Related
Okay so long story short: I unlocked my bootloader, flashed twrp and things like that and tried to flash lineage. This was all using the Axon 7 tool. I did something wrong and now I can't get into any other mode but EDL mode. The phone shows up in Miflash but I always get some "cant read hello packet error" and it tries to "reset" and end it eventually just stops and gives me an error. Plz help.
daevion0 said:
Okay so long story short: I unlocked my bootloader, flashed twrp and things like that and tried to flash lineage. This was all using the Axon 7 tool. I did something wrong and now I can't get into any other mode but EDL mode. The phone shows up in Miflash but I always get some "cant read hello packet error" and it tries to "reset" and end it eventually just stops and gives me an error. Plz help.
Click to expand...
Click to collapse
I assume you're not on Windows 10 x64? If you aren't, either get a PC with Win10 x64, or do this:
Connect the phone, get into EDL mode. Now go to the Device Manager, and tell me where it appears.
It can appear as:
-"Qualcomm HS-USB QDLoader 9008" under Ports (COM & LPT);
-"ZTE DFU Interface, under Ports too; or
-"QUSB_BULK" under Universal Serial Bus devices or unknown devices.
If it appears as the DFU stuff, you'll have to follow the 4th category brick repair guide. If it appears as QDLoader, right click on it, then Properties, then go to Bits per second and put the number at 115200 or 128000 if it's not there. Then hold the 3 buttons (vol and power) until Windows beeps and the device manager spazzes and the phone flashes the red led, then try MiFlash again.
If it appears as QUSB_BULK, uninstall the driver (tick delete driver software too) and restart edl.
Choose an username... said:
I assume you're not on Windows 10 x64? If you aren't, either get a PC with Win10 x64, or do this:
Connect the phone, get into EDL mode. Now go to the Device Manager, and tell me where it appears.
It can appear as:
-"Qualcomm HS-USB QDLoader 9008" under Ports (COM & LPT);
-"ZTE DFU Interface, under Ports too; or
-"QUSB_BULK" under Universal Serial Bus devices or unknown devices.
If it appears as the DFU stuff, you'll have to follow the 4th category brick repair guide. If it appears as QDLoader, right click on it, then Properties, then go to Bits per second and put the number at 115200 or 128000 if it's not there. Then hold the 3 buttons (vol and power) until Windows beeps and the device manager spazzes and the phone flashes the red led, then try MiFlash again.
If it appears as QUSB_BULK, uninstall the driver (tick delete driver software too) and restart edl.
Click to expand...
Click to collapse
I'm on win10 64bit
daevion0 said:
I'm on win10 64bit
Click to expand...
Click to collapse
Then do everything I described above or just try another PC. It always happens that one PC can be decided not to let you unbrick your phone for some reason
Choose an username... said:
Then do everything I described above or just try another PC. It always happens that one PC can be decided not to let you unbrick your phone for some reason
Click to expand...
Click to collapse
Is there no other option? is there no other way to at least get fast boot mode back on my phone?
daevion0 said:
Is there no other option? is there no other way to at least get fast boot mode back on my phone?
Click to expand...
Click to collapse
Lol nope, not if EDL is not working for you. You still didn't tell me whether you have a DFU brick or not. If you do have a DFU brick the only surefire way is to disassemble your phone and short a testpad, so don't complain.
Try what I told you above. It may be that it's set at 9600 baud
daevion0 said:
Okay so long story short: I unlocked my bootloader, flashed twrp and things like that and tried to flash lineage. This was all using the Axon 7 tool. I did something wrong and now I can't get into any other mode but EDL mode. The phone shows up in Miflash but I always get some "cant read hello packet error" and it tries to "reset" and end it eventually just stops and gives me an error. Plz help.
Click to expand...
Click to collapse
1. You must use "Qualcomm HS-USB QDLoader 9008" driver (there is another one call zidag but it's not work here)
2. As soos as you enter EDL mode, you must press "Flash" as quick as possible
i'm in a similar situation... i did "fastboot oem lock" and now i'm in a loop trying to boot the phone, after the 3time it enters edl (i see the red light).
My model is de G model (2017G) can i use miFlash just to restore the recovery and fastboot?
i had installed lineageOS, when connecting my phone it says that is the U model (2017U) but i think is only a label tag from the rom...
Thansks for the help!!
A 64 bit computer is not really necessary, however it is adviced.
I used a 32bit laptop running Win 10 to rescue mine.
Drivers seem to be a major problem, having the correct up to date drivers is a must.
Also try using Edl Tool and the Axon7 tool kit to access flashing.
Zadig drivers can help in some instances.
With the error you are receiving, have you tried another Edl package?
I was using an Edl package that would not finish flashing either, try a different package and make sure its correct for your phone.
I hope you get it sorted
The hello read package does occur when the phone is not really EDL mode anymore. You always have to restart the phone and boot manually into EDL mode with + - Power and you have to reboot everytime you did or if the hello error happens.
Look under device manager if it says Qualcomm instead of ZTE Device Handset. If that is the case you can build your own EDL cable.
"First I opened the cable and cut the Black and green open, then I connected all the black and green one together and pressed the power button until the red led was gone and 2 additional seconds.
After that I disconnected the modded cable and connected the Phone to the PC with the orginal cable and it showed up as Qualcomm HS-USB QDLoader 9008. "
You can install the qualcomm drivers under the MiFlash tab in the latest version.
i finally solve my issue following the guide: https://forum.xda-developers.com/axon-7/how-to/a2017-4th-category-brick-repair-manual-t3585898 there is also a resume on https://forum.xda-developers.com/axon-7/how-to/guide-dfu-unbrick-guide-disassembly-t3731152
This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!
I think someone has made this guide already.
I see.
well i have a similar issue that i am stuck at 9008 port that is edl but, i can flash rom via Qfil and Mi Flash toll but i cant boot onto it=
I cant get out of edl mode lol. stuck at it.
I deleted some files from qpst rom for intentionally hard bricking my phone and heres another fix.
Cut the outer plastic and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
Happy Flashing!
AstroBiswas said:
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994 - not last edition, latest is v1.0.8
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270 - not last edition, latest is 2.7.460 (fix "sahara" error)
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download - not needed
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790 - not needed (if you use the previous paragraph).
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
Click to expand...
Click to collapse
@AstroBiswas Read red comment.
Not_James_Bond said:
I think someone has made this guide already.
Click to expand...
Click to collapse
Of course!
https://forum.xda-developers.com/le...-to-recover-hard-bricked-zuk-z2-plus-t3576007
Not even coming up as 900E
AstroBiswas said:
This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!
Click to expand...
Click to collapse
My hard brick z2 is not even coming up as 900E. Basically computer doesn't detect and no changes in device manager either. Please confirm what to do.
I have tried pressing buttons told by many others and in various other forums. It doesn't work. Does deep flash cable method work even if the phone is not detecting in 900E mode?
You have to boot in proper edl mode...for edl mode hold volume up button 15 second and immediately click power button for .5 sec and attach data cable to phone which is connected to pc and & immediately prees again power button. all while procees alway hold volume up button....
Zuk Z2 Pro Stuck in EDL HS-USB 9008 Port and automatically connecting and disconnect
Hi,
My Zuk Z2 Pro is stuck in EDL 9008 Port. Phone is totally bricked and no sound, no light, no vibration. When i connect with the computer, phone is connecting on HS USB 9008 port and get disconnected after 20-22 seconds and again automatically connected with in half second time.
I am facing this issue after flashing a ZUI 1.9 by using a QPAST/QFIL application. I think i have made stupid mistake by flashing a phone with "ERASE ALL BEFORE DOWNLOAD" option.
I have tried every scenario to get stable this 9008 port but no luck. Since last 5 days i am studying forums and applying every kind of solution but same result.
I am writing this post with high expectations and hope someone will take notice and help me to get rid of this problem.
I can pay through paypal if someone wants to provide professional services to resolve this matter
I will appreciate if someone have any idea and can help me. Thanks
Can someine please help me with this weird situation? Device got disconnected while flashing via qfil. Now no zuk logo nothing. Phone vibrates every 30 sec that's it. Wont even gets recognized by my laptop(no 9008 or 900e port!)
SilenT__ShadoW said:
Can someine please help me with this weird situation? Device got disconnected while flashing via qfil. Now no zuk logo nothing. Phone vibrates every 30 sec that's it. Wont even gets recognized by my laptop(no 9008 or 900e port!)
Click to expand...
Click to collapse
You need to use the deep flash guide which involved cutting and sorting the cable , procedure given in last part of OP
AstroBiswas said:
You need to use the deep flash guide which involved cutting and sorting the cable , procedure given in last part of OP
Click to expand...
Click to collapse
I've tired that also. Connecting phone to pc while green and black wires attached together and detaching them after 5 sec. That also did nothing. However i connect my phone to my pc it just vibrates and blinks led every 30 sec till i remove battery!
SilenT__ShadoW said:
I've tired that also. Connecting phone to pc while green and black wires attached together and detaching them after 5 sec. That also did nothing. However i connect my phone to my pc it just vibrates and blinks led every 30 sec till i remove battery!
Click to expand...
Click to collapse
You need to completely poweoff the phone (difficult in hard brick actually) before this procedure i have forgotten the way to do it, was given on zuk.eu i think, dont worry it may take time but these days hard bricks is repairable too.
AstroBiswas said:
You need to completely poweoff the phone (difficult in hard brick actually) before this procedure i have forgotten the way to do it, was given on zuk.eu i think, dont worry it may take time but these days hard bricks is repairable too.
Click to expand...
Click to collapse
Isn't removing battery connection means powering off the device???
SilenT__ShadoW said:
Isn't removing battery connection means powering off the device???
Click to expand...
Click to collapse
Yes!
AstroBiswas said:
Yes!
Click to expand...
Click to collapse
I'm doing the same.... Removing battery connection every time to switch off.
SilenT__ShadoW said:
I'm doing the same.... Removing battery connection every time to switch off.
Click to expand...
Click to collapse
Thats strange keep trying, perfect timing matters
AstroBiswas said:
Thats strange keep trying, perfect timing matters
Click to expand...
Click to collapse
What do you mean by perfect timing?!?
Never mind. Got my laptop to recognise it and flashed successfully.
Don't know what made it to change its mind!?
What happened?
- was trying to flash and cable got disconnected by accident.
- my phone started to vibrate and blink at the same time for every 30 sec(no zuk logo nothing) and can't seems to be stopped.
- laptop doesn't seems to recognise when device gets connected (no 900e or 9008 port shows up at device manager)
What I did?
- Reinstalled my windows (no problem for me as I only keep system files on partition c)
- Disabled driver verification (windows 10 thing)
- Installed zuk driver, adb , mi tools inside partition c(all inside a folder called zuk)
- used cable that came with phone instead of 3rd party to deep flash
AstroBiswas said:
This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!
Click to expand...
Click to collapse
Okay fine, somebody suggested me to flash stock ROM via qpst method, because I was having battery issues, the flashing process stopped, and I forgot to untick clean all and lock, this left my phone with a screen saying, 'unable to boot'. PC is not detecting my device now, but earlier I unlocked bootloader and flashed tw recovery, but I wasn't able to boot to it, and on qpst, my phone is detected as Diagnostic Port 900E.
AstroBiswas said:
This Procedure Can Also Be Used To Flash Stock Rom And To Regain Warranty
Scenarios-
1.You Somehow relocked your bootloader while on custom rom
2.Your phone flashes the zuk logo and then screen goes blank with led blinking and you cant see the options to go to fastboot or other modes
3.Your Phone Shows port 9008 or 900e while connected to PC
3.You want to regain your warranty
4.You just want to go back to stock rom
This Guide Is for All of the Above Sceneriaos
Following this guide will revert your phone back to stock ROM nougat while deleting your user data and relocking your bootloader
WARNING
If your device is already bricked and if it goes worse than I am not responsible for it. Do at your own risk.
Prerequisites-
A)Downloads and Drivers
1.ZUK USB Driver https://www.androidfilehost.com/?fid=745425885120716994
2.QPST tool https://www.androidfilehost.com/?fid=673368273298940270
3.Mi Flash tool(Download Latest Version) http://xiaomiflashtool.com/category/download
4.ADB and fastboot Drivers https://www.androidfilehost.com/?fid=529152257862712103
5.Minimal ADB and Fastboot https://forum.xda-developers.com/showthread.php?t=2317790
6.Qualcomm QHSUSB driver https://androidfilehost.com/?fid=673368273298940267
B)QPST ROM
1.Indian Version Nougat http://www.mediafire.com/file/f86cs...SER_Q01080.2_N_ZUI_2.5.104_ST_170418_QPST.zip
2.Chinese Version Nougat
http://s.bs.zui.com/DGDc
Extract these rom to preferably a new folder in the root of c drive
STEPS
INSTALL ALL TOOLS AND DRIVERS GIVEN ABOVE
A)If phone is running fine
1.Enable USB Debugging on your Device and give permission to any prompts
2.Open Minimal ADB and Fastboot and put the following command
adb reboot edl
OR
Put the phone in fastboot mode, Open Minimal ADB and Fastboot and put the following command
fastboot reboot edl
3.Close Window
4.Open Mi Flash Tool
5.Click "select" button on the upper left and browse to the directory where you extracted your stock rom and click refresh on the right COM port shall appear below
6.Click Flash
7.DONT REMOVE OR DISCONNECT THE USB CABLE FLASHING WILL TAKE SOME TIME
8.After success is shown press the power button for sometime until the phone vibrates first boot will take some time
9.Tada! You are back to stock rom along with your WARRANTY!(If Mi flash doesnt work use QFIL as per given in the steps 1 to 4 given below)
B)If phone doesnt bootup
1. Restart your PC and open QFILClick
2. Select "Flat Build" and "Browse". Now navigate to the extracted ROM/Firmware, and select prog_emmc_firehose_8996_ddr.elf.
3.Select the "load xml" button. This will appear a new explorer. One of them will be needed to navigate to the file
rawprogram0.xml the second one will ask for patch0.xml
4.Turn your phone off. Now press and hold the volume + button, while pressing the power button for 0.5 seconds and plug in the
USB cable in the same moment. If it was successful your phone should appear at QPST/QFIL and you are able to press the
download button. Press the download process and wait to finish.
If it fails, In QFIL Change
"Device Type" to eMMC
"Validation Mode" to 0-No validation
"Reset after Download" no needed to tick (optional)
5.If your phone is not detected in the QFIL or it shows up as port 900E then there are 2 ways to get to 9008 mode
I)
a.Unplug your phone from the computer.
b. Press and hold the POWER button until your phone restarting 3-5 times.
c. After the 3rd times (or more), you will see the notification LED goes off in the middle of boot process, and at that time, quick
press VOLUME + button and release the POWER button but keep the VOLUME + button pressed.
d. Your phone will be at POWER OFF status.
e. After your phone is completely off, press and hold the VOLUME +, then press POWER button and connect your USB at the
same time.
f. Your computer will showing a notification about a new port.
g. If you succeed, you will see Diagnostic Port 9008 at QFIL software
II)
Right click on my computer and select MANAGE, then select Device Manager
See if your device is connected as Diagnostic Port 900E
If it is shown as “QHSUSB_BULK” under Other Device
a. Right-click on QHSUSB_BULK and choose “Update Driver Software“
b. Now click on the Browse button and locate the extracted Qualcomm QDLoader drivers.
c. The installation process shall take place immediately and a system notification will appear. Just choose “Install this driver software anyway“.
d.Click the Close button and check back at Device Manager window. You will now see “Qualcomm HS-USB QDLoader 9008 (COM10)” under Ports (COM & LPT) section.
6. Flash your phone using QFIL software once phone connects in 9008 mode and then reboot.
(Alternatively you can also use the Mi Flash Tool once the phone is in 9008 port)
7.Tada! You have successfully unbricked your phone and regained your WARRANTY!
Update: For saving your user data if your phone gets bricked by bootloader getting locked ONLY follow the below guide
How To-
1. How to switch it off
-firstly this is happening because you have locked you're bootloader
- You have black screen and led on so just hold power button then Zuk logo will be flash after that you will get black screen again and again the phone was preparing to reboot but before that the led will get turn off immediately release power button
- You have it Your phone is switched off
(Let it reboot once after that don't leave the power button and after that led will get off for small time this is the time you have to remove finger from power button this is tricky )
2. Going to Bootloader
-Firstly connect the USB to laptop
-after you have switched off your phone press volume up and down together and with holding buttons connect the phone to USB and you will see the fastboot mode
3. Unlock your phone
-Remember the unlock bootloader file in your email re download it and unlock your bootloader again(no need to redownload if you already have it the file is permanent)
- after unlocking phone you will see phone rebooted press power button reboot press volume the volume button and go to reboot option
- go to fastboot and flash the TWRP and you will see that your data on internal storage is present so flash any ROM and you will see your data
Update: Deep flash using Deep Flash Cable And Procedure to make a deep flash cable
Cut the outer rubber and metal covering of usb cable.
Strip a small portion of the black and green wires carefully preferably using a needle to avoid the copper wires to be torn.
Then plug the usb jack into the pc and phone and keep mi flash tool open.
Then touch both the wires(shortcircuit the green and black) using a needle or blunt edge of knief for about 4-5 sec and then remove.
The phone must be in 9008 mode now with COM port open in miflash tool
Now Flash To Your Hearts Content!
After flashing carefully cover the cut portion by putting the rubber casing first and then covering with electrical tape.
So be careful not to tear anything you just need to precisely cut the covering (around 0.5 cm) in the shape of a ring
Happy Flashing!
Click to expand...
Click to collapse
What if the phone even won't boot tofastboot mode?? It only vibrates every 10 sec or maybe, will EDL cable work??
Can anybody help
sagarsk said:
Not even coming up as 900E
My hard brick z2 is not even coming up as 900E. Basically computer doesn't detect and no changes in device manager either. Please confirm what to do.
I have tried pressing buttons told by many others and in various other forums. It doesn't work. Does deep flash cable method work even if the phone is not detecting in 900E mode?
Click to expand...
Click to collapse
I also have the same question and I am in the same situation
My Axon 7 is the A2017U, i had the B32 Nougat running on it and wanted to try the new lineageos 15.1, but had to unlock my bootloader first i used the toolkit like I've done in the past and was able to unlock it and flash twrp, when i try to boot it back on it goes to factory testing mode, i was able to get into twrp and i wiped everything and it stopped the problem of booting directly to FTM but after that i tried to go into EDL mode and it seemed to try to enter the mode but the red led indicator light stays on rather than doing a quick blink. its no longer picked up as a COM port, when i enter fastboot mode adb doesn't seem to work and I'm unsure what to do or if I'm out of luck. Thank you for your time and the advice and help you guys are able to provide.
use ADB
Enable ADB in developer options
use command "adb reboot edl"
Used Twrp to flash Custom ROM, EDL still not fixed
sauerkraut17 said:
use ADB
Enable ADB in developer options
use command "adb reboot edl"
Click to expand...
Click to collapse
I had no OS installed, only twrp recovery and I was able to unlock my boot loader. I tried to flash Lineage-OS ROM in twrp and didn't have much luck because i would get an error code saying it wasn't compatible with my phone and had to go into the ROM files and edit the updater-script file to remove the compatibility check.
In the end I have a working phone with a custom ROM but EDL mode is still not responsive and seems to freeze my phone as soon as I press the 3 buttons to get into EDL. the notification light blink remains on so ill take it as an indicator that something is wrong with the firmware that it uses. i still want to fix it so EDL can be used but unsure how to fix it. I did some researching and was wondering if using a deep flash Engineering cable would work to fix the EDL mode and any other problems that could be there.
levittc5280 said:
I had no OS installed, only twrp recovery and I was able to unlock my boot loader. I tried to flash Lineage-OS ROM in twrp and didn't have much luck because i would get an error code saying it wasn't compatible with my phone and had to go into the ROM files and edit the updater-script file to remove the compatibility check.
In the end I have a working phone with a custom ROM but EDL mode is still not responsive and seems to freeze my phone as soon as I press the 3 buttons to get into EDL. the notification light blink remains on so ill take it as an indicator that something is wrong with the firmware that it uses. i still want to fix it so EDL can be used but unsure how to fix it. I did some researching and was wondering if using a deep flash Engineering cable would work to fix the EDL mode and any other problems that could be there.
Click to expand...
Click to collapse
EDL using the volume/power button has issues with the newer bootstack (which it sounds like you're on). However, since you have an OS now do as I recommended. It will 'reset' the EDL and once done via ADB command it will work with the volume/power buttons like it did before moving forward.
sauerkraut17 said:
EDL using the volume/power button has issues with the newer bootstack (which it sounds like you're on). However, since you have an OS now do as I recommended. It will 'reset' the EDL and once done via ADB command it will work with the volume/power buttons like it did before moving forward.
Click to expand...
Click to collapse
Using the ADB command i was able to get into EDL mode and it was able to get a COM port. using the volume + power buttons had the same problem. Would using an older bootstack fix it?
levittc5280 said:
Using the ADB command i was able to get into EDL mode and it was able to get a COM port. using the volume + power buttons had the same problem. Would using an older bootstack fix it?
Click to expand...
Click to collapse
Have the same issue as you do after installing the bootstack. but even with the adb reboot edl command my phone just restarts normally.. But my OS is working fine, is there any way?
Try to use volume up and volume down only and plugging in USB cable........
stinka318 said:
Try to use volume up and volume down only and plugging in USB cable........
Click to expand...
Click to collapse
Tried everything already. Can only get to DFU mode..
So, I have a similar problem: after flashing a new version of TWRP, now Recovery doesn't start. The problem is that I haven't any OS installed and the last chance to save the phone should be reflash stock by EDL... BUT EDL mode doesn't start if I press vol UP + vol DOWN during power on... (it became black with a red light, but if I digit "ADB devices" on ADB, no devices seems connected, and in the same way it's impossible to use Axon7Toolkit). So: no Recovery, no EDL mode, no OS installed, my phone is a paperweight.
Is there a method to save my Axon 7?
Here is something to try ...
Enter edl via button combo (volup + voldn + pwr)
You should have a black screen ...
Now plug your phone into the cable on your PC/laptop ..
If your PC / laptop doesn't recognise your phone via Miflash or app you are using ...
Try tapping the power button once ...this seems to open/close the port ...
I noticed this when I was using edl mode to flash a ROM
I hope this helps
levittc5280 said:
My Axon 7 is the A2017U, i had the B32 Nougat running on it and wanted to try the new lineageos 15.1, but had to unlock my bootloader first i used the toolkit like I've done in the past and was able to unlock it and flash twrp, when i try to boot it back on it goes to factory testing mode, i was able to get into twrp and i wiped everything and it stopped the problem of booting directly to FTM but after that i tried to go into EDL mode and it seemed to try to enter the mode but the red led indicator light stays on rather than doing a quick blink. its no longer picked up as a COM port, when i enter fastboot mode adb doesn't seem to work and I'm unsure what to do or if I'm out of luck. Thank you for your time and the advice and help you guys are able to provide.
Click to expand...
Click to collapse
I had the same problem a few days ago. When I booted to EDL Mode the red led was instantly on but the PC recognized it somthing like ZTE Handset Device Mode.
1. You can download TWRP Treble by NFound and flash it via your TWRP. Then reboot to recovery again and under the reboot tab its possible to boot to EDL/9008 Mode.
2. You build a EDL Cable to get the device from the red light to EDL mode. Just open some usb cable and connect the green and black (all four) together, plug it in the device and press the power button
until the red light is gone and hold on two additional seconds. Then remove the cable and plug another working cable in and the PC recognize it as Qualcomm in EDL mode.
This is literally how I unbricked my device.
Syberclone said:
Here is something to try ...
Enter edl via button combo (volup + voldn + pwr)
You should have a black screen ...
Now plug your phone into the cable on your PC/laptop ..
If your PC / laptop doesn't recognise your phone via Miflash or app you are using ...
Try tapping the power button once ...this seems to open/close the port ...
I noticed this when I was using edl mode to flash a ROM
I hope this helps
Click to expand...
Click to collapse
Thanks, I tried but this doesn't solve my problem. The strange thing is that connecting my phone in EDL mode, the phone appears in device manager as COM port, but is not seen launching an "ADB devices" command and is not seen in MiFlash too. I tried to change drivers from "ZTE device (something)..." to "Qualcomm HS-USB QDLoader 9008" and in this way, although ADB doesn't detect nothing yet, MiFlash detects a COM port, but flashing an EDL image still fails with a "cannot receive hello packet" error.
Now I ordered a deep flash cable, hope this can solve... next week I'll know if it works.
Thanks, I tried but this doesn't solve my problem. The strange thing is that connecting my phone in EDL mode, the phone appears in device manager as COM port, but is not seen launching an "ADB devices" command and is not seen in MiFlash too. I tried to change drivers from "ZTE device (something)..." to "Qualcomm HS-USB QDLoader 9008" and in this way, although ADB doesn't detect nothing yet, MiFlash detects a COM port, but flashing an EDL image still fails with a "cannot receive hello packet" error.
Now I ordered a deep flash cable, hope this can solve... next week I'll know if it works.
Click to expand...
Click to collapse
Did you resolve problem?
spasacamen said:
Thanks, I tried but this doesn't solve my problem. The strange thing is that connecting my phone in EDL mode, the phone appears in device manager as COM port, but is not seen launching an "ADB devices" command and is not seen in MiFlash too. I tried to change drivers from "ZTE device (something)..." to "Qualcomm HS-USB QDLoader 9008" and in this way, although ADB doesn't detect nothing yet, MiFlash detects a COM port, but flashing an EDL image still fails with a "cannot receive hello packet" error.
Now I ordered a deep flash cable, hope this can solve... next week I'll know if it works.
Click to expand...
Click to collapse
No need to order that cable... If you still can cancel it i'd tell you to do that. You made a mistake by changing the drivers, you had the "ZTE Handset Diagnostic Interface (DFU)" driver, and replaced it with the EDL driver.
This of course does not work because your phone is in DFU MODE instead of EDL. What you have to do is uninstall the device via device manager and also tick "Uninstall driver software for this device", then turn the phone off and enter DFU again, and then use MultiDL from this forum to enter EDL. After that, use MiFlash or EDL Tool, and try flashing a FULL EDL file
By the way ADB will only work on FTM mode or the recovery or on a working system. You won't get ADB on edl mode or dfu mode because they simply don't have adb working, it's normal
i never use xda but this quote thing is what i have aswell
levittc5280 said:
Using the ADB command i was able to get into EDL mode and it was able to get a COM port. using the volume + power buttons had the same problem. Would using an older bootstack fix it?
Click to expand...
Click to collapse
all i see is the red light in edl, whatever i try it Always just goes to a red light and a black screen. this happened after trying to unlock the bootloader. i was in android 8 and tried to lock it, it messed it up as my Phone could not boot anymore, i flashed the stock android 6.0 or something that came with the axon 7 toolkit and it did work but when trying to unlock the bootloader as the device state suddenly was locked it broke the whole thing and i oped edl could save me but even that is broken just like what the person in the quote has
Well the only fix to get EDL mode is through test point, there's a thread of unbricking Axon 7 using test point, find it, you'll need to open your back cover to do this
This in case nothing works to get into EDL mode.
Background:
OnePlus 8 Pro IN2020
Original OS version is OxygenOS 12 Android 12
How my phone turned into brick:
Try flashboot unsupported TWRP and other third party recoveries.
After a few tries, eventually causing my phone turning into a brick
What my error looks like:
Not able to boot into system
Showing "the current image(boot/recovery) have been destroyed"
Can access fastboot and detect by system
Method:
Follow the steps in How to UNBRICK OnePlus 8 or 8 Pro! by Max Lee (Thank you my man, Max, for this video)
Pitfalls in 2022 (IMPORTANT before UNBRICK!):A USB 2.0 and Third-party USB cable are highly recommendedI was unable to boot into Quadcomm EDL mode while using the stock cable and USB 3.0 connector. Pressing the correct Volumn Up & Volumn Down and Power Button will boot the phone to fastboot in no time.
I successfully got into the EDL mode and finished flashing the phone using my iPad Pro Type-C charging cable which is an USB 2.0 one.
Use a newer version of the Qualcomm driver if you find the device not correctly detectedUse Qualcomm HS-USB QDLoader 9008 driver.
A new Quadcomm driver will help you flash your device correctly the first time!!!
Windows 11 won't let you install unsigned driver by default, but there's a way round
Press Shift key while click Reboot in start menu to enter Advanced Options
Click Trouble shoot in Advanced Options
Click Advanced options, click Startup Settings then click Restart
After restart press 7 when required
If your computer won't restart, just unplug your phone temporarily
after this your device will detect by your computer correctly.
Pressing buttons requires special timing and preconditions and a few more tries
To fully power off your phone, press Volume up and Power button for 10 seconds. Release immediately after the screen turns black.
Your phone is in the state of powered off even your screen displaying error message or charging animation, just make sure it's not in fastboot, recovery or booting animations.
Connect your phone to your computer before press Volume up and down and Power Button all at the same time to enter EDL mode.
Prepare yourself with Device Manager and MSM tool open and configured correctly before your phone enter EDL mode. There's a about 10 second window for you to start flashing.
Fail amid your MSM flash process:Don't panic if you see error message saying you didn't finish flashing
You can flash it anytime just make sure checking all the things above and enter EDL mode
Check these things：
Check your Windows can install the unsigned driver correctly
Check Device Manger in Control Panel if your device is correctly detected as a COM device as Qualcomm HS-USB QDLoader 9008 or something like this
Use administrator privilege to open the MSM software
Check your cable connection is stable or not.
Finally, thanks Dr.E (Max Lee) for your help. Without your video instructions, I won't revive my phone. It spares my pain to ask my dad for money for a new phone I don't actually need.
Hope everyone could find some helpful information in this post and flash your phone like a champ.
A even better way to enter EDL mode is power off and unplug your device, and after hold volume up and down at the same time, plug in the USB 2.0 cable to the computer. It works every time!!
i cant join rdl mode always restarting fastboot mode
Hello there members.
i have a Nothing Phone 1 in Edl Mode. Tried to restart it but still connected on Edl. i have searched around for this problem but sill unlucky to find a solution.
Client pretend to have played with roms and flashed the wrong one.
Any help suggestion?
pogradecari said:
Hello there members.
i have a Nothing Phone 1 in Edl Mode. Tried to restart it but still connected on Edl. i have searched around for this problem but sill unlucky to find a solution.
Client pretend to have played with roms and flashed the wrong one.
Any help suggestion?
Click to expand...
Click to collapse
Try holding power+volup+voldown with the phone unplugged from a computer.
If it doesn't work, let me know.
how to boot to edl mode ??
Try this :
Install ADB and Minimal Fastboot drivers through which Windows will recognize your Device.
Enable USB Debugging on your Android Device. You can do this simply by following the given direction:
Settings > About Phone > tap 7 times on the Build Number. This will enable Developer options on it.
Now, again go back to the main Settings > Developer options > USB Debugging and Enable it.
Connect your smartphone with your PC via a USB cable.
Open Command Window by the press and hold Shift Key + right-click of your Mouse.
Choose Open Command Window here.
Type the following command and press the Enter button to check whether the device is connected or not.
" adb devices "
You will see a device serial code on the screen. That means it is successfully connected. Then follow the next step.
Type the command from below and hit enter to Boot into Download Mode (EDL Mode):
" adb reboot edl " or "fastboot oem edl" or "fastboot reboot-edl" or "fastboot reboot edl"
muppetz said:
Try this :
Install ADB and Minimal Fastboot drivers through which Windows will recognize your Device.
Enable USB Debugging on your Android Device. You can do this simply by following the given direction:
Settings > About Phone > tap 7 times on the Build Number. This will enable Developer options on it.
Now, again go back to the main Settings > Developer options > USB Debugging and Enable it.
Connect your smartphone with your PC via a USB cable.
Open Command Window by the press and hold Shift Key + right-click of your Mouse.
Choose Open Command Window here.
Type the following command and press the Enter button to check whether the device is connected or not.
" adb devices "
You will see a device serial code on the screen. That means it is successfully connected. Then follow the next step.
Type the command from below and hit enter to Boot into Download Mode (EDL Mode):
" adb reboot edl "
Click to expand...
Click to collapse
my phone is bricked while flashing stock rom via fastboot
so unable to boot to recovery or bootloader
To begin with, power off your device. If you can’t do so, then you will have to wait until the battery completely drains out.
Now connect one end of the USB cable to your PC, but don’t attach the other end to the device.
Press and hold the Volume Up and Volume Down buttons together for a few seconds.
Now connect the other end of the device to the USB cable.
Your device will now be recognized as Qualcomm HS-USB QDLoader 9008. You may now flash the device-specific firmware to unbrick it.
Even you have a black screen , PC does recognize your phone . Use only a USB 2.0 port . Verify if Qualcomm USB Driver have been installed on Windows .
muppetz said:
To begin with, power off your device. If you can’t do so, then you will have to wait until the battery completely drains out.
Now connect one end of the USB cable to your PC, but don’t attach the other end to the device.
Press and hold the Volume Up and Volume Down buttons together for a few seconds.
Now connect the other end of the device to the USB cable.
Your device will now be recognized as Qualcomm HS-USB QDLoader 9008. You may now flash the device-specific firmware to unbrick it.
Even you have a black screen , PC does recognize your phone . Use only a USB 2.0 port . Verify if drivers have been installed on Windows .
Click to expand...
Click to collapse
tried these steps but phone goes in 900E mode
OK , look then at this :
muppetz said:
OK , look then at this :
Click to expand...
Click to collapse
it does not work as he just changed the drivers from diagnostic mode to qdloader mode
pogradecari said:
Hello there members.
i have a Nothing Phone 1 in Edl Mode. Tried to restart it but still connected on Edl. i have searched around for this problem but sill unlucky to find a solution.
Client pretend to have played with roms and flashed the wrong one.
Any help suggestion?
Click to expand...
Click to collapse
Maybe it's too late already but you can unbrick the phone with this tool
Unbrick / Flash Stock Rom (1.1.7 global) QDLoader 9008 fix | EDL Mode fix
Hi everyone, If your phone (1) does not react on any of yours actions. You may have the same problem. This is an instruction how to fix it without Disassembly. ‼️ Do this at your own risk, I am not responsible for any damage that may occur to...
forum.xda-developers.com
none of these will work
pogradecari said:
none of these will work
Click to expand...
Click to collapse
Why? Have you tried?