Related
status: Bricked
Access: No fastboot, No recovery However goes automatically to edl once connected to pc
Device manager recognizes as "Qualcomm HS-USB Qloader 9008 [port x] (x whichever usb port I connect)
all drivers installed.
Attempts:
1)Tried flashing via QFIL which gives an error "Download failed: Sahara fail: QsaharaServer fail: Process failed"
2)MIFlash
I have a laptop windows 10 with only 2 usb ports. As soon as I connect the device using usb cable, device manager shows under LPT/com ports as "Qualcomm HS-USB Qloader 9008 (port 5). Then I opened mi flash (also tried miflash beta), selected a fastboot image folder (extracted from tgz), select flash all, my then press refresh option, the tool will detect the phone as port -com 5 and then I clicked on flash. It'll send some signal to phone for 5 sec, and then stops giving error "cannot read from port com 5". I also tried it with other usb port (detects as port com 4).
please somebody help!
Edit: Used MI flash with Windows 7 compatibility mode. Worked like charm...
Use EDL cable, I just fixed it last week. It stuck at 900E not 9008. No fastboot, no recovery, Sahara failed
lintongprohacks said:
Hold down vol down+power to enter fastboot. Upgrade pc to win 10 to avoid issues as win 10 allows unsigned drivers with prompt
Click to expand...
Click to collapse
Read op. It's not possible to go to fastboot nor recovery. Phone just doesn't respond to anything.
arceuss said:
Read op. It's not possible to go to fastboot nor recovery. Phone just doesn't respond to anything.
Click to expand...
Click to collapse
Makes EDL cable by your self. Just take new cable data. Open the skin and sort green cable with black cable. Thats it.
Plug your phone with edl cable for about 3 second. Then open qfil. Setup qfil properly. Do not press download button yet.
But change your edl cable with normal data able.
Put the normal cable ( not edl cable) into your charging port of your phone.
Then plug in into usb port. As soon as you see Qualcomm 9008 port on Qfil press download button.
Qfil fails because waiting too long to press download button. Just press it immedietly after the qfil recognized the port.
If at the first try fail, repeat the prosses once again.
I now always flashing with qfil never use miui flash tool again..
https://forum.xda-developers.com/redmi-3/help/redmi-3s-hardbrick-t3650498
Charge%? Open if it is described in the subject
use TEST POINT
Thanks it worked for me
Thanks it worked for me
charge it for 12 hours +
Keep it for charging for 12 hours and then start i had such problems earlier.. or remove battery and charge the battery separately... the battery is been drained completely i suppose.
This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!
I think someone has made this guide already.
I see.
well i have a similar issue that i am stuck at 9008 port that is edl but, i can flash rom via Qfil and Mi Flash toll but i cant boot onto it=
I cant get out of edl mode lol. stuck at it.
I deleted some files from qpst rom for intentionally hard bricking my phone and heres another fix.
Cut the outer plastic and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
Happy Flashing!
AstroBiswas said:
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994 - not last edition, latest is v1.0.8
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270 - not last edition, latest is 2.7.460 (fix "sahara" error)
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download - not needed
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790 - not needed (if you use the previous paragraph).
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
Click to expand...
Click to collapse
@AstroBiswas Read red comment.
Not_James_Bond said:
I think someone has made this guide already.
Click to expand...
Click to collapse
Of course!
https://forum.xda-developers.com/le...-to-recover-hard-bricked-zuk-z2-plus-t3576007
Not even coming up as 900E
AstroBiswas said:
This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!
Click to expand...
Click to collapse
My hard brick z2 is not even coming up as 900E. Basically computer doesn't detect and no changes in device manager either. Please confirm what to do.
I have tried pressing buttons told by many others and in various other forums. It doesn't work. Does deep flash cable method work even if the phone is not detecting in 900E mode?
You have to boot in proper edl mode...for edl mode hold volume up button 15 second and immediately click power button for .5 sec and attach data cable to phone which is connected to pc and & immediately prees again power button. all while procees alway hold volume up button....
Zuk Z2 Pro Stuck in EDL HS-USB 9008 Port and automatically connecting and disconnect
Hi,
My Zuk Z2 Pro is stuck in EDL 9008 Port. Phone is totally bricked and no sound, no light, no vibration. When i connect with the computer, phone is connecting on HS USB 9008 port and get disconnected after 20-22 seconds and again automatically connected with in half second time.
I am facing this issue after flashing a ZUI 1.9 by using a QPAST/QFIL application. I think i have made stupid mistake by flashing a phone with "ERASE ALL BEFORE DOWNLOAD" option.
I have tried every scenario to get stable this 9008 port but no luck. Since last 5 days i am studying forums and applying every kind of solution but same result.
I am writing this post with high expectations and hope someone will take notice and help me to get rid of this problem.
I can pay through paypal if someone wants to provide professional services to resolve this matter
I will appreciate if someone have any idea and can help me. Thanks
Can someine please help me with this weird situation? Device got disconnected while flashing via qfil. Now no zuk logo nothing. Phone vibrates every 30 sec that's it. Wont even gets recognized by my laptop(no 9008 or 900e port!)
SilenT__ShadoW said:
Can someine please help me with this weird situation? Device got disconnected while flashing via qfil. Now no zuk logo nothing. Phone vibrates every 30 sec that's it. Wont even gets recognized by my laptop(no 9008 or 900e port!)
Click to expand...
Click to collapse
You need to use the deep flash guide which involved cutting and sorting the cable , procedure given in last part of OP
AstroBiswas said:
You need to use the deep flash guide which involved cutting and sorting the cable , procedure given in last part of OP
Click to expand...
Click to collapse
I've tired that also. Connecting phone to pc while green and black wires attached together and detaching them after 5 sec. That also did nothing. However i connect my phone to my pc it just vibrates and blinks led every 30 sec till i remove battery!
SilenT__ShadoW said:
I've tired that also. Connecting phone to pc while green and black wires attached together and detaching them after 5 sec. That also did nothing. However i connect my phone to my pc it just vibrates and blinks led every 30 sec till i remove battery!
Click to expand...
Click to collapse
You need to completely poweoff the phone (difficult in hard brick actually) before this procedure i have forgotten the way to do it, was given on zuk.eu i think, dont worry it may take time but these days hard bricks is repairable too.
AstroBiswas said:
You need to completely poweoff the phone (difficult in hard brick actually) before this procedure i have forgotten the way to do it, was given on zuk.eu i think, dont worry it may take time but these days hard bricks is repairable too.
Click to expand...
Click to collapse
Isn't removing battery connection means powering off the device???
SilenT__ShadoW said:
Isn't removing battery connection means powering off the device???
Click to expand...
Click to collapse
Yes!
AstroBiswas said:
Yes!
Click to expand...
Click to collapse
I'm doing the same.... Removing battery connection every time to switch off.
SilenT__ShadoW said:
I'm doing the same.... Removing battery connection every time to switch off.
Click to expand...
Click to collapse
Thats strange keep trying, perfect timing matters
AstroBiswas said:
Thats strange keep trying, perfect timing matters
Click to expand...
Click to collapse
What do you mean by perfect timing?!?
Never mind. Got my laptop to recognise it and flashed successfully.
Don't know what made it to change its mind!?
What happened?
- was trying to flash and cable got disconnected by accident.
- my phone started to vibrate and blink at the same time for every 30 sec(no zuk logo nothing) and can't seems to be stopped.
- laptop doesn't seems to recognise when device gets connected (no 900e or 9008 port shows up at device manager)
What I did?
- Reinstalled my windows (no problem for me as I only keep system files on partition c)
- Disabled driver verification (windows 10 thing)
- Installed zuk driver, adb , mi tools inside partition c(all inside a folder called zuk)
- used cable that came with phone instead of 3rd party to deep flash
AstroBiswas said:
This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!
Click to expand...
Click to collapse
Okay fine, somebody suggested me to flash stock ROM via qpst method, because I was having battery issues, the flashing process stopped, and I forgot to untick clean all and lock, this left my phone with a screen saying, 'unable to boot'. PC is not detecting my device now, but earlier I unlocked bootloader and flashed tw recovery, but I wasn't able to boot to it, and on qpst, my phone is detected as Diagnostic Port 900E.
AstroBiswas said:
This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!
Click to expand...
Click to collapse
What if the phone even won't boot tofastboot mode?? It only vibrates every 10 sec or maybe, will EDL cable work??
Can anybody help
sagarsk said:
Not even coming up as 900E
My hard brick z2 is not even coming up as 900E. Basically computer doesn't detect and no changes in device manager either. Please confirm what to do.
I have tried pressing buttons told by many others and in various other forums. It doesn't work. Does deep flash cable method work even if the phone is not detecting in 900E mode?
Click to expand...
Click to collapse
I also have the same question and I am in the same situation
Three days ago, my phone went off by itself and I had a hard time starting again, it was just loading the bootanimation, I tried to reinstall the ROM, but it did not go into TWRP, although the message Recovery appears on the screen, I insisted and after several attempts, I got into the recovery, formatted everything and I installed the AICP ROM again, and I had to restart,my phone freezes in the LeEco bootloader, then again I insisted until the ROM finally started, but soon realized that it was taking too long to start (30 minutes waiting and nothing).
So I rebooted again, and from then on, I can not go into any mode anymore, trying to access the TWRP, the phone only stays on the Recovery screen until reboot after 2 minutes, when letting the phone try to start the ROM, it only stays on the LeEco screen and restart after 2 minutes, when entering Fastboot, it enters the screen in Fastboot mode, but is not recognized by the computer, not even as unknown device, the same for Download mode.
Is there anything I can try?
Doesn't seem like a a fried motherboard. In my experience, If you fried the CPU, you would still be able to access Fastboot, if you fried the GPU part of the chip, or if the LCD has failed you would feel vibrations..
Do you thin it is possible that you accidentally put the phone into EDL mode? It can sometimes be hard to get out of, and it will give you similar issues.
To leave EDL press and hold volume down and power for 1 minute or longer.
Try this
Install the All in One tool and use it to update your android and fastboot drivers. Afterwards see if the computer recognises the phone port connection by going to Control Panel>System> Device Manager* ( Even though, you may not see the drive, you will maybe still see unknown device or te port)
Maybe a Brick?
If it does not see the phone or show a unknown USB device with port 9008
Try placing the phone into EDL mode by pressing and holding the Vol Up (+) and Vol Down (-) together while simultaneously connecting the phone by USB cable to the computer. Do you see the port or phone now? If you see port 9008 you possibly are bricked, follow the steps on my unbricking thread., if you can not get back to TWRP, or fastboot,and the phone keeps a charge. Then I would think that you are definitely bricked.
Other possible issues
The issue could be the battery. Have you tried using other USB C Cables? If you can use a different usb cable let it charge for a couple of hours then see if you can get into TWRP again . If you can enter fastboot mode try reflashing TWRP, you can use the All in One tool for this.
tsongming said:
Doesn't seem like a a fried motherboard. In my experience, If you fried the CPU, you would still be able to access Fastboot, if you fried the GPU part of the chip, or if the LCD has failed you would feel vibrations..
Do you thin it is possible that you accidentally put the phone into EDL mode? It can sometimes be hard to get out of, and it will give you similar issues.
To leave EDL press and hold volume down and power for 1 minute or longer.
Try this
Install the All in One tool and use it to update your android and fastboot drivers. Afterwards see if the computer recognises the phone port connection by going to Control Panel>System> Device Manager* ( Even though, you may not see the drive, you will maybe still see unknown device or te port)
Maybe a Brick?
If it does not see the phone or show a unknown USB device with port 9008
Try placing the phone into EDL mode by pressing and holding the Vol Up (+) and Vol Down (-) together while simultaneously connecting the phone by USB cable to the computer. Do you see the port or phone now? If you see port 9008 you possibly are bricked, follow the steps on my unbricking thread., if you can not get back to TWRP, or fastboot,and the phone keeps a charge. Then I would think that you are definitely bricked.
Other possible issues
The issue could be the battery. Have you tried using other USB C Cables? If you can use a different usb cable let it charge for a couple of hours then see if you can get into TWRP again . If you can enter fastboot mode try reflashing TWRP, you can use the All in One tool for this.
Click to expand...
Click to collapse
Thanks for answering. I've tried everything.
But I can not see the smartphone when connected. USB drivers are properly installed (I used to recover other LeEco x651, x526 and x520 devices)
I left it restarting for more than hours holding the power button and volume down, no results.
The device does not appear in the Windows device manager in any way, not even as Unknown or 9008 port.
I tried several usb cables.
There is no communication with TWRP or ROM installed and neither with the computer, even though I enter into fastboot / 9008 mode. Only LeEco / recovery logo and Fastboot screen.
I think my main memory is damaged or something.
kakobr said:
Thanks for answering. I've tried everything.
But I can not see the smartphone when connected. USB drivers are properly installed (I used to recover other LeEco x651, x526 and x520 devices)
I left it restarting for more than hours holding the power button and volume down, no results.
The device does not appear in the Windows device manager in any way, not even as Unknown or 9008 port.
I tried several usb cables.
There is no communication with TWRP or ROM installed and neither with the computer, even though I enter into fastboot / 9008 mode.sl Only LeEco / recovery logo and Fastboot screen.
I think my main memory is damaged or something.
Click to expand...
Click to collapse
Well that sucks, if you feel like sending to the phone to China for repair, you can find several shops that are offering to repair any damaged Leeco for $10 and an average cost of $30 for resoldering. On the TaoBao website, use Chrome for translation. Some of their ads mention overseas repair
If it's memory it would be an easy fix for them.
If you don't want to fix it, I highly recommend the Mi8 if it's within your budget, its a perfect phone and you can find them for close to $300. My brother has a Redmi note 6 Pro which is also really nice. He paid $190.
Good Luck.
Sent from my Xiaomi MI 8 using XDA Labs
kakobr said:
Thanks for answering. I've tried everything.
But I can not see the smartphone when connected. USB drivers are properly installed (I used to recover other LeEco x651, x526 and x520 devices)
I left it restarting for more than hours holding the power button and volume down, no results.
The device does not appear in the Windows device manager in any way, not even as Unknown or 9008 port.
I tried several usb cables.
There is no communication with TWRP or ROM installed and neither with the computer, even though I enter into fastboot / 9008 mode. Only LeEco / recovery logo and Fastboot screen.
I think my main memory is damaged or something.
Click to expand...
Click to collapse
Check out this possible do it yourself fix : https://forum.xda-developers.com/showpost.php?p=79302729&postcount=71
Background:
OnePlus 8 Pro IN2020
Original OS version is OxygenOS 12 Android 12
How my phone turned into brick:
Try flashboot unsupported TWRP and other third party recoveries.
After a few tries, eventually causing my phone turning into a brick
What my error looks like:
Not able to boot into system
Showing "the current image(boot/recovery) have been destroyed"
Can access fastboot and detect by system
Method:
Follow the steps in How to UNBRICK OnePlus 8 or 8 Pro! by Max Lee (Thank you my man, Max, for this video)
Pitfalls in 2022 (IMPORTANT before UNBRICK!):A USB 2.0 and Third-party USB cable are highly recommendedI was unable to boot into Quadcomm EDL mode while using the stock cable and USB 3.0 connector. Pressing the correct Volumn Up & Volumn Down and Power Button will boot the phone to fastboot in no time.
I successfully got into the EDL mode and finished flashing the phone using my iPad Pro Type-C charging cable which is an USB 2.0 one.
Use a newer version of the Qualcomm driver if you find the device not correctly detectedUse Qualcomm HS-USB QDLoader 9008 driver.
A new Quadcomm driver will help you flash your device correctly the first time!!!
Windows 11 won't let you install unsigned driver by default, but there's a way round
Press Shift key while click Reboot in start menu to enter Advanced Options
Click Trouble shoot in Advanced Options
Click Advanced options, click Startup Settings then click Restart
After restart press 7 when required
If your computer won't restart, just unplug your phone temporarily
after this your device will detect by your computer correctly.
Pressing buttons requires special timing and preconditions and a few more tries
To fully power off your phone, press Volume up and Power button for 10 seconds. Release immediately after the screen turns black.
Your phone is in the state of powered off even your screen displaying error message or charging animation, just make sure it's not in fastboot, recovery or booting animations.
Connect your phone to your computer before press Volume up and down and Power Button all at the same time to enter EDL mode.
Prepare yourself with Device Manager and MSM tool open and configured correctly before your phone enter EDL mode. There's a about 10 second window for you to start flashing.
Fail amid your MSM flash process:Don't panic if you see error message saying you didn't finish flashing
You can flash it anytime just make sure checking all the things above and enter EDL mode
Check these things：
Check your Windows can install the unsigned driver correctly
Check Device Manger in Control Panel if your device is correctly detected as a COM device as Qualcomm HS-USB QDLoader 9008 or something like this
Use administrator privilege to open the MSM software
Check your cable connection is stable or not.
Finally, thanks Dr.E (Max Lee) for your help. Without your video instructions, I won't revive my phone. It spares my pain to ask my dad for money for a new phone I don't actually need.
Hope everyone could find some helpful information in this post and flash your phone like a champ.
A even better way to enter EDL mode is power off and unplug your device, and after hold volume up and down at the same time, plug in the USB 2.0 cable to the computer. It works every time!!
i cant join rdl mode always restarting fastboot mode
So I wanted to flash evolution X, which flashed ok but would only boot into fastboot mode. I then went to flash stock 11 rom using the fastboot rom. It flashed ok but when it came to rebooting, the screen just went black. I cannot enter fastboot, recovery or EDL mode. Regardless of the method to get into EDL mode, the computer wont recognise the phone. Device manager doesnt show anything being plugged in and MSMdownload tool doesnt recognise it either. I have the drivers already installed so the computer should recognise it.
What i did one time was:
Start MSM Tool and press start.
Connected the phone with a third party cable and to a usb hub.
Held vol up, vol down and power button for like a minute or longer.
xtcislove said:
What i did one time was:
Start MSM Tool and press start.
Connected the phone with a third party cable and to a usb hub.
Held vol up, vol down and power button for like a minute or longer.
Click to expand...
Click to collapse
nope. didn't work. phone doesn't get recognised by the computer at all.
Roamed around a bit and solved the issue by following this.
Brick Saved!! OnePlus 8 Pro Oxygen OS 12 to Android 11 downgrade brick saved. Methods I used and pitfalls.
Background: OnePlus 8 Pro IN2020 Original OS version is OxygenOS 12 Android 12 How my phone turned into brick: Try flashboot unsupported TWRP and other third party recoveries. After a few tries, eventually causing my phone turning into a brick...
forum.xda-developers.com
You likely just haven't installed the proper drivers. You need those Qualcomm ones so your PC recognizes the phone. Also try different USB cables.