Disclaimer:
I'm not liable to any demage to your device, including Knox. The information here is as good as I know, there is no guarantee.
(If you like to provide extra information or have a correction, I'll add it to the OP)
>>I'm searching for more full repair firmwares (Containing, PIT, Bootloader, etc. seperated), if anyone could send me the files for I9195 and I9192 etc. i'd upload them too, please help and help others.<<
There are several types of a brick:
Bootloop (usually possible to unbrick)
Stuck at splash screen (a bit harder but still usually possible)
Hardbrick (black screen and nothing works) (there is also a possible solution but it could also mean the end)
Full brick (black screen, nothing works, even the hardbrick method doesn't work. solution could be using a JTAG)
How to unbrick a bootloop and stuck at splash screen brick
Download one of the repair firmwares from here
I9195 Here
Thanks a lot for providing the I9195 files to: @b0g
PIT file:
https://drive.google.com/file/d/0Bx2R0nz6jh17bllKenctWnVsWkE/edit?usp=sharing
Other files:
https://drive.google.com/file/d/0Bx2R0nz6jh17aEVHMHkwLVRjWVE/edit?usp=sharing
###########################################################################################
- Unzip/unrar the files
- Install usb drivers and use the Odin program
- Put the files like the following:
(file names starting with: )
Bootloader (BL) > BOOTLOADER...
PDA (AP) > CODE...
PHONE (CP) > MODEM...
CSC > CSC...
PIT > CSB...
- Make sure your device has enough charge 40% is recommended
- Enter download mode (press volume down + home + power button in the booting process for around 20 seconds)
- connect your device (Odin should say "Added")
- Click start (do NOT disconnect your device or restart your computer in the flashing process, this could make things worse)
- Wait until the phone has fully reset and enter the recovery
- Do a "Factory reset" and "Wipe cache"
- Reboot
- Done
How to unbrick a Hardbricked phone
- Buy a USB-JIG online
- Make sure that the devices battery has charged (even if it doesn't show charging animation)
- Remove your battery
- Plug the USB-JIG inside your phone
- Wait 3 minutes and put the battery back inside
- Wait 40 seconds and the "download mode" screen should appear
- Follow the steps like in the "Bootloop and stuck at splashscreen guide" as above (note: you don't have to enter download mode because using the JIG it should enter it automatically)
Credits:
Me
@b0g
reserved
edited
I9195 mirror at Google drive added
Huge thanks go to @b0g for providing the files for I9195! :good:
hi.
i search a solution repair my s4 mini for hours. tried many ways on this forum and others, but nothing works. so i found this and use the data follow the steps above to ressurrect my phone of bootloop and stuck.
odin flashs correctly i think, but after the reset the phone stucks in "recovery booting..."
i checked autoreboot and re partitition, unchecked f reset time. the odin log says everthing ok:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9195OXABML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> persist.img.ext4
<ID:0/003> persdata.img.ext4
<ID:0/003> NON-HLOS.bin
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Removed!!
what can i do, please help?
skortax said:
hi.
i search a solution repair my s4 mini for hours. tried many ways on this forum and others, but nothing works. so i found this and use the data follow the steps above to ressurrect my phone of bootloop and stuck.
odin flashs correctly i think, but after the reset the phone stucks in "recovery booting..."
i checked autoreboot and re partitition, unchecked f reset time. the odin log says everthing ok:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9195OXABML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> persist.img.ext4
<ID:0/003> persdata.img.ext4
<ID:0/003> NON-HLOS.bin
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Removed!!
what can i do, please help?
Click to expand...
Click to collapse
try flashing twrp recovery and wipe all then (despite external sd)
also try flashing with f reset time enabled...
thanks for the quick help. flashed twrp and it boots in recovery, but full wipe doesnt run, so i wiped manually - unfortunately i get bluescreen and i am again at the beginning.
every method i tried ends with the same result: bluescreen, blackscreen, greenscreen and every other existing screen, in every possible loop or odin stuck during the flash process
i think the problem lies deeper and can only be solved with jtag, if it is not an hardware error. what do you think?
Hi I'm having a similar issue with my i9195 getting stuck on boot screen. I think mine has something todo with the new battery i got for it, as the new one only has 3 pins and the old has 4?
one way i found of being able to boot my phone was to take out the battery plug the charger in then put the battery back in once the green battery icon shows that it is charging hold the power until it vibrates and it should (it does for me) start up, i was also able to get into recovery using the above method by holding the home and volume up as normal.
Thanks for this, I will probably use it in near future.
Please someone has the i9192???
Aronuser said:
....
I9195 Here
Thanks a lot for providing the I9195 files to: @b0g
PIT file:
https://drive.google.com/file/d/0Bx2R0nz6jh17bllKenctWnVsWkE/edit?usp=sharing
Other files:
https://drive.google.com/file/d/0Bx2R0nz6jh17aEVHMHkwLVRjWVE/edit?usp=sharing
###########################################################################################
- Unzip/unrar the files
- Install usb drivers and use the Odin program
- Put the files like the following:
(file names starting with: )
Bootloader (BL) > BOOTLOADER...
PDA (AP) > CODE...
PHONE (CP) > MODEM...
CSC > CSC...
PIT > CSB...
- Make sure your device has enough charge 40% is recommended
- Enter download mode (press volume down + home + power button in the booting process for around 20 seconds)
- connect your device (Odin should say "Added")
- Click start (do NOT disconnect your device or restart your computer in the flashing process, this could make things worse)
- Wait until the phone has fully reset and enter the recovery
- Do a "Factory reset" and "Wipe cache"
- Reboot
- Done
.....
Click to expand...
Click to collapse
hi !
can i use this part for to try to downgrade a KK firmware to JB ???!!!
have to check "re-partition" ???
Loulou-13 said:
hi !
can i use this part for to try to downgrade a KK firmware to JB ???!!!
have to check "re-partition" ???
Click to expand...
Click to collapse
yes check re partition, ah and it's not sure yet if it's possible to downgrade from KK i wanna know myself please tell me the result if you know it
yes ,i think i will try it , but i'm "nervious" with re-partition and pit ! i'm a little afraid ...
i would have prefered an advise to a person"spécialist" who know Samsung very well ...... before testing with this flash .
but i know "re-partition" and Odin (I have already had olds Samsungs )
it's principaly the **** of **** of ****** of HELL "Knox" who scares me ...
The pit here is REALLY the good ???
There are devises who have good(s) method(s) for to downgrade , there are other that it's really impossible ..... but for the S4-mini ,nobody have done expérimenations about ,no tutorials ...etc ...
everybody flash as one file .tar now ...
EDIT !
maybe the master @arco68 can answer to this problem ???!!!
... no idea ?!
Hello, can you please help me? I have problems with random restarting of my i9195 S4 Mini (Vodafone). I tried to flash another official ROM, but this problem remains. When I try flash back original stock ROM (or any other ROM - with root or without root), the results are still same - FAIL message in ODIN after aboot.mbn file.
I tried this guide, but again, everything was ended with fail message (check the attached log).
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9195OXABML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sbl1.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl2.mbn
<ID:0/004> sbl3.mbn
<ID:0/004> aboot.mbn
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Can you please help me and tell me what I can do if I want to put back any stock ROM? I am going crazy with the fail message which shows me in every try. Checked with Odin 3.09, 3.07, 1.83 and still no success.
jerrry said:
Hello, can you please help me? I have problems with random restarting of my i9195 S4 Mini (Vodafone). I tried to flash another official ROM, but this problem remains. When I try flash back original stock ROM (or any other ROM - with root or without root), the results are still same - FAIL message in ODIN after aboot.mbn file.
Can you please help me and tell me what I can do if I want to put back any stock ROM? I am going crazy with the fail message which shows me in every try. Checked with Odin 3.09, 3.07, 1.83 and still no success.
Click to expand...
Click to collapse
Can you tell what is the text in download mode screen? If the last 2 lines say BOOTLOADER SW REV : 2, then you have latest bootloader and IT IS IMPOSSIBLE TO DOWNGRADE.
sasank360 said:
Can you tell what is the text in download mode screen? If the last 2 lines say BOOTLOADER SW REV : 2, then you have latest bootloader and IT IS IMPOSSIBLE TO DOWNGRADE.
Click to expand...
Click to collapse
Thank you for reply. Yes, I have Bootloader AP SWREV: 2. But what can I do if I want to change actual ROM which is flashed in device? I would like to get back original Vodafone ROM (stock), but I can't do anything (flash same ROM which is now in device, flash Vodafone ROM, flash custom ROM).
jerrry said:
Hello, can you please help me? I have problems with random restarting of my i9195 S4 Mini (Vodafone). I tried to flash another official ROM, but this problem remains. When I try flash back original stock ROM (or any other ROM - with root or without root), the results are still same - FAIL message in ODIN after aboot.mbn file.
I tried this guide, but again, everything was ended with fail message (check the attached log).
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9195XXUBML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9195OXABML4_2340422_REV01_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sbl1.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl2.mbn
<ID:0/004> sbl3.mbn
<ID:0/004> aboot.mbn
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Can you please help me and tell me what I can do if I want to put back any stock ROM? I am going crazy with the fail message which shows me in every try. Checked with Odin 3.09, 3.07, 1.83 and still no success.
Click to expand...
Click to collapse
I had the same issue (aboot.mbn failing and finally I managed to fix it by flashing I9195XXUCNE6_I9195OXACNE6_DBT with Odin 3.09. Downloaded the firmware from sammobile (http://www.sammobile.com/firmwares/3/?confirm=31540). Had to wipe data/cache after flashing the ROM. Not the ROM I wanted, but at least now I have a working S4 mini again.
jerrry said:
Thank you for reply. Yes, I have Bootloader AP SWREV: 2. But what can I do if I want to change actual ROM which is flashed in device? I would like to get back original Vodafone ROM (stock), but I can't do anything (flash same ROM which is now in device, flash Vodafone ROM, flash custom ROM).
Click to expand...
Click to collapse
skip the modem file and the bootloader file at flashing and you should be fine
Aronuser said:
skip the modem file and the bootloader file at flashing and you should be fine
Click to expand...
Click to collapse
How can I skip these files? Because in ODIN I am selecting just only one file.
EDIT: I HAVE SOLVED THE ISSUE. I am not sure how but I got into a different download mode and the flash worked. I also used different SM-930A Files and it worked but system status is still custom.
I want to put my phone back to stock after I have installed a custom ROM. I have an AT&T S7. I get this error while flashing the firmware using Odin
----------------------------------------------------------------------------------------------------------
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
------------------------------------------------------------------------------------------------------
On the phone it says the following
"SW REV CHECK FAIL : [system]Fused 3 > Binary 1"
If you could tell me how to flash my phone back to stock without getting this error it would be very much appreciated.
I got the same error a while back. For me, it was because I was using Odin 3.11.1. Once I updated to Odin 3.12.3, the restore went smoothly. Someone correct me if that's not the way to fix this issue, but that is what worked for me.
lukemarcondes said:
I got the same error a while back. For me, it was because I was using Odin 3.11.1. Once I updated to Odin 3.12.3, the restore went smoothly. Someone correct me if that's not the way to fix this issue, but that is what worked for me.
Click to expand...
Click to collapse
I have resolved the issue. I have been trying for almost a month now to fix the phone and I finally did it. The device still says custom although I have flashed the official firmware on. Somehow I got into an alternative download mode that accepted the flash. I have no clue how I got it into the mode but it only said "downloading" and showed nothing in the top right corner. No white text.
ColbyTrip1 said:
I have resolved the issue. I have been trying for almost a month now to fix the phone and I finally did it. The device still says custom although I have flashed the official firmware on. Somehow I got into an alternative download mode that accepted the flash. I have no clue how I got it into the mode but it only said "downloading" and showed nothing in the top right corner. No white text.
Click to expand...
Click to collapse
I see. Glad you were able to fix it!
So I flashed the ATT fimware and now phone runs as an AT&T phone with the model number SM930A instead of a Sprint phone with the model number SM930P. I downloaded the sprint firmware (different versions actually, newer and older) and tried flashing the AP, CP, and CSC in Odin but it always fails.
The reason I did this was because I bought the phone unlocked to work with AT&T but after sending it to Samsung for repairs they apparently locked it back and now I am unable to use it with my network. I thought flashing the AT&T firmware would help but obviously it didn't. I since bought a new phone and now I want to sell the phone in question but I want to reset it to work with sprint.
Any suggestions?
I will post the details from Odin Later.
Here are the results of Odin
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1205)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> FAIL! SHA256 is invalid
<OSM> All threads completed. (succeed 0 / failed 1)
HiVuhltage said:
Here are the results of Odin
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1205)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> FAIL! SHA256 is invalid
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Use the odin from this: https://forum.xda-developers.com/showpost.php?p=67601781&postcount=104. Let me know if it fixes it for you.
YMNDLZ said:
Use the odin from this: https://forum.xda-developers.com/showpost.php?p=67601781&postcount=104. Let me know if it fixes it for you.
Click to expand...
Click to collapse
It failed. Here is what the log said,
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> emmc_appsboot.mbn
<ID:0/004> lksecapp.mbn
<ID:0/004> xbl.elf
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Also on my phone, in download mode I recieved the following in red in the upper left corner:
"SW REV CHECK FAIL : [SYSTE]Fused 3 > BINARY 1"
HiVuhltage said:
Also on my phone, in download mode I recieved the following in red in the upper left corner:
"SW REV CHECK FAIL : [SYSTE]Fused 3 > BINARY 1"
Click to expand...
Click to collapse
I have no clue what to do then, your best bet would be to ask around on the ATT forums as its their firmware you're on.
I ran into the same issue found the correct stock
here is the link I used just put it all together and download and use odin and it worked for me. good luck I have not posted 10 times so the link will be in a later post
---------- Post added at 02:37 AM ---------- Previous post was at 02:33 AM ----------
pdscuba said:
here is the link I used just put it all together and download and use odin and it worked for me. good luck I have not posted 10 times so the link will be in a later post
Click to expand...
Click to collapse
OK so I need to wait 4 min between posts I hope I don't get to annoyed.
I keep getting messages
The message you have entered is too short. Please lengthen your message to at least 2 characters.
To prevent spam to the forums, new users must wait four minutes between posts. Sorry for the inconvenience!
---------- Post added at 02:43 AM ---------- Previous post was at 02:37 AM ----------
YMNDLZ said:
Use the odin from this: https://forum.xda-developers.com/showpost.php?p=67601781&postcount=104. Let me know if it fixes it for you.
Click to expand...
Click to collapse
Just putting in ifo until I can put link for you.
---------- Post added at 02:54 AM ---------- Previous post was at 02:43 AM ----------
YMNDLZ said:
Use the odin from this: https://forum.xda-developers.com/showpost.php?p=67601781&postcount=104. Let me know if it fixes it for you.
Click to expand...
Click to collapse
https://www.androidfilehost.com/?fid=529152257862678448
I tried to Flash my samsung galaxy s7 edge (exynos) with android Oreo UK version from sammobile (SM-G935F) and I think I did something wrong here's what I did:
1-The custom ROM that was installed on the device before the process is supermanROM with root and TWRP as the custom recovery
2-I booted to TWRP and selected wipe and checked all the options (cache,sd card etc) so that I can start flashing fresh and clean
3-after that switched to download mode and connected to my PC
4- started Odin and selected the required files:
For AP: AP_G935FXXU2ERD5_CL13438344_QB17788368_REV00_user_low_ship_meta.tar.md5
For BL: BL_G935FXXU2ERD5_CL13438344_QB17788368_REV00_user_low_ship.tar.md5
for CP: CP_G935FXXU2ERD5_CP9485358_CL13438344_QB17788368_REV00_user_low_ship.tar.md5
For CSC: HOME_CSC_OXA_G935FOXA2ERD5_CL13438344_QB17788368_REV00_user_low_ship.tar.md5
And then clicked start
5- After that It said Pass! and the phone restarted but then I stucked in the boot logo and I can't access anything except download mode (Even recovery mode is wiped).
any Idea what happened and what I can do?
I think the wiping messed it up
some info that might be useful:
Odin version: 3.12.3
the log after flashing:
Code:
<ID:0/005> Added!!
<ID:0/005> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the
cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the
cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the
cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the
cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> skip file list for home binary
<ID:0/004> sboot.bin.lz4
<ID:0/004> param.bin.lz4
<ID:0/004> cm.bin.lz4
<ID:0/004> boot.img.lz4
<ID:0/004> recovery.img.lz4
<ID:0/004> system.img.lz4
<ID:0/004> modem.bin.lz4
<ID:0/004> modem_debug.bin.lz4
<ID:0/004> cache.img.lz4
<ID:0/004> hidden.img.lz4
<ID:0/004> Home Binary Download
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 /
failed 0)
<ID:0/005> Added!!
People, you need to read before flashing, if you want to get Oreo on your phone you need to flash with Odin 3.13
Sent from my SM-G930F using XDA-Developers Legacy app
wegiwegi said:
People, you need to read before flashing, if you want to get Oreo on your phone you need to flash with Odin 3.13
Click to expand...
Click to collapse
I have just checked the Odin website and the latest version is 3.12.3, so what do you mean by sayin 3.13?
really.....
what is this,
https://odindownloader.com/download/odin3-v3-13-1
Sent from my SM-G930F using XDA-Developers Legacy app
---------- Post added at 01:03 AM ---------- Previous post was at 12:52 AM ----------
wegiwegi said:
really.....
what is this,
https://odindownloader.com/download/odin3-v3-13-1
Sent from my SM-G930F using XDA-Developers Legacy app
Click to expand...
Click to collapse
Better try this other link
https://forum.xda-developers.com/attachment.php?attachmentid=4431749
Sent from my SM-G930F using XDA-Developers Legacy app
wegiwegi said:
really.....
what is this,
Click to expand...
Click to collapse
my bad, the weird thing is, when I type Odin in google search the site (odinDownload) show up but the site you mentioned wasn't even in the first page!
Well That actually solved the problem, I reall feel silly now
if the moderator wants to delete this post then please feel free to do so.
next time I will check more before thinkin about posting.
really sorry.
nice it is sorted, enjoy Oreo
Sent from my SM-G930F using XDA-Developers Legacy app
Hi,
i'm trying to help a friend about his phone that got into bootloop.
i asked him if he tried to do something, but he say no.
i didn't ask my fried what android version he has because i'm not sure that he know what is this, but i ask him if this can help.
this the state, it's display the pic/logo and reboot:
http://oi64.tinypic.com/k538s8.jpg
- i tried to flash stock firmware with odin and download every firmware file from here:
https://www.sammobile.com/firmwares/galaxy-s7/SM-G930V/
(yes, downloaded them all!) non of them was working; this whats i see on phone in download mode:
http://oi66.tinypic.com/1z1u2i1.jpg
this is the odin version 3.13 output:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1301)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 5238 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> emmc_appsboot.mbn
<ID:0/004> lksecapp.mbn
<ID:0/004> xbl.elf
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Removed!!
Click to expand...
Click to collapse
- i entered into Maintenance Boot Mode and tried 'factory mode' or any Debug mode or 'safe mode' and nothing, phone just reset and going back to bootloop.
http://oi67.tinypic.com/2lmxf09.jpg
- other thing i tried was to use Verizon Wireless Software Upgrade Assistant software;
looks very promising; phone was detected and firmware was downloaded:
AP_G930VVRS8CRK2_CL14274519_QB20800341_REV02_user_low_ship_MULTI_CERT_meta.tar.md5
BL_G930VVRS8CRK2_CL14274519_QB20800341_REV02_user_low_ship_MULTI_CERT.tar.md5
CP_G930VVRS8CRK2_CP11296771_CL14274519_QB20800341_REV02_user_low_ship_MULTI_CERT.tar.md5
CSC_VZW_G930VVZW8CRK2_CL14274519_QB20800341_REV02_user_low_ship_MULTI_CERT.tar.md5
HOME_CSC_VZW_G930VVZW8CRK2_CL14274519_QB20800341_REV02_user_low_ship_MULTI_CERT.tar.md5
but it didn't flash, it's failed, so i copied the files and tried with odin and it was the same - failed.
- i tried with older versions of odin, but they display "unsupported dev" error on the phone.
- i tried with different cable and computer, one at work and other at home - no luck.
i don't know what else to try, after trying to flash 27 firmwares maybe i missing something?
i stayed up all night for this.
any help will be welcomed.
same issue
i can get the newest firmware to flash with odin 3.14 but same issue. only description difference is it seems to freeze then reboot. i have seen it progress a little further with reboots (over time) all the way to the setup screen then freeze and reboot or freeze altogether. been at this for like a week now. driving me nuts please help!! i think im going to try the s7 edge firmware see what that does.
Same exact issue. Hope someone has a solution.
Just have to say. Know the frustration. I have done the same thing with a dozen firmwares. Not as many as you and can not find the answer. If I do i will let you know.
One thing
So I finally got this file to work and pass G930VVRS9CSB1_G930VVZW9CSB1_VZW in odin 3.13. It's still rebooting though. Argh.