Hi, I replaced my display and now I have problem with unlocking my phone. Usually after I lock my phone (button or double tap) I can´t unlock right after I did it, I have to wait at least few seconds and try it again. I checked the proximity and light sensor and everything is working. Sometime when I try to unlock the phone, I can see that the display backlight turns on, but that´s all and the display is still black. Does anybody now what can be the problem ?
Thank you
Did you fix it?
My device have similar problems, once you lock the screen it turns impossible to unlock it, only a reset let use tje phone again, but in a laggy way.
Related
After i hang up on a call (when the phone is in sleep mode and the screen is locked) the screen unlocks. this is quite contrary to what is mentioned in the phone manual chapter 1 page 45. this becomes an issue since i use a bluetooth headset and the phone remains in its sleeve/case and after every call, a whole bunch of applications will launch since the case is in contact with the screen. have i overlooked some settings or are there other owners who have faced this issue?
ideas and suggestions welcomed
did you check it out if any of the hardware buttons being pressed against the case hence wakening up the phone.?
i had it to only closed al my apps in taskm and it stoped flickering
My HD2 is also behaving in the same way even in controlled test conditions - the phone unlocks when a call comes in (I'm presented with slide to accept or reject call) The phone unlocks during the call, but fails to lock again on disconnect (either by pressing "end call" or hang up via bluetooth).
Can anyone verify this? Is it interacting with something I installed?
I believe I found a (complicated) workaround.
What I want: leave HD2 inside pocket, answer calls with bluetooth headset, hang up and phone will go back to lock.
Problem: After I hang up using bluetooth or press the big red "End Call" button or the other party hangs up, the phone stays unlocked! It stays powered on and all kinds of buttons gets clicked.
Practically all lock sw uses their own lock screen (which I don't want to install). CSDevCtrl does not trigger by phone. TouchLockPro uses its own transparent lock screen but can respond to phone events. Using the !SUSPEND for TAPI\Ended under settings does not seem to work when the screen dims about 50 secs into the call.
Solution: Use TouchLockPro together with LockAndOff. Get TAPI\Ended to run LockAndOff will turn phone off, whether by bluetooth, big red "End Call" button, or the other party hangs up.
BTW: I think there is some confusion on whether the phone locks when you
1. press the big red "End Call" button, or
2. the hard "End call" button
in the forums.
I noticed that HD2 have a light sensor next to the top ear speaker.
During a call, if the phone is put near the ear and cover the light sensor , the screen become non-active which is good.
If anyone can come up with a lock sceen using this light sensor , then the problem with random launch of program when phone inside pocket will be solved.
This lock screen should only activated right after an end of call, beacuse , sometime you may want to use the phone in a dark place.
linivan said:
I noticed that HD2 have a light sensor next to the top ear speaker.
During a call, if the phone is put near the ear and cover the light sensor , the screen become non-active which is good.
If anyone can come up with a lock sceen using this light sensor , then the problem with random launch of program when phone inside pocket will be solved.
This lock screen should only activated right after an end of call, beacuse , sometime you may want to use the phone in a dark place.
Click to expand...
Click to collapse
It's the proximity sensor that turns the screen on and off during a call, not the light sensor. How else would it work in the dark? (which it does)
johncmolyneux said:
It's the proximity sensor that turns the screen on and off during a call, not the light sensor. How else would it work in the dark? (which it does)
Click to expand...
Click to collapse
My proximity sensor does not work, when I am getting a call my screen turn off and when I am taking the phone out from my face it turn on only when I am out side at the sun!! the screen stay off when I am inside room. I tested it with flsh light and it is working also.
I have a T-Mobile US version of the HD2. I am having the same problem when using the bluetooth system in my car. After answering or making a call the phone stay unlocked. And then starts making random calls while I am driving!!!!
There has got to be an easy fix for this!!!
Buy pocketshield, problem solved.
i have this unlock problem with 1.48 rom and i solve it by pressing start button and lock. after that everything works fine unless i change theme in settings. then just repeat first step.
Solved
Same trouble with me until I use the following software. I tried it and it's almost perfect. unzip it and just copy to your HD2, run CallerLoc.exe and click Yes, you'll find:when you hang up, or he/she hang up a call, or a call is established, the screen will turn off.
Why say 'almost perfect', the software is in chinese, but the filename is in english. and it's a call location software but with the function we need.
To stop or before you delete the software, run Callerloc.exe and click Yes again.
Hope this will help you. Sorry I don't find a English version of this software. I esure and I'm using this software perfectlly with my Leo.
theciscokid said:
Buy pocketshield, problem solved.
Click to expand...
Click to collapse
Same for me
Greetings.
I understand this is quite an old thread I'm digging up but I need a little help as well and I didn't want to start a new topic just for that.
I've this silly problem, appeared right out of the blue:
You all know the standard manila behavior, when the phone is idle, the screen first dims and after some more time, depending on your preferences, the screen locks. It also locks if you press the power off button. This all was happening to me till this morning.
I added an event in the calendar (the only change I made today) and after that, my phone dims and then goes in sleep mode after the designated period of time, but DOESN'T lock!!! It doesn't even lock when I press the power off button. I can still lock it by pressing Start and then lock or by press and hold the power button and choose the lock phone option. So one would say that it's still operational, so why bother about it, but I kinda liked the standard function and I have to freaking idea why it changed!!!
I'd be most appreciative if you could offer some help with that.
Oh, I forgot to mention. Soft reset didn't solve the problem. Erasing the calendar event didn't either.
My phone runs the factory ROM (1.66.482.1 ELL), I haven't changed anything other than user settings (yeah, I'm a noob... )
Thanks in advance!
Nasos
Pocketshield could be the end of your problems. You can try it for 10 days and see how it goes...
But why do I need to buy third party software in order to revert my phone to it's original operation?
No, this is not the answer I am looking for. I was wondering if you know of any kind of settings that might have changed by accident and caused this undesired behavior.
Thanks.
The best to return to normal operation would be a hard reset. Or you can spend a while trying.
You can try
HKLM\Software\Microsoft\Shell\Lockscreen\Enable=1
HKLM\Software\Microsoft\Shell\Lockscreen\Active=1
Thank you very much. I opted for the hard reset option... I hope it stays ok this time!
My HD2 also had some strange unlocking and unwanted calling.
I noticed it appeared when using the android style lockscreen.
When I changed back to the original one, problem solved
i had this too. the andriod lockscreen seems to be a bit buggy last time i used it, i accidentially called 7 random numbers
I've had a problem with my E900 since I got it with regards to the screen. I was hoping Mango might fix it but it doesn't seem to have.
Sometimes if I press the power button the screen backlight comes on (i.e. screen goes from off state to powered) but there is nothing on the screen. No amount of button pressing will cause the screen to show anything.
If this happens I have to turn the device off again (backlight then goes off) and try again. Sometimes it can take 2-3 times before it turns on successfully with the lock screen.
I also have this if an incoming call attempts to wake the phone and also alarms too.
Does anyone else have this issue?
I confirm this one popping sometimes. Not that often that it becomes annoying, but nevertheless.
Did you find a solution to this problem? I am experiencing it too and it is very annoying!
I've recently inherited one as well (E900 that is).
The one I have has been dropped, the backlight powers, but no drawing on the screen.
I've disassembled and re plugged everything (bugger stripping down!) but still no luck. I've done a VolUp+Down+Cam+power hard reset, and when I plug into PC Zune says setup needs completing (so it has reformatted) but still no luck.
I cant see anything fried, and no damaged ribbons as far as I can see, any ideas?
I sold the phone a while ago, and never solved the problem. I think it's a firmware issue.
PaulMdx said:
I've had a problem with my E900 since I got it with regards to the screen. I was hoping Mango might fix it but it doesn't seem to have.
Sometimes if I press the power button the screen backlight comes on (i.e. screen goes from off state to powered) but there is nothing on the screen. No amount of button pressing will cause the screen to show anything.
If this happens I have to turn the device off again (backlight then goes off) and try again. Sometimes it can take 2-3 times before it turns on successfully with the lock screen.
I also have this if an incoming call attempts to wake the phone and also alarms too.
Does anyone else have this issue?
Click to expand...
Click to collapse
hi.
What do you mean "somethimes if I press power button"?
Is it pressed with purpose to lock the phone, press it to turn off phone (background slider shows to power off - on Mango and beyond version) or press it accidentally?
Cheers.
So, I did a phone reset. Unfortunately the issue is still present!
Sometimes when I press the power button to unlock the phone the screen is lit, but stays blank i.e. no lockscreen wallpaper, no nothing. The same happens sometimes when I get a phone call - the phone rings and vibrates, the screen is lit but stays blank.
When this happens I have to press the power button to put the phone into sleep mode and press it again to wake it up.
What I found is, when the issue occurs the screen is actually responsive. For example I can slid up and unlock the phone then I hear the unlock "pop" sound. It's just that nothing is drawn on it!
I was wondering if anyone else experienced the same behavior and found a resolution. Also I am not sure if this is a software or a hardware problem. If I could confirm it was a hardware problem I would call LG and have the phone repaired or replaced.
i have exactly the same issue as you, it gets really annoying.
i heard from someone online that the only way to resolve it is to replace the motherboard
billybrown said:
i have exactly the same issue as you, it gets really annoying.
i heard from someone online that the only way to resolve it is to replace the motherboard
Click to expand...
Click to collapse
I am pretty certain this is a hardware issue. I am calling LG tomorrow and hopefully they'll take the phone for repair/replacement.
I sent my phone for repair. Today I got it back, and guess what?!
The issue is still present! It seems, they "couldn't reproduce" or something.
What should I do now?
EDIT: If anyone is interested, here is a video I just captured which clearly demonstrates the problem. http://youtu.be/38kF9RYs_bU
I'm sending the phone back for repair tomorrow with this video attached.
Hey, might not be an issue at all, but in the video, I saw that the two times you were able to get it to go blank you had your finger on or near the proximity sensor. I wonder if there is something that could be the trigger.
Just wondering if you can duplicated it or cause it only when you have the proximity sensor blocked, or if it truely is random.
You are right, it might has something to do with the proximity/light sensor.
On the other hand, this issue occurs even on incoming calls when the phone is placed on a table, screen up and nothing around the sensor.
Today, I visited my local carrier shop and left the phone for repair again. They told me, since this is a second claim they'll run it through the process faster, so I expect to get it back next week.
Will post an update.
UPDATE: My phone was replaced. Yesterday I got a brand new unit, yeah! It was stock wp 7.0. I plugged in my sim and used the phone the whole day, no sign of blank screen issues. Last nigh I installed all the updates (total 5 I think) up to OS 7.10.8107.79, FW 1.0.16.10. Guess what?! Same issue!
I am crushed
Hey,
i have a problem. after i replaced my LG G2 Display with a new one, it makes problems. when i start to turn on the display, the display turns after 2 seconds off. after 5-6 trys the display works normal. is it a software bug or have i to install the display software? (hard reset)? maybe someone can help me...?
edit: if i try to turn on the display it will switch off after a second. okay. but if i try to turn on the display and press after the power button the volume button up or down it works normaly and no shut down... crazy.. i hope it is only a software bug. and the knock knock feature dosnt work for me. i can lock it with double tap but not unlock it with double tap
bozz59 said:
Hey,
i have a problem. after i replaced my LG G2 Display with a new one, it makes problems. when i start to turn on the display, the display turns after 2 seconds off. after 5-6 trys the display works normal. is it a software bug or have i to install the display software? (hard reset)? maybe someone can help me...?
edit: if i try to turn on the display it will switch off after a second. okay. but if i try to turn on the display and press after the power button the volume button up or down it works normaly and no shut down... crazy.. i hope it is only a software bug. and the knock knock feature dosnt work for me. i can lock it with double tap but not unlock it with double tap
Click to expand...
Click to collapse
It could be associated with kernel. Which ROM and kernel do you have?
Amel.Spahic said:
It could be associated with kernel. Which ROM and kernel do you have?
Click to expand...
Click to collapse
thank you for your answer!
but the problem is another one! Its the proximity sensor!!
the adhesive glue/tape from the new display unit is the main problem. the upper part from the new display unit does not stick properly. so there is a little distance between the display and the frame. and that is the reason why the proximity sensor is not working correctly. and this is the reason why my LG G2 is makin me crazy.
Yo,
yesterday I dropped my GS7E, it wasn't much of a high but the ground was pretty hard. My hardglass screen protector shattered a little but not really much, just the bottom corners of the screen protector got hurt.
Since then, my phone is not waking the screen up the first time I press the power button to unlock the phone. It its waking up but the screen stays black, I can unlock it by fingerprint while the screen is black and even take photos or open any app. I also feel the vibration.
So to fix it and actually get into the phone with screen on I have to lock and unlock it again. If I lock the phone after using it normally, it would work the normal way after unlocking it right again. But if I waited some time and I try unlocking, the screen would just stay black for the first attempt of unlocking.
Isnt that weird? xD
Just wanted to share that and maybe someone even got a permanent fix for that
What happens if you turn it on with the home button instead of the power button?
It wakes up the screen like it would normally do, but the first time I presss it, the screen stays black and I have to lock it again and then I can wake up the screen with home button.
Forgot to mention that.
Probably no solution to that I guess?
If I were u I reflash the firmware. Dont know if that fix it but i would give a try, u got nothing to loose
Hello!
I am new to this forum but I havent found an answer anywhere on the internet. I have a Samsung Galaxy S8 plus with a small crack in the screen in the corner(I dont think its relevant). I have had this phone for almost 2 months.
My problem is: If the phone is locked and I press either the home or lock button, the phone vibrates and it works but the screen will still remain black(lock screen will not be displayed). I know the phone works even when the screen is not working because if I swipe on the black screen, the iris scanner will turn on. I can get it to work but only if I try turning on and off the phone a lot of times until the screen finally turns on. After the screen turns on, I dont have any problems with it(just there are a few lines on the screen from the crack).
Any suggestion might help,
Thanks a lot
well its obviously broken, send it in for repair and pay up bi... man.