Hi! I have Sharp 304sh from Taobao and I broke It. Using TWRP I wanted to change chinees ROM to stock And now my device don't load beyond the logo. And my PC (and other PC too) don't see the device. Please help
Hi there
i have the same problem
my phone aquos 304 there are no available physical volume rocker button
i forget the password patern
custom cable data with R jumper to ID pin with zadig software cannot flash the twrp
could someone help me out of this
thx
Hold your power button alot of time, if it vibrate 2 time stop hold your power button and tada you can play your self with twrp or some recovery on your phone
Dont tell much people about that and make thier hard to unlock it
Related
Hello,
I wanted to ask if someone clashed with problem like that and knows how to solve it. I had 1.66 rom eastern euope and installed 2.08hspl, tried to install latest magldr and I am guessing problem occured because I didnt installed latest radio. Now when I am turning on the phone it shows white screen and green logo and stuck. Tried turning of the phone and holding - volume button when turning on that didnt make any difference can someone help me to revive my phone ?
So you tried to get into bootloader, but the thing is you have to try harder.
Bootloader should work just fine.
So again, turn of your phone. while the phone is turned off, keep the vol down, and press the power button.Release the power button, but keep the vol down pressed.
You can try the other way: hold the vol down pressed and reset the phone(red button on the back).
If you want to use the SD card method to flash something you still have to enter the bootloader, so you must keep trying.
Forgot to ask: did you manage to enter the bootloader or not, cause you only said it did not make any difference????.What does that mean?
I already trying to enter bootloader for the five hours, so I guess it's impossible, also tried that thing with red button it didnt load up that bootloader screen. The thing is that holding volume key down didn't work for me before to get into bootloader even when the phone was ok but it did install all roms which I tried so I didnt think that this would be problem either apparantely it is... Maybe youu have some other suggestions how to fix it ?
If you can make the pc recognize the HD2 then you can flash anything.
But i think that this is only possible in bootloader or windows or android.
So this is a problem.
No ideea for now.
Anyone help???
But you *do* push both vol. down and power buttons and keep them pushed until the screen turns on, don´t you?
I didn´t get into the bootloader as long as I didn´t kept both buttons pushed long enough... had to learn the "timing" kind of...
my verizon xperia is not recognized by either pc companion or seus. I am trying to do a hard reset due to the fact the lockscreen doesnt work. I have read that I can press and hold the back and search keys on front while powering on to factory reset the phone, however that does not seem to be the case. Can anyone give me some suggestions if the two button factory reset does work and that maybe I am just doing it wrong. And any suggestions as to how to get my phone to connect with seus so I can reset if teh 2 button trick is indeed not an option. Thank you to all in advance.
Doesnt anyone have an idea? I follow seus instructions. Power off wait 30 seconds, then plug in the usb cord to the pc, then press and hold the back button then inserting the usb cable into the phone... and then I wait for it to connect which it doesnt.
Please more informations.
Is your phone rooted?
Is your bootloader unlocked?
are alle drivers installed on your computer?
after that i can help you
greetz -Blizzrar-
No the device is not rooted or bootloader unlocked. it is the verizon version. Thank you for your help...
if you hold the "BACK" button, the LED turns green?
Are you sure that you have all drivers installed for Zeus mode?
plz Check that out in your systeminformations / hardware / SEMC Flash device
this must be installed. Maybe google this and downlodet this driver.
wait for reply
When i press the back button the light is still blue. I will google the drivers you mentioned. The only drivers I hae installed so far are the s1fastboot. What is ZUES? Thank you again
you will repair your phone with sony pc-companion right?
This works only in SEMC / ZEUS mode. The Led is than still green.
in the moment you are in fastboot mode.
then you holding the "SEARCH" botton and plugged your device the Led is blue.
You are in the wrong mode^^
Please holding the BACK botton, not the SEARCH botton.
sorry my english is bad i hope you can understand me
I want to repair it with the Sony update software if possible. However no matter what I do the phones light is blue, and pressing the back button does not change it to green. Also as I am not able to go beyond the lockscreen I am unable to enter into the phones settings.... I tried to do a search for the drivers you mentioned but I am still not able to find anything... the only drivers I have installed are the S1Fastboot drivers..
thats bad that you can´t go in SEMC Mode.
Please look in the developers area of the xperia play. search the topic to unlock your bootloader.
Unlock it and use the fastbootmode to recover your device.
Ok, I will start looking there. Thank you for your assistance blizzrar, I really appreciate your feedback and guidance
OK, I managed to really really screw my phone up!!!
I installed a 4.4.2 rom (crDroid) and everything was working fine.... USB debugging on and rooted.
Next I started playing with LCD Density settings and managed to get get a device that won't show anything past the LG logo.... just a blank screen.
I have tried connect it to my computer and using adb to push a new build.prop to fix it, but I can't seem to get this thing recognized via adb anymore.... all I see is an "unauthorized" device and I can't see the screen (b/c it blank) to make any changes to actual device.
I am really really worried that I have completely borked this device.... PLEASE PLEASE PLEASE HELP ME!!!!
Another thing I should note.... I have tried many many times to boot directly into CWM (which I have installed version 6.0.4.4.). Unfortunately I think the LCD problem is killing me here.... I hold down the power+vol-down and then press them again when I hit the LG logo, but at this point the thing just goes blank.... I never actually see a CWM screen.
Again, thank in advance for your help... I am very very desperate and really have no idea what to do at this point.
OK, sorry for the freakout... I got this sorted out... it turns out I was following the wrong instructions on how to get into hardware reset mode.... for the vs980 you need to do the following...
1. press and hold power + vol-down
2. as soon as you see the LG Logo...
- release the power + vol-down buttons
- then immediately re-press only the power button
This should do it... some people were (I'm guessing for the other versions of the G2) were saying you needed to "re-press" both the power and the vol-down button and this was not working for me.
Hello guys, I'm new here and I hope you can help me out.
Let me make the story short.
My phone's screen broke and I replaced.
In that processes I lost the rubber that stick
to the panel of the volume. I was fine with that since my phone
in vibrate mode and I really don't use ring tone in my daily basis.
I tried to download Android 5.0 lollipop and flash it.
How did I get there? well since I did not have a volume button,
I downloaded an app that restarted my phone and got me into
fastboot mode without the key (I did got me where I wanted).
Then the problem was that in the middle of writing the .img
the freaking cheap bastard micro usb unplugged!!!
BAMM!! phone now is bricked, I cannot get into recovery/fastboot mode
since I cannot press the volume key and my phone is bricked.
I tried going through fastboot mode via my computer again,
but the computer doesn't recognize the device since it still
looping there forever at the google logo. I try installing USB
DRIVERS to see if I could do some "magic" haha. Got
error "This device cannot start ..." And still at the same problem.
I know I can get back to my recovery if order the part for the volume
key, I ordered the part to replace it, but trust me I was 3 weeks without
my phone and now this problem
Is there any way that I can get to fastboot mode to factory reset my phone
without volume key with a bricked forever looping a "google" logo ? :fingers-crossed: :fingers-crossed:
I appreciate any help.
vadeld said:
Hello guys, I'm new here and I hope you can help me out.
Let me make the story short.
My phone's screen broke and I replaced.
In that processes I lost the rubber that stick
to the panel of the volume. I was fine with that since my phone
in vibrate mode and I really don't use ring tone in my daily basis.
I tried to download Android 5.0 lollipop and flash it.
How did I get there? well since I did not have a volume button,
I downloaded an app that restarted my phone and got me into
fastboot mode without the key (I did got me where I wanted).
Then the problem was that in the middle of writing the .img
the freaking cheap bastard micro usb unplugged!!!
BAMM!! phone now is bricked, I cannot get into recovery/fastboot mode
since I cannot press the volume key and my phone is bricked.
I tried going through fastboot mode via my computer again,
but the computer doesn't recognize the device since it still
looping there forever at the google logo. I try installing USB
DRIVERS to see if I could do some "magic" haha. Got
error "This device cannot start ..." And still at the same problem.
I know I can get back to my recovery if order the part for the volume
key, I ordered the part to replace it, but trust me I was 3 weeks without
my phone and now this problem
Is there any way that I can get to fastboot mode to factory reset my phone
without volume key with a bricked forever looping a "google" logo ? :fingers-crossed: :fingers-crossed:
I appreciate any help.
Click to expand...
Click to collapse
Im not sure why your text is like this? But paraphrasing buddy comes a long way
Just hold the power button, until it dies, or just let it die in general since your volume button (You only need Vol down and Power) to power it off completely. Since your Volume keys are gone, the best solution is to wait for the replacement before doing so, unless you can get the contact keys to trigger the Volume button, you're in a loss atm. No OS or Volume keys means you can't trigger ADB commands or boot into fastboot. Just wait it out I guess?
Hello to everyone,
I received a system notification this morning which was telling me that there was a new software update for the Zenfone 3 Max. So I've clicked on it to update the system, and, during the update, something went wrontg and it "crashed", rebooting in a strange korean (?) screen:
Now I can't boot properly the Zenfone and if I try to move inside the screen it just changes some english text from eMMC or FM to BT or GPS. It's like it is doing a device check and something isn't working.
It can't be turned off, so I just let the battery go dead to see if this would fix the issue.
I've charged it while it was switched off, and after a couple of minutes it turned on with the same korean (?) screen. I've also tried the hard reset by keeping pressed the power on button, but it only went off.
The last thing I've tried is to connect it via USB on my laptop while it is in this strange screen and checked that is recognised by the ADB. I've never unlocked the bootloader or ever rooted this model, so the response of the command "adb devices" is a model and the text "Unauthorized".
Is it something that I can actually do? I'd like to try an hard reset or force it to go in recovery mode and try to reinstall the firmware... but since the device is "unauthorized" I'm not sure that it will let me flash the firmware...
Do you have any advice on how to handle this situation?
Thanks in advance
(I do apologize for my grammar mistakes)
My English is really really bad, so try to understand this
Frst if ur phone is hang or stock in any ways u can reboot or power it off by pressing the power button for atleast 10 sec. Press and hold.
Second u can reinstall the firmware in any case even if ur phone is dead.
Frst u need to install the usb driver
https://www.youtube.com/watch?list=...AFIAVgC&v=y-oDWXbhiC0&mode=NORMAL&app=desktop
Then u can reinstall the firmware using the following files
https://m.youtube.com/watch?list=PL4PNn1kmbOalk-kuEUO3hrJWA9hOAzl9Z&v=rh2m1Pgof2s and u need the latest firmware updates in zip.
U can get from here
https://www.asus.com/ph/Phone/ZenFone-3-Max-ZC520TL/HelpDesk_Download/
I hope u can figure it out.
We have the same phone model so it should work for you.
whyterhomer said:
My English is really really bad, so try to understand this
Frst if ur phone is hang or stock in any ways u can reboot or power it off by pressing the power button for atleast 10 sec. Press and hold.
Second u can reinstall the firmware in any case even if ur phone is dead.
Frst u need to install the usb driver
https://www.youtube.com/watch?list=...AFIAVgC&v=y-oDWXbhiC0&mode=NORMAL&app=desktop
Then u can reinstall the firmware using the following files
https://m.youtube.com/watch?list=PL4PNn1kmbOalk-kuEUO3hrJWA9hOAzl9Z&v=rh2m1Pgof2s and u need the latest firmware updates in zip.
U can get from here
https://www.asus.com/ph/Phone/ZenFone-3-Max-ZC520TL/HelpDesk_Download/
I hope u can figure it out.
We have the same phone model so it should work for you.
Click to expand...
Click to collapse
First of all, thank you for the explanation, as far as I've searched this seems to be the "factory mode" screen of the asus zenfone max 3 with the chinese language setted... And the fact is that this mode is used for test purposes only, in fact if I randomly choose any option it just seems to test a random phone function. Anyway, I've tried to reboot it by choosing the 8th option, which is supposed to reboot the phone normally, and it kept on going in that screen again. I've also tried to reboot by forcing the reboot via (Vol Down + Power) buttons together.. and for my bad luck it still resets in this "factory mode".
I watched the video and not sure about it because I'm not familiar with SP Flash Tool: does my zenfone needs to have the bootloader unlocked? or it should have been rooted? Will I be able to flash the firmware while the phone is in the status, even if in ADB devices it is shown as "Unauthorized" ?
I'm asking all these questions because I've never done any firmware operations on this smartphone, I've only made ordinary system updates.
Thanks in advance for your patience and your attention!
Pressing volume down + power is going to that screen. I dont know if Chinese or Korean
Pressing volume up + power key for default recovery mode screen,
Press and hold the power key is for normal boot.
I dont know if zen3max need a bootloader unlock.
Because im able to install a custom recovery in my zen3max and my phone is rooted and im able to install back the stock recovery so i dont get any trouble Everytime i received a notification update.
Well if u r worried. Get another smartphone and use the google translator with the camera to translate that Chinese language on ur zenfone 3 max. Maybe u can find the format option or clear cache blah blah blah.
whyterhomer said:
Pressing volume down + power is going to that screen. I dont know if Chinese or Korean
Pressing volume up + power key for default recovery mode screen,
Press and hold the power key is for normal boot.
I dont know if zen3max need a bootloader unlock.
Because im able to install a custom recovery in my zen3max and my phone is rooted and im able to install back the stock recovery so i dont get any trouble Everytime i received a notification update.
Well if u r worried. Get another smartphone and use the google translator with the camera to translate that Chinese language on ur zenfone 3 max. Maybe u can find the format option or clear cache blah blah blah.
Click to expand...
Click to collapse
When you said that volume down + power key is the combo of keys to press to go in that screen... it kinda rang me a bell: recently my smartphone fell and it got damaged on the right edge, causing the volume down button to get inside the cover, and now it is like unpushable... I've never powered off my zenfone until I had to do this system update. So I thought that probably there isn't anything wrong with the firmware, it just keeps going in factory mode each time I try to power it on due to the fact that the volume down seems to be pressed all the time. So I decided to contact the ASUS support team to give it to them and let them repair the buttons.
Thanks for the info!
so must be thats the problem boot looping in to that screen because the volume down is broken. I guess.
Well thats the best u can do to fix it.