I wanted to flash the phone, when you install TWRP that it did not, and now the phone does not include and does not respond to the buttons at to connection to a computer is defined as RELINK HS-USB QDLoader 9008 probably fell off the loader
where to find the boot loader files if anyone can help
thank you in advance
tynot43 said:
I wanted to flash the phone, when you install TWRP that it did not, and now the phone does not include and does not respond to the buttons at to connection to a computer is defined as RELINK HS-USB QDLoader 9008 probably fell off the loader
where to find the boot loader files if anyone can help
thank you in advance
Click to expand...
Click to collapse
This sounds like a hard brick. I remember the USB QDloader message from the 2014 Moto X and that's what it meant. I did it once. The only phone I have ever bricked.
To the OP, what exact commands did you use to flash twrp?
Bricking a phone just from flashing a recovery is highly unlikely.
gpz1100 said:
To the OP, what exact commands did you use to flash twrp?
Bricking a phone just from flashing a recovery is highly unlikely.
Click to expand...
Click to collapse
Hey, I am pretty noob at this, and I bricked a 2014 Moto X because I installed 5.0 via OTA having a custom rom, but with some XDA threads I have tried to bring it back to life: I followed a thread (if you want I give you the link), and when I have to run qflash.exe, it gives me this error: "qflash.exe -com5 -ramload MPRG8960.hex -mbn 33 MSM8960_bootloader_singleimage.bin -v -o
C:\Users\usuario\Desktop\blankflash>qflash.exe -com5 -ramload MPRG8960.hex -mbn
33 MSM8960_bootloader_singleimage.bin -v -o
Motorola qflash Utility version 1.3
COMPORT :COM5
RAMLOADER :MPRG8960.hex
type is 0x21
7 mbn file name MSM8960_bootloader_singleimage.bin type 33
verbose mode on
Motorola qflash dll version 1.6
dmss_software_version_req: received invalid or no response
Failed to send software version request"
Any solution?
Check in device manager to see if the phone is even recognized. I recall seeing a driver for this hs-usb 'device', but don't have any links handy. If all else fails, it may still be recoverable but with a jtag set up. Outside of my expertise. Good luck.
It recognises it, and when I have to blankflash it, it gives me that error I wrote above, "dmss_software_versiom_req: received invalid or no response
Failed to send software version request"
Dead, Unbrick, Debrick F460. Dead/boot security error/boot loop kitkat,lollipop version bootloaders, 9006, 9008 modes
FIRST install lg united mobile drivers, connect mobile with battery to pc, check in device manager com ports if 9006 or 9008 mode.
if you can go into custom recovery mode twrp/cwm, then it easy to fix... u need to flash zip.but your self have to make it right now of same version. here the link tutorial.. http://forum.xda-developers.com/showthread.php?t=2451696 OR try adb or terminal command or u need to make zip file. i lost that link. better try ubuntu method also.
CASE1:
if 9006 or 9008 mode, ROOTED,on lollipop/kitkat/marshmallow before phone dead but rooted, first try debrick sdcard which is simpler, then use ubuntu method. this works only if rooted before phone dead. only root access allows to rewrite files on partition here is the link http://forum.xda-developers.com/showthread.php?t=2582142
CASE2:
only 9008 mode, phone dead on lollipop/kitkat/marshmallow, not rooted, then try debrick image and Ubuntu methods. sucess rate is very low.
Guys!
the sdcard debrick may success. then these files can debrick it.
OUr devices can be fixed. After lot of research i found it. kindly go through the link given below for tutorial and do debrick. You need to try from 140 to 220. hope YOU THANK ME HERE is the Link http://m.blog.naver.com/kangmincraft/220675995736
http://m.blog.naver.com/kangmincraft/220626785379
debrick 140 https://drive.google.com/file/d/0BwKzoXanfz0jMFh1OXJ2QnROUWM/view
debrick 160 https://drive.google.com/file/d/0BwKzoXanfz0jemxYR0VNcnZULXc/view
debrick 180 https://drive.google.com/file/d/0BwKzoXanfz0jb2R4eGIzV1BHeGM/view
debrick 200 https://drive.google.com/file/d/0BwKzoXanfz0jUHBTelc4VzlQT2M/view
debrick 220 https://drive.google.com/file/d/0BwKzoXanfz0jZFBXaFRLMFJVWGc/view
try this, this is my own debrick lollipop: https://drive.google.com/file/d/0B09V79Pt4dCUSjF0ZUhNRWxiQ0k/view?usp=drive_web
Read this post who unbricked his dead mobile http://forum.xda-developers.com/showpost.php?p=66264994&postcount=14
just poweron the device after inserting the sdcard. check few times. try to go download mode.
use google translator if needed.
TIPS
sdcard miniumum 4GB, use old sdcards first. then latest memory cards, try sdcard memory higher than phone memory is advantage. try these 3 types.
debrick140 worked for most of them. try this first if you are on lollipop.
Lollipop bricked roms have higher luck.
after successful unbrick, use poweriso/ultraiso to format sdcard. i used poweriso>tools>cleanusb. then format in your pc.
ATTENTION MARSHMALLOW: IF YOU NO ROOT, NO CUSTOM TWRP, NO DOWNLOAD MODE. THEN THERE IS NO DEBRICK IMAGE YET. NOTHING WORKS. GIVE TO REPAIR RIFF,OCTOPUS BOX. THIS GUY SELLING SOUTION https: //www. facebook.com/ giaiphapandroid/. (remove spaces)IF BOUGHT, SHARE THE LINK HERE . i am not seller,i don't vouch anyone here. just helping so that you help others.
if you have friends in vietnam/korea ask them to search MM debrick and share here. if anyone have solution for MM. kindly share here.
SENIOR XDA: I REQUEST YOU TO CREATE DEBRICK FOR MARSHMALLOW.
THANK ME IF USEFUL....
Credits to Vega_Kangmin.
all copyrights to respective owners. i made simpler type. so if read all and google search, everything you can get in detail.
Reply
Hi. My name is kangmin
And you can call me 'Vega'
At first.
That debrick.img is for G3 Cat.6 (F460 S/K/L.) In korea.
So, it didn't work for international phone
(Like G3 Prime.. Maybe.. Not sure.)
And second. This debrick.img file is for kitcat,lollipop.
It didn't work for mashmellow.
Vega_Kangmin said:
Hi. My name is kangmin
And you can call me 'Vega'
At first.
That debrick.img is for G3 Cat.6 (F460 S/K/L.) In korea.
So, it didn't work for international phone
(Like G3 Prime.. Maybe.. Not sure.)
And second. This debrick.img file is for kitcat,lollipop.
It didn't work for mashmellow.
Click to expand...
Click to collapse
Hello Vega,
yes, we need this for G3 Cat.6 (F460 S/K/L.).
Thank you for your hardwork.
how are you? i have been researched all your blog today and tired translating it to english, but still i cannot understand few words. KINDLY MAKE HERE ENGLISH TUTORIAL PLEASE.
my mobile is boot security error when downgrade from marshmallow to lollipop, 5%, laf error. so i need debrick image for F460S30c_00_1223 marshmallow version. could you please make a debrick image for it?
waiting for your private message reply
Okay. I'll going to write for english
But, i don't have much times because, i have an exam
So, i'll write it as soon as possible..!
Help me Vega
Hi Kathik, I have got a problem with my LG G3 Cat.6 F460k, no download mode, no recovery, no power on, no fastboot , only qualcomm hs-usb qdloader 9008 in windows device manager, tell me, You could please tell me what program I can use to fix this problem, I don’t have the files to use in the boarddiag application, because my g3 uses the APQ8084 chipset for the 805 snapdragon processor. Please brother, help me.
Vega_Kangmin said:
Okay. I'll going to write for english
But, i don't have much times because, i have an exam
So, i'll write it as soon as possible..!
Click to expand...
Click to collapse
Thank you brother!!
Thank you Kathik, I will try this method tomorrow in my Lg G3 F460K, then I will write the results, I have many faith in this!! By the way, thank you too for guide me via whatsapp Kathik, you are a truly hero bro!!!!
:good:
manowar24 said:
Hi Vega, I have got a problem with my LG G3 Cat.6 F460k, no download mode, no recovery, no power on, no fastboot , only qualcomm hs-usb qdloader 9008 in windows device manager, tell me, You could please tell me what program I can use to fix this problem, I don’t have the files to use in the boarddiag application, because my g3 uses the APQ8084 chipset for the 805 snapdragon processor. Please brother, help me.
Click to expand...
Click to collapse
manowar24 said:
Thank you brother, I will try this method tomorrow in my Lg G3 F460K, then I will write the results, I have many faith in this!! By the way, thank you too for guide me via whatsapp, you are a truly hero bro!!!!
:good:
Click to expand...
Click to collapse
Welcome bro. hope you fix and share it here
Vega_Kangmin said:
Okay. I'll going to write for english
But, i don't have much times because, i have an exam
So, i'll write it as soon as possible..!
Click to expand...
Click to collapse
Vega. do we need to press any buttons to go into fast boot mode after mounting sdcard? kindly search Marshmallow debrick and share the link please.
manowar
manowar24 said:
Hi Kathik, I have got a problem with my LG G3 Cat.6 F460k, no download mode, no recovery, no power on, no fastboot , only qualcomm hs-usb qdloader 9008 in windows device manager, tell me, You could please tell me what program I can use to fix this problem, I don’t have the files to use in the boarddiag application, because my g3 uses the APQ8084 chipset for the 805 snapdragon processor. Please brother, help me.
Click to expand...
Click to collapse
hi manowar.
you can solve the problem with using debrick.img files.
go to the link and solve the problem!
Hello Vega and Kathik, I have not done the process yet, I will do it tonight, and then I will inform the results.
I also wanted to thank you for the hard work you are doing in publishing this tutorial and translate it into English, I know you're still working on it, but so far it is understandable and looks promising.
I have some questions to you, to clarify the process that will perform tonight, please, answer me this:
I just have a 32 GB microSD Class 10, does this serve? Or it is too large in capacity? (By the way, my Lg G3 F460K is 32GB of storage and 3GB of RAM, it has Android Lollipop 5.0.1 with HOANG LAM CAT6 1.6 ROM and it was rooted)
When I will do the format to the microSD card, before passing by the win32Disk, what format I give it? ¿FAT32 or NTFS? Or the Win32 software do it for me when it will formated the microSD?
After inserting the microSD prepared, simply press the button on/off on the phone? Or I must do any combination of on/off + vol + or any other?
It is rare to found any solution for this korean model, there are only solutions for the international models, but it seems there is nothing for the Korean model (F460L,S,K). I hope that this work will help many people in this situation and prevent all those who are paying for solving this problem.
Please brothers, answer my questions and I will do the rest. Many thanks!!!
Vega_Kangmin said:
hi manowar.
you can solve the problem with using debrick.img files.
go to the link and solve the problem!
Click to expand...
Click to collapse
I´m in the process but....
Hello brothers, good news, my phone is now in Fastboot mode, I´m working with the ADB and CMD commads, but I have several troubles, please help me in this:
I dont have de file "misc.bin", when I disarmed the original KDZ file (kitkat or lollipop) doesnt appear this file. Do you have it? Please send me or letme download it
I cant erase o create the nexts files with the commads: BackupGPT.bin neither PrimaryGPT.bin, I recibe this message when I tried: "Failed: partition table doesn´t exits"
Brothers please help me on this!! I´m very close to fix my f460 all thanks to you!!
Hello brothers Vega and Kathik, good news, thanks to you I could get my phone back, it is now 100% operational, I would not have been achieved this without your support. However, some things did not go as shown in the tutorial, so I'll detail everything I did with my F460K to help everyone with this problem. Thanks to Kathik an d Vega for the debrick files, they are the key to solve this problem.
I am very happy, now I'll help whoever needs it , as Vega and Kathik helped me!!
THANK YOU TOO TO ALL MEMBERS OF XDA, WHO HELP ME IN SOMEWAY.
:good::good::good::good:
manowar24 said:
Hello brothers Vega and Kathik, good news, thanks to you I could get my phone back, it is now 100% operational, I would not have been achieved this without your support. However, some things did not go as shown in the tutorial, so I'll detail everything I did with my F460K to help everyone with this problem. Thanks to Kathik an d Vega for the debrick files, they are the key to solve this problem.
I am very happy, now I'll help whoever needs it , as Vega and Kathik helped me!!
THANK YOU TOO TO ALL MEMBERS OF XDA, WHO HELP ME IN SOMEWAY.
:good::good::good::good:
Click to expand...
Click to collapse
Welcome! happy to hear from you. share your experience here to help others.
do you wanna upgrade to MM? just follow this link http://forum.xda-developers.com/lg-g3/general/update-downgrade-root-lg-g3-f460-s-k-l-t3353542
How I bring back my G3 F460 from Death
Hello, I'll explain you all how I recovered my LG G3 F460K from death, I must first thank @Kathik and @Vega_Kangmin for their guidance, tutorials and files, without them I would not have been able to recover my phone, the steps are basically as they are explained in Vega_Kangmin´s tutorial:
http://m.blog.naver.com/kangmincraft/220675995736
However, I found some differences that stopped me so I had to read and research in Google to make decisions and to continue with the process.
These are the steps that I follow:
1. Download all programs and files suggested in Vega_Kangmin´s tutorial.
2. I extracted the files from the original KDZ Lollipop (F460K20C_00.kdz) and put it in the folder that I call “ADB”. (My G3 had the Lam Hoang 1.6 Android 5.0.1 Rom and was rooted with debugging enabled).
3. With the Win32Disk Imager I make the first boot image to use in the phone with a microSD card, first I try with the debrick image called “debrick140.img” and the screen did nothing, unanswered. Then with the win32Disk Imager I created the image boot with 160MB and bingo!! It works!!, the screen showed the LG logo and immediately fell in Fastboot mode. Here I tell you my first warning: the only microSD card that I have was a 32GB Class 10, so I used it, then the win32Disk Imager program created in it a new partition table and reduced the 32Gb capacity only to 85MB, so after I had saved my phone, I have to save my microSD card, for that, I used Ubuntu, and one program called “Gparted” I uses it to redefine the partition table. So, beware!!!
4. I opened a CMD´s window in the folder "ADB" (shift + right click, click on "open a command window here"), plugged my phone in the PC (Windows installed the drivers of ADB interface and immediately it recognized) and I wrote my first command to verify that everything was in order:
fastboot devices
If all goes well it should show up this:
List of Devices attached
LGF460XXXXXXX device
Then I proceeded with the ADB commands, but in the tutorial I found some errors in the syntax of the commands and the order they should be done, the correct syntax is:
To remove files the syntax is ok, example: fastboot erase aboot
This is the syntax to flash new files is: fastboot flash aboot aboot.bin
(Don´t forget to change names of the extracted kdz files)
And the order for all the process in the ADB pront is this:
fastboot erase aboot
fastboot flash aboot aboot.bin
fastboot erase boot
fastboot flash boot boot.bin
fastboot erase laf
fastboot flash laf laf.bin
fastboot erase rpm
fastboot flash rpm rpm.bin
fastboot erase recovery
fastboot flash recovery recovery.bin
fastboot erase modem
fastboot flash modem modem.bin
fastboot erase SBL1
fastboot flash SBL1 sbl1.bin
fastboot erase tz
fastboot flash tz tz.bin
fastboot erase sbi
fastboot flash sbi sbi.bin
fastboot reboot
exit
Note: none of these files should be used BackupGPT.bin, PrimaryGPT.bin (if you use it the ADB will return an error saying that these tables do not exist, the file misc.bin neither will use because we do not have it and it isn´t important to revive the G3, this information I got it from here:
"YOU NEED TO EXTRACT 10 FILES FROM TOT (if you use a tot file) (aboot, boot, SBL1, dbi, laf, recovery, modem, misc, rpm, tz) and 9 FILES FROM KDZ (this is our case for the Lg G3) (misc file is not present in KDZ so dont worry it is not important) "
That out of here, please read it:
http://forum.xda-developers.com/android/general/unbrick-lg-model-download-recovery-t3060184 -----> Thanks to @hacklockx
5. After restarting the phone it show up the LG logo (this is a good news), so flash an official ROM with the LG Flash Tool as you already know and enjoy our super phone again.
By the way, in my case, after the process restart with the ADB commands, my phone start normally with all my stuff installed, I lost nothing, as if nothing had ever happened, however, I noticed slow and the camera didn´t work so I flash it with the official rom F460K20C_00.kdz and it was like new. Then I rooted it, installed the TPWR and flash again the Lam Hoang 1.6 ROM with Android 5.0.1, then installed the Xposed and that´s all!!
I hope you serve!!
Greetings from Venezuela :good::good::good:
Guys, I need help. My F460L is bootlooping but I can still access download mode. I tried flashing stock MM with LG Flash Tool but it is still bootlooping, what do I need to do?
Jinyung411 said:
Guys, I need help. My F460L is bootlooping but I can still access download mode. I tried flashing stock MM with LG Flash Tool but it is still bootlooping, what do I need to do?
Click to expand...
Click to collapse
Try these options:
1. Change your battery, try another one, in my case I have two battery, one cause endless bootloop on my G3.
2. Use the "LG Mobile Support Tool", install the program, open it, connect your G3 and see the magic happens :good:
Good luck bro
manowar24 said:
Try these options:
1. Change your battery, try another one, in my case I have two battery, one cause endless bootloop on my G3.
2. Use the "LG Mobile Support Tool", install the program, open it, connect your G3 and see the magic happens :good:
Good luck bro
Click to expand...
Click to collapse
I tried using LG Mobile Support Tool but it does not work either. I'll try the battery, thanks. Will report back.
Jinyung411 said:
I tried using LG Mobile Support Tool but it does not work either. I'll try the battery, thanks. Will report back.
Click to expand...
Click to collapse
check this link. downgrade to Lollipop. follow this link http://forum.xda-developers.com/lg-g3/general/update-downgrade-root-lg-g3-f460-s-k-l-t3353542
THANK ME IF I HELPED YOU. also MUST write feedback
Kathik said:
Dead, Unbrick, Debrick F460. Dead/boot security error/boot loop kitkat,lollipop version bootloaders, 9006, 9008 modes
FIRST install lg united mobile drivers, connect mobile with battery to pc, check in device manager com ports if 9006 or 9008 mode.
if you can go into custom recovery mode twrp/cwm, then it easy to fix... u need to flash zip.but your self have to make it right now of same version. here the link tutorial.. http://forum.xda-developers.com/showthread.php?t=2451696 OR try adb or terminal command or u need to make zip file. i lost that link. better try ubuntu method also.
CASE1:
if 9006 or 9008 mode, ROOTED,on lollipop/kitkat/marshmallow before phone dead but rooted, first try debrick sdcard which is simpler, then use ubuntu method. this works only if rooted before phone dead. only root access allows to rewrite files on partition here is the link http://forum.xda-developers.com/showthread.php?t=2582142
CASE2:
only 9008 mode, phone dead on lollipop/kitkat/marshmallow, not rooted, then try debrick image and Ubuntu methods. sucess rate is very low.
Guys!
the sdcard debrick may success. then these files can debrick it.
OUr devices can be fixed. After lot of research i found it. kindly go through the link given below for tutorial and do debrick. You need to try from 140 to 220. hope YOU THANK ME HERE is the Link http://m.blog.naver.com/kangmincraft/220675995736
http://m.blog.naver.com/kangmincraft/220626785379
debrick 140 https://drive.google.com/file/d/0BwKzoXanfz0jMFh1OXJ2QnROUWM/view
debrick 160 https://drive.google.com/file/d/0BwKzoXanfz0jemxYR0VNcnZULXc/view
debrick 180 https://drive.google.com/file/d/0BwKzoXanfz0jb2R4eGIzV1BHeGM/view
debrick 200 https://drive.google.com/file/d/0BwKzoXanfz0jUHBTelc4VzlQT2M/view
debrick 220 https://drive.google.com/file/d/0BwKzoXanfz0jZFBXaFRLMFJVWGc/view
try this, this is my own debrick lollipop: https://drive.google.com/file/d/0B09V79Pt4dCUSjF0ZUhNRWxiQ0k/view?usp=drive_web
Read this post who unbricked his dead mobile http://forum.xda-developers.com/showpost.php?p=66264994&postcount=14
just poweron the device after inserting the sdcard. check few times. try to go download mode.
use google translator if needed.
TIPS
sdcard miniumum 4GB, use old sdcards first. then latest memory cards, try sdcard memory higher than phone memory is advantage. try these 3 types.
debrick140 worked for most of them. try this first if you are on lollipop.
Lollipop bricked roms have higher luck.
after successful unbrick, use poweriso/ultraiso to format sdcard. i used poweriso>tools>cleanusb. then format in your pc.
ATTENTION MARSHMALLOW: IF YOU NO ROOT, NO CUSTOM TWRP, NO DOWNLOAD MODE. THEN THERE IS NO DEBRICK IMAGE YET. NOTHING WORKS. GIVE TO REPAIR RIFF,OCTOPUS BOX. THIS GUY SELLING SOUTION https: //www. facebook.com/ giaiphapandroid/. (remove spaces)IF BOUGHT, SHARE THE LINK HERE . i am not seller,i don't vouch anyone here. just helping so that you help others.
if you have friends in vietnam/korea ask them to search MM debrick and share here. if anyone have solution for MM. kindly share here.
SENIOR XDA: I REQUEST YOU TO CREATE DEBRICK FOR MARSHMALLOW.
THANK ME IF USEFUL....
Credits to Vega_Kangmin.
all copyrights to respective owners. i made simpler type. so if read all and google search, everything you can get in detail.
Click to expand...
Click to collapse
Hey, will this work on the D851?
If not, how do i create a debrick image for the D851?
Regards Mickey.
mickeyasamoah said:
Hey, will this work on the D851?
If not, how do i create a debrick image for the D851?
Regards Mickey.
Click to expand...
Click to collapse
only these can help you by software by money or assistance. just help. not vouch or i don;t get anything from this. your wish. remove spaces
androidbrick . com
https :// www. facebook .com/ giaiphapandroid
http :// www. vungoc -mobile. com/
if don;t wanna risk. better give to repair jtag/octoplus box which 100% fix this.
Hello everyone!
my problem is the next: I tried install a rom of MIUI but fail in my device, after, I tried to install differents roms but nothing work, just showed me the logo Leeco and no more, no avance from the logo.
But I still had recovery with TWRP and I thinked I can install official rom 26s, It was my error.
Now follow with the same problem but now I not have recovery mode (show me recovery with logo Leeco but it instantly turns off ) and bootloader is block.
My only hope, is QFIL to recover recovery mode o any rom, Does anyone have it or tell me how to create one?..
Please anybody will can help me, I have this problem 3 days ago.
Sorry for my bad english, I am learning.
PS. I tried with post of tora33 but no work
FlashOne2.0\le_zl1_qfil_ufs\prog_ufs_firehose_8996_ddr.elf"
22:00:34: ERROR: function: rx_data:247 Error occurred while reading from COM port
22:00:34: ERROR: function: sahara_main:854 Sahara protocol error
22:00:34: ERROR: function: main:265 Uploading Image using Sahara protocol failed
Download Fail:Sahara Fail:QSaharaServer Failrocess fail
Finish Download
Click to expand...
Click to collapse
Are you sure you got Qualcomm drivers installed and your phone is in 9008 mode? Also try rebooting and re-enter 9008 mode. But the biggest problem that there is no qfil restoration files for x722 if I remember correctly, chances to boot with x720 ones are quite low.
Does your fastboot work volume and power down same time??
Sent from my LEX727 using xda premium
---------- Post added at 11:09 AM ---------- Previous post was at 10:53 AM ----------
worked on the phone i got off amazon. thanks!
[quote name="wpbear" post=71566961]This works on lastest USA update Stock (21s).
Have ADB/Fasboot tools on your computer
Make sure you have enabled the developer tools, turned on USB debugging, and authorized your computer on your device
Put emmc_appsboot.mbn from this zip (Download: x727-5.8.019s_bootloader-unlock.zip) in your adb directory on your PC
Put twrp.img from this zip (Download: TWRP) in your adb directory on your PC
On PC open admin CMD prompt
go into fastboot mode on phone (hold power and VOL -)
on PC type:
fastboot devices
fastboot flash aboot emmc_appsboot.mbn
after flash force reboot using Power button. It will ask for a password, just ignore it and reboot back to fastboot by forcing power down then reboot to fastboot (hold power and VOL -)
on PC type:
fastboot devices
fastboot oem unlock-go
fastboot flash recovery twrp.img
boot into twrp (force power down, then hold POWER and VOL +)
TWRP will boot, choose modify system. Choose wipe - then swipe to factory reset, when that is done - then advacned then format data
In TWRP ensure MTP is enabled. In Windows File Explorer the phone should be visibile. Drag and Drop your new ROM.zip, gapps.zip, SU.zip etc...
In TWRP INSTALL new ROM and other zips; choose wipe/dalvik/cache
If you unlock bootloader push power off until it goes off then put it back into fastboot flash twrp .img them power off again power on when phone vibrate volume down you see stock recovery then twrp.
Reboot System.
DONE![/QUOTE]
Sent from my LEX727 using xda premium
voron00 said:
Are you sure you got Qualcomm drivers installed and your phone is in 9008 mode? Also try rebooting and re-enter 9008 mode. But the biggest problem that there is no qfil restoration files for x722 if I remember correctly, chances to boot with x720 ones are quite low.
Click to expand...
Click to collapse
Yeah, that is the problem, I have the drivers and my computer recognize it, the problem, always show the error sahara.
And flash in fastboot no work because bootloader is block and not let me to do flash of anything.
Someone know how to create a qfil? I am developer and I could try but I not found tutorial how to do and I do not have it clear.
zeckAlexs said:
Yeah, that is the problem, I have the drivers and my computer recognize it, the problem, always show the error sahara.
And flash in fastboot no work because bootloader is block and not let me to do flash of anything.
Someone know how to create a qfil? I am developer and I could try but I not found tutorial how to do and I do not have it clear.
Click to expand...
Click to collapse
Every so often the same questions and the same answers.
You should read more. The X722 subforum is for something.
There is no qfil for X722, and there are no magic solutions of X720 / X727. This is an X722, it is locked and NOTHING of X720 / X727 is going to fix it.
Read this:
https://forum.xda-developers.com/le...velopment--and-mods/try-unbrick-x722-t3686191
Greetings.
How do people keep ending up with bricks? Guess I'll have to find a mod to contact them about stickying a thread about the x722 here about stock 26s. It's a bad idea. Never update your x722 to stock 26s, because your bootloader will get locked when you try to flash TWRP. The only way to get out of 26s is to flash Batyan's 01D ROM (in the x722 Development section here), and then unlock your bootloader and flash TWRP. Flashing TWRP over stock 26s will cause a permanent brick because there's absolutely no QFIL file available for this device. Even in China.
sk8223 said:
How do people keep ending up with bricks? Guess I'll have to find a mod to contact them about stickying a thread about the x722 here about stock 26s. It's a bad idea. Never update your x722 to stock 26s, because your bootloader will get locked. The only way to get out of 26s is to flash Batyan's 01D ROM (in the x722 Development section here), and then unlock your bootloader and flash TWRP. Flashing TWRP over stock 26s will cause a permanent brick because there's absolutely no QFIL file available for this device. Even in China.
Click to expand...
Click to collapse
You know I don't really know how they keep doing it but I seen a lot new ones getting this phone and not really studying how to do this stuff and their not paying attention to what model this have this a solid phone.
Sent from my LEX720 using xda premium
This is true ?
https://dc5.androidfilehost.com/dl/...40/818070582850488404/le_zl1_qfil_ufs_fix.zip
paiktaras said:
This is true ?
https://dc5.androidfilehost.com/dl/...40/818070582850488404/le_zl1_qfil_ufs_fix.zip
Click to expand...
Click to collapse
ZL1 its x720/x727 not x722, it's a fix for ppl thata not work the normal qfil rom.