VKY-AL00C00 P10, Unable to boot after a magisk 14 update, any long button press combination result in a red led flash and any long power button press result in a vibration and red led flash. Cannot boot into anything!!! Plz help!!!!!!
I have tried the HWOTA method but fastboot is impossible to access, the dload method doesnt seem to work either since there is no reaction from the vol up +down +power combo.
jalk44 said:
VKY-AL00C00 P10, Unable to boot after a magisk 14 update, any long button press combination result in a red led flash and any long power button press result in a vibration and red led flash. Cannot boot into anything!!! Plz help!!!!!!
Click to expand...
Click to collapse
Have you tried booting into erecovery and doing a system restore from there?
_Lithium_ said:
Have you tried booting into erecovery and doing a system restore from there?
Click to expand...
Click to collapse
Yes, but like what i have mentioned , none of the key stroke work at all. All i get are some red led flashes and a vibration with no image showing up at all.
Are you sure that you phone has not just ran outta battery?
_Lithium_ said:
Are you sure that you phone has not just ran outta battery?
Click to expand...
Click to collapse
It was on 70 percent when i charged it first before the magisk update and i have been trying to charge the phone for a while now so i dont think so, but i am not certain as flashing tend to use a lot of battery.
I also flashed several imgs extracted from the official huawei update package beforehand and installed the magisk update in TWRP.
jalk44 said:
I also flashed several imgs extracted from the official huawei update package beforehand and installed the magisk update in TWRP.
Click to expand...
Click to collapse
did you solve it? I have same problem.
some solution
:crying:some solution my huawei p10 plus is dead
Here's my final solution... because the partitioning was destroyed.. i took it back to huawei customer service and because my phone was under warranty, and the fact that they could not verify if the bootloader was unlocked 'since the bootloader software no longer exist on the device' they repaired it under warranty with a free motherboard replacement...
Try the dload method if the keystroke (power button plus volume + and -)works
Geris said:
:crying:some solution my huawei p10 plus is dead
Click to expand...
Click to collapse
ohhh you are not expert i have same last 4 months my huawei p10 plus is dead wait battery drain 0% hold power 1 min then hold vol down + plug USB enter fastboot then if you have BOOT.img RECOVERY.img SYSTEM.img
type fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img
this is worked for me 100%
Gamkutopolowk said:
ohhh you are not expert i have same last 4 months my huawei p10 plus is dead wait battery drain 0% hold power 1 min then hold vol down + plug USB enter fastboot then if you have BOOT.img RECOVERY.img SYSTEM.img
type fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img
this is worked for me 100%
Click to expand...
Click to collapse
Okay, thank you very match, but how will it drain the battery if it does not start?
Geris said:
Okay, thank you very match, but how will it drain the battery if it does not start?
Click to expand...
Click to collapse
if you have battery 0% or if you have not start? try hold vol down + plug USB if work or not ?
Gamkutopolowk said:
if you have battery 0% or if you have not start? try hold vol down + plug USB if work or not ?
Click to expand...
Click to collapse
My English is very poor, please, type a detailed tutorial, this way you can really help man!
When my phone die, battery was on 70%, and I can't do anything, my phone it's completely dead!
---------- Post added at 01:33 AM ---------- Previous post was at 01:29 AM ----------
Geris said:
My English is very poor, please, type a detailed tutorial, this way you can really help man!
When my phone die, battery was on 70%, and I can't do anything, my phone it's completely dead!
Click to expand...
Click to collapse
he flashes a screen quickly, the computer does not show that he connected, he was 70% battery when he died
---------- Post added at 01:50 AM ---------- Previous post was at 01:33 AM ----------
https://youtu.be/AMPtLlMMogM
---------- Post added at 02:01 AM ---------- Previous post was at 01:50 AM ----------
https://www.youtube.com/watch?v=82vH9n604QA
ah your battery 70% because boot or fastboot is freezed still wait battery 0% then try against
Geris said:
My English is very poor, please, type a detailed tutorial, this way you can really help man!
When my phone die, battery was on 70%, and I can't do anything, my phone it's completely dead!
---------- Post added at 01:33 AM ---------- Previous post was at 01:29 AM ----------
he flashes a screen quickly, the computer does not show that he connected, he was 70% battery when he died
---------- Post added at 01:50 AM ---------- Previous post was at 01:33 AM ----------
https://youtu.be/AMPtLlMMogM
---------- Post added at 02:01 AM ---------- Previous post was at 01:50 AM ----------
https://www.youtube.com/watch?v=82vH9n604QA
Click to expand...
Click to collapse
I have same problem,do u resolve this?
Nelix said:
I have same problem,do u resolve this?
Click to expand...
Click to collapse
I could not solve
Just to be clear, none of you actually have the same problem as I did....
So in trying to fix magisk I accidentally flashed a corrupted boot.img and messed up erecovery, which will make it impossible to interact with the phone in any way except to open it up physically. As Partitioning is broken, therefore I took it to huawei repair in China, who did a motherboard for free before asking what roms I used (seriously).
If I was in one of your situations where erecovery is not broken (the thing that's tells u to download and recovery when volume up and power is pressed) in the recovery2 partition on nougat. It would be a matter of simply pressing download and fixing the problem automatically.
Also to be clear my p10 plus has been through hell as I flashed it 20 times that week due to safety net problems so it could have also been that (according to the technician) I simply fried the motherboard.
If this is not what you did or encounter then I repeat YOU ARE NOT HARD BRICKED! and there is a factory provided method for fixing your problems without resorting to flashing.
First: if your bootloader is unlocked, there will be a bootscreen telling you to press vol up to enter erecovery. If you can do that then problem solved, use the download function to repair your phone (it will lock your bootloader showing that I was never unlocked, as well as format data and all other partitions, so your will lose twrp or any custom recovery)
Btw: in oreo the recovery for huawei is located at ramdisk_recovey partition, and the erecovery partition can no longer be written to which in essence makes the china edition of these phones unbrickble as long as u didnt fry anything.
If erecovery doesn't work for you, try routing your wifi through a vpn that changes your ip to China, that will guarantee it to works as well as faster download(hicloud servers are in China).
Idk about the European and international variants but I have done this more the 40 times on my mate 9 pro and p10 plus, the only time I corrupted anything was by flashing images, SO ONLY DO FLASHING AS A LAST Resort.
Related
Hi.
First of all: yes, I'm stupid . Now let's get on with it and solve the problem. If you give me the solution I'll buy you dinner (PayPal). You should also be aware that I'm quite UNfamiliar with expressions and procedures such as flashing, adb, frp, fastboot, etc. Yes, I repeat, I'm stupid . Here is my story:
1. Bought a Huawei Nova in Germany and brought it to Brazil.
2. A few days ago tried a manual upgrade creating a dload folder on the phone and copying a update.app file into it (got it somewhere in this forum).
3. Power + vol up + vol down starts installation that stops at 52%.
4. Power + vol up shows a screen with factory reset and cache clearing options. It only shows very fast, and I'm unable to choose any of them. If by chance the reset option is chosen it does not seem to work. The phone just boots into recovery mode.
5. Power + vol down with the phone NOT connected to a PC leads do recovery mode. It does not recovers anything. It connects to wifi, but also with error msgs at the end.
6. Power + vol down with the phone conncted to a PC leads to Fastboot&Rescue Mode. Below the android image it reads: PHONE Locked, FRP Lock
7. When connected to a PC HiSuite opens, but that's about it.
Guess that's it. Waiting for help.
Correct me if im wrong but,first step you put update app in dload the 3 button flash.....
After flash is done you remove the content of dload then you put the rest of the zip in the dload then re do the 3 button flash for the rest of the update
AGAIN,IM NOT 100% SURE but...
---------- Post added at 06:56 PM ---------- Previous post was at 06:54 PM ----------
look here... and at METHOD 2
http://ministryofsolutions.com/2017...ougat-b300-firmware-update-canada-rogers.html
Partially right
virusdunil said:
Correct me if im wrong but,first step you put update app in dload the 3 button flash.....
After flash is done you remove the content of dload then you put the rest of the zip in the dload then re do the 3 button flash for the rest of the update
AGAIN,IM NOT 100% SURE but...
---------- Post added at 06:56 PM ---------- Previous post was at 06:54 PM ----------
look here... and at METHOD 2
Url removed
Click to expand...
Click to collapse
Your first paragraph is correct. Only the first (sadly). After pressing the 3 buttons....bang....the trouble starts. The process never comes to an end and notning else seems to work.
i can fix it 100% guaranteed , just contact me through personal message
mutahharbashir said:
i can fix it 100% guaranteed , just contact me through personal message
Click to expand...
Click to collapse
Why not sharing the solution here so everyone who would have the same problem could benefit?
#Henkate said:
Why not sharing the solution here so everyone who would have the same problem could benefit?
Click to expand...
Click to collapse
I think everyone knows about dc-phoenix
Sent from my HUAWEI MT7-TL10 using XDA-Developers Legacy app
Not sure they have any functionality for the Nova besides unlocking at this point.
My link got deleted bu...search for ministry of solution on google and youll find what you need
I have successfully unbricked this phone using dc-phoenix,
But lost imei, that i am gonna fix soon
Sent from my HUAWEI MT7-TL10 using XDA-Developers Legacy app
My phone is bricked and I was thinking about flashing it via adb fastboot, but I cant since my bootloader is locked, I tried to get the code but it is asking me for info which I can only get with phone turned on, is there anything I can do?
I got IMEI only, but I also need Product Model, Product Serial number, Product ID. (I can access those only in settings and in dial pad if I am not wrong).
See the back of phone, what type of model is? VNS-???
SPLT said:
See the back of phone, what type of model is? VNS-???
Click to expand...
Click to collapse
VNS-L21 (single sim)
1mbb23 said:
VNS-L21 (single sim)
Click to expand...
Click to collapse
Ok, do you have installed the driver or Hisuite?
1mbb23 said:
My phone is bricked and I was thinking about flashing it via adb fastboot, but I cant since my bootloader is locked, I tried to get the code but it is asking me for info which I can only get with phone turned on, is there anything I can do?
I got IMEI only, but I also need Product Model, Product Serial number, Product ID. (I can access those only in settings and in dial pad if I am not wrong).
Click to expand...
Click to collapse
Reflash stock rom using dload method. It doesn't require an unlocked bootloader.
Here's how to do it: CLICK HERE . Read carefully
I've the same problem now, but I cannot enter ind load mode. my p9 lite not shutdown. if I hold power button it reboot but non load or recovery mode. only fastboot mode. but I haven't enabled developer option so I can't unlock bootloader. how can I do?
---------- Post added at 03:35 PM ---------- Previous post was at 03:34 PM ----------
dariomrk said:
Reflash stock rom using dload method. It doesn't require an unlocked bootloader.
Here's how to do it: CLICK HERE . Read carefully
Click to expand...
Click to collapse
but I hav unlock code for boot loader
croccio said:
i've the same problem now, but i cannot enter ind load mode. My p9 lite not shutdown. If i hold power button it reboot but non load or recovery mode. Only fastboot mode. But i haven't enabled developer option so i can't unlock bootloader. How can i do?
---------- post added at 03:35 pm ---------- previous post was at 03:34 pm ----------
but i hav unlock code for boot loader
Click to expand...
Click to collapse
DID YOU READ THE THREAD I POSTED IN THE LINK ABOVE?!?!?
•No?
•Okay, then read it carefully, BECAUSE I'M NOT HELPING THROUGH PERSONAL MESSAGES!
it cannot enter in dload mode
edit:
if press power off button for 10 sec it restart.
is there any way to turn off it?
---------- Post added at 03:51 PM ---------- Previous post was at 03:49 PM ----------
dariomrk said:
DID YOU READ THE THREAD I POSTED IN THE LINK ABOVE?!?!?
•No?
•Okay, then read it carefully, BECAUSE I'M NOT HELPING THROUGH PERSONAL MESSAGES!
Click to expand...
Click to collapse
yes I've read it, but cannot enter in dload mode with vol - and power. it restart infinite
croccio said:
it cannot enter in dload mode
edit:
if press power off button for 10 sec it restart.
is there any way to turn off it?
Click to expand...
Click to collapse
When your phone restarts press volume + and volume - only!
dariomrk said:
When your phone restarts press volume + and volume - only!
Click to expand...
Click to collapse
I've tried so:
how power off
when screen is black press vol - and vol + and power
boot logo appear and vibrate
than after few sec logo disappear than vibrate and appear logo.
if press only vol+ and vol- it vibrates two times
it stuck with logo
•Hold power button until you feel a vibration
•Immediately press and hold volume +&- untill your phone doesn't start updating from the dload folder on your sdcard
dariomrk said:
When your phone restarts press volume + and volume - only!
Click to expand...
Click to collapse
dariomrk said:
•Hold power button until you feel a vibration
•Immediately press and hold volume +&- untill your phone doesn't start updating from the dload folder on your sdcard
Click to expand...
Click to collapse
it vibrates two times but nothing dload
---------- Post added at 03:57 PM ---------- Previous post was at 03:56 PM ----------
if you want I can make video, maybe I wrong something
croccio said:
it vibrates two times but nothing dload
---------- Post added at 03:57 PM ---------- Previous post was at 03:56 PM ----------
if you want I can make video, maybe I wrong something
Click to expand...
Click to collapse
I can't. Wait for help from someone elsw
dariomrk said:
•Hold power button until you feel a vibration
•Immediately press and hold volume +&- untill your phone doesn't start updating from the dload folder on your sdcard
Click to expand...
Click to collapse
please help me my phone doesn't start at all ... what can i do i have faild flashing it ... is there any hope for me ??
:crying::crying:
Try this: conect the phone to charger or USB, hold power + vol Up and there you will join to erecovery and choose shutdown, if this not appear try without charger.
i have mate 10 lite same problem,bootloader is locked so can i use dload method,and where to get the stock firmware
I have executed these commands and after from this moment, the screen of my device is black and which key or combinations of keys I press nothing works..
Code:
fastboot flash preloader preloader_begonia.bin
fastboot flash lk lk.img
fastboot flash lk2 lk.img
Disconnected the cable, connected the cable, holding the keys for a longer period, holding them for a short period. Only power key, only volume up/down, combining power with volume. Nothing works. When connecting it to the computer, I do see device manager constantly refreshing. But both fastboot and adb are not finding any devices.
When holding the power button for more then 10 seconds, I do feel a small vibe but thats all. Nothing further happens, also not when connecting it to the PC or disconnecting it from the PC.
Anyone any idea what I could to to fix this?
Josjr said:
I have executed these commands and after from this moment, the screen of my device is black and which key or combinations of keys I press nothing works..
Code:
fastboot flash preloader preloader_begonia.bin
fastboot flash lk lk.img
fastboot flash lk2 lk.img
Disconnected the cable, connected the cable, holding the keys for a longer period, holding them for a short period. Only power key, only volume up/down, combining power with volume. Nothing works. When connecting it to the computer, I do see device manager constantly refreshing. But both fastboot and adb are not finding any devices.
When holding the power button for more then 10 seconds, I do feel a small vibe but thats all. Nothing further happens, also not when connecting it to the PC or disconnecting it from the PC.
Anyone any idea what I could to to fix this?
Click to expand...
Click to collapse
Wrong section bro...
-Alf- said:
Wrong section bro...
Click to expand...
Click to collapse
Oh sorry, where should I post this then?
Josjr said:
Oh sorry, where should I post this then?
Click to expand...
Click to collapse
Xiaomi Redmi Note 8 Pro
Hello, I m battling this problem already 2 days, I have P8 Lite mobile phone.
Phone Originally came with ALE-L21 C432B132 but at that time I got update ALE-L21 C432B188 what made my phone 5.0.1 Android
So a few days ago I received Update ALE-L21 C432B587 in updater but what happened is the update stuck on 1 % then showed Error message
That I cant Install that and Phone Rebooted. And it stuck on the First LOGO and now the fun part starts.
I read Every single post, guide what was on google all Suggested to use fastboot and just Flash back to my Original ALE .
Ok, so I did all the Phone Unlocking by getting unlock code and then using fastboot to unlock the phone now my phone is unlocked and it shows that when I'm in fastboot.
I also put UPDATE.app in SDcard just in case but thing is I cant Access that Update menu Or Recovery menu With Button UP + Power Only thing what Works is Fastboot
So I Extracted the boot, System, Recovery, cust, placed in adb folder and run the Cmd if I write fastboot devices it shows my phone so all is ok . and when I do all the flash commands nothings are failing and all shows that is completed. but still I can't start my phone and the only volume down + power works other combinations have no reaction + It just stands on that logo it doesn't even reboot how others have it
I let it send there for 1 h and it was just That first Logo.
So I'm writing here maybe someone has some Suggestion how to Resurrect my phone I'm open now to any suggestions.
Flash TWRP recovery
Then flash any ROM you want by TWRP
You can get the ROMs via "firmware finder" application, it's in play store..
Thank you for your Answer . I Tried to Install TWRP Recovery but without a luck Phone just stays on LOGO and Only button Combination Works is Volume Down + Power what Goes in Fast boot. Maybe i dont know how to enter TWRP mode however non of Huawei button presses worked. Maybe there is other way to get in that Recovery mode .. Also when i turn on phone and im in that LOGO my phone is not recognized by my PC , ONLY if i enter Fastboot i can See my Phone in Device manager and in CMD writing fastboot Devices. if i write adb devices it shows nothing .
also i have question does it mattare how i write : fastboot flash boot boot.img because if i write fastboot flash BOOT boot.img i cant flash it only if all letters are small it goes in .
Ok, so Today I took off the back plastic and disconnected the battery just in case that would help. And no phone still is stuck in the First logo
But there is new thing Happening If I Go from Fastboot to Recovery mode pressing Vol UP + Power wile wire is connected.
So now it shows some sort of Error
Where its mention Func NO: 7 (teeos image) however I straight away tried to flash it and I cant do it it's not Allowed.
Positivity_ said:
Ok, so Today I took off the back plastic and disconnected the battery just in case that would help. And no phone still is stuck in the First logo
But there is new thing Happening If I Go from Fastboot to Recovery mode pressing Vol UP + Power wile wire is connected.
So now it shows some sort of Error
Where its mention Func NO: 7 (teeos image) however I straight away tried to flash it and I cant do it it's not Allowed.
Click to expand...
Click to collapse
run twrp press vol plus and power and diconnect your phone from pc.
Adi5 said:
run twrp press vol plus and power and diconnect your phone from pc.
Click to expand...
Click to collapse
I just flashed TWRP3.0.2.img and Did what you told i got same Error what you can see in image. is that wrong twrp version?
try to put the UPDATE.APP in the dload folder on SDcard and with phone off, press VOLUME UP + VOLUME DOWN + POWER, if recovery2 is not corrupted it should work. Good Luck
redknight65 said:
try to put the UPDATE.APP in the dload folder on SDcard and with phone off, press VOLUME UP + VOLUME DOWN + POWER, it should work
Click to expand...
Click to collapse
I have that in there I have one what is Update.zip and one what is UPDATE.app . all that is happening now is if do that button combination and wait few Seconds phone just Vibrates once and
nothing happens on Screen.
I also tried twrp 2.8.7 just know and Again the same problem what in the Image I uploaded.
Positivity_ said:
I have that in there I have one what is Update.zip and one what is UPDATE.app . all that is happening now is if do that button combination and wait few Seconds phone just Vibrates once and
nothing happens on Screen.
I also tried twrp 2.8.7 just know and Again the same problem what in the Image I uploaded.
Click to expand...
Click to collapse
how long did you wait after the vibration?
---------- Post added at 21:30 ---------- Previous post was at 21:29 ----------
also try to flash recovery2
redknight65 said:
how long did you wait after the vibration?
Click to expand...
Click to collapse
at last 2 min or even more buttons are pressed nothing happens
Yes i flashed Recovery2 too with the ROM i flashed now still the same
I did Steps like in tutorials
Starting with lowest Version then flashing up Still nothing.
Positivity_ said:
at last 2 min or even more buttons are pressed nothing happens
Click to expand...
Click to collapse
try to flash recovery2 and do that again
redknight65 said:
try to flash recovery2 and do that again
Click to expand...
Click to collapse
I just did it again .. nop it still just vibrates and nothing is happening.
Positivity_ said:
I just did it again .. nop it still just vibrates and nothing is happening.
Click to expand...
Click to collapse
then I can't help you, sorry
Positivity_ said:
I just did it again .. nop it still just vibrates and nothing is happening.
Click to expand...
Click to collapse
Download surdu_petru TWRP it is only one for Ale-L21 version 3.1.1.0 flash it by fastboot and then try! I had same problem and this solved it.
RootingPro-18 said:
Download surdu_petru TWRP it is only one for Ale-L21 version 3.1.1.0 flash it by fastboot and then try! I had same problem and this solved it.
Click to expand...
Click to collapse
Thanks for Answer
I just Tried it i used this https://forum.xda-developers.com/p8lite/orig-development/twrp-t3583180
And i still got same Error message what is in image
I Boots in that Image without Any Button press.
And if i Press VolUP + Power its the same
Positivity_ said:
Thanks for Answer
I just Tried it i used this https://forum.xda-developers.com/p8lite/orig-development/twrp-t3583180
And i still got same Error message what is in image
I Boots in that Image without Any Button press.
Click to expand...
Click to collapse
Yeah, system is corrupted, you need B612 firmware if you have dual sim or b611 if you have single sim. Flash Cust boot system, not recovery! This should fix it
---------- Post added at 10:18 PM ---------- Previous post was at 10:16 PM ----------
Positivity_ said:
Thanks for Answer
I just Tried it i used this https://forum.xda-developers.com/p8lite/orig-development/twrp-t3583180
And i still got same Error message what is in image
I Boots in that Image without Any Button press.
And if i Press VolUP + Power its the same
Click to expand...
Click to collapse
Try to shut down your phone and then try. On Fastboot just press volume down and wait till it boot's in e recovery
RootingPro-18 said:
Yeah, system is corrupted, you need B612 firmware if you have dual sim or b611 if you have single sim. Flash Cust boot system, not recovery! This should fix it
---------- Post added at 10:18 PM ---------- Previous post was at 10:16 PM ----------
Try to shut down your phone and then try. On Fastboot just press volume down and wait till it boot's in e recovery
Click to expand...
Click to collapse
Ok thanks i will trie B612 I have Dual sim. and about if press volDown then it goes in Fastboot Mode, I never seen any e Recovery only recovery i know is with VolUp + power but that part is not working for me i still get that error .
UPDATE:
Just Flashed B611 as that was for Dual Sim and no luck it shows the same thing. and Recovery mode is not working and Duble Button press Still just produces Vibration after time.
Positivity_ said:
Ok thanks i will trie B612 I have Dual sim. and about if press volDown then it goes in Fastboot Mode, I never seen any e Recovery only recovery i know is with VolUp + power but that part is not working for me i still get that error .
UPDATE:
Just Flashed B611 as that was for Dual Sim and no luck it shows the same thing. and Recovery mode is not working and Duble Button press Still just produces Vibration after time.
Click to expand...
Click to collapse
Noooo, B611 is for single sim. B612 is for Dual.
RootingPro-18 said:
Noooo, B611 is for single sim. B612 is for Dual.
Click to expand...
Click to collapse
Now im Confused .
All pages i found says B611 is for Dual Sim and B612 is single Sim card here is screen
https://i.imgur.com/gc5mvS2.png
If this is not right can you provide me with download link with right version what worked for you ?
Positivity_ said:
Now im Confused .
All pages i found says B611 is for Dual Sim and B612 is single Sim card here is screen
https://i.imgur.com/gc5mvS2.png
If this is not right can you provide me with download link with right version what worked for you ?
Click to expand...
Click to collapse
https://forum.xda-developers.com/p8lite/general/security-update-ale-l21c432b611-single-t3688441 from here you can get lastest vesions
Hi all!
First, english is not fluent for me, so excuse me for grammatical/temporal mistakes in my words.
It is now 12 days I am with my A1 phone bricked. It's bricked because I try to relock my phone with TWRP installed for making an OTA update.... I shouldn't, I know that now. My phone didn't wanted to boot, only on fastboot mode. But I couldn't flash anything because my bootloader seems to be locked now.
I disable the driver enforcement signature, installed the qualcomm drivers, open my phone and use the tespoints method. And my phone boot and this EDL mode 9008, and miflash tool saw it on COMxx and I was able to flash the fastboot july release. I was so happy! :laugh: But, then, the phone now stay in black screen mode :crying: If I plug an USB cable for charge or on PC, the white led blink 3 times. I tried to push the power button during a few minutes, I tried to push power and volume up, power with volume down, power with volume up and down. I tried to reflash 3 times in miflash, everytimes it's a success flash, but I'm still stuck on that black screen mode. I don't know how to exit or if my phone is dead. I tried several USB port and cable too, that doesn't change anything.
Does anyone have any idea how i can exit this annoying black screen blinking white led mode? Or my phone is definitly dead? I searched but I didn't find a solution that works for my phone.
eljulien said:
Hi all!
First, english is not fluent for me, so excuse me for grammatical/temporal mistakes in my words.
It is now 12 days I am with my A1 phone bricked. It's bricked because I try to relock my phone with TWRP installed for making an OTA update.... I shouldn't, I know that now. My phone didn't wanted to boot, only on fastboot mode. But I couldn't flash anything because my bootloader seems to be locked now.
I disable the driver enforcement signature, installed the qualcomm drivers, open my phone and use the tespoints method. And my phone boot and this EDL mode 9008, and miflash tool saw it on COMxx and I was able to flash the fastboot july release. I was so happy! :laugh: But, then, the phone now stay in black screen mode :crying: If I plug an USB cable for charge or on PC, the white led blink 3 times. I tried to push the power button during a few minutes, I tried to push power and volume up, power with volume down, power with volume up and down. I tried to reflash 3 times in miflash, everytimes it's a success flash, but I'm still stuck on that black screen mode. I don't know how to exit or if my phone is dead. I tried several USB port and cable too, that doesn't change anything.
Does anyone have any idea how i can exit this annoying black screen blinking white led mode? Or my phone is definitly dead? I searched but I didn't find a solution that works for my phone.
Click to expand...
Click to collapse
Push and keep power button until your phone will restart
mar.ur said:
Push and keep power button until your phone will restart
Click to expand...
Click to collapse
I already tried that during 3-4 minutes. How long do I need to push it?
eljulien said:
I already tried that during 3-4 minutes. How long do I need to push it?
Click to expand...
Click to collapse
About 10 s . Try to push volume down and power button together and keep untill restart to fastboot
If doesn't work it can mean that power button has broken when you was opening the phone .
Well, I don't think it's the power button broken because if I plug the phone for charging, the led blink. If I disconnected the phone from charge and push the power button for 10s or more, nothing happen. If I put the phone and charge, start to push the power button then unplug the charge cable with power button still pushing it blinks 3 times after unplugged, then nothing. It's a small difference, but still a little reaction so I don't think the power button is the problem, but I'm not sure of that
eljulien said:
Well, I don't think it's the power button broken because if I plug the phone for charging, the led blink. If I disconnected the phone from charge and push the power button for 10s or more, nothing happen. If I put the phone and charge, start to push the power button then unplug the charge cable with power button still pushing it blinks 3 times after unplugged, then nothing. It's a small difference, but still a little reaction so I don't think the power button is the problem, but I'm not sure of that
Click to expand...
Click to collapse
When you connect phone with pc check what recognize in device manager . You can be in qdlooader 9008 or in diagnostic e900 . Always check what is in device manager after connect phone with pc . You will be know in which state is your phone . I don't know if your phone is in edl mode .
try holding on the power button and volume UP (not down) buttons for 10 secs and it should restart, I got into the same problem as u and that is what fixed it for me
if that doesnt work here is a link to a post with a guy that has the same problem: https://forum.xda-developers.com/mi-a1/help/black-screen-xiaomi-mi-a1-reboot-power-t3728497
If I connect the phone to the computer, it shows nothing. I have to bridge the tespoints to make it appears, and then it appears in Qualcomm HS-USB QDLoader9008 (COM10). And then I can flash with miflash and miflash tells me that it's a success.
I have exactly the same problem. Looking for a solution for weeks now. Tried everything that is on the net but still black screen
daveve said:
I have exactly the same problem. Looking for a solution for weeks now. Tried everything that is on the net but still black screen
Click to expand...
Click to collapse
Sorry to read that but I think our phones are dead honestly. I don't see what to try to make it rise from the shadows of this black screen At least, I learn how to go in EDL mode and never relock bootloader with custom recovery. It's an expensive lesson but...
Thanks to you guys for answering and helping me
what is android virson????
rawnel said:
what is android virson????
Click to expand...
Click to collapse
Android 8.1 july patch was installed via EDL mode with miflash tool.
eljulien said:
Android 8.1 july patch was installed via EDL mode with miflash tool.
Click to expand...
Click to collapse
The same thing happens to you. Could you solve it ??
I was in the same situation until i flashef nougat,.
---------- Post added at 12:35 PM ---------- Previous post was at 12:30 PM ----------
I was in the same situation until i flashed nougat,.
---------- Post added at 12:35 PM ---------- Previous post was at 12:35 PM ----------
I was in the same situation until i flashed nougat,.
ccalixtro said:
I was in the same situation until i flashef nougat,.
---------- Post added at 12:35 PM ---------- Previous post was at 12:30 PM ----------
I was in the same situation until i flashed nougat,.
---------- Post added at 12:35 PM ---------- Previous post was at 12:35 PM ----------
I was in the same situation until i flashed nougat,.
Click to expand...
Click to collapse
Also try to flash to Nougat and the problem is not fixed, the vibration is more intermittent only. Thanks for the input.
Enviado desde mi GT-I9505 mediante Tapatalk
XuFLeS said:
Also try to flash to Nougat and the problem is not fixed, the vibration is more intermittent only. Thanks for the input.
Enviado desde mi GT-I9505 mediante Tapatalk
Click to expand...
Click to collapse
same porblem
I am in z-rom version 4
After installing the eureka kernel in my aw05f ..i rebooted my phone into system....but it won't reboot...the screen become black....now i can't access download or recovery mode...no combination of any keys booting my phone also when i connect the charger the screen still remain black....i think it's hard bricked....help me please ...now i am so afraid . Help me please....
Solved .....?
Thanks to @KineSight for his support
Do the following :
Force reboot your phone (I think Volume Down+Power)
and quickly after that you have to press and hold the volume up to boot into TWRP.
This might take a few tries but you can do it.
Once you're in TWRP Flash Magisk 20.3 (It was placed in your Internal Storage by Eureka Kernel @Chatur27)
Your phone should boot fine. You can flash Magisk 20.4 after this.
KineSight said:
Do the following :
Force reboot your phone (I think Volume Down+Power)
and quickly after that you have to press and hold the volume up to boot into TWRP.
This might take a few tries but you can do it.
Once you're in TWRP Flash Magisk 20.3 (It was placed in your Internal Storage by Eureka Kernel @Chatur27)
Your phone should boot fine. You can flash Magisk 20.4 after this.
Click to expand...
Click to collapse
I tried several times but it won't work....any other suggestion please....
Btw ,,thanks so muck
I also think that my revovery and download mode has gone
shawal_islam said:
I also think that my revovery and download mode has gone
Click to expand...
Click to collapse
Is it not possible to force reboot ?
KineSight said:
Is it not possible to force reboot ?
Click to expand...
Click to collapse
The only thing i can do is try to go into the download mode....but it won't go to the download mode and switch off the device....what you said i tried to do but its actually not happening
Give me your telegram or any id that i can contact to you
shawal_islam said:
The only thing i can do is try to go into the download mode....but it won't go to the download mode and switch off the device....what you said i tried to do but its actually not happening
Click to expand...
Click to collapse
Does force rebooting work or is the phone stuck in a black screen and you cannot do anything ?
---------- Post added at 07:42 AM ---------- Previous post was at 07:39 AM ----------
shawal_islam said:
Give me your telegram or any id that i can contact to you
Click to expand...
Click to collapse
@KineSight
KineSight said:
Does force rebooting work or is the phone stuck in a black screen and you cannot do anything ?
---------- Post added at 07:42 AM ---------- Previous post was at 07:39 AM ----------
@KineSight
Click to expand...
Click to collapse
Force reboot work if i press power+vol down button
To go to download mode
Normal method
1. Turn off phone
2. Hold down both volume keys
3. Plug in computer
Bootlooping
1. Plug in to computer
2. Hold down both volume keys
For a difficult phone
1. Connect usb to computer but not to phone
2. Hold down all 3 keys
3. When it buzzes release power and quickly plug in usb to phone.
It might take a few times to get it right.
If it's REALLY BAD
1. Wait for the battery to completely run down and use normal method.
---------- Post added at 08:41 AM ---------- Previous post was at 08:31 AM ----------
shawal_islam said:
I am in z-rom version 4
After installing the eureka kernel in my aw05f ..i rebooted my phone into system....but it won't reboot...the screen become black....now i can't access download or recovery mode...no combination of any keys booting my phone also when i connect the charger the screen still remain black....i think it's hard bricked....help me please ...now i am so afraid . Help me please
Click to expand...
Click to collapse
I have had this black screen a few times
It took me about 10 tries last time.
Use the difficult method above
---------- Post added at 08:43 AM ---------- Previous post was at 08:41 AM ----------
Eureka 4.3 for A20
Works with Magisk 20.3
Install Magisk uninstaller
Install kernel
Install Magisk 20.3
Reboot
You can install Magisk 20.4 later