Database Users

[Tutorial]UnbricK Nokia X2

First of all download the zip from following link(remember to remove spaces from URL) and extract the folder X-2 any where on your PC.
http s://w ww.dropbox.com/s/kbdvcefv1vt899e/Unbrick-X2.zip?dl=0
Follow the steps:
1: Turn off the phone.
2: Boot your phone in fastboot mode by pressing volume up+volume down+power keys and holding it for 5 seconds. nokia logo will stuck on the screen and the phone is now in fastboot mode.
3: Connect the phone to PC via usb cable. if fastboot driver is installed you will see nokia device in device manager. if not installed, install it via nokia x-tools.
4: Run nokia X-tools and select option #1 (install drivers for Nokia X2).
5: Wait for drivers installation to finish.
6: Open the folder "Minimal ADB and Fastboot" and run the file "Unbrick.exe".
7: Copy the command "Fastboot -i 0x0421 flash recovery recovery.img" and past in command prompt and press enter.
You flashed CWM susseccfully.
8: Turn off the phone by taking the battery out of phone.
9: Now Copy CWM backup taken from any X2 phone to a memory card and put the card into phone.(if you dont have CWM backup I will upload it latter for U...(can not upload it now due to my limited bandwidth)) .
10: Press volume up+power Keys for 5 seconds and then leave it.
11: Wait for 10 to 15 seconds for your phone to boot into CWM recovery.
12: Restore the backup from sdcard.
13: Reboot your phone.
Good Luck...!:good:

thanx a lot for this guide and and for unbrick kit
but how about uploading it to media fire..cuz drop box is too sslow
and thanx again
---------- Post added at 08:45 PM ---------- Previous post was at 08:04 PM ----------
cwm didnt work and stuck at nokia logo

thebiggboss180 said:
thanx a lot for this guide and and for unbrick kit
but how about uploading it to media fire..cuz drop box is too sslow
and thanx again
---------- Post added at 08:45 PM ---------- Previous post was at 08:04 PM ----------
cwm didnt work and stuck at nokia logo
Click to expand...
Click to collapse
See if your nokia driver is installed correctly.
Can you see your device in device manager while its connected to pc in fastboot mode?
Did you successfully flash the recovery via fastboot command?
How long did you wait for your phone to boot into recovery? sometime it takes a little more time to goto recovery.
if the drivers are installed and recovery is flashed then it must goto recovery. I had tested this method on my own phone and its working fine.

isnail said:
See if your nokia driver is installed correctly.
Can you see your device in device manager while its connected to pc in fastboot mode?
Did you successfully flash the recovery via fastboot command?
How long did you wait for your phone to boot into recovery? sometime it takes a little more time to goto recovery.
if the drivers are installed and recovery is flashed then it must goto recovery. I had tested this method on my own phone and its working fine.
Click to expand...
Click to collapse
i did successfully flashed it by ur methode but it still stuck ..i waited more than 2 min..in ur cwm or the other cwm in the other threde
---------- Post added at 09:50 PM ---------- Previous post was at 09:48 PM ----------
maybe it's made for a spicefic product code ?

pls upload the cwm backup

thebiggboss180 said:
i did successfully flashed it by ur methode but it still stuck ..i waited more than 2 min..in ur cwm or the other cwm in the other threde
---------- Post added at 09:50 PM ---------- Previous post was at 09:48 PM ----------
maybe it's made for a spicefic product code ?
Click to expand...
Click to collapse
Before step 7 try this... "fastboot -i 0x0421 oem unlock" command. Anyone having same problem try this.
---------- Post added 18-11-2014 at 12:06 AM ---------- Previous post was 17-11-2014 at 11:55 PM ----------
Before step 7 try this... "fastboot -i 0x0421 oem unlock" command. Anyone having same problem try this.

X2-CWM-Backup
pepengmanok said:
pls upload the cwm backup
Click to expand...
Click to collapse
htt p://w ww.mediafire.com/download/q5vwm72joanppad/X2-CWM-Backup.zip

work but >>>>>>>>>:crying:
sim card not working
(please contact your service provider or nokia care)
plzz help ....

Abood98 said:
work but >>>>>>>>>:crying:
sim card not working
(please contact your service provider or nokia care)
plzz help ....
Click to expand...
Click to collapse
Flashing through Nokia care suite will solve the problem.

isnail said:
Flashing through Nokia care suite will solve the problem.
Click to expand...
Click to collapse
Method will not work
Must change Imei code

Hey bro i installed TWRP in my phone and it accidentaly deleted all of its software first it used to just stuck in fastboot mode as you described above but now it just opens the TWRP please help how do i go to fast boot mode and install CWM
Also can i install the CWM from TWRP?

Nuke96 said:
Hey bro i installed TWRP in my phone and it accidentaly deleted all of its software first it used to just stuck in fastboot mode as you described above but now it just opens the TWRP please help how do i go to fast boot mode and install CWM
Also can i install the CWM from TWRP?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2668005:good:

my nokia x2 hard bricked ,no response no vibration no nokia logo ,how to unbrick it,i tried with nokia care suite but i am getting sahara protocol error...please help

harish120 said:
my nokia x2 hard bricked ,no response no vibration no nokia logo ,how to unbrick it,i tried with nokia care suite but i am getting sahara protocol error...please help
Click to expand...
Click to collapse
Chang driver to (Nokia Flash Connectivity)
driver::http://forum.xda-developers.com/attachment.php?attachmentid=3244023&d=1428123340
Then try With Nokia care suite
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

@Abood98
i already installed that driver ,i even tried to install the driver which you given again but it shows that it is already installed,in my device manager it is showing like this ,not as nokia flash connectivity,instead it shows as nokia emergency connectivity

my x2 bricked, detect as Qualcum........ plz help... how to unbrick without JTAG

Not working my phone is dead he is not responding
How can I go in fastboot

HELP , Bricked my Phone

I was trying to update to Nougat . Flashed the update.zip file and another update_full_cn file. I did the mistake of flashing my regional cust file without booting first..
This is what I get when I try to flash system.img or cust from the stock B380 ROM.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I can flash twrp but can't boot into it. One stupidious thing I did was I rebooted my phone when the dload update showed up but it was stuck at 5%.
EDIT:I fastbooted the boot,system,cust and recovery from the B523 firmware but now it's stuck at Huawei logo.

Go to erecovery and factory reset.
Volume up + power.

Tried it. There's no factory reset option in erecovery.

Astra1 said:
Tried it. There's no factory reset option.
Click to expand...
Click to collapse
How there is no factory reset in stock recovery?

gm007 said:
How there is no factory reset in stock recovery?
Click to expand...
Click to collapse
I don't know. It Just has Download Recovery, reboot and shutdown option.

Astra1 said:
I don't know. It Just has Download Recovery, reboot and shutdown option.
Click to expand...
Click to collapse
Flash stock recovery with fastboot

gm007 said:
Flash stock recovery with fastboot
Click to expand...
Click to collapse
Already did. Same thing.

Astra1 said:
Already did. Same thing.
Click to expand...
Click to collapse
Which version are you using? Latest for C185 is B200 try with this one.

I tried with nougat version and the B386 recovery.

Astra1 said:
I tried with nougat version and the B386 recovery.
Click to expand...
Click to collapse
I think emui 5 have different recovery than emui 4 that's why u have to try B200

gm007 said:
I think emui 5 have different recovery than emui 4 that's why u have to try B200
Click to expand...
Click to collapse
If you have the B200 ROM on your computer can u extract and post the recovery image here.

Astra1 said:
If you have the B200 ROM on your computer can u extract and post the recovery image here.
Click to expand...
Click to collapse
I will in 15 minutes.
---------- Post added at 09:54 AM ---------- Previous post was at 09:38 AM ----------
here you go C185B200 recovery image https://www.mediafire.com/?j62d2vdjhoin1cv

erecovery is recovery2.img file.

grofock said:
erecovery is recovery2.img file.
Click to expand...
Click to collapse
Why do we have 2 recovery in each firmware?
And how to flash the second recovery with fastboot?

To enter TWRP unplug your phone, press Vol UP and then Power, wait til it vibrated 2x , then when you see the huawei logo, release both and wait

Swissguy36 said:
To enter TWRP unplug your phone, press Vol UP and then Power, wait til it vibrated 2x , then when you see the huawei logo, release both and wait
Click to expand...
Click to collapse
First of all, thanks for your reply.
I tried what you told and the stock recovery comes up with the software install failed thing. No matter , How many times I flash twrp, the stock recovery comes up. I tried placing the B380 UPDATE.APP in the dload folder of the sdcard. Tried the same thing with nougat UPDATE.APP. Both times it says software install failed.
Did factory reset again and ahter the message your device is booting, the screen goes blank but stays on.
@gm007, I tried the stock recovery you posted but same result. How come I don't have factory reset? Does it has something to do with being unlocked.
EDITkay, by luck or something I got the WIPE data and cache option. I did both of them, But now it's stuck at your device is booting now.

If you were in EMUI 5.0, welcome to the club, until today I could not revert to 4.1 or 4.0, all I could do was make 5.0 usable. If so, you will have to use the boot, recovery, recovery2 and emui 5.0 system on the fastboot and then use the dload with the rom that "attached" your phone. I'm on AL10C17B523 and I can not reverse it at all, I've already accepted my burden.

Marcelo AF said:
If you were in EMUI 5.0, welcome to the club, until today I could not revert to 4.1 or 4.0, all I could do was make 5.0 usable. If so, you will have to use the boot, recovery, recovery2 and emui 5.0 system on the fastboot and then use the dload with the rom that "attached" your phone. I'm on AL10C17B523 and I can not reverse it at all, I've already accepted my burden.
Click to expand...
Click to collapse
If TWRP for EMUI 5 arrives then we can do something.
So is there something I can do? I copied the UPDATE.APP file of B552 firmware into the dload folder of the sd card and Did the dload update thing. It says incompatible software - installation failed. I think I can fix this, Just need some instructions.

I successfully downgraded to Kangvip b368. The procedure was as follows
First of all make sure you have nougat stock recovery .
Then download stock B320 , extract the update.app and put in the dload folder on the sd card.
Next do the dload update by pressing the 3 buttons.
Hopefully it will complete to 100%
After that do a factory reset. U may find that your bootloader is locked again. So unlock it, flash twrp and u r good to go. Flash Kangvip b368 through twrp and that's it.
Kindly Mark this thread as solved.

Wah astra1

P10 black screen bricked!!

I tried to flash a custom rom (MorfuZ) and after installation is complete, the phone reboot and stucked on black screen. I can't get to fastbook or recovery screen. The MultiTool software recognises the device. I tried flashing trough the ''Unbrick'' method and it seems the process is completed, but the phone won't boot. I tried to turn it up but even the screen is not turned on. I have no red or green led as the others threads says (yes I've read a lot of them). The only sign of life is that my PC detects it as "Fastboot2.0" and it's supposed that I flash cust, boot, system and recovery imgs but nothing happens at all. It sounds it's rebooting and the cmd also says that but there is no change. My phone is LATAM version (WAS-LX3). Already bootloader unlocked, installed TWRP and rooted (magisk). My laptop recognises the device the (prompts sounds when connected.)
I tried flashing boot, recovery, system from this .zip file Warsaw-L23_C605B172_Firmware_Panama_Bolivia_Peru_Chile_Colombia_Guatemala_El Salvador_Nicaragua_Honduras_Nonspecific_Android7.0_EMUI5.1_0501 but I couldn't find the CUST file to flash with Multitool software.
This is what I get after flash using MultiTool
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Plaseas Help !!!

jics91 said:
I tried to flash a custom rom (MorfuZ) and after installation is complete, the phone reboot and stucked on black screen. I can't get to fastbook or recovery screen. The MultiTool software recognises the device. I tried flashing trough the ''Unbrick'' method and it seems the process is completed, but the phone won't boot. I tried to turn it up but even the screen is not turned on. I have no red or green led as the others threads says (yes I've read a lot of them). The only sign of life is that my PC detects it as "Fastboot2.0" and it's supposed that I flash cust, boot, system and recovery imgs but nothing happens at all. It sounds it's rebooting and the cmd also says that but there is no change. My phone is LATAM version (WAS-LX3). Already bootloader unlocked, installed TWRP and rooted (magisk). My laptop recognises the device the (prompts sounds when connected.)
I tried flashing boot, recovery, system from this .zip file Warsaw-L23_C605B172_Firmware_Panama_Bolivia_Peru_Chile_Colombia_Guatemala_El Salvador_Nicaragua_Honduras_Nonspecific_Android7.0_EMUI5.1_0501 but I couldn't find the CUST file to flash with Multitool software.
This is what I get after flash using MultiTool
Plaseas Help !!!
Click to expand...
Click to collapse
If You still have TWRP and if you are on Emui 8 use HWOTA8 method, otherwise if you are on Emui 5 use HWOTA7 to flash your build. As you have already unlocked bootloader the first step in script will be automatically skipped.
Its very easy just follow my video tutorial. Instruction for HWOTA7 is on Serbian but you have instruction on English and some things are logical just view video.
https://forum.xda-developers.com/p10-lite/development/hwota-huawei-p10-lite-t3776186
Good luck!

Thanksfor the reply. My phone won't boot to recovery nor fastboot mode. I can't turn it on or off, the screen does not display anything, it just sounds when I plug it to the pc. No led light or boot logo

jics91 said:
Thanksfor the reply. My phone won't boot to recovery nor fastboot mode. I can't turn it on or off, the screen does not display anything, it just sounds when I plug it to the pc. No led light or boot logo
Click to expand...
Click to collapse
Yes I understand u must use DC phoenix and test point method after that Hcu client to restore Imei, seriall. Dc phoenix and Hcu client are about 20 usd credit for 3 days. But for test point u must open the cover and on board find test point, conect it, plug usb and run Dc phoenix to restore all partitions. Its not so easy but phone could be fixed.
Poslato sa WAS-LX1 uz pomoć Tapatoka

do u have the location of testpoint of this phone

abcrino50 said:
do u have the location of testpoint of this phone
Click to expand...
Click to collapse
Here it is
Sent from my WAS-LX1 using Tapatalk

it dosent work

p10 lite
Alexxxx1 said:
Here it isView attachment 4533946
Sent from my WAS-LX1 using Tapatalk
Click to expand...
Click to collapse
Alexx da li možeš da uradiš p10 lite bricked u Beogradu da ti nekako dostavim i koliko bi koštalo. Pozdrav >Milan

Axon 7 not able to install TWRP or lock bootloader

Hello all,
I need help with my Axon 7 (A2017G)
I upgraded my phone to Oreo 8.1 (AospExtended), played with it a bit, but decided to downgrade to 7.1.1 (stock) again.
After I did so, I noticed something different. Firstly when it boots up, this screen appears
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
It goes away after 5 seconds and boots or if I click the vol up or down button, it takes me to this screen
If I choose anything other than Recovery, the phone just boots up
If I choose Recovery, it takes me here
I cannot boot into recovery mode at all. I can't find out how to install TWRP recovery on here at all.
Also If i boot using power+vol down, this appears
Please advise how to install TWRP and lock the bootloader

Have you tried the Axon 7 tool by Djkuz?
It should be able to get you out of this, I'll find the link for you.

Khepralife said:
Hello all,
I need help with my Axon 7 (A2017G)
I upgraded my phone to Oreo 8.1 (AospExtended), played with it a bit, but decided to downgrade to 7.1.1 (stock) again.
After I did so, I noticed something different. Firstly when it boots up, this screen appears It goes away after 5 seconds and boots or if I click the vol up or down button, it takes me to this screen
If I choose anything other than Recovery, the phone just boots up
If I choose Recovery, it takes me here
I cannot boot into recovery mode at all. I can't find out how to install TWRP recovery on here at all.
Also If i boot using power+vol down, this appears
Please advise how to install TWRP and lock the bootloader
Click to expand...
Click to collapse
that is, like, 100% normal. you have stock recovery and that FTM mode just gives you adb. If you can't enter fastboot then you would have to install it via EDL.
But before doing that, why the heck would you want to lock the bootloader? Lol you can just hide the 5 sec screen and sell it (or return to zte, they never check), there's no difference at all
If you're gonna lock anyways, you have to install TWRP via EDL (use EDL Tool by djkuz) then install the "remove inscription" by raystef66 or follow the steps on his guide. Then you will get fastboot. After you do that, just reboot the phone. TWRP should be replaced with stock recovery again. Check if it was (power + vol+) and if you enter stock recovery then go to Fastboot (via "adb reboot bootloader") and do the command to lock
Of course you have to be FULLY stock (no magisk or whatever) or you'll brick your device

Axon 7 tool
https://forum.xda-developers.com/axon-7/development/axon-7-edl-tool-flash-backup-restore-t3750759
There is an Axon 7 tool kit as well via another post here.
https://forum.xda-developers.com/axon-7/development/tool-axon7toolkit-t3573108

Syberclone said:
Have you tried the Axon 7 tool by Djkuz?
It should be able to get you out of this, I'll find the link for you.
Click to expand...
Click to collapse
Thank you

Choose an username... said:
that is, like, 100% normal. you have stock recovery and that FTM mode just gives you adb. If you can't enter fastboot then you would have to install it via EDL.
But before doing that, why the heck would you want to lock the bootloader? Lol you can just hide the 5 sec screen and sell it (or return to zte, they never check), there's no difference at all
If you're gonna lock anyways, you have to install TWRP via EDL (use EDL Tool by djkuz) then install the "remove inscription" by raystef66 or follow the steps on his guide. Then you will get fastboot. After you do that, just reboot the phone. TWRP should be replaced with stock recovery again. Check if it was (power + vol+) and if you enter stock recovery then go to Fastboot (via "adb reboot bootloader") and do the command to lock
Of course you have to be FULLY stock (no magisk or whatever) or you'll brick your device
Click to expand...
Click to collapse
Thank you

Mi A1 Bootloop after ota update and Locked Bootloader

Hi,
I've installed an ota update and the device didn't boot... it is stuck in a bootloop....
When i try to flash via fastboot, it appears an error saying that the device is locked ant cennot erase...
via fastboot oem unlock i get the error message: Remote: oem unlock is not allowed
via MiUnlocker the unlock gets to de 50% and gives an error and on its logs it says: Remote: oem unlock is not allowed
I tryed to flash TWRP with command fastboot flash recovery but the error is the same: remote: partition flashing is not allowed
Can anyone help me please??
I'm stuck on the bootloop i can't go to setting - developer - allow oem unlock option!!

Have you tried doing a Factory Reset from stock recovery?

This is a strange behavior, even if an OTA update corrupted the system for some reason, the phone should boot from the original slot.
Have you tried switching slots manually from fastboot ?

Parnas72 said:
This is a strange behavior, even if an OTA update corrupted the system for some reason, the phone should boot from the original slot.
Have you tried switching slots manually from fastboot ?
Click to expand...
Click to collapse
How can i do that?

Hello!
I've faced the exact same problem yesterday.
You need to force the phone to boot in EDL mode by opening the back cover and short circuit 2 pins as shown in THIS video.
After you have the phone in EDL and being detected by your PC (you need the correct drivers, you may get them on THIS thread by @CosmicDan), you may use MiFlash Tool to flash official PIE Rom, access developer options and enable oem unlock to be able to unlock your phone again.
If you wish to revert to Oreo, please use THIS guide.
Cheers!

Tepig said:
Have you tried doing a Factory Reset from stock recovery?
Click to expand...
Click to collapse
No recovery.. i get this:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Typhus_ said:
Hello!
I've faced the exact same problem yesterday.
You need to force the phone to boot in EDL mode by opening the back cover and short circuit 2 pins as shown in THIS video.
After you have the phone in EDL and being detected by your PC (you need the correct drivers, you may get them on THIS thread by @CosmicDan), you may use MiFlash Tool to flash official PIE Rom, access developer options and enable oem unlock to be able to unlock your phone again.
If you wish to revert to Oreo, please use THIS guide.
Cheers!
Click to expand...
Click to collapse
Obrigado!
I'll try it now!!

xistolas said:
No recovery.. i get this:
Click to expand...
Click to collapse
Actually you have a recovery. You need to long press the power button and, afterwards (not at the same time), press the volume + button. You'll see that all options will appear.

xistolas said:
How can i do that?
Click to expand...
Click to collapse
fastboot getvar current-slot
to show the current slot,
fastboot --set_active=a or fastboot --set_active=b
to change it.

xistolas said:
Obrigado!
I'll try it now!!
Click to expand...
Click to collapse
get into fastboot mode
hot boot twrp using fastboot command
copy efs backup to twrp backup folder and restore
then go into bootloader mode
flash the firmware using miflash
---------- Post added at 09:27 PM ---------- Previous post was at 09:23 PM ----------
akashavel said:
get into fastboot mode
hot boot twrp using fastboot command
copy efs backup to twrp backup folder and restore
then go into bootloader mode
flash the firmware using miflash
Click to expand...
Click to collapse
follow from step 6 to end in below link
https://forum.xda-developers.com/mi-a1/how-to/tutorial-downgrade-9-0-to-8-1-edl-imei-t3879624