I have lg g2 sprint version. I have unlocked it by following a tutorial on youtube. On the ui there was a message that there is software update and i tapped to install it, but it was stuck on fastboot mode started udc_start() so i followed tutorial from a forum and fastfbooted boot aboot recovery and laf, but forgot to run fastboot reboot and turned off and on the phone. Now when I try to start the phone it shows the lg logo and after that only the led is flashing no matter if it's charging or not. Any ideas what to do? I have plugged it in to power it, but I am not sure whether it's charging now.
I can enter in download mode by pressing volume up and power button, but I don't have pc near me to try to flash to stock.
lolopopolo said:
I have lg g2 sprint version. I have unlocked it by following a tutorial on youtube. On the ui there was a message that there is software update and i tapped to install it, but it was stuck on fastboot mode started udc_start() so i followed tutorial from a forum and fastfbooted boot aboot recovery and laf, but forgot to run fastboot reboot and turned off and on the phone. Now when I try to start the phone it shows the lg logo and after that only the led is flashing no matter if it's charging or not. Any ideas what to do? I have plugged it in to power it, but I am not sure whether it's charging now.
I can enter in download mode by pressing volume up and power button, but I don't have pc near me to try to flash to stock.
Click to expand...
Click to collapse
The situation after a couple restarts is:
When I put to charge the lg logo appears and the led is flashing from yellow to blue
if I hold down and power button it says "Recovery mode. Loading..." and nothing happens
If I hold up and power button it enters download mode
Can I charge the phone in order to flash it to stock?
p.s. I am turning it off by holding the power button for ~20 sec
Hello, I have a problem with my storm. Two days ago I received it and flashed the then latest cm13 and its corresponding recovery. Everything seemed to work just fine until yesterday when there appeared to be an ota update. After the download finished, the phone rebooted itself and is since then stuck with a black flickering screen. Every attempt to start the phone using recovery or bootloader seems to fail, as the phone keeps showing me the black flickering screen, no matter the combination of keys (vol+/vol-) I use to turn it on. If during the black screen I plug the phone to the computer adb can actually see the phone but says it's not authorized to perform any command. On the other hand fastboot won't even see the device.
Is there anything else I can try before sending it back to wileyfox?
Thank you in advance
I've made some progress, I found out that the device can be forced to Qualcomm HS-USB QDLoader 9008 mode by turning it off and then connecting it to usb while holding vol+ and vol-.
I've also found the stock firmware at https://cyngn.com/support.
Now it would be great if somebody could help me, and the others in my situation, to figure the wole QFIL unbricking out, because I'm overwhelmed, and can't seem to find the right info on google.
Thanks to anyone who'll care to help, or share some info
I had a similar issue so have created a thread with stock recovery instructions, which resolved the issue for me.
http://forum.xda-developers.com/wileyfox-storm/help/how-to-flash-stock-images-brick-recovery-t3319617
I hope this helps.
miSAKe said:
I had a similar issue so have created a thread with stock recovery instructions, which resolved the issue for me.
http://forum.xda-developers.com/wileyfox-storm/help/how-to-flash-stock-images-brick-recovery-t3319617
I hope this helps.
Click to expand...
Click to collapse
Thank you for your reply.
Unfortunately this does not seem to be applicable to my case because on my device fastboot mode doesn't seem to work.
I've spent an entire afternoon trying to get it to boot to fastboot mode using different vol keys combinations and timings, but none of them seemed to work. No matter the combination, it just kept booting to a black screen flickering.
I'm starting to think that it could be some problem unrelated to my actions because if, as I think it is, recovery mode and fastboot mode are two separated things, nothing I did would justify this kind of behaviour.
maxxie00 said:
Thank you for your reply.
Unfortunately this does not seem to be applicable to my case because on my device fastboot mode doesn't seem to work.
I've spent an entire afternoon trying to get it to boot to fastboot mode using different vol keys combinations and timings, but none of them seemed to work. No matter the combination, it just kept booting to a black screen flickering.
I'm starting to think that it could be some problem unrelated to my actions because if, as I think it is, recovery mode and fastboot mode are two separated things, nothing I did would justify this kind of behaviour.
Click to expand...
Click to collapse
Sorry to hear you are still having trouble, it does sound like the same issue, was a CM13 update from the last couple of days, upon reboot I saw the wileyfox logo but when the Cyanogen logo would normally show during boot it displayed a black screen, which would flicker every few seconds. Holding vol- and power to reboot resulted in the same thing so I was unable use recovery.
When the display was black and connected via USB I was able to see the device using ADB but like you no commands were authorised.
Leaving the phone plugged in via USB and holding down vol+ and power until it rebooted I was able to enter fastboot, once the fastboot prompt was displayed on the screen I attempted using fastboot to boot from a custom recovery, unfortunately that just resulted in the same blank screen for me. I also tried booting the stock recovery with the same result, I admit I did not try many older CM recoveries, but I wanted to revert to CM12.1 anyway, as the accelerometer and gyroscope not working in CM13 at the moment is no good for me.
Only thing that worked was a stock restore, so I think something beyond the recovery got broken as you could not even boot a previously working recovery.
For the sake of sanity it may be work getting someone else try booting it into fastboot before resorting to Wileyfox support. Though your phone is really new so could claim a refund or replacement from the seller, that would probably be faster.
FYI if you do end up sending it to Wileyfox support they do flash it back to stock, I had a broken screen replaced, was repaired and back to me in just under 2 weeks.
What would be exactly the timing for it to boot to fastboot mode?
Because I just tried (again...) to plug it to the computer while powered off, then it powered on on its own.
After that I rebooted it by holding together power and vol+ and immediately after it rebooted (right after the vibration) I let the power button go and kept holding the vol+ until the black screen appeared again... no fastboot
maxxie00 said:
What would be exactly the timing for it to boot to fastboot mode?
Because I just tried (again...) to plug it to the computer while powered off, then it powered on on its own.
After that I rebooted it by holding together power and vol+ and immediately after it rebooted (right after the vibration) I let the power button go and kept holding the vol+ until the black screen appeared again... no fastboot
Click to expand...
Click to collapse
Hi,
Just tried a few combinations to check timings for you.
Powered off, not plugged in, holding vol+ while plugging in phone end of usb connected to computer, keep holding vol+ -> boots straight to fastboot.
Powered on, already connected to computer via usb, holding vol+ and power, release power when vibrates to indicate reboot but keep holding vol+ -> boots straight to fastboot.
Are you seeing the black and white Wileyfox logo when first booting? When going to fastboot it should skip that. If you are not seeing the logo it might not show the fastboot screen either. You can try following the steps above and then issuing fastboot devices from a command/shell session to see if you are in fastboot mode.
I hope that is of some help.
Thank you but I can confirm that neither of these combinations work for me. When rebooted/powered the device shows the wileyfox's logo.
If I use your first method it just seems to freeze on the wileyfox's logo screen, and the computer won't even see it (it's not listed on the usb devices list) so fastboot's not an option.
If I use your second method, or any other I tried, it shows me the wileyfox's logo and then proceeds to the black screen, which can be seen just by adb (not fastboot) but I'm not authorized to perform any action like you described for your issue.
I'm out of ideas so I'm sending it back and getting it replaced. On the cyanogenmod irc they told me that to brick it like that it cannot be done just by accident but it should require a lot of deliberate effort, and that just installing cm13 + recovery doesn't justify this problem nor does an OTA update, so it's probably some other (hardware?) issue with a very bad timing.
I'm kind of sure it's not the vol+ button that's damaged, because if I leave the device powered off and then proceed to plug the USB while holding together vol+ and vol- it powers on, but the screen stays off meaning the Qualcomm HS-USB QDLoader 9008 mode has been triggered.
Anyway thank you for your help, I could rule out my inability to start the fastboot mode and blame it on the phone xD
Hope I'll be luckier with the next one...
maxxie00 said:
Thank you but I can confirm that neither of these combinations work for me. When rebooted/powered the device shows the wileyfox's logo.
If I use your first method it just seems to freeze on the wileyfox's logo screen, and the computer won't even see it (it's not listed on the usb devices list) so fastboot's not an option.
If I use your second method, or any other I tried, it shows me the wileyfox's logo and then proceeds to the black screen, which can be seen just by adb (not fastboot) but I'm not authorized to perform any action like you described for your issue.
I'm out of ideas so I'm sending it back and getting it replaced. On the cyanogenmod irc they told me that to brick it like that it cannot be done just by accident but it should require a lot of deliberate effort, and that just installing cm13 + recovery doesn't justify this problem nor does an OTA update, so it's probably some other (hardware?) issue with a very bad timing.
I'm kind of sure it's not the vol+ button that's damaged, because if I leave the device powered off and then proceed to plug the USB while holding together vol+ and vol- it powers on, but the screen stays off meaning the Qualcomm HS-USB QDLoader 9008 mode has been triggered.
Anyway thank you for your help, I could rule out my inability to start the fastboot mode and blame it on the phone xD
Hope I'll be luckier with the next one...
Click to expand...
Click to collapse
No problem, I hope you have more luck with the replacement.
Here I am again, new device, still can't boot to fastboot mode (this time I didn't flash anything, just unlocked bootloader so it's not bricked).
"adb reboot-bootloader" works, advanced reboot menu works, yet the vol+ combination hangs on the vendor's logo.
I'm contacting cyanogen os people to try to understand what might be the issue...
Could you please confirm that your device boots into fastboot mode when using the vol+ way? thank you
maxxie00 said:
Here I am again, new device, still can't boot to fastboot mode (this time I didn't flash anything, just unlocked bootloader so it's not bricked).
"adb reboot-bootloader" works, advanced reboot menu works, yet the vol+ combination hangs on the vendor's logo.
I'm contacting cyanogen os people to try to understand what might be the issue...
Could you please confirm that your device boots into fastboot mode when using the vol+ way? thank you
Click to expand...
Click to collapse
Hello again,
So these 5 methods work for me, someone else may have other experiences:
Phone powered off, hold vol+ while connecting USB, other end of USB already plugged into PC, continue holding vol+ until booted to fastboot (almost instant).
Phone powered on, already connected to USB, other end of USB already plugged into PC, hold vol+ and power until reboot vibrate, continue holding vol+ until booted to fastboot (almost instant).
Phone powered on and in OS, already connected to USB, other end of USB already plugged into PC, debug enabled, from ADB console, adb reboot fastboot or adb reboot bootloader
Phone powered on and in OS, advanced reboot options turned on, hold power, select reboot, select bootloader, reboot
Phone powered on and in Recovery, select reboot to bootloader
Currently I am running stock everything.
Perhaps try different USB cables or ports, though I still get to fastboot without the USB cable plugged in.
My Storm was a pre-order so is one of the first releases, it is possible they have changed something since.
Edit: I have come across a thread on the Cyanogen forums which implies this may be related to encrypting your device: http://forum.cyanogenmod.org/topic/117661-bootloader-hangs/ - I see you have been there already
as reference mine is not encrypted at the moment
Hi guys,
I can not turn on my huawei y625-u21. When i am trying to switch it on, phone freezes on huawei logo (first screen which is shown on start - probably called boot screen). I am not able run also recovery mode (vol+) or update mode (vol+ and vol-), so i am not able to perform update of firmware from sd card. Is there any other way to to perform update (flash) of firmware on device, which is not turned on? I have read something about twrp flash, but if i am not wrong, device should be switched on before this process. I would like to install new firmwere, to check, if phone has hardware or software defect.
to put it into recovery mode, you need to hold volume up button and power button, once the huawei logo appears, release power button but keep holding volume up, after about 30 - 45 seconds, it will boot into recovery mode. i have had this issue over and over and i've had to discover this method myself after trying all methods i found, you can reach me on [email protected] in case you need anything else. if it fails to boot into recovery, just remove the battery for a few seconds and insert then try again. i have this very model of phone too.
Hi everone,
I did a rollback via dload, but messed up an later update. Now I can't get into fastboot mode anymore.
Had a bootloop yesterday and couldn't power down the device, everytime it booted immediately again and stuck with the Huawei logo.
I let the battery drain over night and after that managed to get into fastboot mode once, so I took the chance and opened the bootloader again via fastboot, to be able to flash stock recovery.
But now I am stuck with the "Your device has been unlocked and can't be trusted. Your device is booting now..." screen, and it always boots immediately into that. No chance to get into fastboot/bootloader mode not by pressing Vol- and Power, not by holding down V- and connecting to USB.
ALL I need, is to get into fastboot once more to be able to flash boot-partition.
Any advice highly appreciated.
Thanks, Paco
[SOLVED] Can't get p9lite into fastboot/bootloader mode anymore
pacocalvari said:
Hi everone,
I did a rollback via dload, but messed up an later update. Now I can't get into fastboot mode anymore.
Had a bootloop yesterday and couldn't power down the device, everytime it booted immediately again and stuck with the Huawei logo.
I let the battery drain over night and after that managed to get into fastboot mode once, so I took the chance and opened the bootloader again via fastboot, to be able to flash stock recovery.
But now I am stuck with the "Your device has been unlocked and can't be trusted. Your device is booting now..." screen, and it always boots immediately into that. No chance to get into fastboot/bootloader mode not by pressing Vol- and Power, not by holding down V- and connecting to USB.
ALL I need, is to get into fastboot once more to be able to flash boot-partition.
Any advice highly appreciated.
Thanks, Paco
Click to expand...
Click to collapse
OK, solved. I really had to let the battery drain again completely over night. After that, holding down Vol- and plugging in USB worked to get into fastboot.
I miss the times where you could put out the battery...
Hi all,
The device I have is currently stuck on the Huawei boot screen, and it is unable to turn off as long as the battery has enough charge. Long pressing the power button just reboots the device back to the Huawei screen.
I was able to boot to the erecovery screen, or the HiSuite screen using both Vol+ & power or Vol- & power before. But since last night, I cannot do this anymore. No matter which combination I use, the phone simply reboots to the Huawei screen.
Connecting it to a pc also does not make it listed with either fastboot or adb, so I'm kind of worried that my device is bricked beyond repair.
Do any of you have ideas or advice regarding this situation?
Cheers,
Evert
Connect the cable from your phone to pc , hold the power button and volume down until it show fastboot mode