I have a problem after installing TWRP on my P9 Lite i have a screen saying:
Your device has been unlocked and can't be trusted
To Learn more, visit: long www adress
Your device is booting now...
Cant put a picture because i don't know how. But this is all it says, and then nothing else happens. Just stays on that screen. Can't connect to my pc or reboot in Recovery mode it always ends here.
Hopefully one of you guys can help. In a bit of panic.
Can't shut it down, everytime i try to turn it off, it reboots into this screen.
Can tell us some more information? Like what ROM are you on now, what TWRP you used etc..
Potato997 said:
Can tell us some more information? Like what ROM are you on now, what TWRP you used etc..
Click to expand...
Click to collapse
I Used TWRP 3.1.1.0 and havn't gooten to custom rom, i am on Android Nougat with EMUI 5.0.
Cant start it other then ending on this screen. I managed to get it booting again, but now my Bluetooth didn't work. So i tryed again and now i am stuck again.
It's a B380 Model
Potato997 said:
Can tell us some more information? Like what ROM are you on now, what TWRP you used etc..
Click to expand...
Click to collapse
Just tryed to make the dload folder on the root of my SDcard but still no success. I havn't been able to start boot screen other than this locked screen.
I have tryed to start with volume up + power both volume up and down + power and volume down + power. Nothing changes, just get this screen everytime.
Cant do anything, not even shut the phone down, it only reboots. I have seen other simular problems, but they have been able to get to the screen with 3 options. I havn't been able to come to that part.
Plug USB cable to your phone but not on your computer, restart the phone and as soon as it restart press volume + (or volume - I don't remember which is fastboot) and plug the USB cable to the computer. So you can check if the bootloader is unlocked
Potato997 said:
Plug USB cable to your phone but not on your computer, restart the phone and as soon as it restart press volume + (or volume - I don't remember which is fastboot) and plug the USB cable to the computer. So you can check if the bootloader is unlocked
Click to expand...
Click to collapse
I can't get to fastboot, dosn't matter what i do. I have no clue what have happened.
stubbeDk81 said:
I can't get to fastboot, dosn't matter what i do. I have no clue what have happened.
Click to expand...
Click to collapse
After i ran out of power and the phone went out. I have been able to boot again. Anybody who knows a bootloader i can install that works on my phone for sure. My bootloader is ****ed up.
It is unlocked now, so i have to be sure it works.
Related
Okay so I seem to have run into a little problem I was planning on updating cleanrom up to 1.2.5 but was on cwm. I had managed to switch over successfully to twrp 2.2.0. I went ahead and used goo manager to download the updated zip of 2.2.1 and tried flashing it thru twrp. Now I am stuck in google bootloop and cant get into recovery or more importantly bootloader. I have been trying last 30mins to hold power and both volume buttons but it either keeps rebooting back to the google screen or not doing anything at all just have to repress to to turn it off but it will turn back on automatically. I tried hooking it up to my usb and labtop but it looks like it wont even recognize it. I just fully charged it so I am good for now just a little worried cant get out of this mess.
I ran into a problem like that with clockwork recovery it kept on rebooting in recovery but I could still go into download mode I was at work away from my computer so I had no choice but to keep trying that three button magic until it finally restored a backup I had on my external card.just keep on trying to pull the battery then try to go into recovery. You might 've gotten a bad download
Sent from my SGH-T999 using xda premium
problem is I cant get into recovery. or the green screen to get to bootloader. It just completely stuck in a bootloop on the google screen mocking me... I am really contemplating opening it up and taking out battery but is that a good idea? Or is there anything else I can do?
so I pulled off the back cover but really dont want o disconnect the battery might mess something up but I cannot get the device to shut off.
disconnecting the battery does nothing it shuts it off and keeps it off but when I connect it to the charger the battery symbol pops up for a second and then goes completely blank. I went ahead and tried again to boot into bootloader pressing power vol up + down and all combinations of power vol -, power vol +
power turbo press vol +/- but no luck still in google screen.
If you're in a bootloop you need to connect your Nexus 7 to a computer. Then you will be able to access recovery via the Power button and volume buttons.
is it going to make a difference that everytime i try to reboot it just the black google screen? I have tried it connected to the wall charger and connected usb to the labtop but nothing.
clago87 said:
is it going to make a difference that everytime i try to reboot it just the black google screen? I have tried it connected to the wall charger and connected usb to the labtop but nothing.
Click to expand...
Click to collapse
It's supposed to do that when you're trying to go to recovery from bootloader without the USB cable plugged into a computer, may need to have the drivers installed on said computer. It's an issue with the nexus 7 bootloader and every one of them does it. What your experiencing is perfectly normal if you tried to go to recovery from bootloader with the bolume buttons and then got the google screen bootloop.
If it doesn't work when you plug it in and try, then try unplugging it, manually rebooting with it plugged in first, or vice versa
Update: I can get on Team Viewer and remotely reboot you into recovery through the PC if you want, or at least give it my best shot.
ok so i disconnected battery and have the device off. I should then try connecting it to the pc and try booting up holding down all buttons?
clago87 said:
ok so i disconnected battery and have the device off. I should then try connecting it to the pc and try booting up holding down all buttons?
Click to expand...
Click to collapse
Have you installed the right drivers on the computer you're using, for ADB and the device drivers, when you unlocked and rooted?
Answer to your question is yes try that. But I wouldn't be disconnecting and reconnecting it, I can't recommend that and then learn tomorrow that static zapped something important.
yea I am getting nothing by connecting to pc. I have all the drivers adb and fastboot installed when I rooted and unlocked couple weeks back but it looks like device is not being recognized or read at all by the pc.
connecting to the pc holding the volume + button gets it recognized for a second and tries to install a driver apx but unsuccessfully.
I am not making any progress whatsoever kinda sucks starting the weekend like this. I have gone thru some bad stuff with my atrix but nothing like this were I cant even access my bootloader boot into recovery or even fastboot. Should I try and get it to just stay off and see if overnight it works its own magic? Hate going to sleep witht his on my mind but I think with a clear mind in the morning something good will happen.
I can get it to stay off by holding both vol+ and vol- but trying to turn it off with just the power button just keeps it turning back on/off...
so I slepted on it thru the night let the tablet rest but went back this morning and I still cant get into bootloader or recovery. Is there anything I can do?
Has anyone else had this problem where they cant boot into recovery or bootloader? It's like the power button and vol keys are unresponsive even though they still work to turn on the device.
are you sure that you flashed the right recovery? but you should still be able to get the bootloader. are you pressing power + volume down(volume down, not both volume buttons. i noticed you wrote both volume buttons) to get into the bootloader?
I think I chose the right recovery the first version downloaded thru goo manager but it was the 2.2.0 version. I had the option on the of downloading the 2.2.1 zip or the .img but i downloaded the .img to just to flash with the current version of twrp that was working. There have been times were I have not been able to get into recovery on my atrix or htc but I've always been able to get into the bootloader this is the first time I've been locked out of my device kind of got me scared its not even a month old. So you say to get into bootloader you dont have to hold down both volume buttons? I will try again to power back up using the volume down and power button at same time... Wish me luck
clago87 said:
I think I chose the right recovery the first version downloaded thru goo manager but it was the 2.2.0 version. I had the option on the of downloading the 2.2.1 zip or the .img but i downloaded the .img to just to flash with the current version of twrp that was working. There have been times were I have not been able to get into recovery on my atrix or htc but I've always been able to get into the bootloader this is the first time I've been locked out of my device kind of got me scared its not even a month old. So you say to get into bootloader you dont have to hold down both volume buttons? I will try again to power back up using the volume down and power button at same time... Wish me luck
Click to expand...
Click to collapse
good luck!
yea, only power button and the volume down button.
quick question before I connect the battery does it make a difference whether or not I have it plugged in charging or connected to the PC while trying to boot into bootloader?
hello,
after install some rom, my p9 lite get bootloop. I manage to enter fastboot but phone was locked, so to install twrp i unlocked it.
After unlock i can't enter fastboot.
Screen "your devices has been unlocked and can't be trusted" appears, vol up+- power, nothing happens phone vibe 2 times and back to screen "your devices...".
My bootloader is unlock, can i flash twrp without bootloader screen on phone ? My phone is connected to PC but no device detected. Maybe at linux i can do something more than windows ?
Maybe i need to go to fastboot some different way ? i try to push 3 button after fist vibe and 2nd. Nothing work for me :crying:
i tried to past b130 to sd card in dload, vol+- power, nothing not even update screen, same "your devices"....,
now downloading b151
dragon218 said:
hello,
after install some rom, my p9 lite get bootloop. I manage to enter fastboot but phone was locked, so to install twrp i unlocked it.
After unlock i can't enter fastboot.
Screen "your devices has been unlocked and can't be trusted" appears, vol up+- power, nothing happens phone vibe 2 times and back to screen "your devices...".
My bootloader is unlock, can i flash twrp without bootloader screen on phone ? My phone is connected to PC but no device detected. Maybe at linux i can do something more than windows ?
Maybe i need to go to fastboot some different way ? i try to push 3 button after fist vibe and 2nd. Nothing work for me :crying:
i tried to past b130 to sd card in dload, vol+- power, nothing not even update screen, same "your devices"....,
now downloading b151
Click to expand...
Click to collapse
For fastbooting u need to use volume down and power in the same time and the phone needs to be connected to PC, and for entering to recovery u only need to press volume up and power key.
robi10101298 said:
For fastbooting u need to use volume down and power in the same time and the phone needs to be connected to PC, and for entering to recovery u only need to press volume up and power key.
Click to expand...
Click to collapse
phone is connected to pc. screen is on "your device..." i push vol down + power. screen going black vibe 2 times, 1 sec huawei logo and back to "your device..". I don't know why after unlock phone i can't go to fastboot
i it possible to erase fastboot ??!!
dragon218 said:
phone is connected to pc. screen is on "your device..." i push vol down + power. screen going black vibe 2 times, 1 sec huawei logo and back to "your device..". I don't know why after unlock phone i can't go to fastboot
Click to expand...
Click to collapse
Disconnect the phone from PC. Make sure it's powered off. Plug in USB cable at the same time while holding volume down.
zgomot said:
Disconnect the phone from PC. Make sure it's powered off. Plug in USB cable at the same time while holding volume down.
Click to expand...
Click to collapse
don't work, after power on still going to "your devices". Even change pc and usb cable
I can belived that i can open fastboot when phone was lock, after unlock fastboot vanished
dc-phoenix can help if pc dont see device ?
dragon218 said:
don't work, after power on still going to "your devices". Even change pc and usb cable
I can belived that i can open fastboot when phone was lock, after unlock fastboot vanished
dc-phoenix can help if pc dont see device ?
Click to expand...
Click to collapse
Don't work, after power on......why power on?
Disconnect from PC. Power of the phone.
Press and hold only vol down, with pressing vol down connect with PC. Device should be start on fastboot mode.
Sent from my NEM-L21 using Tapatalk
Anonda said:
Don't work, after power on......why power on?
Disconnect from PC. Power of the phone.
Press and hold only vol down, with pressing vol down connect with PC. Device should be start on fastboot mode.
Sent from my NEM-L21 using Tapatalk
Click to expand...
Click to collapse
in 5 min i will send video i think i'm doing everything right
if u can look at it
http://sendvid.com/svihvenb
No compatible source was found this video
Sent from my NEM-L21 using Tapatalk
Anonda said:
No compatible source was found this video
Sent from my NEM-L21 using Tapatalk
Click to expand...
Click to collapse
try this from yt
https://youtu.be/K36zMsaP4As
try putting update.app file into dload folder on your sdcard and updating via three button method.
sirjohnrl said:
try putting update.app file into dload folder on your sdcard and updating via three button method.
Click to expand...
Click to collapse
Try with b130 and b161 for region c432 nothing happened. 2 days ago i change region from c185 to c432 now i think maybe i need to past c185b161 to work ?
update doesn't start either, losing hope some one have any other ideas ?
dragon218 said:
try this from yt
https://youtu.be/K36zMsaP4As
Click to expand...
Click to collapse
On the starting, your phone is on.
Then you shutdown? How?
After power off
Press and hold only vol down, connect with pc.
Hi suit installed on your PC?
Sent from my NEM-L21 using Tapatalk
Anonda said:
On the starting, your phone is on.
Then you shutdown? How?
After power off
Press and hold only vol down, connect with pc.
Hi suit installed on your PC?
Sent from my NEM-L21 using Tapatalk
Click to expand...
Click to collapse
i hold power button, if phone isn't connected to pc he is going off. Think is because battery is very low, led is blinking in red.
Then I hold vol down and connect usb cable, but how u can see on video phone weak up and go to booting.
I have hi suit last night as i mention fastboot works, but need to unlock phone. After that "your devices" screen came out and can't fastboot anymore
When i turning off phone with connected usb i can't turn phone off. After a second phone power on by his own.
If phone is disconnected longer than 5 min, then i push vol down and connect usb only red lightening shows up. I need to wait a while to phone start.
dragon218 said:
i hold power button, if phone isn't connected to pc he is going off. Think is because battery is very low, led is blinking in red.
Then I hold vol down and connect usb cable, but how u can see on video phone weak up and go to booting.
I have hi suit last night as i mention fastboot works, but need to unlock phone. After that "your devices" screen came out and can't fastboot anymore
When i turning off phone with connected usb i can't turn phone off. After a second phone power on by his own.
If phone is disconnected longer than 5 min, then i push vol down and connect usb only red lightening shows up. I need to wait a while to phone start.
Click to expand...
Click to collapse
OK. When phone is off, if you connect with PC, phone should be start, but this is only for charging. May be, you don't have charge, so phone is not going to fastboot mode with vol down?
Now just connect the phone with PC for full charge.
You don't have any recovery? Custom or stock?
It can be happen?
Sent from my NEM-L21 using Tapatalk
Anonda said:
OK. When phone is off, if you connect with PC, phone should be start, but this is only for charging. May be, you don't have charge, so phone is not going to fastboot mode with vol down?
Now just connect the phone with PC for full charge.
You don't have any recovery? Custom or stock?
It can be happen?
Sent from my NEM-L21 using Tapatalk
Click to expand...
Click to collapse
When i start charge phone blinking red in led, after while phone vibe 1 time and go to booting now, but led don't stop blinking. I will try to charge it, but because of working screen, phone heat a lot i don't wanna burn it.
Before i made rollback and something gone very bad, emui update after 100 % phone don't boot up. Without usb cable i wasn't able to go recovery or fastboot. So i think i don't have any recovery i made backup of files with twrp but now i can't flash it.
after night without power, phone drain all of battery. Now i understood better what is going on. when i plugged usb cable, phone don't start bye it own, only red lighting flash for second .
I disconnect cable and connect it with vol down button how all of here wrote. Phone immediately weak up an go to "your device has been..".
It's look like after i unlock phone (bootloader) somehow i was able to corrupt bootloader files or even delete it. Some one can confirm that it is possible to crash bootloader ?
dragon218 said:
after night without power, phone drain all of battery. Now i understood better what is going on. when i plugged usb cable, phone don't start bye it own, only red lighting flash for second .
I disconnect cable and connect it with vol down button how all of here wrote. Phone immediately weak up an go to "your device has been..".
It's look like after i unlock phone (bootloader) somehow i was able to corrupt bootloader files or even delete it. Some one can confirm that it is possible to crash bootloader ?
Click to expand...
Click to collapse
I have the same situation. I tried everything, Three button method, letting the battery run out completely, Vol+ and Power, Vol- and Power, connected to PC, not connected to PC. Every time I disconnect the charger, and reconnect it starts from 0. I read some other people here have the same problem. Send it to warranty and explain your rollback process unlocked the bootloader somehow (I mean the phone does do a lot of sh*ty sh*t, so this shouldn't seem very odd as well!!!) and hope that you get a repair/replacement and after that sell it on ebay hoping some stupid people like us in the first place will buy it and spend your money on a phone more reliable!
I managed to access the fastboot using the 3 button method in cold boot. Hold the Power key until the screen goes off and then release and hold down the Vol- key and immideately connect the usb cable to PC right before it vibrates or exactly when it vibrates (it's a matter of timing), and bingo you are in fastboot and you can flash system.img, recovery.img, cust.img, cache.img and boot.img from there, but this is not how I revived my phone. I used the 3 button method again when the phone was charged for like half an hour or so and the did the same cold boot trick and I could boot into the force upgrade environment (strangely this still didn't work whitout connecting the usb cable to PC), but it somehow didn't want to read the UPDATE.APP that I had in dload folder on my SD card and wanted to have it from my PC (I just felt it nad there was no indication of it ) so then I installed the DC Phoenix tool and payed 15 euros to be able to inject the complete UPDATE.APP to my bricked phone and the installation went well to 99% and failed, but I rebooted the phone and I could boot normally. Just to make sure I did a factory reset afterwards. Hope this helps.
bahador_b_92 said:
I managed to access the fastboot using the 3 button method in cold boot. Hold the Power key until the screen goes off and then release and hold down the Vol- key and immideately connect the usb cable to PC right before it vibrates or exactly when it vibrates (it's a matter of timing), and bingo you are in fastboot and you can flash system.img, recovery.img, cust.img, cache.img and boot.img from there, but this is not how I revived my phone. I used the 3 button method again when the phone was charged for like half an hour or so and the did the same cold boot trick and I could boot into the force upgrade environment (strangely this still didn't work whitout connecting the usb cable to PC), but it somehow didn't want to read the UPDATE.APP that I had in dload folder on my SD card and wanted to have it from my PC (I just felt it nad there was no indication of it ) so then I installed the DC Phoenix tool and payed 15 euros to be able to inject the complete UPDATE.APP to my bricked phone and the installation went well to 99% and failed, but I rebooted the phone and I could boot normally. Just to make sure I did a factory reset afterwards. Hope this helps.
Click to expand...
Click to collapse
Now your phone is OK?
Sent from my NEM-L21 using Tapatalk
Anonda said:
Now your phone is OK?
Sent from my NEM-L21 using Tapatalk
Click to expand...
Click to collapse
Yes. I am actually writing this from my Huawei P9 Lite now. This phone is really a nightmare for modifying and customization. I'm not sure if I'm going to resell it or just wait a reasonable amount of time until some reviews from the next update come out and see if I might wanna take the risk and update my phone again.
Hi, I get this phone yesturday... I've installed last firemware ( 6.0 to 7.0.1 ) and after I tried with Tuliptool to install recovery but after this my phone dont show recovery when I tried so I was thinking I've forget to Unlock it before... and obvously I tried to unlock ( with tulip ) but I got error message in cmd ( I don't remerber... ) and now it show only Zte and it bootloop on it so I didn't have recovery, I can't use edl because I can't boot.. so there is something I can do or I bricked it in less than 1 day.. ? :S
Got the same problem
EDL can only be entered once the phone is completely off. You need to hold down volume up + volume down and then plug in the usb cable (dont touch the power button). The phone wont do anything, it will still look off but you will hear the device plugged in tone in Windows and will be able to find the device in zadiag. Also after a few attempts Windows stopped showing the device and I had to restart Windows before it worked again. Can you get this far?
dmo199 said:
EDL can only be entered once the phone is completely off. You need to hold down volume up + volume down and then plug in the usb cable (dont touch the power button). The phone wont do anything, it will still look off but you will hear the device plugged in tone in Windows and will be able to find the device in zadiag. Also after a few attempts Windows stopped showing the device and I had to restart Windows before it worked again. Can you get this far?
Click to expand...
Click to collapse
no my phone is just showing ZTE when it is booting then just instant turns off and starts again showing ZTE and it is doing that until the battery is empty
I did have that before, I'm not sure the exact combination I used, charge it up and then remove the cable, hold the power button and either the volume up, or volume down or both for anywhere between 5 and 20 seconds before letting go and seeing if it stays off. If it doesn't work try again and again and again, Its completely trial and error and took me a while to get it to work
dmo199 said:
EDL can only be entered once the phone is completely off. You need to hold down volume up + volume down and then plug in the usb cable (dont touch the power button). The phone wont do anything, it will still look off but you will hear the device plugged in tone in Windows and will be able to find the device in zadiag. Also after a few attempts Windows stopped showing the device and I had to restart Windows before it worked again. Can you get this far?
Click to expand...
Click to collapse
I'm not quite sure but on the European version of the Axon you can't do that by holding the buttons.
I understand that the only way to get in edl mode is software, no other choice than rebooting from the OS using the command adb reboot edl. So if you can't make your device completely started first, i guess it's bricked. But maybe i'm totally wrong.
vincent1967 said:
I'm not quite sure but on the European version of the Axon you can't do that by holding the buttons.
I understand that the only way to get in edl mode is software, no other choice than rebooting from the OS using the command adb reboot edl. So if you can't make your device completely started first, i guess it's bricked. But maybe i'm totally wrong.
Click to expand...
Click to collapse
I also messed up mine. I did everything until I had android 7, rooted, but lost IMEI. then I, THE IDIOT, tried to re-flash stcok android 6......booom. bricked.......
however.........power the phone off:
hold vol- power for 10 secs. phone should boot into FTM. then power it off by pressing power for about 5 secs. phone is off.
now vol+power and the phone should go to recovery, even if stuck on the logo, my pc reads it as recovery in adb devices......
tomorrow I'll see if I can get out from there. my experience doing this before is that from the recovery the ADB reboot edl works
cheers
I was messing with my P10 Lite and I accidentally wiped the Vendor partition (not sure if I wiped anything else) with TWRP. After the phone rebooted it said something about a critical error during boot and went into erecovery. It gave me two options( I don't remember the second one) and I chose factory reset. It started doing it's thing but I guess something went wrong because it wasn't able to boot and it started to bootloop.
I managed to get into fastboot once. The bootloader and FRP should be unlocked but I am not sure as I think I semi accidentally used the command to relock the bootloader in the hopes of it doing the automatic low level factory reset. After that restart, the phone wanted to boot up but after the Huawei logo it went into the EMUI logo which I've shown in the pictures. Now I can't use any button combination and can't enter any menu. I also can't shut down the phone as it bootloops into the EMUI logo after I press the power button. I opened the phone and turned it off by detaching the battery cable but after holding the power down key and plugging the usb cable into the phone it still boots into the EMUI logo right after the Huawei logo.
I guess not being able to enter fastboot is the major issue and after hours of googling I am yet to find a solution.
Edit: I am a newb!
Please help!
Why did you delete the vendor partition, you could try plugging the phone into your computer and checking if you can do anything with fastboot while it's showing emui logo?
Alaunus said:
I was messing with my P10 Lite and I accidentally wiped the Vendor partition (not sure if I wiped anything else) with TWRP. After the phone rebooted it said something about a critical error during boot and went into erecovery. It gave me two options( I don't remember the second one) and I chose factory reset. It started doing it's thing but I guess something went wrong because it wasn't able to boot and it started to bootloop.
I managed to get into fastboot once. The bootloader and FRP should be unlocked but I am not sure as I think I semi accidentally used the command to relock the bootloader in the hopes of it doing the automatic low level factory reset. After that restart, the phone wanted to boot up but after the Huawei logo it went into the EMUI logo which I've shown in the pictures. Now I can't use any button combination and can't enter any menu. I also can't shut down the phone as it bootloops into the EMUI logo after I press the power button. I opened the phone and turned it off by detaching the battery cable but after holding the power down key and plugging the usb cable into the phone it still boots into the EMUI logo right after the Huawei logo.
I guess not being able to enter fastboot is the major issue and after hours of googling I am yet to find a solution.
Edit: I am a newb!
Please help!
Click to expand...
Click to collapse
Dload method. Put sd card in other phone or some card readers and put appropriate files.
nemanjsb said:
Dload method. Put sd card in other phone or some card readers and put appropriate files.
Click to expand...
Click to collapse
I've already tried that. I've placed the appropriate files into my SDcard but I can't use any button commands including volume up+down+power. When I press them my device just boots into the EMUI logo and nothing happens.
Edit: It boots into the EMUI logo even if I only press the power button. Pressing volume down + usb also boots me into the EMUI logo
DaarkZek said:
Why did you delete the vendor partition, you could try plugging the phone into your computer and checking if you can do anything with fastboot while it's showing emui logo?
Click to expand...
Click to collapse
I measured once and not trice before cutting... I was also not paying enough attention/in a hurry...
Power OFF the phone.
Press and Hold VOL Down and connect the phone to PC via USB cable. The phone should boot into Bootloader (fastboot mode). Does this method work?
or try this:
Press and Hold VOL Up and connect the phone to PC via USB cable. The phone should boot into eRecovey mode and then then select "Download latest stock rom and install".
Aalesund said:
Power OFF the phone.
Press and Hold VOL Down and connect the phone to PC via USB cable. The phone should boot into Bootloader (fastboot mode). Does this method work?
or try this:
Press and Hold VOL Up and connect the phone to PC via USB cable. The phone should boot into eRecovey mode and then then select "Download latest stock rom and install".
Click to expand...
Click to collapse
Ok, it seems like not all is lost about my phone. I managed to get into fastboot. In my situation, pressing volume down + usb cable while the battery was plugged into the phone did not work. That was before I opened up my phone's case and disconnected the battery cable.
As I mentioned before, I had opened my phone and disconnected the battery cable because that was the only way to shut it off.
What I did after I disconnected the battery cable was the following:
1 - Hold volume down and don't release it
2 - Plug in USB
3 - Plug in the battery cable into the phone's mobo.
That booted me into fastboot. Right now, the phone says my bootloader in unlocked and my FRP is locked. What would be the best way to flash the new stock OS on my phone?
Aalesund said:
Power OFF the phone.
Press and Hold VOL Down and connect the phone to PC via USB cable. The phone should boot into Bootloader (fastboot mode). Does this method work?
or try this:
Press and Hold VOL Up and connect the phone to PC via USB cable. The phone should boot into eRecovey mode and then then select "Download latest stock rom and install".
Click to expand...
Click to collapse
I have downloaded THIS and THIS for the new OS but by talking with Alexxxx1 in THIS discussion I learnt that Huawei has implemented a security patch in their latest update, which I've most likely installed, that prevents you from rolling back your OS version. That means I need to install the .386 version, which should be the last if I am not wrong, instead of the .378 correct? Though I heavily dislike patches like this I guess I can't do anything about that...
I got a replacement device from OP and I was unlocking the bootloader and rooting it. The guide i used had the incorrect patched boot image and everything went bad quick.
I can't go anywhere except fastboot now, can't boot to OS, no OS installed.
TWRP WAS booting from fastboot, I pushed the rom from there and flashed it...said no OS installed after, I installed it on both slots.
I can't get into EDL mode, the volume keys work...I think, but the second I let go of them when it's plugged in it defaults back to fastboot immediately. I tried the bat file that people use, says it worked, phone stays in fastboot.
I even tried holding the volume keys the entire time but the MSM tool wouldn't read it enough to flash anything, although it did read it enough to register some data, but was stuck on "waiting for device".
I am in need of some major help. Now I can't even temp boot to twrp, getting an error failed authorization. I'm afraid I really messed things up.
I have 5 days to send my old device back. Please help!
May be a longshot, but does the stock recovery work? Maybe try sideloading the full OTA zip from there?
Sent from my IN2025 using Tapatalk
For EDL mode, you need to hold the buttons then plug it in while continuing to hold the buttons. It won't work if the phone is already plugged into a usb port and then you try and get into EDL.
Really hard to brick a OnePlus device in my experience.
FernBch said:
May be a longshot, but does the stock recovery work? Maybe try sideloading the full OTA zip from there?
Click to expand...
Click to collapse
Recovery doesn't work. I was able to get to one of the steps to approve going into fastboot, advanced, reboot to fastboot, but not anymore.
Mike02z said:
For EDL mode, you need to hold the buttons then plug it in while continuing to hold the buttons. It won't work if the phone is already plugged into a usb port and then you try and get into EDL.
Really hard to brick a OnePlus device in my experience.
Click to expand...
Click to collapse
I was doing just that. It seemed to work initially but after I plugged it in and released the buttons it went back to fastboot and disconnected from MSM.
Make sure MSM is ready keep vol up/down pressed, connect cable and immediately press Start in the tool. Have done it like this 3-4 times with my Pro
Please read this https://forum.xda-developers.com/showpost.php?p=82508527&postcount=67
and this https://forum.xda-developers.com/showpost.php?p=82658631&postcount=85
both work for me.
lazyd2 said:
Make sure MSM is ready keep vol up/down pressed, connect cable and immediately press Start in the tool. Have done it like this 3-4 times with my Pro
Click to expand...
Click to collapse
I ended up using the fastboot ROM flash all.bat from this thread: https://forum.xda-developers.com/oneplus-8-pro/how-to/rom-stock-fastboot-roms-oneplus-8-pro-t4083997
I am now booting into the OS and the stock recovery came back. So good news is the phone isn't bricked.
Glad you sort it out
lazyd2 said:
Make sure MSM is ready keep vol up/down pressed, connect cable and immediately press Start in the tool. Have done it like this 3-4 times with my Pro
Click to expand...
Click to collapse
lazyd2 said:
Make sure MSM is ready keep vol up/down pressed, connect cable and immediately press Start in the tool. Have done it like this 3-4 times with my Pro
Click to expand...
Click to collapse
It work, thanks
You're a life saver