
Could you explain the steps to do the install like u did?
Click to expand...
Click to collapse
I used the Huawei update extractor to get the .img files then fasboot flashed the .img files
kuprij said:
Successful update by Huawei updater 2.0 + HiSuite (proxy activate)!
Click to expand...
Click to collapse
What version do you have before?
Chisetdel31260 said:
What version do you have before?
Click to expand...
Click to collapse
B560
NMonster69 said:
I used the Huawei update extractor to get the .img files then fasboot flashed the .img files
Click to expand...
Click to collapse
Step by Step please! (system, recovery, boot) TWRP-Version?
Firmware before?
Everything works?
Thanks
kuprij said:
Successful update by Huawei updater 2.0 + HiSuite (proxy activate)!
Click to expand...
Click to collapse
From where have you downloaded the B581? Can you give us a link please?
freaked9 said:
From where have you downloaded the B581? Can you give us a link please?
Click to expand...
Click to collapse
http://hwmt.ru/oth/HWFF/info/view.php?find_model=NXT-L29C432
---------- Post added at 12:55 PM ---------- Previous post was at 12:46 PM ----------
Tony66 said:
Step by Step please! (system, recovery, boot) TWRP-Version?
Firmware before?
Everything works?
Thanks
Click to expand...
Click to collapse
Firmware before was B560
Tethering works for me now.
I used Huawei update extractor to extract the .img files from update.app
I used SRKTool to make it easy to install the .img files. copied the img files into the \unbrick directory
Put phone into fastboot mode (power plugged in, vol down, then power) (Used option 7 then 14 to install using SRK tool.)
Did the remaining files manually using the platform tools (fastboot flash boot boot.img [for example])
kuprij said:
Successful update by Huawei updater 2.0 + HiSuite (proxy activate)!
Click to expand...
Click to collapse
can you explain how you did it?
i know for b560 exists a method,but i cant find it xD
Step by step install B581 hisuite proxy ? please
K4Y3R said:
can you explain how you did it?
i know for b560 exists a method,but i cant find it xD
Click to expand...
Click to collapse
https://forum.xda-developers.com/mate-8/general/nxt-l29c185b580-frimware-t3595441/post72196935
---------- Post added at 07:12 PM ---------- Previous post was at 07:12 PM ----------
Dindi999 said:
Step by step install B581 hisuite proxy ? please
Click to expand...
Click to collapse
The same:
https://forum.xda-developers.com/mate-8/general/nxt-l29c185b580-frimware-t3595441/post72196935
kuprij said:
https://forum.xda-developers.com/mate-8/general/nxt-l29c185b580-frimware-t3595441/post72196935
---------- Post added at 07:12 PM ---------- Previous post was at 07:12 PM ----------
The same:
https://forum.xda-developers.com/mate-8/general/nxt-l29c185b580-frimware-t3595441/post72196935
Click to expand...
Click to collapse
First thank you for the link , but it wont work for me.. i already tried b580 and 581
NMonster69 said:
http://hwmt.ru/oth/HWFF/info/view.php?find_model=NXT-L29C432
---------- Post added at 12:55 PM ---------- Previous post was at 12:46 PM ----------
Firmware before was B560
Tethering works for me now.
Click to expand...
Click to collapse
Hope they float this out through the official (ie: built in huawei update) site because I noticed tethering isn't
working on 560
Hey Guys,
i just wanted to share the manual update and to Oreo Beta with you. Since i struggled a long time to find the right thing, i just want to have it in one thread for you all.
First of all you need a BND-L21 Honor7X that's bootloader is unlocked!
Step by Step - flashing EMUI 8 Oreo BETA:
- Download and flash the TWRP Image (credits to Sudeep)
Code:
fastboot flash recovery twrp_openkirin_sudeep.img
- Download all the files and put them on your SDCard in your Honor7X´(credits to Eduardo Alonso)
update.zip
update_data_full_public.zip
update_full_BND-L21C_hw_eu.zip
BND-RECOVERY-NoCheck.img
- Boot into TWRP and go to Advanced > Terminal
Now we do the method (credits to olddroid)
- Type in these commands:
Code:
dd if=/external_sd/BND-RECOVERY-NoCheck.img of=/dev/block/bootdevice/by-name/recovery
dd if=/external_sd/BND-RECOVERY-NoCheck.img of=/dev/block/bootdevice/by-name/recovery2
- If those went well type these as next:
Code:
echo --update_package=/sdcard/update.zip > /cache/recovery/command
echo --update_package=/sdcard/update_data_full_public.zip >> /cache/recovery/command
echo --update_package=/sdcard/update_full_BND-L21C_hw_eu.zip >> /cache/recovery/command
(Those Arrows (>) and lines (-) are important! Keep them as in command given!)
- If those went well aswell type:
Code:
reboot recovery
- It will try to install the new Oreo EMUI 8 BETA update
- If it's done Reboot to Recovery (Both Volume Keys + Power) and do a factory reset with Stock Recovery
- Be happy with your EMUI 8 on L21!
(Credits: olddroid, Sudeep, Eduardo Alonso)
Download (Click me)
Mirror (Click me)
If you want to Root your device after you have updated to Oreo, follow this Guide:
https://forum.xda-developers.com/ho...agisk-root-honor-view-10-mate-10-pro-t3749280
Feel free to Mirror it. You can send me the Mirror via Telegram
https://t.me/IceToast
Thank you for this!
To clarify this is the full official firmware package for BND-L21 8.0.0.302(C432log). So other update methods like dload should work as well. If you're already rooted you can skip the TWRP step and just create the recovery commands as root.
I skipped the factory reset without issues so far when updating from BNDL21C432B102.
The only issue for me is that Magisk no longer works, that is the boot crashes (loops) with some undefined symbol error. Is it working for anybody on Oreo on the 7x?
Thanks for your tutorial. Upgrading from BNDL21C432B102 worked like a charm.
This method work on BND-L21C432B123 and unlocked bootloader and twrp a must?
Anybody try via stock recovery dload from SD ..thanks
Sent from my BND-L21 using Tapatalk
@IceToast, here is a mirror link you could use in the OP. http://downloadmirror.co/Wqk/Honor7x-Oreo-update-download.zip
Contains all your files, including the How To.txt one.
jhass said:
Thank you for this!
To clarify this is the full official firmware package for BND-L21 8.0.0.302(C432log). So other update methods like dload should work as well. If you're already rooted you can skip the TWRP step and just create the recovery commands as root.
I skipped the factory reset without issues so far when updating from BNDL21C432B102.
The only issue for me is that Magisk no longer works, that is the boot crashes (loops) with some undefined symbol error. Is it working for anybody on Oreo on the 7x?
Click to expand...
Click to collapse
Yes i followed the Magisk guide to install it. https://forum.xda-developers.com/ho...agisk-root-honor-view-10-mate-10-pro-t3749280 This works.
And yes, as an C432 Device u could skip the factory reset, but its not recommended. If you have any errors, just reset it.
itskapil said:
@IceToast, here is a mirror link you could use in the OP. http://downloadmirror.co/Wqk/Honor7x-Oreo-update-download.zip
Contains all your files, including the How To.txt one.
Click to expand...
Click to collapse
Thanks i will add this to my Post
IceToast said:
Yes i followed the Magisk guide to install it. https://forum.xda-developers.com/ho...agisk-root-honor-view-10-mate-10-pro-t3749280 This works.
Click to expand...
Click to collapse
Weird, I thought these patches were in the official 16.0 release which I tried.
followed but after reboot recovery command i just get software install failed (after like 20 mins typing the commands ) errrr
is the beta stable, or not?
---------- Post added at 05:33 PM ---------- Previous post was at 04:56 PM ----------
DoobyDroid said:
followed but after reboot recovery command i just get software install failed (after like 20 mins typing the commands ) errrr
Click to expand...
Click to collapse
adb shell - and you can copy and paste directly on your DEVICE!
johination said:
is the beta stable, or not?
---------- Post added at 05:33 PM ---------- Previous post was at 04:56 PM ----------
adb shell - and you can copy and paste directly on your DEVICE!
Click to expand...
Click to collapse
It's not so much the commands, am I doing right by just putting zips on sd as they are or do you have to unzip them and put on sd or into dload file on sd, thanks
Sent from my BND-L21 using Tapatalk
Must of been a typo in command Lol worked this time sweet as
Nice one [emoji2][emoji7][emoji106]
Sent from my BND-L21 using Tapatalk
[emoji16][emoji7]
Sent from my BND-L21 using Tapatalk
Hi !
Thanks for the update!
Is it necessary to have an official ROM backup If so, how do you make one with TWRP or if there are others hanging out on the Internet?
Thanks a lot !
Does the display scaling still work properly unlike the mate 10 which only changes certain parts on Emui 8 ie notification panel and icons
johination said:
is the beta stable, or not?
Click to expand...
Click to collapse
Since it's a Beta, its not Stable as a Stable release Lol. But it seems to be pretty stable i guess. Many say its perfect.
I personally dont use Emui 8 i went straight to RRos. But i may go back to Emui.
DaRkLinK_35 said:
Hi !
Thanks for the update!
Is it necessary to have an official ROM backup If so, how do you make one with TWRP or if there are others hanging out on the Internet?
Thanks a lot !
Click to expand...
Click to collapse
It is not necessary! But since no L21 Firmware (except Oreo) is released yet, i dont think there is and cuz' Emui encrypts the internal storage its not easy to make one.
r8dooo said:
Does the display scaling still work properly unlike the mate 10 which only changes certain parts on Emui 8 ie notification panel and icons
Click to expand...
Click to collapse
Dont exactly get what you're asking for. But i recommend to look in other Beta threads for that.
Oh and for all, i can't recommend ADB Shell method, since many user got errors with that.
Will this continue to get ota updates as and when they come ?
Sent from my BND-L21 using Tapatalk
Thanks.
@IceToast
Thanks for this. Finally L21.
Why wont you pass this to the Development Area ?
There are L22, L24, etc....
Anyways, thanks for this
RSGI said:
@IceToast
Thanks for this. Finally L21.
Why wont you pass this to the Development Area ?
There are L22, L24, etc....
Anyways, thanks for this
Click to expand...
Click to collapse
I'm not able to move this Thread
Thank you so much! Upgrading from L21C432B101 worked like a charm. Literally no problems whatsoever
Only question though is will we get OTA updates or will we have to manually update like with this version?