After I unboxed the phone, it was working with an AT&T sim card for few hours. When I got home where I have wifi, I updated the software and didn't pay much attention to it. few hours later i found out the phone can no longer read any sim cards. I tried both sim slot, different sim cards. factory reset and etc.
Is there any way I can download the software and re-do it before sending it back to Asia for repair?
Related
So I have this Tmobile wing for 2 weeks and it worked fine until today.
I turned on the phone and the network couldn't be found.
I went outside and still nothing and I am using OpenTouch. can someone help me figure this out?
Have you tried a soft reset or a power cycle? If that doesn't work, consider taking out the sim card and reinserting it.
I had the same problem yesterday. I pulled out my sim card and put it in another phone to see if it was my sim and sure enough the other phone could not find a network. so i put in a new sim and called t-mobile and works fine now
Hello All,
I am using HTC touch for a while and would use different ROM versions quite often. Recently i put in the some ROM which event i don’t remember which one i started getting this error below. I checked and made sure that there is nothing in the SIM card i also put in the SIM in different Cell phone to make sure its blank. I also reverted the device to the Factory Image but still the same issue. There is no pattern on when i get this error it would some time come twice in 1 hour and some time it would be couple of hours. Once i get this error and select Ok my network will go to searching and often end up enable Flight Mode and then disabling it.
"SIM card full. The SIM card is full. You must remove some messages from your SIM card to receive incoming SIM messages."
Any pointers are greatly appreciated.
Thanks,
Jasjit
it will be necessary for you to call the carrier to locate a retail location near you that has a Cellebrite device... not all locations have one as they are quite expensive... using the Cellebrite it is possible to wipe/edit your SIM...
this happens sometime with my device also.
but in my case i just clean simcard and reinsert it.
may be u have faulty simcard or sim socket .
I have a extremely illogical problem and spent alot of time diagnosing it which still got me nowhere.
The scenario is like this,
I have 2 S4 galaxies, (both unlocked australian models)
1. I9505 (Stock 4.4.2)
2.I9507 (Stock 4.2.2)
I have a very old sim card that has been working on all my phones so far, android and others. It is a Australian TPG sim card which uses the optus network
I insert this sim card in my I9505 20 or 30 times and power on off, always have message no sim card. I try at least 5 other sim cards, different carrier and different country all detect and work on first attempt.
I now insert this sim card into phone 2 (I9507) it detects on first attempt! I do it 3 more times all attempts are successful.
So I open both phones, swap the sim card / sd card reader parts between phones (I mark each sim card reader so there is no confusion which one is which)
Now I insert sim card into (I9505 with I9507 sim reader) sim card not detected, 10 attempts all fail.
Insert sim card into (I9507 with I9505 sim reader) sim card detected every time!
I try all my sim cards on both phones, all sim cards work on both phones, both sim readers are 100% fine!
I am thinking this has to be software related, I am not able to downgrade my I9505 to 4.2 obviously, I do not want to upgrade my 9507 to 4.4.2, to see if the sim will fail on the i9507.
the 9505 has the 4.4 bootloader and knox has been tripped, but it works fine with all other sim cards, phone calls, data, wifi etc.
Anybody have anything in mind or any clue why in the hell the sw on the i9505 hates my tpg sim and won't detect it, obviously the sim reader is working 100% and the sim card also works 100% detects on i9507 and also on a xt925 motorola (pre 4.4 bootloader)
The only thing in this equation thats out of place is 4.4 bootloader, I have no second device with 4.4 bootloader to verify.
is there any new security or anything at all regarding sim card reading in the 4.4 bootloader?
Any help appreciated, hope its not a thread with 0 answers after a year
ps tpg charge $20 for sim replacement and take upto 10 days in mail, so I am keen to solve this before replacing the sim
The problem was hardware wise afterall, all other sim cards worked under normal conditions however the non working simcard started working when heavy pressure is applied on the sim reader flex cable plug. Solution was to put a rubber stopped on top of the sim reader flex cable plug. When the midframe is screwed down the rubber stopper puts the extra pressure needed.
Something to point out for those purchasing SIM card slot replacements. The original part HAS the rubber pad mentioned above. If you replace the SIM card reader with a new one you have to peel the pad off the original and place it on the new part for it to work correctly. The new part doesn't include the pad.
Have the same problem with my s4 i9505 . I flashed 4.4.2 official rom then custom roms with no results . But when i changed sim card with other of the same operator it worked . I realized that the problem lies in the new sim cards pins engineering.
Hi, I recently bought a new Yotaphone2 (YD206) taking advantatge of the Singles' day discounts, but I am having some trouble connecting to the mobile network.
Since I did not have a nanosim available from the beggining, I started by updating its ROM (I used the last Russian one, while keeping the Chinese radio) and then I rooted it. So far so good.
The thing is, after my microsim was cut into a nanosim (the guy at the mobile phone store did it, using one of these "staplers"), I inserted it in the tray but it is not recognized on the phone. On the screen you can read "No sim card - emergency calls only".
At first I thought it was the radio, and I even flashed it again. I also went back to the original chinese rom, with no success. I think it's not a radio problem, since I can get some statistics in the *#*#4636#*#* menu, but I am not a 100% certain. Of course, I've already tried rebooting, setting the airplane mode on and off, removing and inserting the sim again, etc. Apart from that, wifi, bluetooth and everything else work as expected.
The sim card works, because using a microsim adapter I can fit it in my Nexus 4 and it gets signal. There are three options here: either the radio is not properly configured/flashed, the phone is faulty or the sim has been wrongly cut.
Could you help me troubleshoot the problem?
Solved!
Solved! It was the sim card, it was not properly cut. I used some sandpaper so sand one edge that was a bit rough. I didn't even have to reboot, the phone asked for my pin inmediately. I'm using the last EU rom with the chinese radio.
Yay! Happy!
I have the same issue now and my yotaphone 2 was bought in China... I've tried the sim cards from two companies, both didn't work. I doubt I received a defective product.
So I got the phone Friday and everything was working perfectly except for the texting coming so I called Verizon and had them the cdma_less feature. After that my text came flooding in. So I used the phone all day and later on I lost signal completely. So I shut my phone off and on multiple times and I would get LTE but no voice over LTE so I couldn't make phone calls and then my phone signal stopped again.
I called technical support and they did a bunch of resets on the network side and still couldn't get it working so they suggested that I get a new SIM card. I got a new SIM card and still didn't work so I called technical support again and they went through a bunch of things with me and finally they had me move it over to SIM card slot 2. They did get it going in SIM card slot 2 but I've also read people online having troubles with this when they had it in sim 2 and that most were using sim 1.
Has anyone else had this issue and what slot are you using? I'm worried that it's going to happen again. Which SIM card slot are you using and do you think the SIM card slot is an issue? I don’t understand why it would work for a whole day in slot 1. Thanks in advance.
umass021 said:
So I got the phone Friday and everything was working perfectly except for the texting coming so I called Verizon and had them the cdma_less feature. After that my text came flooding in. So I used the phone all day and later on I lost signal completely. So I shut my phone off and on multiple times and I would get LTE but no voice over LTE so I couldn't make phone calls and then my phone signal stopped again.
I called technical support and they did a bunch of resets on the network side and still couldn't get it working so they suggested that I get a new SIM card. I got a new SIM card and still didn't work so I called technical support again and they went through a bunch of things with me and finally they had me move it over to SIM card slot 2. They did get it going in SIM card slot 2 but I've also read people online having troubles with this when they had it in sim 2 and that most were using sim 1.
Has anyone else had this issue and what slot are you using? I'm worried that it's going to happen again. Which SIM card slot are you using and do you think the SIM card slot is an issue? I don’t understand why it would work for a whole day in slot 1. Thanks in advance.
Click to expand...
Click to collapse
I have been having this same issue after updating to 9.0.10. I was on the phone with Verizon and OnePlus for 50 minutes. Still have not gotten the issue resolved.
If anyone has any insight, it would be greatly appreciated.
Have you switched Sim card slots? Ever since I went from 1 to 2 I haven't had one issue
I read somewhere that a factory reset fixes it
9.0.10 breaks Verizon connectivity. You might get some LTE, but no voice or messaging. Looks like people can fix it with a factory reset.
FYI: Same issue on the new beta.
chrisliphart said:
9.0.10 breaks Verizon connectivity. You might get some LTE, but no voice or messaging. Looks like people can fix it with a factory reset.
FYI: Same issue on the new beta.
Click to expand...
Click to collapse
I tried everything except for a factory reset on 9.0.10. Decided to try the open beta. That resolved the issue for me.
Are you forcing the update by using a VPN or getting it OTA?